It’s not about mowing wider in the rough.
It’s about mowing wide better.
Introducing the new 9009A TerrainCut™ mower
Until now, using a wide area mower in the rough meant compromising on your quality of cut. But with our
new 9009A TerrainCut mower, you can maximize both your productivity and your cut quality.
With a 108-inch/9-foot cutting width, the 9009A is a fve-gang, 27-inch (68.58 cm)
independent rotary deck mower. A double-point yoke system on all fve decks increases
deck movement fore and aft, allowing for greater contour following and an even cut.
And the 9009A has a greater deck overlap for superior side hill mowing.
The 9009A also sports a deeper deck design with a rear discharge for greater
dispersion and a cleaner cut. And our exclusive LoadMatch™ lets you mow
in thick, lush conditions. And the 9009A features the same TechControl
display found on our A-Model mowers. The TechControl lets you set
precise mow, transport, and turn speeds while also allowing for quick
and easy diagnostics.
All height-of-cut adjustments on the
9009A can be performed without tools
with an innovative notch system. All it
takes is a simple pull of a lever.
Our unique rear deck design allows
for greater clippings dispersion and
the deeper shell stands grass up for
an even cut.
Passcode-protected TechControl display
lets you precisely set mowing speed,
turning speed, or transport speed for
consistent performance.
The double yoke on the 9009A means
the rotary decks follow the contours
in the most undulating terrain for an
exceptional quality and consistency
of cut.
9009A TerrainCut™ Rough Mower
Engine
Type
Compliant emission regulation
Maximum rated horsepower (kW)
Cylinders
Displacement
Air cleaner
Fuel
Cooling system
Vehicle
Traction type
Deck drive pump
Deck drive
Hydrostatic system capacity, U.S. gal. (L)
Fuel tank capacity, U.S. gal. (L)
Steering
Steering tires
Front drive tires
Ground pressure
Brakes
Operating Weight Wet (cutting units raised), lb. (kg)
Options available
Controls
Throttle
Forward/reverse
Mower lift
Parking brake
Seat
PTO
Brakes
ROPS
Tilt steering
Operator display
Dimension
Height with ROPS
Length
Transport width
Mowing width
Ground speeds
Mowing, mph (km/h)
Transport, mph (km/h)
Reverse, mph (km/h)
Cutting Units
Cutting deck width, in. (cm)
Height of cut range, in. (cm)
Deck construction
Blade tip speed, ft./min. (m/min)
Rear roller diameter, in. (cm)
Front rollers, in. (cm)
Fuel Economy
Actual fuel usage will vary depending on course
conditions, operation, turf and fuel quality
Warranty
Type
Certifcation
Type
Direct Inject Turbocharged Diesel B20 compliant
United States/Canada Tier 4; EU over 37.28 kW
55.1 @ 2800 rpm ISOC hp (41.1 @ 2800 rpm ISOC kW)
4
2.091 L 127.60 cu in.
2-stage dry element
Diesel
Liquid centrifugal pump; forward machine location for optimum cooling
eHydro™ servo controlled hydraulic traction pump
Tandem gear pump
Direct-coupled hydraulic gear motor
45.4 L 12 U.S. gal.
60.6 L 16 U.S. gal.
Hydraulic power with dual rod, double acting steering cylinder
20x12-10 4PR Turf
26.5x14-12 6PR Ultra Trac
12-18 psi
Internal hydraulic wet disc brakes with dynamic braking through closed loop hydrostatic system
4000 lb (1,814.37 kg)
Canopy, mulch blade, high lift blade, rear roller scraper
No throttle lever; Automatic controls with AutoPedal foot controls; manual control through TechControl display
2-pedal
One-touch single handle
Electric Switch on Command Arm for Internal Wet Disk Brakes
Air Ride Suspension seat with seat belts and arm rest; fore/aft adjustment; weight and lumbar adjustment
Electric Switch on Command Arm for quick and easy transition from mow to transport
Electric Switch on Command Arm for Internal Wet Disk Brakes
Standard, meets ISO 21299 standards
Left Foot operated for easy adjustment
TechControl Display: Located on Command Arm; displays machine warnings, on-board electrical diagnostics; service
timers on large easy to read screen; quick on the go settings for mow and transport speed; Turn Speed; Loadmatch™
and ON/OFF Weight Transfer and Cruise Control Use selection:; Cutting unit drop rate adjustment; all settings are
pass code protected
87.4 in. (2220 mm)
134 in. (3393 mm)
90 in. (2287 mm) @ 4 in. (101.60 mm) height of cut
9 Feet; 108 in. (2.74 m) 6.75 in. (17.15 cm) overlap
--0 to 8.0 mph (0 to 12.8 km/h)
0 to 12.5 mph (0 to 20.12 km/h)
0 to 5 mph (0 to 6.4 km/h)
27 in. (68.58 cm)
.75 - 4 in. (1.91 to 10.2 cm); no tool adjustment
Single 10-gauge steel stamped deck with front skid plate 1.5 in. (38mm) tall and .5 in. (12.7mm) thick steel stock
welded to the decks edge.
16,097 ft./min. (409 m/min.)
3 in. (7.62 cm)
5 in. (12.70 cm)
25% load 3.63 Liters per hour (.96 GPH) 40% Load 5.64 Liters per hour (1.49 GPH) 50% Load 6.85 liters per hour
(1.81 GPH)
Two-year limited
ANSI B71.4-2012.; CE
Sound Levels
Attachments installed
Measuring standard
--ISO 11201
Operator ear full engine rpm, dB(A)
91 dBA
Operator ear reduced engine rpm (2300 rpm)dB(A)
---
DSTE63697 (15-12)
Product features are based on published information at the time of publication and are subject to change without notice. All trademarked terms, including John Deere, the leaping deer symbol and the colors
green and yellow used herein are the property of Deere & Company, unless otherwise noted. Availability of products, product features, and other content on this site may vary by model and geographic region.
Engine horsepower and torque information for non-Deere engines are provided by the engine manufacturer for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the
engine manufacturer's Web site for additional information.