LIGHT DUTY COMMERCIAL ELECTRIC
WATER HEATERS
Available in 30, 40, 50, 66, 80 and 120 Gallon Tall ––
30, 40 and 50 Gallon Low Boy
LIGHT DUTY COMMERCIAL ELECTRIC FEATURES
•
•
SURFACE MOUNT THERMOSTATS – Fully automatic for temperature control.
•
SELF-CLEANING – turbulence inducing cold water inlet-tube engineered to diminish
hard water area sediment deposits.
•
NON-CFC FOAM INSULATED – full 2” foam insulation saves energy and reduces
fuel costs by maximizing heat retention.
•
•
HEAVY GAUGE STEEL TANK – for extra years of trouble-free service.
•
•
MAGNESIUM ANODE ROD – to prolong tank life.
•
FACTORY INSTALLED DIELECTRIC HOT AND COLD WATER CONNECTIONS –
3 4” NPT water connections to extend tank life and for easier installations.
•
•
•
BRASS DRAIN VALVE – Durable and to prevent unintentional breakage.
•
FACTORY INSTALLED ENERGY CUT-OFF SYSTEM – manual reset energy cut-off
prevents overheating.
•
CERTIFIED BY UNDERWRITERS LABORATORIES – listed to UL 174, meets or
exceeds efficiency requirements of the Department of Energy, ASHRAE Standard
90.1 b-1992. National Appliance Energy Conservation Act, ANSI requirements, are
CEC listed and tested in accordance with D.O.E. test procedures and all state
energy efficiency standards.
DUAL HEATING ELEMENTS – Screw-in, direct immersion, 4500 watt, 240 volt
incoloy heating elements for maximum efficiency. Available in 120, 208, 240, 277
and 480 voltages, single- or three-phase. Wattages available up to 12KW.
GLASS-LINED TANK – inner tank glass-lined with Dura-GlasTM and fired at 1600º F
for optimum protection from the effects of corrosion.
ELECTRIC JUNCTION BOX – for 1/2” or 3/4” conduit.
FACTORY INSTALLED HEAT TRAPS – reduces standby heat loss in water piping.
TEMPERATURE AND PRESSURE RELIEF VALVE – Factory provided T & P Valve
can be relocated from side to optional top opening.
TESTING & CERTIFICATIONS
• AMERICAN STANDARD commercial electric water heaters ––
THESE WATER HEATERS MEET OR EXCEED
ASHRAE 90.1B-1992 STANDARD
AND ARE LISTED WITH THE
CALIFORNIA ENERGY COMMISSION.
are certified at 300 PSI test pressure and 150 PSI working pressure,
and all tanks are 100% hydrostatically tested at the factory
• UL Listed
WARRANTY
• Three year limited warranty on inner glass-lined tank.
• One year limited warranty on all other component parts.
AMERICAN STANDARD WATER HEATERS • 1 800 900 9063 • FAX 909 392 7302
LIGHT DUTY COMMERCIAL ELECTRIC MODELS
SPECIFICATIONS & APPLICATION DATA
DIMENSIONS IN INCHES
MODEL
NUMBER
TALL
LD-CE-30-T-AS
LD-CE-40-T-AS
LD-CE-50-T-AS
LD-CE-66-T-AS
LD-CE-80-T-AS
LD-CE-120-T-AS
GAL
30
40
50
66
80
119
LD-CE-30-S-AS
LD-CE-40-S-AS
LD-CE-50-S-AS
30
40
50
LOW BOY
JACKET
DIAM*
WATER
CONN
FLOOR TO
TOP OF
HEATER
22 1/4
24 1/4
26 1/4
32 3/8
34 7/8
34 1/2
A
18 1/4
20 1/4
22 1/4
22 1/4
24 1/4
28 1/4
B
48 3/4
49 5/8
49
62
62 3/8
65 3/4
COLD
CONNECTION
ANODE
ROD
A
B
D
C
For floor to optional Top T & P Outlet see dimension “C”
5000
5500
6000
7000
8000
9000
10000
11000
12000
51
56
61
72
82
92
102
113
123
GPH RECOVERY CAPACITIES
TEMPERATURE RISE
50º F
25
29
33
37
41
45
49
57
66
74
82
90
98
STANDARD
29 5/8
32 1/8
31 3/4
23 3/4
25 1/4
24 5/8
8
8
8
E
8
8
8
8
8
8
MAXIMUM
60º F
20
24
27
31
34
38
41
48
55
61
68
75
82
70º F
18
20
23
26
29
32
35
41
47
53
59
64
70
80º F
15
18
20
23
26
28
31
36
41
46
51
56
61
STANDARD
VOLTAGE
240
240
240
240
240
240
KW
INPUT
12
12
12
12
12
12
SHIP WGT
(LBS)
98
112
150
205
231
328
240
240
240
12
12
12
102
143
189
SINGLE PHASE FULL LOAD AMPERAGE DRAW
E
40º F
31
36
41
46
D
40 1/4
41
40 1/4
53
52 7/8
55 1/8
WTR
SPREAD
*FOR BACK TO FRONT OF HEATER ADD 2 1/8” TO “A” TO ALLOW FOR UPPER DOOR DEPTH
HOT
CONNECTION
WATTS
3000
3500
4000
4500
C
46
46 7/8
46 1/4
59 1/4
59 5/8
63
SIDE
T&P
90º F
14
16
18
20
23
25
27
32
36
41
46
50
55
100º F
12
14
16
18
20
23
25
29
33
37
41
45
49
ELEMENT
WATTAGE
120 V
208 V
240 V
277 V
480 V
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
7000
8000
9000
10000
11000
12000
12.5
16.7
20.8
25.0
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
7.2
9.6
12.0
14.4
16.8
19.2
21.6
24.0
N/A
28.8
33.7
38.5
43.3
48.1
N/A
N/A
6.3
8.3
10.4
12.5
14.6
16.7
18.8
20.8
22.9
25.0
29.2
33.3
37.5
41.7
45.8
50.0
5.4
7.2
9.0
10.8
12.6
14.4
16.2
18.1
19.9
21.7
25.3
28.9
32.5
36.1
39.7
43.3
3.1
4.2
5.2
6.3
7.3
8.3
9.4
10.4
11.5
12.5
14.6
16.7
18.8
20.8
22.9
25.0
THREE PHASE FULL LOAD AMPERAGE DRAW
INTERLOCKING OPERATION SIMULTANEOUS OPERATION
All Terminals L1, L2 and L3
Terminal L3 / Terminals L1 and L2
ELEMENT
WATTAGE
208 V
240 V
480 V
208 V
240 V
480 V
3000/3000
4000/4000
4500/4500
5000/5000
5500/5500
6000/6000
14.4
19.2
21.6
24.0
N/A
N/A
12.5
16.7
18.8
20.8
22.9
25
6.3
8.3
9.4
10.4
11.5
12.5
25.0/14.4
33.3/19.2
37.5/21.6
41.6/24.0
N/A
N/A
21.7/12.5
28.9/16.7
32.5/18.8
36.1/20.8
39.8/22.9
43.3/25.0
10.8/6.3
14.4/8.3
16.4/9.4
18/10.4
19.9/11.5
21.7/12.5
Water Heaters
2808 Metropolitan Place • Pomona • CA 91767
1 (800) 900-9063 • (909) 392-0230 • Fax (909) 392-7302
Commercial Electric Water Heaters
Models
CE-52-AS
CE-80-AS
CE-120-AS
Gallon Capacity
52
80
119
American Standard Commercial Electric Models;
CE-52-AS, CE-80-AS, and CE-120-AS are designed for
point-of-use installations where large quantities
of hot water are required on a commercial basis.
Customary applications include industrial buildings,
motels, hotels, schools, hospitals, restaurants, laundromats, car washes and multi-family developments.
COMMERCIAL ELECTRIC WATER HEATER FEATURES
• Heavy Gauge Steel Tank.
• Inner Tank Glasslined With Dura-Glas™ —
fired at 1600˚F for optimum protection from the effects of corrosion
• Three Full Inches Of Non-CFC, Energy-Saving Foam Insulation —
R-24 value insulation reduces fuel cost by maximizing heat retention
• Multiple Anode Rods To Ensure Longer Tank Life !
• Dry-fire Protection & Reduced Lime Accumulation
with low watt density screw in incoloy elements
• Individual Thermostat For Each Heating Element —
for variable temperature control
• Thermostat Control Is Fully Adjustable To 180°F
• Heating Elements & Thermostat Controls Are Fuse-Protected
• Factory Installed Energy Cut-off System
• Factory Pre-wired Control Box
• Factory Supplied Pressure/Temperature Relief Valve
• Easy Tank Inspection & Easy Removal of Sediment —
with a full-sized hand-hole cleanout
TESTING & CERTIFICATIONS
• AMERICAN STANDARD commercial electric water heaters —
are certified at 300 PSI test pressure and 150 PSI working pressure,
and all tanks are 100% hydrostatically tested at the factory
• UL Listed and CSA certified to meet NSF/ANSI 5 Standards.
WARRANTY
• Three year limited warranty on inner glass-lined tank.
THESE WATER HEATERS MEET OR EXCEED
ASHRAE 90.1B-1992 STANDARD AND ARE LISTED • One year limited warranty on all other component parts.
WITH THE CALIFORNIA ENERGY COMMISSION.
AMERICAN STANDARD WATER HEATERS • 1 800 900 9063 • FAX 909 392 7302
CE 01.3/09
COMMERCIAL ELECTRIC WATER HEATERS
SPECIFICATIONS & APPLICATION DATA
Top Hot Water Outlet
E
MODEL
GALLON Capacity
EXTERIOR Dimensions
A
B
C
D
E
F
F
D
C
CE-52-AS
52
CE-80-AS
80
CE-120-AS
119
24-3/4
6-1/2
46-9/16
44-3/8
51-1/2
54-1/4
4-1/2
28-1/4
6-1/2
46-9/16
48-17/32
56-1/4
58-5/8
4-1/2
30-1/4
6-1/2
46-9/16
59-7/8
68
70-3/4
4-1/2
1-1/2
1-1/2
1-1/2
271
366
483
Jacket Diameter
Floor To Cold Water Inlet
Floor To Top Of Control Box
Floor To PTR Valve
Height To Top Of Heater
Floor To Hot Water Outlet
Front Control Access Panel Depth
AMERICAN STANDARD reserves the right to make product
changes and/or improvements without notice.
DIMENSIONS [in inches]
CONNECTIONS
Water Connection
SHIPPING WEIGHT
B
[in pounds - approximate]
A
ELECTRICAL CHARACTERISTICS
Number Of Elements (Fused Models)*
208V
Kw Phase
Input 1 3
6
9
12
15
18
24
27
30
36
45
54
1
3
2
3
3
4
6
5
6
9
9
240V
Phase
1 3
3
3
3
3
3
6
6
6
6
9
9
1
3
2
3
3
4
6
5
6
9
9
277V
Phase
1 3
3
3
3
3
3
6
6
6
6
9
9
GPH
RECOVERY AT
VARIOUS
TEMPERATURE
RISES
2
3
2
3
3
4
6
5
6
9
9
Full Load Current Amperes
480V
Phase
1 3
NA
NA
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
1
3
2
3
3
4
6
5
6
9
9
208V
Phase
1 3
3
3
3
3
3
6
6
6
6
9
9
28.8
42.2[2]
57.6
72.1
86.5
115.4
129.8
144.2
173.0
216.3
259.6
240V
Phase
1 3
16.6
25.0
33.3
41.6
50.0
66.7
75.0
83.3
100.0
125.0
150.0
25.0
37.5[2]
50.0
62.5
75.0
100.0
112.5
125.0
150.0
187.5
225.0
277V
Phase
1 3
14.4
21.6
28.9
36.1
43.4
57.8
65.0
72.2
86.7
108.3
130.0
21.6
32.4[2]
43.3[2]
54.1
64.0
86.6
97.4
108.3
129.9
162.4
194.6
Kw
INPUT
40°
TEMPERATURE RISE FAHRENHEIT
50° 60° 70° 80° 90° 100° 120° 140°
6
9
12
15
18
24
27
30
36
45
54
62
93
124
155
186
248
279
310
372
465
558
50
74
99
124
149
199
223
248
298
372
447
41
62
83
103
124
164
186
207
248
310
372
35
53
71
89
106
142
160
177
213
266
319
31
47
62
78
93
124
140
155
186
233
279
28
41
55
69
83
110
124
138
165
207
248
25
37
50
62
74
99
112
124
149
186
223
21
31
41
52
62
83
93
103
124
155
186
18
27
35
44
53
71
80
89
106
133
160
N/.A
N/.A
N/.A
N/.A
N/.A
N/.A
N/.A
N/.A
N/.A
N/.A
N/.A
480V
Phase
1 3
12.5
18.7[2]
25.0
31.2
37.5
50.0
56.2
62.5
75.0
93.7
112.5
Units with amperage draw of 48 amps
or more require factory installed fusing
* If the number of elements on nonfused models is different, it is indicated
in parentheses() following the AMP
draw.
Thermostat settings range from 140°F
to 180°F. Optional 80°F to 140°F.
UL
®
“Living Up To A Higher Standard”
COMMERCIAL WATER HEATERS
2808 Metropolitan Place • Pomona • CA 91767
1 800 900 9063 • FAX 909 392 7302
7.2
10.8
14.4
18.0
21.6
28.9
32.5
36.1
43.3
54.1
65.0
Commercial Gas Water Heaters
MODEL: 75-76-AS
75 GALLON LIGHT DUTY STORAGE
76,100 BTU NAT GAS
76,100 BTU L.P. GAS
75-76-AS FEATURES
CG 001.3/09
75-76-AS SPECIFICATIONS AND APPLICATION DATA
Note: Recovery rate indicated on heater rating plate is based on 75% (76%) thermal efficiency according to CSA (ANSI, Z.21.10.3).
Manufacturer reserves the right to make product changes and/or improvements with or without notice.
Commercial gas water heater shall be AMERICAN STANDARD model _____________ having a storage
capacity of ________ gallons, operate on _____________ Gas, with a BTU input of _________________ and
a recovery rate of ________ gallons per hour at 100° F temperature rise. Water heater tank interior shall be
glass lined with Dura-Glas™, furnished with four anode rods and insulation shall be non-CFC foam of
R-16.7. Water heater shall be CSA certified.
“Living Up to A Higher Standard ”
Commercial Water Heaters
2808 Metropolitan Place • Pomona • CA 91767
1 (800) 900-9063 • (909) 392-0230 • Fax (909) 392-7302
Commercial Gas Water Heaters
MODEL: 100-83-AS
100 GALLON LIGHT DUTY STORAGE
83,000 BTU NAT GAS
83,000 BTU L.P. GAS
100-83-AS FEATURES
CG 002.3/09
Note: Recovery rate indicated on heater rating plate is based on 75% (76%) thermal efficiency according to CSA (ANSI, Z.21.10.3).
Manufacturer reserves the right to make product changes and/or improvements with or without notice.
Commercial gas water heater shall be AMERICAN STANDARD model _____________ having a storage
capacity of ________ gallons, operate on _____________ Gas, with a BTU input of _________________ and
a recovery rate of ________ gallons per hour at 100° F temperature rise. Water heater tank interior shall be
glass lined with Dura-Glas™, furnished with four anode rods and insulation shall be non-CFC foam of
R-16.7. Water heater shall be CSA certified.
“Living Up to A Higher Standard ”
Commercial Water Heaters
2808 Metropolitan Place • Pomona • CA 91767
1 (800) 900-9063 • (909) 392-0230 • Fax (909) 392-7302
Commercial Gas Water Heaters
MODEL: D-80-125-AS
80 GALLON HEAVY DUTY STORAGE
DIRECT SPARK IGNITION DAMPERED
125,000 BTU NAT GAS
125,000 BTU L.P. GAS
* FOR PROPANE (LP) GAS MODEL ADD SUFFIX “LP”, FOR SCAQMD LOW NOx MODEL ADD PREFIX “N”
Note: Recovery rate indicated on heater rating plate is based on 75% (76%) thermal efficiency according to CSA (ANSI, Z.21.10.3).
Manufacturer reserves the right to make product changes and/or improvements with or without notice.
Commercial gas water heater shall be AMERICAN STANDARD model _____________ having a storage
capacity of ________ gallons, operate on _____________ Gas, with a BTU input of _________________ and
a recovery rate of ________ gallons per hour at 100° F temperature rise. Water heater tank interior shall be
glass lined with Dura-Glas™, furnished with four anode rods and insulation shall be non-CFC foam of
R-8.3. Water heater shall be CSA certified.
“Living Up to A Higher Standard ”
Commercial Water Heaters
2808 Metropolitan Place • Pomona • CA 91767
1 (800) 900-9063 • (909) 392-0230 • Fax (909) 392-7302
Commercial Gas Water Heaters
MODEL: D-80-165-AS
80 GALLON HEAVY DUTY STORAGE
DIRECT SPARK IGNITION DAMPERED
165,000 BTU NAT GAS
165,000 BTU L.P. GAS
D-80-165-AS FEATURES
CG 003.3/09
D-80-165-AS SPECIFICATIONS AND APPLICATION DATA
ELECTRICAL
REQUIREMENTS
Note: Recovery rate indicated on heater rating plate is based on 75% (76%) thermal efficiency according to CSA (ANSI, Z.21.10.3).
Manufacturer reserves the right to make product changes and/or improvements with or without notice.
Commercial gas water heater shall be AMERICAN STANDARD model _____________ having a storage
capacity of ________ gallons, operate on _____________ Gas, with a BTU input of _________________ and
a recovery rate of ________ gallons per hour at 100° F temperature rise. Water heater tank interior shall be
glass lined with Dura-Glas™, furnished with four anode rods and insulation shall be non-CFC foam of
R-8.3. Water heater shall be CSA certified.
“Living Up to A Higher Standard ”
Commercial Water Heaters
2808 Metropolitan Place • Pomona • CA 91767
1 (800) 900-9063 • (909) 392-0230 • Fax (909) 392-7302
Commercial Gas Water Heaters
MODEL: D-80-180-AS
80 GALLON HEAVY DUTY STORAGE
DIRECT SPARK IGNITION DAMPERED
180,000 BTU NAT GAS
180,000 BTU L.P. GAS
3 9
Note: Recovery rate indicated on heater rating plate is based on 75% (76%) thermal efficiency according to CSA (ANSI, Z.21.10.3).
Manufacturer reserves the right to make product changes and/or improvements with or without notice.
Commercial gas water heater shall be AMERICAN STANDARD model _____________ having a storage
capacity of ________ gallons, operate on _____________ Gas, with a BTU input of _________________ and
a recovery rate of ________ gallons per hour at 100° F temperature rise. Water heater tank interior shall be
glass lined with Dura-Glas™, furnished with four anode rods and insulation shall be non-CFC foam of
R-8.3. Water heater shall be CSA certified.
“Living Up to A Higher Standard ”
Commercial Water Heaters
2808 Metropolitan Place • Pomona • CA 91767
1 (800) 900-9063 • (909) 392-0230 • Fax (909) 392-7302
Commercial Gas Water Heaters
MODEL: D-80-199-AS
80 GALLON HEAVY DUTY STORAGE
DIRECT SPARK IGNITION DAMPERED
199,900 BTU NAT GAS
199,900 BTU L.P. GAS
The American Standard Commercial Gas Model D-80-199-AS
is designed to deliver large quantities of hot water economically
through utilization of the most energy-saving techniques.
Customary applications include industrial buildings, motels,
hotels, schools, hospitals, restaurants, laundromats, car
washes and multi-family developments up to thirteen
single or ten double bath units.
D-80-199-AS FEATURES
• Heavy Gauge Steel Tank incorporating only five internal flue tubes resulting in fewer
critical welds to yield added years of trouble-free service.
• Inner tank glass-lined with Dura-Glas™ and fired at 1600° F for optimum protection
from the effects of corrosion.
• R-8.3 non-CFC foam insulated to save energy and reduce fuel costs by maximizing
heat retention.
• Four anode rods to ensure maximum tank life.
• Self-Cleaning turbulence inducing cold water inlet-tube engineered to diminish hard
water area sediment deposits.
• Full size hand-hole cleanout for eased tank inspection and/or removal of sediment
deposits.
• Electronic direct-spark ignition system saves fuel by eliminating the need for a
standby gas pilot.
• Automatic motorized flue damper reduces tank heat loss during standby periods for
lowest operating costs.
• Fully adjustable 24-volt controls provide temperature settings to 180° F. When
installed with a mixing valve, the D-80-199-AS can deliver 180° F sanitizing and 140°
F general purpose hot water simultaneously.
• Factory installed energy cut-off system and pressure/temperature relief valve.
• Top 11⁄2", 2" rear and 2" front water connections for universal replacements,
connection to circulating lines and eased multiple heater or storage tank installations.
THIS WATER HEATER MEETS THE REQUIREMENTS
OF ASHRAE 1992 STANDARD ADDENDUM
90.1b AND MEETS OR EXCEEDS THE THERMAL
EFFICIENCY AND STANDBY LOSS REQUIREMENTS
OF CALIFORNIA AND OTHER STATES
RECOGNIZING ASHRAE.
• AMERICAN STANDARD gas water heaters are certified at 300 PSI test pressure
and for 150 PSI working pressure. All tanks are hydrostatically tested at the factory.
• Tested and listed with CSA International in accordance with ANSI Z21.10.3
- CSA 4.3 for up to 180°F operation as an automatic storage and/or automatic circulating tank heater.
ASHRAE Standard 90.1 1989 addendum
90.lb
• Three year limited warranty on inner glass-lined tank and one year limited warranty
on all other component parts.
CG 005.3/09
D-80-199-AS SPECIFICATIONS AND APPLICATION DATA
SPECIFICATIONS
MODEL
NUMBER*
TANK
GALLONS
CAPACITY
BTU
INPUT
NAT
GAS
REC
GPH
100°
RISE
BTU
INPUT
L.P.
GAS
REC
GPH
100°
RISE
THERM
EFF
%
D-80-199-AS
80
199,900
194
199,900
194
80%
* FOR PROPANE (LP) GAS MODEL ADD SUFFIX “LP”, FOR SCAQMD LOW NOx MODEL ADD PREFIX “N”
DIMENSIONS SHOWN IN INCHES
EXTERIOR
DIMENSIONS
ELECTRICAL
REQUIREMENTS
A
Need 120 Volt 60
Cycle AC Power
Draws less than 5 AMPS
B
V
E
N
T
TOP REAR
PIPE
&
SIZE FRONT
WATER
CONN.
C
68 1/4 28 1/4 60 1/2
6
11/2
2
HGT.
TO
TOP
WATER
HGT.
HGT.
TOP
WATER TO REAR TO REAR
SPREAD & FRONT & FRONT
COLD
HOT
D
E
F
63 5/8
21 1/4
52
H
G
T
TO
GAS
I.P.S.
CONN.
WATER I.P.S.
CONNECTIONS
(TOP, REAR & FRONT)
G
H
G
T
T&P
O
P
E
N
I
N
G
T&P
O
P
E
N
I
N
G
S
I
Z
E
J
H
18 3/4 4 3/4
53 5/ 8
1/ 2
3/4
RECOVERY IN GALLONS PER HOUR AT VARIOUS TEMPERATURE RISES
MODEL
NUMBER
D-80-199-AS
TEMPERATURE RISE
GAS
TYPE
BTU
INPUT
40°
50°
60°
70°
80°
90°
100°
110°
120°
130°
140°
NAT
199,900
485
388
323
277
242
215
194
176
162
149
138
LP
199,900
485
388
323
277
242
215
194
176
162
149
138
MAXIMUM HOT WATER DELIVERABILITY AT VARIOUS TIME PERIODS
STORAGE
CAPACITY
U.S. GALLONS
ONE HOUR
RECOVERY
100° RISE
1ST HOUR
2 HOURS
3 HOURS
GPM
REC.
100° RISE
80
194
250
444
638
3.2
Note: Recovery rate indicated on heater rating plate is based on 75% (76%) thermal efficiency according to CSA (ANSI, Z.21.10.3).
Manufacturer reserves the right to make product changes and/or improvements with or without notice.
SAMPLE SPECIFICATION
Commercial gas water heater shall be AMERICAN STANDARD model _____________ having a storage
capacity of ________ gallons, operate on _____________ Gas, with a BTU input of _________________ and
a recovery rate of ________ gallons per hour at 100° F temperature rise. Water heater tank interior shall be
glass lined with Dura-Glas™, furnished with four anode rods and insulation shall be non-CFC foam of
R-8.3. Water heater shall be CSA certified.
Commercial Gas Water Heaters
MODEL: D-100-199-AS
100 GALLON HEAVY DUTY STORAGE
DIRECT SPARK IGNITION DAMPERED
199,900 BTU NAT GAS
199,900 BTU L.P. GAS
The American Standard Commercial Gas Model D-100-199-AS
is designed to deliver large quantities of hot water economically
through utilization of the most energy-saving techniques.
Customary applications include industrial buildings, motels,
hotels, schools, hospitals, restaurants, laundromats, car
washes and multi-family developments up to fourteen
single or eleven double bath units.
D-100-199-AS FEATURES
THIS WATER HEATER MEETS THE REQUIREMENTS
OF ASHRAE AND MEETS OR EXCEEDS THE
THERMAL EFFICIENCY REQUIREMENTS
OF CALIFORNIA AND OTHER STATES RECOGNIZING ASHRAE.
• Heavy Gauge Steel Tank incorporating fewer internal flue tubes resulting in fewer critical welds to yield added years of trouble-free service.
• Inner tank glass-lined with Dura-Glas™ and fired at 1600° F for optimum protection
from the effects of corrosion.
• R-8.3 non-CFC foam insulated to save energy and reduce fuel costs by maximizing
heat retention.
• Four anode rods to ensure maximum tank life.
• Self-Cleaning turbulence inducing cold water inlet-tube engineered to diminish hard
water area sediment deposits.
• Full size hand-hole cleanout for eased tank inspection and/or removal of sediment
deposits.
• Electronic direct-spark ignition system saves fuel by eliminating the need for a
standby gas pilot.
• Automatic motorized flue damper reduces tank heat loss dur ing standby periods for
lowest operating costs.
• Fully adjustable 24-volt controls provide temperature settings to 180° F. When
installed with a mixing valve, the D-100-199-AS can deliver 180° F sanitizing and
140° F general purpose hot water simultaneously.
• Factory installed energy cut-off system and pressure/temperature relief valve.
• Top 11⁄2", 2" rear and 2" front water connections for universal replacements,
connection to circulating lines and eased multiple heater or storage tank installations.
• AMERICAN STANDARD gas water heaters are certified at 300 PSI test pressure
and for 150 PSI working pressure. All tanks are hydrostatically tested at the factory.
• Tested and listed with CSA Inter national in accordance with ANSI Z21.10.3
- CSA 4.3 for up to 180° F operation as an automatic storage and/or automatic circulating tank heater. ASHRAE Standard 90.1 1999 addendum
90.1b. CSA certified to meet NSF/ANSI 5 Standards.
• Three year limited warranty on inner glass-lined tank and one year limited warranty
on all other component parts.
CG 006.3/09
D-100-199-AS SPECIFICATIONS AND APPLICATION DATA
SPECIFICATIONS
MODEL
NUMBER*
TANK
GALLONS
CAPACITY
BTU
INPUT
NAT
GAS
REC
GPH
100°
RISE
BTU
INPUT
L.P.
GAS
REC
GPH
100°
RISE
THERM
EFF
%
D-100-199-AS
100
199,900
194
199,900
194
80%
*For Propane (LP) Gas Model add suffix “LP”; For SCAQMD Low NOx Model add prefix “N”
DIMENSIONS SHOWN IN INCHES
EXTERIOR
DIMENSIONS
ELECTRICAL
REQUIREMENTS
A
Need 120 Volt 60
Cycle AC Power
Draws less than 5 AMPS
B
V
E
N
T
TOP REAR
PIPE
&
SIZE FRONT
WATER
CONN.
C
73 5/8 30 1/4 65 5/8
6
11/2
2
GAS
I.P.S.
CONN.
WATER I.P.S.
CONNECTIONS
(TOP, REAR & FRONT)
HGT.
TO
TOP
WATER
H
G
T
HGT.
HGT.
TOP
WATER TO REAR TO REAR
SPREAD & FRONT & FRONT
COLD
HOT
H
G
T
TO
T&P
O
P
E
N
I
N
G
S
I
Z
E
D
E
F
G
H
67 5/8
23 5/8
57 1/2
20
4 3/4
T&P
O
P
E
N
I
N
G
J
58 7/ 8
3/ 4
3/4
RECOVERY IN GALLONS PER HOUR AT VARIOUS TEMPERATURE RISES
MODEL
NUMBER
D-100-199-AS
TEMPERATURE RISE
GAS
TYPE
BTU
INPUT
40°
50°
60°
70°
80°
90°
100°
110°
120°
130°
140°
NAT
199,900
485
388
323
277
242
215
194
176
162
149
138
LP
199,900
485
388
323
277
242
215
194
176
162
149
138
MAXIMUM HOT WATER DELIVERABILITY AT VARIOUS TIME PERIODS
STORAGE
CAPACITY
U.S. GALLONS
ONE HOUR
RECOVERY
100° RISE
1ST HOUR
2 HOURS
3 HOURS
GPM
REC.
100° RISE
100
194
264
458
652
3.2
Note: Recovery rate indicated on heater rating plate is based on 75% (76%) thermal efficiency according to CSA (ANSI, Z.21.10.3).
Manufacterer reserves the right to make product changes and/or improvements with or without notice.
SAMPLE SPECIFICATION
Commercial gas water heater shall be AMERICAN STANDARD model _____________ having a storage
capacity of ________ gallons, operate on _____________ Gas, with a BTU input of _________________ and
a recovery rate of ________ gallons per hour at 100° F temperature rise. Water heater tank interior shall be
glass lined with Dura-Glas™, furnished with four anode rods and insulation shall be non-CFC foam of
R-8.3. Water heater shall be CSA certified.
“Living Up to A Higher Standard ”
Commercial Water Heaters
2808 Metropolitan Place • Pomona • CA 91767
1 (800) 900-9063 • (909) 392-0230 • Fax (909) 392-7302
Commercial Gas Water Heaters
MODEL: D-100T-199-AS (TALL)
100 GALLON HEAVY DUTY STORAGE
DIRECT SPARK IGNITION DAMPERED
199,900 BTU NAT GAS
199,900 BTU L.P. GAS
The American Standard Commercial Gas Model D-100T-199-AS
is designed to deliver large quantities of hot w ater economically
through utilization of the most energy-sa ving techniques.
Customary applications include industrial buildings, motels,
hotels, schools, hospitals, restaurants, laundromats, car
washes and multi-family developments up to fourteen
single or eleven double bath units.
D-100T-199-AS FEATURES
THIS WATER HEATER MEETS THE REQUIREMENTS
OF ASHRAE AND MEETS OR EXCEEDS THE
THERMAL EFFICIENCY REQUIREMENTS
OF CALIFORNIA AND OTHER STATES RECOGNIZING ASHRAE.
• Heavy Gauge Steel Tank incorporating fewer internal flue tubes resulting in fewer critical welds to yield added years of trouble-free service.
• Inner tank glass-lined with Dura-Glas™ and fired at 1600° F for optimum protection
from the effects of corrosion.
• R-8.3 non-CFC foam insulated to save energy and reduce fuel costs by maximizing
heat retention.
• Four anode rods to ensure maximum tank life.
• Self-Cleaning turbulence inducing cold water inlet-tube engineered to diminish hard
water area sediment deposits.
• Full size hand-hole cleanout for eased tank inspection and/or removal of sediment
deposits.
• Electronic direct-spark ignition system saves fuel by eliminating the need for a
standby gas pilot.
• Automatic motorized flue damper reduces tank heat loss dur ing standby periods for
lowest operating costs.
• Fully adjustable 24-volt controls provide temperature settings to 180° F. When
installed with a mixing valve, the D-100T-199-AS can deliver 180° F sanitizing and
140° F general purpose hot water simultaneously.
• Factory installed energy cut-off system and pressure/temper ature relief valve.
• Top 1 1⁄2", 2" rear and 2" front water connections for universal replacements,
connection to circulating lines and eased m ultiple heater or storage tank installations.
• AMERICAN STANDARD gas water heaters are certified at 300 PSI test pressure
and for 150 PSI working pressure. All tanks are hydrostatically tested at the factory.
• Tested and listed with CSA Inter national in accordance with ANSI Z21.10.3
- CSA 4.3 for up to 180° F operation as an automatic storage and/or automatic circulating tank heater. ASHRAE Standard 90.1 1999 addendum
90.1b. CSA certified to meet NSF/ANSI 5 Standards.
• Three year limited warranty on inner glass-lined tank and one y ear limited warranty
on all other component parts.
CG 007.2/10
D-100T-199-AS (TALL) SPECIFICATIONS & APPLICATION DATA
SPECIFICATIONS
MODEL
NUMBER
TANK
GALLONS
CAPACITY
BTU
INPUT
NAT
GAS
REC
GPH
100°
RISE
BTU
INPUT
L.P.
GAS
REC
GPH
100°
RISE
THERM
EFF
%
D -100T-199 - AS
100
199,900
194
199,900
194
80%
*For Propane (LP) Gas Model add suffix “LP”; For SCAQMD Low NOx Model add prefix “N”
DIMENSIONS SHOWN IN INCHES
EXTERIOR
DIMENSIONS
ELECTRICAL
REQUIREMENTS
A
Need 120 Volt 60
Cycle AC Power
Draws less than 5 AMPS
B
V
E
N
T
TOP REAR
PIPE
&
SIZE FRONT
WATER
CONN.
C
781/ 4 28 1/4 70 1/ 2
6
11/2
2
GAS
I.P.S.
CONN.
WATER I.P.S.
CONNECTIONS
(TOP, REAR & FRONT)
HGT.
TO
TOP
WATER
HGT.
HGT.
TOP
WATER TO REAR TO REAR
SPREAD & FRONT & FRONT
COLD
HOT
D
E
F
73 5/8
211/4
62
G
H
G
T
H
G
T
TO
T&P
O
P
E
N
I
N
G
S
I
Z
E
T&P
O
P
E
N
I
N
G
J
H
18 3/4 4 3/4 3/4 63 5/ 8 3/4
RECOVERY IN GALLONS PER HOUR AT VARIOUS TEMPERATURE RISES
MODEL
NUMBER
D-100T-199-AS
TEMPERATURE RISE
GAS
TYPE
BTU
INPUT
40°
50°
60°
70°
80°
90°
100°
110°
120°
130°
140°
NAT
199,900
485
388
323
277
242
215
194
176
162
149
138
LP
199,900
485
388
323
277
242
215
194
176
162
149
138
MAXIMUM HOT WATER DELIVERABILITY AT VARIOUS TIME PERIODS
STORAGE
CAPACITY
U.S. GALLONS
ONE HOUR
RECOVERY
100° RISE
1ST HOUR
2 HOURS
3 HOURS
GPM
REC.
100° RISE
100
194
264
458
652
3.2
Note: Recovery rate indicated on heater rating plate is based on 75% (76%) thermal efficiency according to CSA (ANSI, Z.21.10.3).
Manufacturer reserves the right to make product changes and/or improvements with or without notice.
SAMPLE SPECIFICATION
Commercial gas water heater shall be AMERICAN STANDARD model _____________ having a storage
capacity of ________ gallons, operate on _____________ Gas, with a BTU input of _________________ and
a recovery rate of ________ gallons per hour at 100° F temperature rise. Water heater tank interior shall be
glass lined with Dura-Glas™, furnished with four anode rods and insulation shall be non-CFC foam of
R-8.3. Water heater shall be CSA certified.
“Living Up to A Higher Standard ”
Commercial Water Heaters
2808 Metropolitan Place • Pomona • CA 91767
1 (800) 900-9063 • (909) 392-0230 • Fax (909) 392-7302
Commercial Gas Water Heaters
MODEL: D-100-250-AS
100 GALLON HEAVY DUTY STORAGE
DIRECT SPARK IGNITION DAMPERED
250,000 BTU NAT GAS
250,000 BTU L.P. GAS
The American Standard Commercial Gas Model D-100-250-AS
is designed to deliver large quantities of hot water economically
through utilization of the most energy-saving techniques.
Customary applications include industrial buildings, motels,
hotels, schools, hospitals, restaurants, laundromats, car
washes and multi-family developments up to sixteen single
or twelve double bath units.
D-100-250-AS FEATURES
• Heavy Gauge Steel Tank incorporating only seven internal flue tubes resulting
in fewer critical welds to yield added years of service.
• ASME Construction Model available.
• Inner tank glass-lined with Dura-Glas™ and fired at 1600° F for optimum
protection from the effects of corrosion.
• R-8.3 non-CFC foam insulated to save energy and reduce fuel costs by
maximizing heat retention.
• Four anode rods to ensure maximum tank life.
• Self-Cleaning turbulence inducing cold water inlet-tube engineered to diminish
hard water area sediment deposits.
• Full size hand-hole cleanout for eased tank inspection and/or removal of sediment
deposits.
• Electronic direct-spark ignition system saves fuel by eliminating the need for a
standby gas pilot.
• Automatic motorized flue damper reduces tank heat loss during standby periods
for lowest operating costs.
• Fully adjustable 24-volt controls provide temperature settings to 180° F. When
installed with a mixing valve, the D-100-250-AS can deliver 180° F sanitizing and
140° F general purpose hot water simultaneously.
• Factory installed energy cut-off system and pressure/temperature valve.
THIS WATER HEATER MEETS THE REQUIREMENTS
OF ASHRAE 90.1-1999
AND MEETS OR EXCEEDS
THE THERMAL EFFICIENCY
AND STANDBY LOSS REQUIREMENTS
OF CALIFORNIA AND OTHER STATES
RECOGNIZING ASHRAE.
• Top 1 1/2", 2" rear and 2" front water connections for universal replacements,
connection to circulating lines and eased multiple heater or storage tank
installations.
• AMERICAN STANDARD gas water heaters are certified at 300 PSI test pressure
and for 150 PSI working pressure. CSA certified to meet NSF/ANSI 5 Standards.
• Tested and listed with CSA International in accordance with ANSI Z21.10.3-CSA
4.3 for up to 180° F operation as an automatic storage and/or automatic circulating tank heater. Meets ASHRAE Standard 90.1-1999.
• Three year limited warranty on inner glass-lined tank and one year limited
warranty on all other component parts.
CG 008.3/09
D-100-250-AS SPECIFICATIONS AND APPLICATION DATA
SPECIFICATIONS
MODEL
NUMBER*
TANK
GALLONS
CAPACITY
BTU
INPUT
NAT
GAS
REC
GPH
100°
RISE
BTU
INPUT
L.P.
GAS
REC
GPH
100°
RISE
THERM
EFF
%
D-100-250-AS
100
250,000
242
250,000
242
80%
*For ASME Model Specify D-100-250-ASME; for Propane (LP) Gas Model add suffix “LP”;
for SCAQMD Low NOx Model add prefix “N”
DIMENSIONS SHOWN IN INCHES
EXTERIOR
DIMENSIONS
ELECTRICAL
REQUIREMENTS
A
Need 120 Volt 60
Cycle AC Power
Draws less than 5 AMPS
B
V
E
N
T
TOP
PIPE
SIZE
REAR
&
FRONT
WATER
CONN.
C
73 5/8 30 1/4 65 5/8
6
11/2
2
HGT.
TO
TOP
WATER
H
G
T
TO
GAS
I.P.S.
CONN.
WATER I.P.S.
CONNECTIONS
(TOP, REAR & FRONT)
H
G
T
HGT.
HGT.
TOP
WATER TO REAR TO REAR
SPREAD & FRONT & FRONT
COLD
HOT
TAP
O
P
E
N
I
N
G
S
I
Z
E
D
E
F
G
H
67 5/8
23 5/8
571/2
20
4 3/4
TAP
O
P
E
N
I
N
G
J
3/4
58 7/8
1
RECOVERY IN GALLONS PER HOUR AT VARIOUS TEMPERATURE RISES
MODEL
NUMBER
D-100-250-AS
TEMPERATURE RISE
GAS
TYPE
BTU
INPUT
40°
50°
60°
70°
80°
90°
100°
110°
120°
130°
140°
NAT
250,000
606
485
404
346
303
269
242
220
202
186
173
LP
250,000
606
485
404
346
303
269
242
220
202
186
173
MAXIMUM HOT WATER DELIVERABILITY AT VARIOUS TIME PERIODS
STORAGE
CAPACITY
U.S. GALLONS
ONE HOUR
RECOVERY
100° RISE
1ST HOUR
2 HOURS
3 HOURS
GPM
REC.
100° RISE
100
242
312
554
796
4
Note: Recovery rate indicated on heater rating plate is based on 75% (76%) thermal efficiency according to CSA (ANSI, Z.21.10.3).
Manufacturer reserves the right to make product changes and/or improvements with or without notice.
SAMPLE SPECIFICATION
Commercial gas water heater shall be AMERICAN STANDARD model _____________ having a storage
capacity of ________ gallons, operate on _____________ Gas, with a BTU input of _________________ and
a recovery rate of ________ gallons per hour at 100° F temperature rise. Water heater tank interior shall be
glass lined with Dura-Glas™, furnished with four anode rods and insulation shall be non-CFC foam of
R-8.3. Water heater shall be CSA certified.
Commercial Gas Water Heaters
MODEL: D-100-270-AS
100 GALLON HEAVY DUTY STORAGE
DIRECT SPARK IGNITION DAMPERED
270,000 BTU NAT GAS
270,000 BTU L.P. GAS
The American Standard Commercial Gas Model D-100-270-AS
is designed to deliver large quantities of hot water economically
through utilization of the most energy-saving techniques.
Customary applications include industrial buildings, motels,
hotels, schools, hospitals, restaurants, laundromats, car
washes and multi-family developments up to eighteen single
or thirteen double bath units.
D-100-270-AS FEATURES
• Heavy Gauge Steel Tank incorporating only seven internal flue tubes resulting
in fewer critical welds to yield added years of trouble-free service.
• ASME Construction Model available.
• Inner tank glass-lined with Dura-Glas™ and fired at 1600° F for optimum
protection from the effects of corrosion.
• R-8.3 non-CFC foam insulated to save energy and reduce fuel costs by
maximizing heat retention.
• Four anode rods to ensure maximum tank life.
• Self-Cleaning turbulence inducing cold water inlet-tube engineered to diminsh
hard water area sediment deposits.
• Full size hand-hole cleanout for eased tank inspection and/or removal of
sediment deposits.
• Electronic direct-spark ignition system saves fuel by eliminating the need for a
standby gas pilot.
• Automatic motorized flue damper reduces tank heat loss during standby
periods for lowest operating costs.
• Fully adjustable 24-volt controls provide temperature settings to 180° F. When
installed with a mixing valve, the D-100-270-AS can deliver 180° F sanitizing
and 140° F general purpose hot water simultaneously.
THIS WATER HEATER MEETS THE REQUIREMENTS
OF ASHRAE 90.1-1999
AND MEETS OR EXCEEDS
THE THERMAL EFFICIENCY
AND STANDBY LOSS REQUIREMENTS
OF CALIFORNIA AND OTHER STATES
RECOGNIZING ASHRAE.
• Factory installed energy cut-off system and pressure/temperature valve.
• Top 1 1/2", 2" rear and 2" front water connections for universal replacements,
connection to circulating lines and eased multiple heater or storage tank
installations. CSA certified to meet NSF/ANSI 5 Standards.
• AMERICAN STANDARD gas water heaters are certified at 300 PSI test
pressure and for 150 PSI working pressure.
• Tested and listed with CSA International in accordance with ANZI Z21.10.3 CSA 4.3 for up to 180° F operation as an automatic storage and/or automatic
circulating tank heater, meets ASHRAE 90.1-1999.
• Three year limited warranty on inner glass-lined tank and one year limited
warranty on all other component parts.
CG 009.3/ 09
D-100-270-AS SPECIFICATIONS AND APPLICATION DATA
SPECIFICATIONS
MODEL
NUMBER
TANK
GALLONS
CAPACITY
BTU
INPUT
NAT
GAS
REC
GPH
100°
RISE
BTU
INPUT
L.P.
GAS
REC
GPH
100°
RISE
THERM
EFF
%
D-100-270-AS
100
270,000
262
270,000
262
80%
*For ASME Model: Specify D-100-270-ASME; For Propane (LP) Gas Model add suffix
“LP”; For SCAQMD Low NOx Model add prefix “N”.
DIMENSIONS SHOWN IN INCHES
EXTERIOR
DIMENSIONS
V
E
N
T
TOP
PIPE
SIZE
REAR
&
FRONT
WATER
CONN.
ELECTRICAL
REQUIREMENTS
Need 120 Volt 60
Cycle AC Power
Draws less than 5 AMPS
B
A
C
73 5/8 30 1/4 65 5/8
6
2
11/2
HGT.
TO
TOP
WATER
H
G
T
TO
T&P
O
P
E
N
I
N
G
GAS
I.P.S.
CONN.
WATER I.P.S.
CONNECTIONS
(TOP, REAR & FRONT)
H
G
T
HGT.
HGT.
TOP
WATER TO REAR TO REAR
SPREAD & FRONT & FRONT
COLD
HOT
S
I
Z
E
D
E
F
G
H
67 5/8
23 5/ 8
57 1/ 2
20
4 3/4
T&P
O
P
E
N
I
N
G
J
3/4
58 7/8
1
RECOVERY IN GALLONS PER HOUR AT VARIOUS TEMPERATURE RISES
MODEL
NUMBER
D-100-270-AS
TEMPERATURE RISE
GAS
TYPE
BTU
INPUT
40°
50°
60°
70°
80°
90°
100°
110°
120°
130°
140°
NAT
270,000
655
524
436
374
327
291
262
238
218
201
187
LP
270,000
655
524
436
374
327
291
262
238
218
201
187
MAXIMUM HOT WATER DELIVERABILITY AT VARIOUS TIME PERIODS
STORAGE
CAPACITY
U.S. GALLONS
ONE HOUR
RECOVERY
100° RISE
1ST HOUR
2 HOURS
3 HOURS
GPM
REC.
100° RISE
100
262
332
594
856
4.4
Note: Recovery rate indicated on heater rating plate is based on 75% (76%) thermal efficiency according to CSA (ANSI, Z.21.10.3).
Manufacturer reserves the right to make product changes and/or improvements with or without notice.
SAMPLE SPECIFICATION
Commercial gas water heater shall be AMERICAN STANDARD model _____________ having a storage
capacity of ________ gallons, operate on _____________ Gas, with a BTU input of _________________ and
a recovery rate of ________ gallons per hour at 100° F temperature rise. Water heater tank interior shall be
glass lined with Dura-Glas™, furnished with four anode rods and insulation shall be non-CFC foam of
R-8.3. Water heater shall be CSA certified.
Commercial Gas Water Heaters
MODEL: D-100-300-AS
100 GALLON HEAVY DUTY STORAGE
DIRECT SPARK IGNITION DAMPERED
300,000 BTU NAT GAS
300,000 BTU L.P. GAS
The American Standard Commercial Gas Model D-100-300-AS
is designed to deliver large quantities of hot water economically
through utilization of the most energy-saving techniques.
Customary applications include industrial buildings, motels,
hotels, schools, hospitals, restaurants, laundromats, car
washes and multi-family developments up to nineteen single
or fourteen double bath units.
D-100-300-AS FEATURES
• Heavy Gauge Steel Tank incorporating only twelve internal flue tubes resulting
in fewer critical welds to yield added years of trouble-free service.
• ASME Construction Model available.
• Inner tank glass-lined with Dura-Glas™ and fired at 1600° F for optimum
protection from the effects of corrosion.
• R-8.3 non-CFC foam insulated to save energy and reduce fuel costs by
maximizing heat retention.
• Four anode rods to ensure maximum tank life.
• Self-Cleaning turbulence inducing cold water inlet-tube engineered to diminsh
hard water area sediment deposits.
• Full size hand-hole cleanout for eased tank inspection and/or removal of
sediment deposits.
• Electronic direct-spark ignition system saves fuel by eliminating the need for a
standby gas pilot.
• Automatic motorized flue damper reduces tank heat loss during standby
periods for lowest operating costs.
• Fully adjustable 24-volt controls provide temperature settings to 180° F. When
installed with a mixing valve, the D-100-300-AS can deliver 180° F sanitizing
and 140° F general purpose hot water simultaneously.
THIS WATER HEATER MEETS THE REQUIREMENTS
OF ASHRAE 90.1-1999
AND MEETS OR EXCEEDS
THE THERMAL EFFICIENCY
AND STANDBY LOSS REQUIREMENTS
OF CALIFORNIA AND OTHER STATES
RECOGNIZING ASHRAE.
• Factory installed energy cut-off system and pressure/temperature valve.
• Top 1 1/2", 2" rear and 2" front water connections for universal replacements,
connection to circulating lines and eased multiple heater or storage tank
installations. CSA certified to meet NSF/ANSI 5 Standards.
• AMERICAN STANDARD gas water heaters are certified at 300 PSI test
pressure and for 150 PSI working pressure.
• Tested and listed with CSA International in accordance with ANZI Z21.10.3 CSA 4.3 for up to 180° F operation as an automatic storage and/or automatic
circulating tank heater, meets ASHRAE 90.1-1999.
• Three year limited warranty on inner glass-lined tank and one year limited
warranty on all other component parts.
CG 010.3/ 09
D-100-300-AS SPECIFICATIONS AND APPLICATION DATA
SPECIFICATIONS
MODEL
NUMBER
TANK
GALLONS
CAPACITY
BTU
INPUT
NAT
GAS
REC
GPH
100°
RISE
BTU
INPUT
L.P.
GAS
REC
GPH
100°
RISE
THERM
EFF
%
D-100-300-AS
100
300,000
291
300,000
291
80%
*For ASME Model: Specify D-100-300-ASME; For Propane (LP) Gas Model add suffix
“LP”; For SCAQMD Low NOx Model add prefix “N”.
DIMENSIONS SHOWN IN INCHES
EXTERIOR
DIMENSIONS
V
E
N
T
TOP
PIPE
SIZE
REAR
&
FRONT
WATER
CONN.
ELECTRICAL
REQUIREMENTS
Need 120 Volt 60
Cycle AC Power
Draws less than 5 AMPS
B
A
C
73 5/8 30 1/4 65 5/8
7
2
11/2
HGT.
TO
TOP
WATER
H
G
T
TO
T&P
O
P
E
N
I
N
G
GAS
I.P.S.
CONN.
WATER I.P.S.
CONNECTIONS
(TOP, REAR & FRONT)
H
G
T
HGT.
HGT.
TOP
WATER TO REAR TO REAR
SPREAD & FRONT & FRONT
COLD
HOT
S
I
Z
E
D
E
F
G
H
67 5/8
23 5/ 8
57 1/ 2
20
4 3/4
T&P
O
P
E
N
I
N
G
J
3/4
58 7/8
1
RECOVERY IN GALLONS PER HOUR AT VARIOUS TEMPERATURE RISES
MODEL
NUMBER
D-100-300-AS
TEMPERATURE RISE
GAS
TYPE
BTU
INPUT
40°
50°
60°
70°
80°
90°
100°
110°
120°
130°
140°
NAT
300,000
727
582
485
416
364
323
291
265
242
224
208
LP
300,000
727
582
485
416
364
323
291
265
242
224
208
MAXIMUM HOT WATER DELIVERABILITY AT VARIOUS TIME PERIODS
STORAGE
CAPACITY
U.S. GALLONS
ONE HOUR
RECOVERY
100° RISE
1ST HOUR
2 HOURS
3 HOURS
GPM
REC.
100° RISE
100
291
361
652
943
4.9
Note: Recovery rate indicated on heater rating plate is based on 75% (76%) thermal efficiency according to CSA (ANSI, Z.21.10.3).
Manufacturer reserves the right to make product changes and/or improvements with or without notice.
SAMPLE SPECIFICATION
Commercial gas water heater shall be AMERICAN STANDARD model _____________ having a storage
capacity of ________ gallons, operate on _____________ Gas, with a BTU input of _________________ and
a recovery rate of ________ gallons per hour at 100° F temperature rise. Water heater tank interior shall be
glass lined with Dura-Glas™, furnished with four anode rods and insulation shall be non-CFC foam of
R-8.3. Water heater shall be CSA certified.
Commercial Gas Water Heaters
MODEL: D-75-365-AS
75 GALLON HEAVY DUTY INSTANTANEOUS
DIRECT SPARK IGNITION DAMPERED
365,000 BTU NAT GAS
365,000 BTU L.P. GAS
The American Standard Commercial Gas Model D-75-365-AS
is designed to deliver large quantities of hot water economically
through utilization of the most energy–saving techniques.
Customary applications include industrial buildings, motels,
hotels, schools, hospitals, restaurants, laundromats, car
washes and multi-family developments up
to 21 single or 15 double bath units.
D-75-365-AS FEATURES
‡ +HDY\*DXJH6WHHO7DQNXWLOL]HVRQO\WZHOYHLQWHUQDOIOXHWXEHVUHVXOWLQJLQ
IHZHUFULWLFDOZHOGVWR\LHOGDGGHG\HDUVRI WURXEOH±IUHHVHUYLFH
‡ $60(&RQVWUXFWLRQ0RGHODYDLODEOH
‡ ,QQHUWDQNJODVV±OLQHGZLWK'XUD±*ODVŒ DQGILUHGDWƒ )IRURSWLPXP
SURWHFWLRQIURPWKHHIIHFWVRIFRUURVLRQ
‡ 5QRQ&)&IRDPLQVXODWHGWRVDYHHQHUJ\DQGUHGXFHIXHOFRVWVE \
PD[LPL]LQJKHDWUHWHQWLRQ
‡ )RXUDQRGHURGVWRSURORQJWDQNOLIH
‡ 6HOI&OHDQLQJWXUEXOHQFHLQGXFLQJFROGZDWHULQOHWWXEHHQJLQHHUHGWRGLPLQLVK
KDUGZDWHUDUHDVHGLPHQWGHSRVLWV
‡ )XOOVL]HKDQG±KROHFOHDQRXWIRUHDVHGWDQNLQVSHFWLRQDQGRUUHPRYDORI
VHGLPHQWGHSRVLWV
‡ (OHFWURQLFGLUHFW±VSDUNLJQLWLRQV\VWHPVDYHVIXHOE\HOLPLQDWLQJWKHQHHGIRUD
VWDQGE\JDVSLORW
‡ $XWRPDWLFPRWRUL]HGIOXHGDPSHUUHGXFHVWDQNKHDWORVVGXU LQJVWDQGE\SHULRGV
IRUORZHVWRSHUDWLQJFRVWV
‡ )XOO\DGMXVWDEOH±YROWFRQWUROVSURYLGHWHPSHUDWXUHVHWWLQJVWRƒ ) :KHQ
LQVWDOOHGZLWKDPL[LQJYDOYHWKH'$6FDQGHOLYHUƒ )VDQLWL]LQJDQG
ƒ )JHQHUDOSXUSRVHKRWZDWHUVLPXOWDQHRXVO\
‡ )DFWRU\LQVWDOOHGHQHUJ\FXWRIIV\VWHPDQGSUHVVXUH WHPSHUDWXUHYDOYH
7+,6:$7(5+($7(50((767+(5(48,5(0(176
2)$6+5$(67$1'$5'$''(1'80
E$1'0((7625(;&(('67+(7+(50$/
()),&,(1&<$1'67$1'%</2665(48,5(0(176
2)&$/,)251,$$1'27+(567$7(6
5(&2*1,=,1*$6+5$(
‡ 7ZRLQFK UHDUDQGIURQWZDWHUFRQQHFWLRQVIRUVLPSOLILHGUHSODFHPHQWRIVLPLODU
XQLWVFRQQHFWLRQWRFLUFXODWLQJOLQHVDQGHDVHGP XOWLSOHKHDWHURUVWRUDJHWDQN
LQVWDOODWLRQV&6$FHUWLILHGWRPHHW16)$16,6WDQGDUGV
‡ $0(5,&$167$1'$5'JDVZDWHUKHDWHUVDUHFHUWLILHGDW36,WHVWSUHVVXUH
DQGIRU36,ZRUNLQJSUHVVXUH $OOWDQNVDUHK\GURVWDWLFDOO\WHVWHGDWWKHIDFWRU\
‡ 7HVWHGDQGOLVWHGZLWK&6$,QWHU QDWLRQDOLQDFFRUGDQFHZLWK$16,=
&6$IRUXSWRƒ )RSHUDWLRQDVDQLQVWDQWDQHRXVDQGRUDXWRPDWLFFLUFX
ODWLQJWDQNKHDWHU0HHWV $6+5$(E
‡ 7KUHH\HDUOLPLWHGZDUUDQW\RQLQQHUJODVV±OLQHGWDQNDQGRQH\ HDUOLPLWHG
ZDUUDQW\RQDOORWKHUFRPSRQHQWSDU WV
CG 009B.3/09
D-75-365-AS SPECIFICATIONS AND APPLICATION DATA
SPECIFICATIONS
MODEL
NUMBER*
TANK
GALLONS
CAPACITY
BTU
INPUT
NAT
GAS
REC
GPH
100°
RISE
BTU
INPUT
L.P.
GAS
REC
GPH
100°
RISE
THERM
EFF
%
D-75-365-AS
75
365,000
358
365,000
358
81%
*For ASME Model: Specify D-75-365-ASME; For Propane (LP) Gas Model add suffix “LP”;
For SCAQMD Low NOx Model add prefix “N”
DIMENSIONS SHOWN IN INCHES
EXTERIOR
DIMENSIONS
ELECTRICAL
REQUIREMENTS
A
Need 120 Volt 60
Cycle AC Power
Draws less than 5 AMPS
B
753/ 4 301/4
C
661/ 4
8
2
H
G
T
TO
T&P
O
P
E
N
I
N
G
GAS
I.P.S.
CONN.
WATER I.P.S.
CONNECTIONS
(REAR & FRONT)
REAR
&
FRONT
WATER
CONN.
SIZE
V
E
N
T
HEIGHT
TO REAR
& FRONT
HOT
HEIGHT
TO REAR
& FRONT
COLD
H
G
T
F
G
H
57
19 1/ 4
4 3/ 4
S
I
Z
E
T&P
O
P
E
N
I
N
G
J
58 1/ 4
3/ 4
1
RECOVERY IN GALLONS PER HOUR AT VARIOUS TEMPERATURE RISES
MODEL
NUMBER
D-75-365-AS
TEMPERATURE RISE
GAS
TYPE
BTU
INPUT
40°
50°
60°
70°
80°
90°
100°
110°
120°
130°
140°
NAT
365,000
895
716
597
511
448
398
358
326
298
276
256
LP
365,000
895
716
597
511
448
398
358
326
298
276
256
MAXIMUM HOT WATER DELIVERABILITY AT VARIOUS TIME PERIODS
STORAGE
CAPACITY
U.S. GALLONS
ONE HOUR
RECOVERY
100° RISE
1ST HOUR
2 HOURS
3 HOURS
GPM
REC.
100° RISE
75
358
411
769
1,179
5.9
Note: Recovery rate indicated on heater rating plate is based on 75% (76%) thermal efficiency according to CSA (ANSI, Z.21.10.3).
Manufacturer reserves the right to make product changes and/or improvements with or without notice.
SAMPLE SPECIFICATION
Commercial gas water heater shall be AMERICAN STANDARD model _____________ having a storage
capacity of ________ gallons, operate on _____________ Gas, with a BTU input of _________________ and
a recovery rate of ________ gallons per hour at 100° F temperature rise. Water heater tank interior shall be
glass lined with Dura-Glas™, furnished with four anode rods and insulation shall be non-CFC foam of
R-8.3. Water heater shall be CSA certified.
“Living Up to A Higher Standard ”
COMMERCIAL WATER HEATERS
2808 Metropolitan Place, Pomona, CA 91767
1(800)900-9063 • (909)392-0230 • Fax (909)392-7302
Commercial Gas Water Heaters
MODEL: D-75-399-AS
75 GALLON HEAVY DUTY INSTANTANEOUS
DIRECT SPARK IGNITION DAMPERED
399,900 BTU NAT GAS
399,900 BTU L.P. GAS
The American Standard Commercial Gas Model D-75-399-AS
is designed to deliver large quantities of hot water economically
through utilization of the most energy–saving techniques.
Customary applications include industrial buildings, motels,
hotels, schools, hospitals, restaurants, laundromats, car
washes and multi-family developments up
to 24 single or 17 double bath units.
D-75-399-AS FEATURES
THIS WATER HEATER MEETS THE REQUIREMENTS
OF ASHRAE 1992 STANDARD ADDENDUM
90.1b AND MEETS OR EXCEEDS THE THERMAL
EFFICIENCY AND STANDBY LOSS REQUIREMENTS
OF CALIFORNIA AND OTHER STATES
RECOGNIZING ASHRAE.
• Heavy Gauge Steel Tank utilizes only twelve internal flue tubes resulting in fewer
critical welds to yield added years of trouble–free service.
• ASME Construction Model available.
• Inner tank glass–lined with Dura–Glas™ and fired at 1600° F for optimum
protection from the effects of corrosion.
• R-8.3 non-CFC foam insulated to save energy and reduce fuel costs by
maximizing heat retention.
• Four anode rods to prolong tank life.
• Self-Cleaning turbulence inducing cold water inlet-tube engineered to diminish
hard water area sediment deposits.
• Full size hand–hole cleanout for eased tank inspection and/or removal of
sediment deposits.
• Electronic direct–spark ignition system saves fuel by eliminating the need for a
standby gas pilot.
• Automatic motorized flue damper reduces tank heat loss during standby periods
for lowest operating costs.
• Fully adjustable 24–volt controls provide temperature settings to 180° F. When
installed with a mixing valve, the D-75-399-AS can deliver 180° F sanitizing and
140° F general purpose hot water simultaneously.
• Factory installed energy cut-off system and pressure/temperature relief valve.
• Two inch rear and front water connections for simplified replacement of similar
units, connection to circulating lines and eased multiple heater or storage tank
installations. CSA certified to meet NSF/ANSI 5 Standards.
• AMERICAN STANDARD gas water heaters are certified at 300 PSI test
pressure and for 150 PSI working pressure. All tanks are hydrostatically tested
at the factory.
• Tested and listed with CSA International in accordance with ANSI Z21.10.3 CSA 4.3 for up to 180° F operation as an instantaneous and/or automatic
circulating tank heater. Meets ASHRAE 1992 90.1b.
• Three year limited warranty on inner glass–lined tank and one year limited
warranty on all other component parts.
CG 010.3/09
D-75-399-AS SPECIFICATIONS AND APPLICATION DATA
SPECIFICATIONS
MODEL
NUMBER*
TANK
GALLONS
CAPACITY
BTU
INPUT
NAT
GAS
REC
GPH
100°
RISE
BTU
INPUT
L.P.
GAS
REC
GPH
100°
RISE
THERM
EFF
%
D-75-399-AS
75
399,900
393
399,900
393
81%
*For ASME Model: Specify D-75-399-ASME; For Propane (LP) Gas Model add suffix “LP”;
For SCAQMD Low NOx Model add prefix “N”
DIMENSIONS SHOWN IN INCHES
EXTERIOR
DIMENSIONS
ELECTRICAL
REQUIREMENTS
A
Need 120 Volt 60
Cycle AC Power
Draws less than 5 AMPS
B
753/ 4 301/4
V
E
N
T
C
661/ 4
8
2
H
G
T
TO
T&P
O
P
E
N
I
N
G
GAS
I.P.S.
CONN.
WATER I.P.S.
CONNECTIONS
(REAR & FRONT)
REAR
&
FRONT
WATER
CONN.
SIZE
HEIGHT
TO REAR
& FRONT
HOT
HEIGHT
TO REAR
& FRONT
COLD
H
G
T
F
G
H
57
191/4
4 3/ 4
S
I
Z
E
T&P
O
P
E
N
I
N
G
J
58 1/ 4
3/ 4
1
RECOVERY IN GALLONS PER HOUR AT VARIOUS TEMPERATURE RISES
MODEL
NUMBER
D-75-399-AS
TEMPERATURE RISE
GAS
TYPE
BTU
INPUT
40°
50°
60°
70°
80°
90°
100°
110°
120°
130°
140°
NAT
399,900
982
785
654
561
491
436
393
357
327
302
280
LP
399,900
982
785
654
561
491
436
393
357
327
302
280
MAXIMUM HOT WATER DELIVERABILITY AT VARIOUS TIME PERIODS
STORAGE
CAPACITY
U.S. GALLONS
ONE HOUR
RECOVERY
100° RISE
1ST HOUR
2 HOURS
3 HOURS
GPM
REC.
100° RISE
75
393
446
839
1,232
6.6
Note: Recovery rate indicated on heater rating plate is based on 75% (76%) thermal efficiency according to CSA (ANZI, Z.21.10.3).
Manufacturer reserves the right to make product changes and/or improvements with or without notice.
SAMPLE SPECIFICATION
Commercial gas water heater shall be AMERICAN STANDARD model _____________ having a storage
capacity of ________ gallons, operate on _____________ Gas, with a BTU input of _________________ and
a recovery rate of ________ gallons per hour at 100° F temperature rise. Water heater tank interior shall be
glass lined with Dura-Glas™, furnished with four anode rods and insulation shall be non-CFC foam of
R-8.3. Water heater shall be CSA certified.
Commercial Gas Water Heaters
MODEL: D-80-512-AS
80 GALLON HEAVY DUTY INSTANTANEOUS
DIRECT SPARK IGNITION DAMPERED
512,000 BTU NAT GAS
512,000 BTU L.P. GAS
The American Standard Commercial Gas Model D-80-512-AS
is designed to deliver large quantities of hot water economically
through utilization of the most energy–saving techniques.
Customary applications include industrial buildings, motels,
hotels, schools, hospitals, restaurants, laundromats, car
washes and multi-family developments up
to 30 single or 21 double bath units.
D-80-512-AS FEATURES
• Heavy Gauge Steel Tank utilizes fewer internal flue tubes resulting in fewer
critical welds to yield added years of trouble–free service.
• ASME Construction Model available.
• Inner tank glass–lined with Dura–Glas™ and fired at 1600° F for optimum protection
from the effects of corrosion.
• R-8.3 non-CFC foam insulated to save energy and reduce fuel costs by maximizing
heat retention.
• Four anode rods to prolong tank life.
• Full size hand–hole cleanout for eased tank inspection and/or removal of sediment
deposits.
• Electronic direct–spark ignition system saves fuel by eliminating the need for a
standby gas pilot.
• Automatic motorized flue damper reduces tank heat loss dur ing standby periods
for lowest operating costs.
• Fully adjustable 24–volt controls provide temperature settings to 180° F. When
installed with a mixing valve, the D-80-512-AS can deliver 180° F sanitizing and
140° F general purpose hot water simultaneously.
• Factory installed energy cut-off system and pressure/ temperature valve.
• Two inch rear and front water connections for simplified replacement of similar
units, connection to circulating lines and eased m ultiple heater or storage tank
installations. CSA certified to meet NSF/ANSI 5 Standards.
THIS WATER HEATER MEETS THE REQUIREMENTS
OF ASHRAE 90.1 1999 AND MEETS OR EXCEEDS
THE THERMAL EFFICIENCY REQUIREMENTS
OF CALIFORNIA AND OTHER STATES
RECOGNIZING ASHRAE.
• AMERICAN STANDARD gas water heaters are certified at 300 PSI test pressure
and for 150 PSI working pressure. All tanks are hydrostatically tested at the factory.
• Tested and listed with CSA International in accordance with ANSI Z21.10.3 - CSA
4.3 for up to 180° F operation as an instantaneous and/or automatic circulating
tank heater. Meets ASHRAE Standard 90.1 1999.
• Three year limited warranty on inner glass–lined tank and one y ear limited
warranty on all other component par ts.
CG 0011.3/09
D-80-512-AS SPECIFICATIONS AND APPLICATION DATA
SPECIFICATIONS
MODEL
NUMBER*
TANK
GALLONS
CAPACITY
BTU
INPUT
NAT
GAS
REC
GPH
100°
RISE
BTU
INPUT
L.P.
GAS
REC
GPH
100°
RISE
THERM
EFF
%
D-80-512-AS
80
512,000
496
512,000
496
80%
*For ASME Model: Specify D-80-512-ASME; For Propane (LP) Gas Model add
suffix “LP”; For SCAQMD Low NOx Model add prefix “N”
DIMENSIONS SHOWN IN INCHES
EXTERIOR
DIMENSIONS
ELECTRICAL
REQUIREMENTS
A
Need 120 Volt 60
Cycle AC Power
Draws less than 5 AMPS
B
721/ 4 301/4
V
E
N
T
C
661/ 4
2
10
H
G
T
TO
T&P
O
P
E
N
I
N
G
GAS
I.P.S.
CONN.
WATER I.P.S.
CONNECTIONS
(REAR & FRONT)
REAR
&
FRONT
WATER
CONN.
SIZE
HEIGHT
TO REAR
& FRONT
HOT
HEIGHT
TO REAR
& FRONT
COLD
H
G
T
F
G
H
57
191/4
4 3/ 4
S
I
Z
E
T&P
O
P
E
N
I
N
G
J
1
581/ 4
1
RECOVERY IN GALLONS PER HOUR AT VARIOUS TEMPERATURE RISES
MODEL
NUMBER
D-80-512-AS
TEMPERATURE RISE
GAS
TYPE
BTU
INPUT
40°
50°
60°
70°
80°
90°
100°
110°
120°
130°
140°
NAT
512,000
1,241
993
827
709
621
552
496
451
414
382
355
LP
512,000
1,241
993
827
709
621
552
496
451
414
382
355
MAXIMUM HOT WATER DELIVERABILITY AT VARIOUS TIME PERIODS
STORAGE
CAPACITY
U.S. GALLONS
ONE HOUR
RECOVERY
100° RISE
1ST HOUR
2 HOURS
3 HOURS
GPM
REC.
100° RISE
80
496
552
1,048
1,544
8.3
Note: Recovery rate indicated on heater rating plate is based on 75% (76%) thermal efficiency according to CSA (ANSI, Z.21.10.3).
Manufacturer reserves the right to make product changes and/or improvements with or without notice.
SAMPLE SPECIFICATION
Commercial gas water heater shall be AMERICAN STANDARD model _____________ having a storage
capacity of ________ gallons, operate on _____________ Gas, with a BTU input of _________________ and
a recovery rate of ________ gallons per hour at 100° F temperature rise. Water heater tank interior shall be
glass lined with Dura-Glas™, furnished with four anode rods and insulation shall be non-CFC foam of
R-8.3. Water heater shall be CSA certified.
“Living Up to A Higher Standard ”
Commercial Water Heaters
2808 Metropolitan Place • Pomona • CA 91767
1 (800) 900-9063 • (909) 392-0230 • Fax (909) 392-7302
Commercial Gas Water Heaters
HIGH EFFICIENCY SERIES
MODELS – Natural or LP Gas:
HE-70-125 - 70 GALLON, 125,000 BTU
HE-100-150 - 100 GALLON, 150,000 BTU
HE-100-199 - 100 GALLON, 199,000 BTU
HE-100-250 - 100 GALLON, 250,000 BTU
HE-100-250-ASME - 100 GALLON, 250,000 BTU
HIGH EFFICIENCY SERIES FEATURES
• THERMAL EFFICIENCY UP TO 98% – exceeds ASHRAE 80% requirement.
• FLEXIBLE VENTING – allows optional vertical or horizontal venting and
certified for direct vent sealed combustion applications. Provides 135
equivalent feet for 3" or 4" venting and 65 equivalent feet for 2" venting with
PVC, CPVC or ABS vent pipe.
• ELECTRONIC CONTROL OF IGNITION AND THERMOSTAT – provides
accurate water temperature settings from 100° F to 180° F. Display panel
indicates operating mode, settings and any failure modes for ease of service.
• SUBMERGED COMBUSTION CHAMBER – minimizes radiant heat loss and
improves efficiency.
• ZERO INCH CLEARANCE – to combustibles to provide additional
installation flexibility.
• INNER TANK GLASSLINED – with Dura-Glas™and fired at 1600° F for
optimum protection from the effects of corrosion.
• MAGNESIUM ANODE RODS – to extend tank life.
• NON-CFC FOAM INSULATED – to save energy and reduce fuel costs b y
maximizing heat retention.
• FULL SIZE HAND-HOLE CLEANOUT – for eased tank inspection and/or
removal of sediment deposits.
• FACTORY INSTALLED ENERGY CUT-OFF SYSTEM AND
PRESSURE/TEMPERATURE VALVE.
• CSA DESIGN CERTIFIED – in conformance with ANSI Z21.10.3-CSA4.3.
Meets and exceeds ASHRAE 90.1-1999.
• CEC listed. CSA certified to meet NSF/ANSI 5 Standards.
• LOW NOX BURNER – exceeds California SCAQMD, BAAQMD and state of
Texas requirements.
• AMERICAN STANDARD gas water heaters are certified at 300 PSI test
pressure and for 150 PSI working pressure. All tanks are hydrostatically
tested at the factory.
• THREE YEAR LIMITED WARRANTY – on inner glass-lined tank and one
year limited warranty on all other component parts.
INTERIM CG/HE 001A.7/09
SPECIFICATIONS AND APPLICATION DATA
BTU
INPUT
NAT
GAS
1ST HOUR
DELIVERY
AT 100 F°
RISE
REC
GPH
100 F°
RISE
BTU
INPUT
L.P.
GAS
REC
GPH
100 F°
RISE
THERM
EFF
%
HE-70-125
HE-100-150
HE-100-199
HE-100-250
HE-100-250-ASME
70
100
100
100
100
125,000
150,000
199,000
250,000
250,000
195
245
305
358
358
146
175
235
288
288
125,000
150,000
199,000
250,000
250,000
146
175
235
288
288
96.4%
98%
97.5%
95.3%
95.3%
MODEL
HE-70-125
HE-100-150
HE-100-199
HE-100-250
HE-100-250-ASME
E
C
* For Propane (LP)
Gas Model add
Suffix “LP”
DE
SI GN
D
MODEL
NUMBER*
U.S.
GALLONS
CAPACITY
RTIFIE
ALL DIMENSIONS IN INCHES. “TO” IS FROM FLOOR
A
B
C
D
E
TO TOP
TO
TO
TO AIR
TO
OF HTR COLD IN HOT OUT INTAKE EXHAUST
69
76 7/8
76 7/8
76 7/8
76 7/8
7 1/4
7 1/4
7 1/4
7 1/4
7 1/4
63 3/4
71 1/2
71 1/2
71 1/2
70 1/2
H
51
58
58
58
58
26 3/8
28 3/8
28 3/8
28 3/8
28 3/8
J
TO
TO
DRAIN GAS INLET
5 1/2
5 1/2
5 1/2
5 1/2
5 1/2
62 1/4
70 1/4
70 1/4
70 1/4
70 1/4
WATER
CONN
IN
OUT
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
1 1/2
GAS
CONN
T&P
CONN
APPROX
SHIP
WT Lbs
1/2
3/4
290
1/2
3/4
490
1/2
3/4
490
1/2
1
490
1/2
1
490
40 F°
RECOVERY IN GALLONS PER HOUR AT VARIOUS TEMPERATURE RISES
50 F°
60 F°
70 F°
80 F°
90 F°
100 F°
110 F°
120 F°
487
594
784
963
963
365
446
588
722
722
292
356
470
578
578
365
297
392
418
418
209
255
336
413
413
183
223
294
361
361
162
198
261
321
321
MAXIMUM EQUIVALENT VENT LENGTH (IN FEET)
INSTALLATION
CLEARANCES
SIDES
FRONT
REAR
*TOP
TO COMBUSTIBLES
9 1/4
9 1/4
9 1/4
9 1/4
9 1/4
G
HTR
DIA
30 F°
BTU INPUT
(NAT & LP)
MODEL
125,000
HE-70-125
150,000
HE-100-150
199,000
HE-100-199
250,000
HE-100-250
HE-100-250-ASME 250,000
60 1/8
68 1/8
68 1/8
68 1/8
68 1/8
F
TO
T&P
0”
0”
0”
0”
0”
MODEL
* 12” TOP FOR SERVICING RECOMMENDED
Manufacturer reserves the right to make product changes
and/or improvements with or without notice.
HE-70-125
HE-100-150
HE-100-199
HE-100-250
HE-100-250-ASME
USING 2”
PIPE
PVC. ABS
& CPVC
USING 3”
PIPE
PVC. ABS
& CPVC
USING 4”
PIPE
PVC. ABS
& CPVC
65
65
65
65
65
135
135
135
135
135
135
135
135
135
135
146
175
235
288
288
133
162
214
263
263
130 F°
140 F°
122
112
104
149
137
127
196
181
168
241
222
206
241
222
206
GAS VALVE PIPING AT INLET
MODEL
HE-70-125
HE-100-150
HE-100-199
HE-100-250
HE-100-250-ASME
Water Heaters
2808 Metropolitan Place • Pomona • CA 91767
1 (800) 900-9063 • (909) 392-0230 • Fax (909) 392-7302
1/2”
1/2”
1/2”
1/2”
1/2”