TEMP RANGE: -20ºC-+50ºC MASTER W SLAVE Instructional Sheet Part Number: EZD-1CPB Controller: EZD-4C8A or EZD-1C8A EZD-1CPB Wireless LED Dimmer Push Button Push Button Switch Switch for Easy Dimmer Series Controllers EZD-4C8A Controller Parts Included 1 1 - 868MHz LED Dimmer Push Button Switch 1 - 3V CR2025 Battery 2 - Mounting Screws EZD-1C8A Controller Hold Press Increases or decreases brightness until you release, turning LED on will remember the last memory position CH1 tc=75ºC 0.5-2.5mm² 6-7mm Pairing Switch Button Actions: Turns LEDs on/off. If the Controller Pairing Switch has been depressed, a single press on the Push Button Switch pairs the switch to the Controller. Push Switch GND Easy Dimmer Series PRI: Uin=12-36VDC lin=8.3A SEC: Uout=1x(12-36)VDC Iout=1x8A Pout=1x(96-288)W TEMP RANGE: -20ºC-+50ºC INPUT 12-36VDC EZD-1C8A 1. On/Off/Brightness Push Button Press switch for remotely activating / controlling LED products. Single Press Pairing Switch MASTER Push Button Switch 12/36VDC V- DC INPUT V+ EZD-1CPB Push Button Switch Operating Voltage 3 VDC Battery Size CR2025 Operating Frequency 868 MHz FCC ID# 2ACUQ-RF28XX01 EZD-4C8A Easy Dimmer Series PRI: Uin=12-36VDC lin=8.3A SEC: Uout=1x(12-36)VDC Iout=4x8A Pout=1x(96-288)W TEMP RANGE: -20ºC-+50ºC OUTPUT Important: Read all instructions prior to installation. V+ CH1 CH2 CH3 CH4 SLAVE EZD-4C8A Controller Input Voltage Current Output Wattage 12~36 VDC 4 X 8A 384W(12V) 768W(24V) 1152W(36V) EZD-1C8A Controller Input Voltage Current Output Wattage 12~36VDC 1 X 8A 96W(12V) 192W(24V) 288(36V) FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Controller 1. Pairing Switch To pair Push Button Switch to Controller, press the Controller Pairing Switch once and then press Push Button Switch. Lights will blink once to indicate pairing. To unpair Push Button Switch(es), press and hold Controller Pairing Switch until lights blink twice. 2. Master/Slave Jumper Set Jumper to Master for main Controller. Master emits synchronization signal to Slave Controllers. Set Jumper to Slave to receive synchronization signal from Master Controller. Use Master for the first Controller in each zone. To achieve perfect synchronization between Controllers in one zone, set additional Controllers to slave. Safety Set-Up Instructions Remote 1. Follow illustrated steps to remove the Battery Tray. Insert the 3V battery included with the Push Button Switch. Controller 1. Make sure power to the Controller is disconnected. 2. Using a small flathead screwdriver, loosen the labeled terminal screws visible on the top of the controller. 3. Matching light strip wires with labeled slots on the Controller, insert wires and tighten terminal screws. 4. Turn power on and wait until light strip illuminates. If it does not come on, check light strips and wiring connections. • • DO NOT install with power applied to controller. DO NOT expose the Push Button Switch or Controller to moisture. Battery Replacement Instructions 4. If replacing battery: Push old battery down-and-out of it’s slot. 5. Insert the 3V (CR 2025) battery, push PCB board back into front plate along with the power button. Push back plate into place to complete the assembly. 1. Follow illustrated steps to replace the battery. 2. Locate notch in the back plate. Use a flat-head screwdriver to remove back plate from the housing. 3. Remove PCB board completely from the front housing. Cove Lighting Application Power Supply Controller connected to multiple in-line LED strips Operating the Push Button Switch/Controller 1. Press “Pairing Switch” button on the Controller. Immediately press the Push Button Switch to pair it to the Controller. The LED lights wired to the Controller will blink when the pairing is complete. Switch 2. Multiple Push Button Switches can be paired to a Controller, and Push Button Switches can be paired to multiple Controllers. If multiple Controllers paired to a Push Button Switch are not in sync, unpair and then pair until Controllers and lights are in sync. 4400 Earth City Expy, St. Louis MO 63045 Wireless Signal to Controller 866-590-3533 support@superbrightleds.com EZD-4C8A V+ Easy Dimmer Series PRI: Uin=12-36VDC lin=8.3A SEC: Uout=1x(12-36)VDC Iout=4x8A Pout=1x(96-288)W TEMP RANGE: -20ºC-+50ºC OUTPUT 12/36VDC V- DC INPUT V+ CH1 Instructional Sheet Pairing Switch MASTER W B R G + Important: Read all instructions prior to installation. To Additional Controllers From Power Supply EZD-4C8A Controller Supply DC 12V In CH3 Part Number: CH4 SLAVE EZD-1CPB W B R G + W B R G + W B G R V+ W B R G + Controller: EZD-4C8A or EZD-1C8A NFLS-RGBNW300X4-24V Wireless LED Dimmer Push Button Switch for Easy Dimmer Series Controllers From DC 12V Out Connection Diagram Power CH2 W B R G + To Additional Controllers 12VDC Out 12VDC In W B R G + Switch CH4 W B R G + W B R G + Jumper W B R G + W B R G + Common Anode Output (+) V+ V+ CH1 V- Pairing Switch CH2 MASTER EZD-4C8A Easy Dimmer Series PRI: Uin=12-36VDC lin=8.3A SEC: Uout=1x(12-36)VDC Iout=4x8A Pout=1x(96-288)W TEMP RANGE: -20ºC-+50ºC OUTPUT CH2 OUTPUT OUTPUT PRI: Uin=12-36VDC lin=8.3A SEC: Uout=1x(12-36)VDC Iout=4x8A W B G R V+ Pout=1x(96-288)W TEMP RANGE: -20ºC-+50ºC CH3 Pairing SLAVE Easy Dimmer Series 12/36VDC Master/Slave MASTER V+ CH1 V- EZD-4C8A DC INPUT Pairing Switch Easy Dimmer Series PRI: Uin=12-36VDC lin=8.3A SEC: Uout=1x(12-36)VDC Iout=4x8A Pout=1x(96-288)W TEMP RANGE: -20ºC-+50ºC DC INPUT Pairing Switch EZD-4C8A 12/36VDC (-) V- 12/36VDC V+ DC INPUT Power In V+ (+) CH4 1 Output (-) CH2 CH3 Channel 2 Output (-) CH4 SLAVE Channel 3 Output (-) CH3 MASTER SLAVE NFLS-RGBNW300X4-24V V+ CH1 Channel Channel 4 Output (-) NFLS-X3-LC2 B R G + B R G + B R G + B G R V+ B R G + B R G + NFLS-RGBX2-LC4 EZD-1C8A Controller EZD-1C8A B R G + B R G + _ _ + + _ _ + + _ + + _ _ + + MASTER _ _ + + From Power Supply 12VDC In _ To Additional Controllers 12VDC Out + OUTPUT _ + _ _ + + _ _ + + _ _ + + _ _ + + _ + + _ _ + + V+ V+ CH1 V- CH2 Pairing Switch MASTER _ + EZD-4C8A _ + _ _ + + _ _ + + _ _ + + 12/36VDC DC INPUT V- PRI: Uin=12-36VDC lin=8.3A SEC: Uout=1x(12-36)VDC Iout=4x8A Pout=1x(96-288)W TEMP RANGE: -20ºC-+50ºC MASTER OUTPUT Optional Push Switch Pairing Switch Single Press Turns LEDs on/off Increases or decreases LED Hold Press intensity until you release _ + + + _ + _ _ + + _ + _ _ + + _ + Easy Dimmer Series _ _ + + V+ CH1 CH2 CH3 CH4 _ _ + + V+ CH1 Easy Dimmer Series PRI: Uin=12-36VDC lin=8.3A SEC: Uout=1x(12-36)VDC Iout=1x8A Pout=1x(96-288)W TEMP RANGE: -20ºC-+50ºC _ _ + + _ + _ _ + + _ + tc=75ºC From Power Supply 12 VDC In 0.5-2.5mm² 6-7mm CH2 Pairing Switch CH3 CH4 SLAVE _ _ + NFLS-NW300-WHT-LC2 _ + EZD-1C8A Push Switch GND Easy Dimmer Series _ + NFLS-R300-WHT-LC2 EZD-4C8A + _ Optional Push Switch NFLS-G300-WHT-LC2 (See below for operation) V+ _ CH1 + + NFLS-B300-WHT-LC2 INPUT 12-36VDC _ + _ + SLAVE + _ _ NFLS-NW300-WHT-LC2 (3) SingleToColor Additional12VDC Controllers Application / EZD-1C8A 12VDC Out CH3 PRI: Uin=12-36VDC lin=8.3A SEC: Uout=1x(12-36)VDC Iout=4x8A Pout=1x(96-288)W TEMP RANGE: -20ºC-+50ºC NFLS-NW600X2-24V-LC2 From Power Supply 12VDC In Power In CH2 NFLS-R300-WHT-LC2 NFLS-NW600X2-24V-LC2 _ V+ CH1 NFLS-G300-WHT-LC2 CH4 + Easy Dimmer Series CH4 CH3 _ (+) PRI: Uin=12-36VDC lin=8.3A SEC: Uout=1x(12-36)VDC Iout=4x8A Pout=1x(96-288)W TEMP RANGE: -20ºC-+50ºC (2) Four Color 12VDC Application / EZD-4C8A + SLAVE + NFLS-NW600X2-24V-LC2 _ Easy Dimmer Series PRI: Uin=12-36VDC lin=8.3A SEC: Uout=1x(12-36)VDC Iout=4x8A Pout=1x(96-288)W TEMP RANGE: -20ºC-+50ºC _ SLAVE 12/36VDC Pairing Switch EZD-4C8A + (-) Pairing Switch DC INPUT 12/36VDC DC INPUT V- _ + Channel 1 Output (-) EZD-4C8A NFLS-NW600X2-24V-LC2 V+ _ NFLS-NW600X2-24V-LC2 NFLS-NW600X2-24V-LC2 _ + Anode Ouput (+) CH1 V- B R G + B R G + _ OUTPUT OUTPUT + NFLS-X3-LC2 B R G + + B G R V+ (1) Single Color 24VDC Application / EZD-4C8A To Additional Controllers 24VDC Out _ + MASTER NFLS-RGBX2-LC4 From Power Supply 24VDC In _ V+ CH4 SLAVE Pairing Switch Example Diagrams tc=75ºC 6-7mm _ + NFLS-NW600X2-24V-LC2 0.5-2.5mm² CH3 _ NFLS-NW600X2-24V-LC2 + MASTER + + Pairing Switch Easy Dimmer Series PRI: Uin=12-36VDC lin=8.3A SEC: Uout=1x(12-36)VDC Iout=4x8A Pout=1x(96-288)W TEMP RANGE: -20ºC-+50ºC _ + 12/36VDC Pairing Switch EZD-4C8A _ DC INPUT 12/36VDC V- DC INPUT V+ Push Switch GND Easy Dimmer PRI: Uin=12-36VDC lin=8.3A V+ SEC: Uout=1x(12-36)VDC CH1 Iout=1x8A CH2 Pout=1x(96-288)W TEMP RANGE: -20ºC-+50ºC To Additional Controllers 24VDC Out From Power Supply Series 24VDC In OUTPUT 12VDC Out (See below for operation) Power Supply 12VDC In INPUT 12-36VDC Optional PushControllers Switch To Additional From _ _ + + _ + NFLS-NW300-WHT-LC2 _ _ + + _ _ + + _ 4400 Earth City Expy, St. Louis MO 63045 NFLS-B300-WHT-LC2 + 866-590-3533 support@superbrightleds.com