Trans-SPACE monocoque tipping trailers from 6500 to 8000 Standard equipment ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Tapered monocoque body 4 mm floor in HARDOX 400, 4 mm side sheets in HLE 550 4 sight windows with perspex closing plate (width: 21 cm - height: 38 cm on 1,25 m body and 63 cm on 1,5 m body) Pre-equipment for cover Optional extensions Galvanized front ladder Tubular chassis (300 x 100 x 8 mm on 6500 - 300 x 100 x 10 mm from 7000 to 8000) Chassis width: 900 mm Bolted fixed eyelet Drawbar cross spring suspension with parabolic leaves 1-part hydraulic door (DA) ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Trans-SPACE 7000/23 BC 150 Central grain chute (500 x 500 mm) Hydraulic skid with direct connection to the tractor (DA) Opening function and hydraulic skid connected to one single distributor with manual 6-way valve Oil fed tipping Double oscillating frame for tipping cylinder Galvanized and bolted mudguards Double truck-type lights (compatible with LED lights) Wheels 400R22.5 remolded Shot-blasting before painting Primer Ester Epoxy (2 K) + finishing lacquer (2 K) (total 100 µ) Forced drying (60° oven) Trans-SPACE 8000/27 TRC 150 The pictures do not correspond to standard equipment. Specific equipment Trans-SPACE BC ✓ ✓ ✓ ✓ Trans-SPACE TRC JOSKIN Roll-Over boggie with bolted table Parabolic leaves: 1.600 mm Drawbar suspension with parabolic leaves Hydraulic brakes (SA) Trans-SPACE 7500 BC ✓ ✓ ✓ ✓ Hydro-Tandem (wheel base: 1.550 mm) - hydraulic axle suspension (DA), increase of max. total load, see ref. 1775 Self steering axle Tipping stabilizer Hydraulic brakes (SA) Ref. Model (1) 4627 4628 4629 4630 4631 4632 4633 4634 4635 4636 6500/18BC125 6500/22BC150 7000/19BC125 7000/23BC150 7500/21BC125 7500/25BC150 7500/21TRC125 7500/25TRC150 8000/22TRC125 8000/27TRC150 (1) ✓ ✓ ✓ ✓ ✓ ✓ ✓ Hydro-Tridem: hydraulic axle suspension (SA + FR) with two independent and autonomous circuits (25 cm deflection) with manual valves Double self (forced) steering system (first and last axle) Drawbar suspension with parabolic leaves Air brakes Thermoplastic mudguards Tipping stabilizer Front lifting axle (DA) Pay attention to the maximum weight allowed to a loaded vehicle. See important notification on page 3. Inner body dimensions (m) DIN Max. Technically volume total Length Length Width Width permissible (m³) load below above front rear Height payload (T) 18,10 21,90 19,40 23,50 20,70 25,10 20,70 25,10 22,70 27,40 6,39 6,39 6,87 6,87 7,34 7,34 7,34 7,34 8,08 8,08 6,67 6,73 7,15 7,20 7,62 7,68 7,62 7,68 8,36 8,41 2,18 2,18 2,18 2,18 2,18 2,18 2,18 2,18 2,18 2,18 2,26 2,26 2,26 2,26 2,26 2,26 2,26 2,26 2,26 2,26 1,25 1,50 1,25 1,50 1,25 1,50 1,25 1,50 1,25 1,50 18 18 20 20 22 22 24 24 26 26 Axle(s): (mm) track (mm) - studs Brakes (mm) Cylinder (L) ADR 2x130x2000-10S ADR 2x130x2000-10S ADR 2x130x2000-10S ADR 2x130x2000-10S ADR 2x150x2000-10S ADR 2x150x2000-10S ADR 3x130x2000-10S ADR 3x130x2000-10S ADR 3x150x2000-10S ADR 3x150x2000-10S 406 x 120 406 x 120 406 x 120 406 x 120 420 x 180 420 x 180 406 x 120 406 x 120 420 x 180 420 x 180 44 44 62 62 62 62 70 70 70 70 The first 4 figures refer to the average length, the next 2 ones to the DIN volume without extensions and the last 3 ones to the height of the monocoque body. Options: page 98 and 99 - Axles: page 104 - Covers and covering: page 105 - Wheels: page 106 - 97 -