Master Catalog
Clocks Section
Product/Technical Bulletin
Issue Date
125
C
BOX-7355-1
0795
BOX-7355-1 Metal Indoor Enclosure
The BOX-7355-1 enclosure provides a rugged and
secure housing for C-7355 Series Time Clocks. The
BOX-7355-1 is a NEMA 1-rated metal enclosure with
conduit knockouts and a window, which allows full
view of the time and On/Off status of the time clock.
Figure 1: BOX-7355-1 Enclosure
Features and Benefits
‰
‰
Steel Construction
Provides a sturdy housing for mounted time clock
NEMA 1 Rated
Complies with National Electrical Code for line
voltage wiring
‰
Padlock Hole
Prevents unauthorized access to mounted time
clock
© 1995 Johnson Controls, Inc.
Part No. 24-7664-443, Rev. —
Code No. LIT-216133
1
P roduct Dimensions
3-5/16
84
2-5/16
59
4-3/4
121
2
51
6-1/4
159
3-3/16
81
1-3/4
44
1-1/8
29
2-1/2
64
Figure 2: BOX-7355-1 Dimensions (in./mm)
S upplies Needed
K it Contents
•
mounting hardware (field supplied)
Table 1: Contents of Kit
•
screwdriver
•
marking pencil
Enclosure
1
•
wire stripper
Time clock mounting screws
(4-40 x 1/2 in. Phillips-head screws)
2
•
1/4 in. nut driver
Enclosure closing screw
(self-tapping 1/2 in. hex-head screw)
1
Item
2 BOX-7355-1 Metal Indoor Enclosure Product/Technical Bulletin
Quantity
I nstallation
Enclosure
Mounting Hole
Use the following instructions to mount the enclosure
and the C-7355 time clock. Refer to the time clock
instructions for an exploded illustration of the time
clock.
C-7355-10
Time Clock
Mounting Holes
1. Remove the enclosure cover.
2. Remove the appropriate enclosure knockout to be
used.
C-7355-7, -8, -9
Time Clock
Mounting Holes
3. Using the back of the enclosure as a template,
mark the location of the three mounting holes.
See Figure 3.
4. Mount the back of the enclosure at the marked
locations using field supplied hardware.
Enclosure
Mounting Holes
5. Connect conduit hubs to conduit before connecting
the hubs to the enclosure.
6. Tighten hub lock nut to the enclosure.
Screw
Terminal Base
7. Remove the clear cover from the front of the time
clock.
Enclosure Back
8. Using a screwdriver, loosen the two captive
screws located in the upper and lower corners of
the time clock housing.
9. Remove the time clock housing by pulling forward.
Align the mounting
holes of the time
clock's terminal
base with the
mounting holes
shown above for
the appropriate
time clock and
secure with the two
1/2 in. Phillips-head
screws provided.
Figure 3: Enclosure and Time Clock
Mounting Holes
10. Remove the time clock terminal cover by pulling
forward.
11. Secure the time clock terminal base to the
enclosure back using the two 1/2 in. Phillips-head
screws provided with the enclosure. See Figure 3
for mounting hole locations.
12. Make wiring connections (refer to Wiring section of
the time clock instructions). Using pliers, remove
the appropriate knockouts on the terminal cover for
wire entry.
13. Replace the time clock terminal cover and housing;
tighten the captive screws; and replace the clear
cover.
14. Place the enclosure cover on the enclosure back
by sliding it downward over the back.
15. Secure the enclosure cover to the back using the
self-tapping 1/2 in. hex-head screw provided with
the enclosure. See Figure 4 for screw location.
Insert padlock (if desired)
for added security.
Insert the provided self-tapping
1/2 in. hex-head screw to secure
the enclosure cover to the back.
Figure 4: Enclosure Cover Holes
BOX-7355-1 Metal Indoor Enclosure Product/Technical Bulletin
3
Specifications
Product
BOX-7355-1 Metal Indoor Enclosure with Window
Material
Steel
Mounting
Surface
NEMA Rating
NEMA 1
Dimensions (H x W x D)
Shipping Weight
6-1/4 x 4-3/4 x 3-5/16 in. (159 x 121 x 84 mm)
1.2 lb (0.524 kg)
The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these specifications,
consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or misuse of its products.
Controls Group
507 E. Michigan Street
P.O. Box 43
Milwaukee, WI 53201
4 BOX-7355-1 Metal Indoor Enclosure Product/Technical Bulletin
Printed in U.S.A.