WALL POWER PACK 2
CATALOG
NUMBER
NOTES
TYPE
Ø8"
DESCRIPTION
3-1/4"
Wall mounted ballast and transformer box for use with
LED, low voltage and metal halide sources. Available to
mount over a recessed junction box (WP2J) or surface
mount (WP2S).
4-1/2"
Specifications
D:
8" OD (XXmm)
H1:
3-1/4" (XXmm)
H2:
4-1/2" (XXmm)
WP2J
WP2S
EXAMPLE: WP2J ET15 120 12C BRS
ORDERING INFORMATION
Series
Transformer and Ballasts
Voltage
Fixture Mounting
Finish
WP2J Wall Pack - Mounted
over recessed
junction box
Transformers
Metal Halide Ballasts
120
12C One 1/2" NPS at "C"
BL
Black Textured
ET151
Single 15W Electronic, LED and Halogen
20M5
20W
277
12E
Two 1/2" NPS at "E"
BRS
Bronze Smooth
ET752
Single 75W Electronic, Halogen only
35M5
35W/39W
208-2776
34C One 3/4" NPS at "C"
BRT
Bronze Textured
MT203
Single 20W Magnetic, LED and Halogen
70M5
70W
MVOLT
34E Two 3/4" NPS at "E"
CHS
Chrome Smooth
2/ET151
Double 15W Magnetic, LED and Halogen
100M5 100W
DNA
Natural Aluminum
2/ET752,4
Double 75W Magnetic and Halogen only
150M6 150W
IVS
Ivory Smooth
2/MT203
Double 20W Magnetic, LED and Halogen
NBS
Natural Bronze Smooth
SAT
Sand Textured
VET
Verde Textured
CF
Custom Finish
WP2S Wall Pack - Surface
mounted with
internal splice
compartment
MOUNTING
No Fixture
Mounting
Remote box
One Fixture
Mount at "C"
location
Two Fixture
Mounts at "E"
location
Notes:
1
ET15 and 2/ET15 are 120 volt only. They may be dimmed using ELV switches
or modules (by others) down to 5%.
2
ET75 and 2/ET75 may be dimmed using ELV switches or modules (by others)
down to a 20 watt load.
3
MT20 and 2/MT20 may be dimmed using standard MLV switches (by others).
Dimming range based on the specs of the switch chosen.
4
2/ET75 is not IC rated for ceiling mount applications.
5
Only valid with MVOLT voltage, double mounting not available.
6
150M only valid with 120 or 208-277 voltage, double mounting not available
NOTE: Hydrel Reserves The Right To Modify Specification Without Notice. Any dimension
on this sheet is to be assumed as a reference dimension: “Used for information purposes
only. It does not govern manufacturing or inspection requirements.” (ANSI Y14.5-1973)
%FFSJOH"WFOVF4FDPOE'MPPSt$IBUTXPSUI$"tXXXIZESFMDPN
1IPOFt'BY
© 2011-2015 Acuity Brands Lighting, Inc.
Rev. 01/13/15
WP2
FEATURES & SPECIFICATIONS
CONSTRUCTION: Canopy and backplate are cast from A356-T61 aluminum. All hardware is
stainless steel.
FINISHES: Available in 12 standard TGIC polyester powder coat finishes. Custom powder coat
finishes available (contact factory for more information).
LISTING: UL Listed: Wet Location. Indoor/Outdoor.
WARRANTY: 1-year limited warranty. Complete warranty terms located at
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx.
Consult factory for details.
FEATURES: Wall Power Pack can be used as a stand alone transformer or a mount canopy with
or without transformer. Backplate mounts to any standard J-box (with mount condition “J”).
Surface mount backplate (mount condition “S”) has (4) four holes for 1/2" conduit and can be
used as a splice compartment.
%FFSJOH"WFOVF4FDPOE'MPPSt$IBUTXPSUI$"tXXXIZESFMDPN
1IPOFt'BY
© 2011-2015 Acuity Brands Lighting, Inc.
Rev. 01/13/15
WP2