Timers and Flashers Artisan
Timers and Flashers
artisan
Part #
Description
Extended Description
Freedom10-octal
Freedom10spade
Delay on Make DPDT Timer
rated 24 – 240VAC/DC,
5 amp, adjustable from
1 second to 15 minutes
A time delay relay which provides digital control of a load operating
from any supply voltage of 24 – 240VAC/DC.
Delay time is set by two potentiometers, one “fine” for adjustment
from 1 – 100 seconds, the other from 0 – 15 minutes. Accurate time
delay achieved by combining adjustment of both potentiometers.
Freedom 10 octal
Available in standard octal or spade terminations. 5 ampere
DPDT output.
438UP
Solid-state delay on
Make Universal Timer
rated 19 – 288VAC/DC,
1 amp, adjustable from
1 – 1,000 seconds
Model 438U (Universal Time Capsule) is an all solid-state timer
providing Delay on Make control to any load operating from
19 – 288VAC/DC.
Solid-state delay on
Make Universal
Potentiometer Timer
rated 19 – 288VAC/DC,
1 amp, adjustable from
1 second – 8 minutes
Model 438UP (Universal Potentiometer Adjustable Time Capsule) is
an all solid-state timer providing Delay on Make control to any load
operating from 19 – 288VAC/DC.
Time delay is adjustable from 1 – 1000 seconds and is obtained by
connecting a fixed resistor or potentiometer across the middle
terminals (10K per second). Remains in off state when power is
applied. After preset period has elapsed, timer switches on, energizing
the load.
Solid-state delay on
Make Universal Timer
rated 19 – 288VAC/DC,
1 amp, adjustable from
1 – 1,024 seconds
438USA-3
Solid-state delay on
Make Universal Timer
rated 100 – 288VAC/DC,
1 amp, adjustable from
0.1 – 102.4 seconds
438USA-4
Solid-state delay on
Make Universal Timer
rated 19 – 288VAC/DC,
1 amp, adjustable from
2 – 2,048 seconds
438USA-INT
Solid-state interval timer
rated 24 – 240VAC,
1 amp, adjustable from
1 – 1,024 seconds
438UP
Remains in off state when power is applied. Switches on when preset
time period has elapsed, allowing load to energize. Load remains
energized as long as power is applied.
Power must be removed for at least 50 milliseconds to reset timer.
Timing adjustment is made via potentiometer located between
load terminals.
438USA
438U
438USA
Model 438USA (universal switch Adjustable Time Capsule) is an all
solid-state timer providing Delay on Make control.
Timing is set via a binary coded dip switch and is adjustable. Remains
in off state when power is applied. Switches on when preset time
period has elapsed, allowing load to energize. Load remains energized
as long as power is applied.
438USA-3
Timers and Flashers: Artisan
438U
438USA-4
Model 438USA-INT (Universal Switch Adjustable Interval Time
Capsule) is an all solid-state timer providing interval timing control of
any load device operating from 24 – 240VAC.
Timing is set via a binary coded DIP switch and is adjustable from
1 – 1024 seconds. Turns on when power is applied, permitting full load
current to flow. Turns off at end of preset timing period and permits
only leakage current to flow through the load.
438A-115-1
Solid-state delay on Make
Timer rated 115VAC/DC,
1 amp, adjustable from
10.1 – 30 seconds
Model 438 Time Capsule is an all solid-state timer providing Delay on
Make control to any 1 ampere AC or DC load such as a relay, solenoid
or lamp. Timing adjustment is made by way of an external resistor.
Consult instruction sheet for resistor selection.
438A-115-5
Solid-state delay on Make
Timer rated 115VAC/DC,
1 amp, adjustable from
30 – 8,000 seconds
After choosing a timing resistor, connect the timer in series with the
load. Polarity need not be observed. Remains in off state when power
is applied. Switches on when preset time period has elapsed, allowing
load to energize. Load remains energized as long as power is applied.
438USA-INT
438A-115-1
438A-115-5
Access Elevator supply • 800-266-8654 • Fax 510-652-5043 • www.aesupply.com
57