Belt Grinder -Backbone make one weld together,
4 places cut a 1/16" x ¾” clearance slot the entire length on the inside of the ½” x 2" flat bar tap ½-20
¼” x 2" flat bar
½” x 2" flat bar
2.030"
¼” x 2" flat bar
0.530"
¼” x 2" flat bar file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

Belt Grinder -Bearing Plate make one
Bearing Plate, 3/8" f;at bar. weld the
Backbone to the
Bearing Plate take appropriate steps so that after welding this angle is precisely 90 degrees since it affects belt tracking drill appropriate pattern to mount two pillow block bearings to the plate
6.000"
7.000" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

Belt Grinder -Tracking Arm Bracket make one
6.500" take appropriate steps so that after welding this angle is precisely 90 degrees since it affects belt tracking drill 0.500"
0.750" weld ½” x 2" flat bar to the frame to form the tracking arm bracket file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

Belt Grinder -Pedistal make one
1-1/2" square tubing with 3/16" or 1/4" wall drill and tap square tubing
½-20, then weld nut over the hole to increase the number of threads weld 1" x 0.250" wall DOM tubing to square tubing.
2.000"
8.000"
33.000"

Belt Grinder -Backbone and Pedistal Assembly make one weld Backbone to Pedistal

Belt Grinder -Stand make one
10.000" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011
10.000"
10.000"
1-½” square tubing with
3/16" or ¼” wall electrical switch box
1" square bar
18.000"
10.000"

Belt Grinder -Tracking Adjustment Block make one
½” x 4" flat bar drill 0.250",
2 places tap 3/8-24
1.000" 1.000" 1.000" 1.000"
0.500"
0.750"
3.000"
3.500" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

Belt Grinder -Tracking Adjustment Lever make one tap ¼-20 drill 0.500"
8.000"
1.500" weld 1/2" x 1-½” flat bar to Tracking
Adjustment Block file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

Belt Grinder -Tracking Adjustment Arm make one
½” x 2" flat bar,
2 places tap ½-13 file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011
1.000" 1.000" drill 0.250"
1.125"
0.250"
1.500"
3.000" weld two pieces together

Belt Grinder -Vertical Platen Frame make one
3/8" x 6" flat bar
1/4" radius, drill 0.500" drill 0.500" tap ½-13,
3 places
3/8" radius, drill 0.750"
Tap 3/8-16,
4 places
0.750"
1.125"
1.500"
1.750"
2.250"
3.000"
4.000"
6.000"
1.250"
2.250"
3.875"
4.250"
5.000"
5.750" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

Belt Grinder -Tool Rest make one file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011
2.500" cut away this area
0.750"
0.750"
3" angle iron with ¼” wall tap ½-13 then weld a nut over the hole to increase the number of threads

Belt Grinder -Tool Rest Support Arm make one round end,
2 places
½” square bar,
4 places, welded together drill 0.500"
9.500"
8.750"
2.500"
0.750" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

Belt Grinder -Vertical Platen Extension Arm make one
½” x 2" flat bar
21.000" tap ½-13,
2 places
2.500" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

Belt Grinder -Platen Clamp make one
2.500"
4.000"
3/8" x 1-½” flat bar drill
0.500",
2 places file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

Belt Grinder -Motor Mount make one
1.750"
0.750"
2.250"
7.000" drill 0.375".
4 places
¼” x 1" flat bar,
4 places drill 0.500",
2 places
1.000" 4.875"
6.875" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011

Belt Grinder -Vertical Platten Bracket make two
1.50"
5.000" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 tap ¼-20 and countersink
1.000"
1.000"

Belt Grinder -Vertical Platten make one
¼” x 2" flat bar of stainless steel or other wear resistant material countersink all the way through, 2 places file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011
1.000" 1.000"
1.750"
4.250"
6.000"