SUBMITTAL REVIEW SHEET
PROJECT: Canyon View Medical Plaza - Core & Shell
DATE ISSUED: 3/1/13
S U B M I T T AL #: 081113-01-04, 081416-01, 081433-01-02, 087100-01-03
S U B M I T T AL T I T L E : Doors, Frames & Hardware
C O N T R AC T O R ’ S S U B M I T T AL # : 081113-01-04, 081416-01, 081433-01-02, 087100-01-03
Owner:
Development Solutions Group
1623 Blake Street
Suite 300
Denver, CO 80202
Architect: Boulder Associates
Contractor:
GH Phipps
5995 Greenwood Plaza Blvd
Suite 100
Greenwood Village, CO 80111
Architect’s Project #: 101846.20
1426 Pearl Street
Suite 300
Boulder, CO 80302
File:
G3 - Submittals
The attached submittal was received electronically. The information contained herein is a representation of the
original electronic document.
A. Reviewed
B. Not reviewed
C. Reviewed and noted
✔
D. Resubmit
✔
E. Do not resubmit
F. Resubmit for files
The Architect’s review is for the sole purpose of aiding the contractor. The Architect is not responsible for
correctness of dimensions, quantities, details, application or fabrication of any part of the Work, nor for any
deviations from the Contract Documents. The Architect’s action does not constitute acceptance of any deviations
from the requirements of the Contract Documents.
Notes:
- Boulder Associates comments in Blue only.
- Resubmit only where specifically required by these notes or later in mark-ups, or where
additional information, clarification is requested.
- HOLD ALL DOOR AND FRAME ORDERS UNTIL VERIFICATION THAT THE DOORS OR AND
FRAMES ARE NOT AFFECTED BY CDPHE REVIEW.
- Handing, Anchors not reviewed by Boulder Associates. See floor plans for handing. GC to
coordinate required anchors
- Doors being installed in masonry walls need to use frames with larger heads to course on a brick
module.
- Tempered glazing locations where not shown on shops. All glazing panels within 18" of floor
surface, and adjacent to any side of a door frame shall be tempered, and any locations notes with
a 'T' on this shop drawing.
- Stops for glazing are to be installed on tenant side of wall u.n.o.
SUBMITTAL REVIEW SHEET
Notes:
- Submit door samples for review (standard transparent finish).
- Openings listed by others not reviewed.
- Lite Kits must match rating of the door and the entire door assembly must be labeled to the rating
requirement of the door with the lite kit.
- Clarify what sheet 86 of this document is being submitted for.
- GC to verify that overhead coiling doors are being submitted separately.
- Sub-contractor is responsible for quantities.
- Keying and keying schedule to be reviewed with Owner at future keying coordination meeting, to
be scheduled by GC near time of completion.
- GC to resubmit Rite Door hardware.
- BA cannot confirm voltage for future power operator by tenant. Is there an industry standard that
we can plan to use?
- Confirm 5"x4.5" hinges for use on doors 3'-6" or greater.
- Confirm that we are using parallel arm closers wherever possible.
- Can all door frames be provided with 3 hr label, if preferred, as the construction of the frames are
identical?
- FUTURE TENANT SUBMITTALS WILL BE NOT REVIEWED AND WILL BE REJECTED IF
SUBMITTED IN THIS FASHION. PROVIDE A SINGLE DOOR SCHEDULE AND FRAME
SCHEDULE COMBINED. ALL DOOR FRAME NUMBERING, DOOR NUMBERING AND DOOR
HARDWARE NUMBERING ARE TO MATCH THAT SHOWN ON THE ARCHITECTURAL
DRAWINGS.
Issued by: Jeff Beardsley
Signature:
TRANSMITTAL
5995 Greenwood Plaza Blvd.
Suite 100
Greenwood Village, CO 80111-4710
303-571-5377
303-629-7467 (fax)
PROJECT:
TO:
DATE: 02/15/2013
GJMC-Grand Junction Medical Center
Boulder Associates
1426 Pearl St #300
Boulder CO 80302
ATTN:
Jeff Beardsley
Ph/Fax:
303-499-7795
No. 12J2007-0063
RE:
JOB:
WE ARE SENDING:
SUBMITTED FOR:
081113-Doors, Frames and Hardwa
12J2007
ACTION TAKEN:
Shop Drawings
Approval
Approved as Submitted
Letter
Your Use
Approved as Noted
Prints
As Requested
Returned After Loan
Change Order
Review and Comment
Resubmit
Submit
Plans
SENT VIA:
Samples
Returned
Specifications / Product Data
Attached
Returned for Corrections
Other:
Separate Cover Via:
Due Date: 03/01/2013
NOTES:
Item
Package
Code
Submittal
081113
081113-01
1
02/15/2013
Submittal
081113
081113-02
1
02/15/2013
Submittal
081113
081113-03
1
02/15/2013
Submittal
081113
081113-04
1
02/15/2013
Submittal
Submittal
081113
081113
081416-01
081433-01
1
1
02/15/2013
02/15/2013
Submittal
081113
081433-02
1
02/15/2013
Submittal
Submittal
Submittal
081113
081113
081113
087100-01
087100-02
087100-03
1
1
1
02/15/2013
02/15/2013
02/15/2013
Rev. Copies Date
Description
Status
Hollow Metal Doors and Frames Product Data
Hollow Metal Doors and Frames - Shop
Drawings
Hollow Metal Doors and Frames - Door
Schedule
Hollow Metal Doors and Frames Product Data- Accessories
Flush Wood Doors - Product Data
Stile and Rail Wood Doors - Product
Data
Stile and Rail Wood Doors - Shop
Drawings
Door Hardware - Product Data
Door Hardware - Shop Drawings
Door Hardware - Schedule
Architect Review
CC:
Signed:
Brady McQuinn
Architect Review
Architect Review
Architect Review
Architect Review
Architect Review
Architect Review
Architect Review
Architect Review
Architect Review
Hollow Metal Frames- Submittal Package
Doors and Hardware Submittal Package
Can all door frames be provided with 3
hr label, if preferred, as the construction
of the frames are identical?
A
BB
42
Verify Head Detail should be 4"
Verify door size with elevator manufacturer, use
2" head with wall infill as discussed on 2/28/13
Prep for Electric Strike.
6
F
Use larger frame head in masonry opening
84
C
FR
F
72
F
F
84
F
Pair of Door/ Frame to be 7'-0" x 8'-0" - Continuous hinge
Coordinate with RITE
Recessed RITE Door Door requirements
Prep for Electric Strike.
This is a double door, I don't think any frame prep is required for strike,
6'-0" x 7'-0" Frame, Prep for Electric Strike. verify with hardware sub, use larger frame head in masonry opening
7'-0" x 7'-0" Frame.
Use larger frame head in masonry opening
Use larger frame head in masonry opening
Prep for Electrical Strike.
Prep for Electrical Strike.
Provide 45 min. rated door & frame, use larger frame head in masonry opening
Prep for Electrical Strike.
Prep for Electrical Strike.
Provide electric strike (confirm with Owner)
Door is pending re-layout of the electrical room, janitor room and quench vent shaft
Door is pending re-layout of the electrical room, janitor room and quench vent shaft
Recessed RITE Door, 7'-0" x 8'-0"
Continuous hinge, Coordinate
with RITE Door requirements
Prep for Electrical Strike.
Prep for electric strike
Please confirm no Electrical HDWR?
Please confirm no Electrical HDWR?
Prep for Electrical Strike.
No Electric Strike Required
No Electric Strike Required
GC to confirm throat size based on head and jamb detail needed for 2hr rated wall
GC to confirm throat size based on head and jamb detail needed for 2hr rated wall
Coordinate with brick
coursing, may not always be
4", depending on door height.
5'-6"
2'-0 1/4"
5' - 6 1/4"
TI
1'-6"
T
T
T
T
TH2
T
T
TD1 / TH1
T
T
T
TB / TE1
T
T
T
T
TC
T
T
TA
T
S
See sheet A8.1 for
distance off of floor
T
T
T
TD2
T
T
T
TE2
4'-8 3/8"
13'-5 3/4"
T
T
T
T
T
T
T
TF
4'-8 3/8"
86.7 degrees
13'-5 3/4"
13'-4 3/4"
4'-7 3/4"
T
T
T
TG
T
T
4'-7 3/4"
103.5 degrees
13'-4 3/4"
Installed stop shall be on tenant
side of wall, typical, u.n.o.
Door and Hardware Submittal
3333 East 52nd Ave
Denver, CO 80216-2322
Phone: 303-291-0900
Fax: 303-2910113
Original Submittal Set
PROJECT:
CANYON VIEW MEDICAL PLAZA
2373 G Road
Grand Junction, Colorado 81505
JOB NUMBER:
12435RLK
CUSTOMER:
Gerald H. Phipps Inc. ~
P O Box 3237
Englewood, Colorado 80155-3237
ARCHITECT:
Boulder Associates
1426 Pearl Street
Suite 300
Boulder, Colorado 80302
Prepared By: Rick Knowlton
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
Date: January 15, 2013
January 15, 2013
Page 2 of 24
Page 1 of 2
3333 East 52nd Avenue  Denver, CO 80216-2322  Phone (303) 291-0900  Fax (303) 291-0113
Job Name: XXXXXXXXXXXXXXXXXX
Job #: XXXXXXXX
January 15, 2013
Submittal Based on Plans Dated 11-30-12
Detailing notes:
Please provide the following required delivery dates:
Hollow metal frames
Exterior
Interior Stud
May 20th, 2013
_____________________
June 10th, 2013
_____________________
Hollow metal doors
June 10th, 2013
_____________________
Wood doors
August 1, 2013
_____________________
Door Hardware
August 1, 2013
_____________________
Standard factory lead times:
Hollow metal doors and frames – 6 weeks
Wood doors – 8 weeks
Door hardware – 6 weeks
Future TI submittals will be required to
contain a single door AND frame schedule,
labeled to match the Arch. drawings.
Please provide superintendent name and contact number
Frame Notes:
Frame submittal will be submitted by Southwestern Hollow Metal
Hollow Metal Door Notes:
This is acceptable, please confirm that
this does not affect any wood doors.
Doors are 16-18 gauge with a standard seamed edge, exteriors are galvanized 14-16 gauge
Door Type HL – These doors have parallel arm closers, we suggest changing the top rail to 8”, please confirm
Rite doors have been bid and detailed as hollow metal, please advise if alternate to add laminate faces has been
accepted
Rite doors to be painted,
Wood Door Notes:
no laminate required.
Wood doors are plain sliced white maple, AA grade, machined for hardware, factory finished, no added urea, non
FSC
Stile and Rail doors are plain sliced white maple, machined for hardware, factory finished no added urea, non FSC
Please forward the architect’s sample per specification in order for our manufacturer to produce matched samples
for approval B.A. Please advise.`
Please keep in mind with a custom color required lead time will be 8-10 weeks due to finish approval process.
submit standard transparent finish
confirm "select" white maple, as spec'd
confirm "select" white maple and
confirm balance book match, as spec'd
Page 2 of 2
3333 East 52nd Avenue  Denver, CO 80216-2322  Phone (303) 291-0900  Fax (303) 291-0113
Job Name: XXXXXXXXXXXXXXXXXX
Job #: XXXXXXXX
US26D finish is acceptable, this section
is spec'ing construction material
Door Hardware Notes:
087111-2.15A Confirm Color?
Door hardware based on Sargent grade I cylindrical locks in sating chrome finish (US26D)
We have detailed all kick plates as 10” in height, due to the 12” bottom rail requirement at the FL doors and to
match throughout, please confirm as acceptable 10" kick plate is acceptable
Hardware Set 01B – Set does not specify a stop, please advise Provide stop function in closer
Hardware Set 08 – This set is calling for an electric strike on a paired opening, but it does not call for an electric
hinge, please advise Provide proper functionality for entrance via card reader.
Thru-Bolts / Door Closers: hardware is currently detailed for use of thru-bolts on all wood doors. Please advise
whether thru-bolts are to be utilized for installation of surface mounted door closers. Can concealed fasteners be used?
Please forward owner contact information for keying requirements
Please provide aluminum supplier’s contact information so we can tie in correct cylinders for the keying system.
Pinnacle Glass, Gary Lee- 970-257-7166
Opening Notes:
111 – Hardware specification is calling for a stop arm closer for this opening, this will put the closer on the corridor
side of the opening, please confirm as acceptable Acceptable
121C – Please advise glass thickness for exterior application
Typical 1" IGU, clarify with glazing sub-contractor
131B –We have revised the door lite for the 90 minute rating, please confirm as detailed
230 –
Hardware specification is calling for a stop arm closer for this opening, this will put the closer on the
corridor side of the opening, please confirm as acceptable Acceptable
We have revised the door lite for the 90 minute rating, please confirm as detailed
240 – Hardware specification is calling for a stop arm closer for this opening, this will put the closer on the corridor
side of the opening, please confirm as acceptable Acceptable
T2 – Hardware specification is calling for a stop arm closer for this opening, this will put the closer on the exterior
side of the opening, please confirm as acceptable Acceptable
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
Opening List
Opening
101A
101B
102
103
104
105
106
107
108
109
110
111
112
113A
113B
114
115
120
121A
121B
121C
121D
121E
122
123A
123B
123C
124A
124B
124C
131A
131B
141
201
202A
202B
204
205
206
207
220
221A
221B
222
223A
223B
224
230
Hdw Set
Hdw Heading Opening Label
04
04
03
03
02
02
05
01A
06
07
07
01B
09
03
03
02
02
05
01A
06
07
07.1
01B
09
11
13
11
13
08
09.1
10
13
13
08
09.1
10
13.1
13.2
10
13
13
10
13.3
13.4
01A.1
01A.1
12
12
02
02
15
03
11
13
13
13
14
14
14
16
02
02
15
03
11
13.5
13.6
13.7
14
14.1
14.2
16
January 15, 2013
45Min
90Min
90Min
90Min
90Min
90Min
90Min
See door schedule for any
hardware set comments.
Door Type
AL-BO
AL-BO
AL-BO
FP-HM
FP-WD
FP-WD
FP-WD
FP-WD
FP-WD
NL-WD
FP-WD
FP-WD
FP-WD
FP-WD
FP-HM
AL-BO
FP-HM
FL-HM
AL-BO
HL-HM
FP-HM
FP-HM
FL-WD
FL-WD
AL-BO
FP-HM
FL-WD
FL-WD
AL-BO
AL-BO
NL-WD
AL-BO
AL-BO
FL-WD
AL-BO
FP-WD
FP-WD
FP-WD
FP-WD
FP-HM
FL-WD
FL-WD
FL-WD
FL-WD
FL-WD
FL-WD
NL-HM
Frame Type
AL-BO
AL-BO
AL-BO
SP
SP
SP
SP
SP
SP
SP
SP
SP
SP
SP
SP
SP
AL-BO
SP
TA
AL-BO
SP
SP
SP
TB
TC
AL-BO
SP
TD1
TD2
AL-BO
AL-BO
SP
AL-BO
AL-BO
TI
AL-BO
SP
SP
SP
SP
SP
TE1
TE2
TF
TH1
TH2
TG
SP
Page 3 of 24
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
240
G1
T1
T2
01B
01B.1
17
17
January 15, 2013
90Min
NL-HM
OC
OC
FP-HM
SP
OC
OC
SP
Page 4 of 24
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
Manufacturer List
Code
MC
MIHD
MIHW
PE
RO
SA
VO
January 15, 2013
Name
McKinney
MIHD
Misc. Hardware
Pemko
Rockwood
Sargent
Von Duprin
Page 5 of 24
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
Finish List
Code
AL
EN
26D
GREY
US26D
US32D
January 15, 2013
Description
Aluminum
Sprayed Finish, Aluminum
Satin Chrome
Grey
Chromium Plated, Dull
Stainless Steel, Dull
Page 6 of 24
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
Hardware Schedule
HEADING #01A (SET #01A)
Opening Description: 3' 0" x 7' 0" x 1 3/4" x WD Type NL-WDType SP
1 Single Door #110
Corridor 109 to Corridor 110
3
1
1
1
1
Hinges
Passage Set
Closer
Wall Bumper
Smoke Seal
TA2714 4 1/2 X 4 1/2
28 10U15 LP
351 P9 TB
409
S88 D 17'
90
26D
26D
EN
US32D
LH
MC
SA
SA
RO
PE
HEADING #01A.1 (SET #01A.1)
Opening Description: 4' 0" x 7' 0" x 1 3/4" x WD Type NL-WDType SP x 90Min
1 Single Door #131B
Vestibule 131 from Corridor 110
3
1
1
1
1
Hinges
Passage Set
Closer
Wall Bumper
Smoke Seal
TA2714 5 X 4 1/2
28 10U15 LP
351 O TB
Include through bolts @ rated door
409
S88 D 18'
90
26D
26D
EN
US32D
RHR
MC
SA
SA
RO
PE
HEADING #01B (SET #01B)
Opening Description: 3' 0" x 7' 0" x 1 3/4" x WD Type FP-WDType SP x 90Min
1 Single Door #113B
ASC Elec 113 to C&S Elec 112
3
1
1
1
Hinges
Passage Set
Closer
Smoke Seal
TA2714 4 1/2 X 4 1/2
28 10U15 LP Provide stop function in closer
351 PS TB
Include through bolts @ rated door
S88 D 17'
90
26D
26D
EN
RH
MC
SA
SA
PE
HEADING #01B.1 (SET #01B)
Opening Description: 3' 0" x 7' 0" x 1-3/4" x HM Type NL-HMType SP x 90Min
1 Single Door #240
Stair 240 from Corridor 203
3
1
1
1
Hinges
Passage Set
Closer
Smoke Seal
January 15, 2013
TA2714 4 1/2 X 4 1/2 Provide stop function in closer
28 10U15 LP
Include through bolts @ rated door
351 PS TB
S88 D 17'
90
26D
26D
EN
LHR
MC
SA
SA
PE
Page 7 of 24
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
HEADING #02 (SET #02)
Opening Description: 3' 0" x 7' 0" x 1 3/4" x WD Type FP-WDType SP
1 Single Door #107
Lobby 102 to Mens 107
1 Single Door #108
Lobby 102 to Womens 108
1 Single Door #204
Corridor 203 to Womens 204
1 Single Door #205
Corridor 203 to Mens 205
12
4
4
4
4
4
4
Hinges
Push Plate
Door Pull
Closer
Protection Plate
Wall Bumper
Smoke Seal
TA2714 4 1/2 X 4 1/2
70G 4 X 20
111
351 O TB
K1050 10" x 34"
409
S88 D 17'
90
90
90
90
26D
US32D
US32D
EN
US32D
US32D
LH
RH
RH
LH
MC
RO
RO
SA
RO
RO
PE
HEADING #03 (SET #03)
Opening Description: 3' 0" x 7' 0" x 1 3/4" x WD Type FP-WDType SP
1 Single Door #105
Corridor 109 to Janitor 105
1 Single Door #106
Corridor 109 to Bldg Mgr 106
1 Single Door #207
Corridor 203 to JC 207
9
3
3
3
3
3
Hinges
Lockset
Closer
Protection Plate
Wall Bumper
Smoke Seal
TA2714 4 1/2 X 4 1/2
28 10G04 LP (CMK MK)
351 O TB
K1050 10" x 34"
409
S88 D 17'
90
90
90
26D
26D
EN
US32D
US32D
LH
LH
RH
MC
SA
SA
RO
RO
PE
HEADING #04 (SET #04)
Opening Description: 3' 0" x 7' 0" x 1-3/4" x HM Type FP-HMType SP
1 Single Door #103
Lobby 102 to Elev Equip 103
3
1
1
1
1
1
Hinges
Lockset
Closer
Wall Bumper
Smoke Seal
Auto Door Bottom
TA2714 4 1/2 X 4 1/2
28 10G04 LP (CMK MK)
351 O TB
409
S88 D 17'
411 APKL 36"
90
26D
26D
EN
US32D
RH
MC
SA
SA
RO
PE
PE
HEADING #05 (SET #05)
Opening Description: 4' 0" x 7' 0" x 1 3/4" x WD Type FP-WDType SP
1 Single Door #109
Lobby 102 from Corridor 109
3
1
1
1
1
1
Hinges
Lockset
Electric Strike
Closer
Wall Bumper
Smoke Seal
January 15, 2013
TA2714 5 X 4 1/2
28 10G04 LP (CMK MK)
6211 24VDC FSE
351 P9 TB
409
S88 D 18'
90
26D
26D
US32D
EN
US32D
LHR
MC
SA
VO
SA
RO
PE
Page 8 of 24
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
HEADING #06 (SET #06)
Opening Description: 3' 0" x 7' 0" x 1 3/4" x WD Type FP-WDType SP
1 Single Door #111
Corridor 110 to IT 111
3
1
1
1
Hinges
Lockset
Closer
Smoke Seal
TA2714 4 1/2 X 4 1/2
28 10G04 LP (CMK MK)
351 PS TB Provide stop function in closer
S88 D 17'
90
26D
26D
EN
LH
MC
SA
SA
PE
HEADING #07 (SET #07)
Opening Description: 3' 0" x 7' 0" x 1 3/4" x WD Type FP-WDType SP x 45Min
1 Single Door #112
Corridor 110 from C&S Elec 112
3
1
1
1
1
Hinges
Lockset
Closer
Wall Bumper
Smoke Seal
TA2714 4 1/2 X 4 1/2
28 10G04 LP (CMK MK)
351 P9 TB Provide 180 degree open function in closer
409
S88 D 17'
180
26D
26D
EN
US32D
LHR
MC
SA
SA
RO
PE
HEADING #07.1 (SET #07)
Opening Description: 3' 0" x 7' 0" x 1 3/4" x WD Type FP-WDType SP x 90Min
1 Single Door #113A
Corridor 110 from ASC Elec 113
3
1
1
1
1
Hinges
Lockset
Closer
Wall Bumper
Smoke Seal
TA2714 4 1/2 X 4 1/2
28 10G04 LP (CMK MK)
351 P9 TB Provide 180 degree open function in closer
409
S88 D 17'
180
26D
26D
EN
US32D
LHR
MC
SA
SA
RO
PE
HEADING #08 (SET #08)
Opening Description: 2 - 3' 0" x 7' 0" x 1-3/4" x HM Type HL-HMType SP
1 Pair Doors #121C
Exterior from ASC 121
6
2
1
1
2
1
1
1
1
2
1
Hinges
Flush Bolts
Lockset
Electric Strike
Closer
Dust Proof Strike
Weatherstrip
Astragal
Door Bottom
Threshold
TA2714 4 1/2 X 4 1/2
555
28 10G04 LP (CMK MK)
6223 24VDC FSE
351 PSH TB Provide hold-open function in closer
570
CARD READER "BY OTHERS"
316 DPK 1 x 72" 2 x 84"
355 CS 84"
315 CN 36"
170 A 72"
90
26D
US26D
26D
US32D
EN
US26D
AL
RHRA
MC
RO
SA
VO
SA
RO
MIHW
PE
PE
PE
PE
- Clarify if coordinator is required with manual flush bolts and astragal.
- Provide proper functionality for entrance via card reader.
January 15, 2013
Page 9 of 24
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
HEADING #09 (SET #09)
Does this HDWR Group require coordinator?
No
Opening Description: 2 - 4' 0" x 7' 0" x 1-3/4" x HM Type FP-HMType SP
1 Pair Doors #114
Exterior from Mech 114
6
2
1
1
2
1
1
2
1
Hinges
Flush Bolts
Dust Proof Strike
Lockset
Closer
Astragal
Weatherstrip
Door Bottom
Threshold
90
TA2714 5 X 4 1/2
555
570
28 10G04 LP (CMK MK)
351 PSH TB Provide hold-open function in closer
355 CS 84"
316 DPK 1 x 96" 2 x 84"
315 CN 48"
170 A 96"
HEADING #09.1 (SET #09.1) Does this HDWR Group require coordinator?
26D
US26D
US26D
26D
EN
Hinges
Flush Bolts
Lockset
Closer
Dust Proof Strike
Weatherstrip
Astragal
Door Bottom
Threshold
TA2714 4 1/2 X 4 1/2
555
28 10G04 LP (CMK MK)
351 PSH TB Provide hold-open function in closer
570
316 DPK 1 x 72" 2 x 84"
355 CS 84"
315 CN 36"
170 A 72"
MC
RO
RO
SA
SA
PE
PE
PE
PE
No
Opening Description: 2 - 3' 0" x 7' 0" x 1-3/4" x HM Type FP-HMType SP
1 Pair Doors #121D
Exterior from ASC 121
6
2
1
2
1
1
1
2
1
RHRA
90
26D
US26D
26D
EN
US26D
AL
RHRA
MC
RO
SA
SA
RO
PE
PE
PE
PE
HEADING #10 (SET #10)
Opening Description: 3' 0" x 7' 0" x 1-3/4" x HM Type FP-HMType SP
1 Single Door #121E
Exterior from ASC 121
1 Single Door #123C
Exterior from Imaging 123
6
2
2
2
2
2
Hinges
Lockset
Closer
Weatherstrip
Door Bottom
Threshold
TA2714 4 1/2 X 4 1/2
28 10G04 LP (CMK MK)
351 PSH TB Provide hold-open function in closer
316 DPK 1 x 36" 2 x 84"
315 CN 36"
170 A 36"
90
90
26D
26D
EN
RHR
RHR
MC
SA
SA
PE
PE
PE
AL
HEADING #11 (SET #11) Recessed RITE Door per A8.1 Door Schedule
Opening Description: 2 - 3' 6" x 8' 0" x HMD Type FP-HMType SP x 90Min
1 Pair Doors #120
Lobby 102 from Stair 120
1 Pair Doors #220
Stair 220 from Lobby 201
2 Hardware by Door
MFC(By Others)
HARDWARE BY DOOR MANUFACTURER
90
90
RHRA
RHRA
MIHW
Note: All other hardware comes with door.
January 15, 2013
Page 10 of 24
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
HEADING #12 (SET #12)
Opening Description: 3' 0" x 8' 0" x 1-3/4" x WD Type FL-WDType TI
1 Single Door #202A
Lobby 201 to Conference 202
4
1
1
1
1
Hinges
Lockset
Closer
Wall Bumper
Smoke Seal
TA2714 4 1/2 X 4 1/2
28 10G04 LP (CMK MK)
351 O TB
409
S88 D 20'
90
26D
26D
EN
US32D
LH
MC
SA
SA
RO
PE
HEADING #13 (SET #13)
Opening Description: 3' 6" x 8' 0" x 1-3/4" x HM Type FL-HMType TA
1 Single Door #121A
Corridor 115 from ASC 121
4
1
1
1
Hinges
Lockset
Electric Strike
Automatic Operator(By
Others)
1 Protection Plate
1 Dome Stop
1 Smoke Seal
90
LHR
TA2714 5 X 4 1/2
Voltage must be coordinated 26D
28 10G05 LP (CMK MK)
by power operator supplier. 26D
6211 24VDC FSE
US32D
OPERATOR BY OTHERS Normally 12V.
AL
MC
SA
VO
MIHD
K1050 8" x 40"
440
10"?
S88 D 20'
RO
RO
PE
B.A. Please confirm.
Provide 10"
US32D
US26D
HEADING #13.1 (SET #13)
Opening Description: 3' 6" x 8' 0" x 1-3/4" x WD Type FL-WDType TB
1 Single Door #122
Lobby 102 from Urgent Care 122
4
1
1
1
Hinges
Lockset
Electric Strike
Automatic Operator(By
Others)
1 Protection Plate
1 Dome Stop
1 Smoke Seal
90
RHR
TA2714 5 X 4 1/2
Voltage must be coordinated 26D
28 10G05 LP (CMK MK)
26D
by power operator supplier. US32D
6211 24VDC FSE
OPERATOR BY OTHERS Normally 12V.
AL
MC
SA
VO
MIHD
K1050 8" x 40"
440
10"?
S88 D 20'
RO
RO
PE
B.A. Please confirm.
Provide 10"
US32D
US26D
HEADING #13.2 (SET #13)
Opening Description: 3' 6" x 8' 0" x 1-3/4" x WD Type FL-WDType TC
1 Single Door #123A
Lobby 102 from Imaging 123
4
1
1
1
Hinges
Lockset
Electric Strike
Automatic Operator(By
Others)
1 Protection Plate
1 Dome Stop
1 Smoke Seal
January 15, 2013
90
RHR
TA2714 5 X 4 1/2
26D
28 10G05 LP (CMK MK)
26D
Voltage must be coordinated US32D
6211 24VDC FSE
OPERATOR BY OTHERS by power operator supplier. AL
MC
SA
VO
MIHD
K1050 8" x 40"
440
10"?
S88 D 20'
RO
RO
PE
Normally 12V.
B.A. Please confirm.
Provide 10"
US32D
US26D
Page 11 of 24
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
HEADING #13.3 (SET #13)
Opening Description: 3' 6" x 8' 0" x 1-3/4" x WD Type FL-WDType TD1
1 Single Door #124A
Lobby 102 from Western Ortho 124
4
1
1
1
Hinges
Lockset
Electric Strike
Automatic Operator(By
Others)
1 Protection Plate
1 Dome Stop
1 Smoke Seal
90
LHR
TA2714 5 X 4 1/2
26D
28 10G05 LP (CMK MK) Voltage must be coordinated26D
6211 24VDC FSE
by power operator supplier. US32D
OPERATOR BY OTHERS
AL
MC
SA
VO
MIHD
K1050 8" x 40"
440
10"?
S88 D 20'
RO
RO
PE
Normally 12V.
B.A. Please confirm.
Provide 10"
US32D
US26D
HEADING #13.4 (SET #13)
Opening Description: 3' 6" x 8' 0" x 1-3/4" x WD Type FL-WDType TD2
1 Single Door #124B
Lobby 102 from Western Ortho 124
4
1
1
1
Hinges
Lockset
Electric Strike
Automatic Operator(By
Others)
1 Protection Plate
1 Dome Stop
1 Smoke Seal
90
LHR
TA2714 5 X 4 1/2
Voltage must be coordinated 26D
28 10G05 LP (CMK MK)
26D
by power operator supplier. US32D
6211 24VDC FSE
OPERATOR BY OTHERS Normally 12V.
AL
MC
SA
VO
MIHD
K1050 8" x 40"
440
10"?
S88 D 20'
RO
RO
PE
B.A. Please confirm.
Provide 10"
US32D
US26D
HEADING #13.5 (SET #13)
Opening Description: 3' 6" x 8' 0" x 1-3/4" x WD Type FL-WDType TE1
1 Single Door #221A
Lobby 201 from Urological
Associates 221
4
1
1
1
Hinges
Lockset
Electric Strike
Automatic Operator(By
Others)
1 Protection Plate
1 Dome Stop
1 Smoke Seal
January 15, 2013
90
RHR
TA2714 5 X 4 1/2
26D
28 10G05 LP (CMK MK)
26D
Voltage must be coordinated US32D
6211 24VDC FSE
OPERATOR BY OTHERS by power operator supplier. AL
MC
SA
VO
MIHD
K1050 8" x 40"
440
10"?
S88 D 20'
RO
RO
PE
Normally 12V.
B.A. Please confirm.
Provide 10"
US32D
US26D
Page 12 of 24
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
HEADING #13.6 (SET #13)
Opening Description: 3' 6" x 8' 0" x 1-3/4" x WD Type FL-WDType TE2
1 Single Door #221B
Lobby 201 from Urological
Associates 221
4
1
1
1
Hinges
Lockset
Electric Strike
Automatic Operator(By
Others)
1 Protection Plate
1 Dome Stop
1 Smoke Seal
90
RHR
TA2714 5 X 4 1/2
26D
28 10G05 LP (CMK MK) Voltage must be coordinated26D
6211 24VDC FSE
by power operator supplier. US32D
OPERATOR BY OTHERS Normally 12V.
AL
MC
SA
VO
MIHD
K1050 8" x 40"
440
10"?
S88 D 20'
RO
RO
PE
B.A. Please confirm.
Provide 10"
US32D
US26D
HEADING #13.7 (SET #13)
Opening Description: 3' 6" x 8' 0" x 1-3/4" x WD Type FL-WDType TF
1 Single Door #222
Lobby 102 from Surgical Associates
222
4
1
1
1
Hinges
Lockset
Electric Strike
Automatic Operator(By
Others)
1 Protection Plate
1 Dome Stop
1 Smoke Seal
90
RHR
TA2714 5 X 4 1/2
26D
28 10G05 LP (CMK MK) Voltage must be coordinated 26D
6211 24VDC FSE
by power operator supplier. US32D
OPERATOR BY OTHERS Normally 12V.
AL
MC
SA
VO
MIHD
K1050 8" x 40"
440
10"?
S88 D 20'
RO
RO
PE
B.A. Please confirm.
Provide 10"
US32D
US26D
HEADING #14 (SET #14)
Opening Description: 3' 6" x 8' 0" x 1-3/4" x WD Type FL-WDType TH1
1 Single Door #223A
Corridor 203 from Mesa Womens
Health 223
4
1
1
1
1
Hinges
Lockset
Protection Plate
Dome Stop
Smoke Seal
90
TA2714 5 X 4 1/2
26D
28 10G05 LP (CMK MK) Verify Card Reader?
26D
K1050 8" x 40" Provide 10"
US32D
TYP. all tenant spaces
440
US26D
S88 D 20'
Not required at HW-14
LHR
MC
SA
RO
RO
PE
HEADING #14.1 (SET #14)
Opening Description: 3' 6" x 8' 0" x 1-3/4" x WD Type FL-WDType TH2
1 Single Door #223B
Corridor 203 from Mesa Womens
Health 223
4
1
1
1
1
Hinges
Lockset
Protection Plate
Dome Stop
Smoke Seal
January 15, 2013
90
TA2714 5 X 4 1/2
26D
28 10G05 LP (CMK MK) Verify Card Reader?
26D
K1050 8" x 40" Provide 10" TYP. all tenant spaces
US32D
440
US26D
S88 D 20'
Not required at HW-14
LHR
MC
SA
RO
RO
PE
Page 13 of 24
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
HEADING #14.2 (SET #14)
Opening Description: 3' 6" x 8' 0" x 1-3/4" x WD Type FL-WDType TG
1 Single Door #224
Lobby 201 from Unassigned 224
4
1
1
1
1
Hinges
Lockset
Protection Plate
Dome Stop
Smoke Seal
TA2714 5 X 4 1/2
28 10G05 LP (CMK MK)
K1050 8" x 40" Provide 10"
440
S88 D 20'
90
26D
26D
US32D
US26D
LHR
MC
SA
RO
RO
PE
HEADING #15 (SET #15)
Opening Description: 3' 0" x 7' 0" x 1 3/4" x WD Type FP-WDType SP
1 Single Door #206
Corridor 203 to Elec/IT 206
3
1
1
1
1
Hinges
Lockset
Closer
Dome Stop
Smoke Seal
TA2714 4 1/2 X 4 1/2
28 10G04 LP (CMK MK)
351 O TB
440
S88 D 17'
90
26D
26D
EN
US26D
RH
MC
SA
SA
RO
PE
HEADING #16 (SET #16)
Opening Description: 3' 0" x 7' 0" x 1-3/4" x HM Type NL-HMType SP x 90Min
1 Single Door #230
Stair 230 from Urological Associates
221
3
1
1
1
1
Hinges
Lockset
Electric Strike
Closer
Smoke Seal
TA2714 4 1/2 X 4 1/2
28 10G04 LP (CMK MK)
6211 24VDC FSE
351 PS TB
S88 D 17'
90
26D
26D
US32D
EN
RHR
MC
SA
VO
SA
PE
HEADING #17 (SET #17)
Opening Description: 3' 0" x 7' 0" x 1-3/4" x HM Type FP-HMType SP
1 Single Door #T2
Exterior to Trash Enclosure
3
1
1
3
Hinges
Passage Set
Closer
Door Silencers
January 15, 2013
TA2714 4 1/2 X 4 1/2
28 10U15 LP
351 PS TB Provide stop function in closer
608
90
26D
26D
EN
GREY
RH
MC
SA
SA
RO
Page 14 of 24
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
Door Frame Submittal Legend
Manufacturer
CC
HG01
MS
SWHM
WDGE
Curries Company
Hollow Metal Generic
Marshfield Door Systems
Southwestern Hollow Metal
Wood Door Generic
Door Description
CC
HG01
MS
WDGE
HM
HMD
WD
WD
HM Door
Hollow Metal
Wood Door
Wood Door
HG01 FE
WDGE LVL
Filled Edge - Finished Smooth
Composite Wood Edge
CC
STY
HG01 STY
MS
MC
PC
WDGE PC
Polystyrene Core
Polystyrene Core
Mineral Core
Particle Core
Particleboard Core
HG01 PRIME
MS
STAIN_C
WDGE STAIN_C
Prime only
Stain Custom
Stain Custom
WDGE 5PLY
5-Ply
Door Core
Door Finish
Door Series
CC
707
HG01 FFS
MS
EDFMUF
EDPCUF
WDGE SFG
Styrene Core Std/Urethane Optional
Full Flush Seamless Edge Door
Environmental Mineral Core UF Free Fire Rated
Environmental Particle Core UF Free
Single Lite Full Glass Door
CC
14
16
18
HG01 18
14 Gauge
16 Gauge
18 Gauge
18 Gauge
CC
HG01
MS
WDGE
1 3/4in Door or Panel
1-3/4" Thick
1 3/4" Thick Door
1-3/4" Thick
Door Ply
Door Gauge
Door Thickness
1-3/4"
1-3/4"
1 3/4"
1-3/4"
Door Material
CC
CR
RK
HG01 CRS
MS
PSWM
WDGE MAPLE
Cold Rolled Steel
A60 Galvaneal
Cold Rolled Steel
Plain Sliced White Maple
Maple
CC
Dr Edge Seam Not Filled
Door Edge
S
January 15, 2013
Page 15 of 24
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
Door Frame Submittal
Opening
Opening
Number
101A
Hdw Hdw
Qty Hdg Set Rating
Door
Wall
Cond
1
Sill
Arch
Type Desc Thick Series
ALBO
Frame
Leaf
Size
Ga/
Matl Core Ply Edge Finish
Elev
Code
Mfg
14980
**
14980
**
ALBO
4080
**
ALBO
3070
3670
CC
MS
FPHM
WD
4070
**
3070
MS
FPWD
WD 1 3/4"
EDPC PSW
UF
M
PC
STAIN_
C
FP
3070
MS
FPWD
WD 1 3/4"
EDPC PSW
UF
M
PC
STAIN_
C
3070
MS
FPWD
WD 1 3/4"
EDPC PSW
UF
M
PC
3070
MS
FPWD
WD 1 3/4"
EDPC PSW
UF
M
4070
MS
FPWD
WD 1 3/4"
3070
MS
NLWD
3070
MS
3070
Hand
Arch
Type Desc Matl
ALBO
Jamb/
Elev
Series Profile Ga Cons Throat Head Code
Size
Mfg
14980
**
Anchor
Hand
14980
**
ALBO
RHR
4080
**
ALBO
LH
RH
3070
3670
SWH
M
SP
Hold door until size and swing are verified by elevator manufacturer (likely
RH
3-6x7-0, provide wood door, this was erroneously labeled in the door schedule.
4070
SWH
M
SP
LH
3070
SWH
M
SP
FP
LH
3070
SWH
M
SP
LH
STAIN_
C
FP
LH
3070
SWH
M
SP
LH
PC
STAIN_
C
FP
RH
3070
SWH
M
SP
RH
EDPC PSW
UF
M
PC
STAIN_
C
FP
LHR
4070
SWH
M
SP
RH
WD 1 3/4"
EDPC PSW
UF
M
PC
STAIN_
C
NL
LH
3070
SWH
M
SP
LH
FPWD
WD 1 3/4"
EDPC PSW
UF
M
PC
STAIN_
C
FP
LH
3070
SWH
M
SP
LH
MS
FPWD
WD 1 3/4"
EDFM PSW
UF
M
MC
STAIN_
C
FP
LHR
3070
SWH
M
SP
RH
3070
MS
FPWD
WD 1 3/4"
EDFM PSW
UF
M
MC
STAIN_
C
FP
LHR
3070
SWH
M
SP
RH
3070
MS
FPWD
WD 1 3/4"
EDFM PSW
UF
M
MC
STAIN_
C
FP
RH
3070
SWH
M
SP
RH
4070
CC
FPHM
HM 1-3/4"
707
RK
STY
14
S
FP
RHR
8070
SWH
M
SP
RHRA
HM 1-3/4"
707
RK
STY
14
S
FP
LHR
LHR
3080
**
ALBO
RH
RHR
7080
SWH
M
SP
RHRA
Exterior to/from Vest 101
101B
1
Vest 101 to/from Lobby 102
102
1
Exterior from Lobby 102
103
1
04
04
Lobby 102 to Elev Equip 103
104
1
HM 1-3/4" 707
CR STY
EDPC PSW PC
WD
UF
M
18
S
STAIN_
C
FP
Lobby 102 to/from Mail/Vending 104
105
1
03
03
Provide 3/4" undercut
LH
Corridor 109 to Janitor 105
106
1
03
03
Corridor 109 to Bldg Mgr 106
107
1
02
02
Lobby 102 to Mens 107
108
1
02
02
Lobby 102 to Womens 108
109
1
05
05
Lobby 102 from Corridor 109
110
1
01A
01A
Corridor 109 to Corridor 110
111
1
06
06
Corridor 110 to IT 111
112
1
07
07
45Min
Corridor 110 from C&S Elec 112
113A
1
07.1
07
90Min
Corridor 110 from ASC Elec 113
113B
1
01B
01B
90Min
ASC Elec 113 to C&S Elec 112
114
1
09
09
Exterior from Mech 114
114
1
4070
CC
115
1
3080
**
FPHM
ALBO
Exterior from Corridor 115
120
1
11
11
90Min
Lobby 102 from Stair 120
January 15, 2013
FP3680 HG01
HMD 1-3/4"
HM
Leaf #1 Notes: Rite Door, D3676
FFS
CRS STY
18
FE
PRIME
FP
Page 16 of 24
Weld
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
Opening
Opening
Number
120
121A
Hdw Hdw
Qty Hdg Set Rating
Door
Wall
Cond
1
1
13
13
Sill
Frame
Leaf
Size
Arch
Mfg Type Desc Thick Series Matl Core
FP3680 HG01
HMD 1-3/4" FFS CRS STY
HM
Leaf #2 Notes: Rite Door, D3676
FL3680
CC
HM 1-3/4" 707
CR STY
HM
Ga/
Ply Edge Finish
18
FE
16
S
PRIME
Elev
Code
Hand
Size
FP
LHR
90 min. rated
FL.1
LHR
3680
SWH
M
TA
RH
LHR
4080
**
ALBO
RH
RHR
6070
SWH
M
SP
RHRA
6070
SWH
M
SP
RHRA
Mfg
Arch
Type Desc Matl
Jamb/
Elev
Series Profile Ga Cons Throat Head Code
Anchor
Hand
Corridor 115 from ASC 121
121B
1
4080
**
ALBO
3070
CC
HLHM
3070
CC
3070
CC
3070
CC
3070
CC
Exterior from ASC 121
121C
1
08
08
HM 1-3/4"
707
RK
STY
16
S
HL
Exterior from ASC 121
121C
1
121D
1
09.1
09.1
HLHM
FPHM
HM 1-3/4"
707
RK
STY
16
S
HL
LHR
HM 1-3/4"
707
RK
STY
16
S
FP
RHR
Exterior from ASC 121
121D
1
121E
1
10
10
FPHM
FPHM
HM 1-3/4"
707
RK
STY
16
S
FP
LHR
HM 1-3/4"
707
RK
STY
16
S
FP
RHR
3070
SWH
M
SP
LH
Exterior from ASC 121
122
1
13.1
13
3680
WDG FLE
WD
WD 1-3/4" SFG
MAPL
PC
E
5PL
STAIN_
LVL
FL.1
Y
C
RHR
3680
SWH
M
TB
LH
3680
WDG FLE
WD
WD 1-3/4" SFG
MAPL
PC
E
5PL
STAIN_
LVL
FL.1
Y
C
RHR
3680
SWH
M
TC
LH
LHR
4080
**
ALBO
RH
RHR
3070
SWH
M
SP
Lobby 102 from Urgent Care 122
123A
1
13.2
13
Lobby 102 from Imaging 123
123B
1
4080
**
ALBO
3070
CC
FPHM
Exterior from Imaging 123
123C
1
10
10
HM 1-3/4"
707
RK
STY
16
S
FP
Provide 45 min. rated door & frame
LH
Exterior from Imaging 123
124A
1
13.3
13
3680
WDG FLE
WD
WD 1-3/4" SFG
MAPL
PC
E
5PL
STAIN_
LVL
FL.1
Y
C
LHR
3680
SWH
TD1
M
RH
3680
WDG FLE
WD
WD 1-3/4" SFG
MAPL
PC
E
5PL
STAIN_
LVL
FL.1
Y
C
LHR
3680
SWH
TD2
M
RH
Lobby 102 from Western Ortho 124
124B
1
13.4
13
Lobby 102 from Western Ortho 124
124C
1
3080
**
ALBO
RHR
3080
**
ALBO
LH
4080
**
ALBO
RHR
4080
**
ALBO
LH
4070
MS
NLWD
RHR
4070
SWH
M
SP
LH
4080
**
ALBO
LHR
4080
**
ALBO
RH
3280
**
ALBO
RHR
3280
**
ALBO
LH
LH
3080
SWH
M
TI
LH
Exterior from Western Ortho 124
131A
1
Exterior from Vestibule 131
131B
1
01A.1 01A.1 90Min
WD 1 3/4"
EDFM PSW
UF
M
MC
STAIN_
NLR
C
Vestibule 131 from Corridor 110
141
1
Exterior from Vestibule 141
201
1
Exterior from Lobby 201
202A
1
12
12
3080
WDG FLE
WD
WD 1-3/4" SFG
MAPL
PC
E
5PL
STAIN_
LVL
Y
C
FL
Lobby 201 to Conference 202
January 15, 2013
Page 17 of 24
Weld
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
Opening
Opening
Number
202B
Hdw Hdw
Qty Hdg Set Rating
Door
Wall
Cond
Sill
1
Arch
Type Desc Thick Series
ALBO
Frame
Leaf
Size
Ga/
Matl Core Ply Edge Finish
Mfg
3080
**
3070
MS
FPWD
WD 1 3/4"
EDPC PSW
UF
M
PC
STAIN_
C
3070
MS
FPWD
WD 1 3/4"
EDPC PSW
UF
M
PC
3070
MS
FPWD
WD 1 3/4"
EDPC PSW
UF
M
3070
MS
FPWD
WD 1 3/4"
EDPC PSW
UF
M
Elev
Code
Arch
Type Desc Matl
ALBO
Jamb/
Elev
Series Profile Ga Cons Throat Head Code
Hand
Size
Mfg
RHR
3080
**
Anchor
Hand
FP
RH
3070
SWH
M
SP
STAIN_
C
FP
LH
3070
SWH
M
SP
Door is pending re-layout of the electrical
room, janitor room and quench vent shaft.
LH
PC
STAIN_
C
FP
RH
3070
SWH
M
SP
Door is pending re-layout of the electrical
room, janitor room and quench vent shaft.
RH
PC
STAIN_
C
FP
RH
3070
SWH
M
SP
Provide 3/4" undercut
RH
RHR
7080
SWH
M
SP
LH
Exterior from Conference 202
204
1
02
02
RH
Corridor 203 to Womens 204
205
1
02
02
Corridor 203 to Mens 205
206
1
15
15
Corridor 203 to Elec/IT 206
207
1
03
03
Corridor 203 to JC 207
220
1
11
11
90Min
Stair 220 from Lobby 201
220
1
221A
1
13.5
13
FPHMD 1-3/4" FFS CRS STY 18 FE PRIME
FP
HM
Leaf #1 Notes: Rite Door, D3676
FP3680 HG01
HMD 1-3/4" FFS CRS STY 18 FE PRIME
FP
HM
Leaf #2 Notes: Rite Door, D3676
WDG FLMAPL
5PL
STAIN_
3680
WD 1-3/4" SFG
PC
LVL
FL.1
E
WD
E
Y
C
3680
HG01
LHR
RHRA
90 min. rated
RHR
3680
SWH
TE1
M
LH
Lobby 201 from Urological Associates 221
221B
1
13.6
13
3680
WDG FLE
WD
WD 1-3/4" SFG
MAPL
PC
E
5PL
STAIN_
LVL
FL.1
Y
C
RHR
3680
SWH
TE2
M
LH
3680
WDG FLE
WD
WD 1-3/4" SFG
MAPL
PC
E
5PL
STAIN_
LVL
FL.1
Y
C
RHR
3680
SWH
M
LH
3680
WDG FLE
WD
WD 1-3/4" SFG
MAPL
PC
E
5PL
STAIN_
LVL
FL.1
Y
C
LHR
3680
SWH
TH1
M
RH
3680
WDG FLE
WD
WD 1-3/4" SFG
MAPL
PC
E
5PL
STAIN_
LVL
FL.1
Y
C
LHR
3680
SWH
TH2
M
RH
3680
WDG FLE
WD
WD 1-3/4" SFG
MAPL
PC
E
5PL
STAIN_
LVL
FL.1
Y
C
LHR
3680
SWH
M
TG
RH
Lobby 201 from Urological Associates 221
222
1
13.7
13
TF
Lobby 102 from Surgical Associates 222
223A
1
14
14
Corridor 203 from Mesa Womens Health
223
223B
1
14.1
14
Corridor 203 from Mesa Womens Health
223
224
1
14.2
14
Lobby 201 from Unassigned 224
230
1
16
16
90Min
3070
CC
NLHM
HM 1-3/4"
707
CR
STY
18
S
NLR
RHR
3070
SWH
M
SP
LH
3070
CC
NLHM
HM 1-3/4"
707
CR
STY
18
S
NLR
LHR
3070
SWH
M
SP
RH
10480
**
OC
10480
**
OC
10480
**
OC
10480
**
OC
CC
FPHM
3070
SWH
M
SP
Stair 230 from Urological Associates 221
240
G1
T1
T2
1
01B.1 01B
90Min
Stair 240 from Corridor 203
1
Exterior to/from Generator
1
Exterior to/from Trash Enclosure
1
17
17
3070
HM 1-3/4"
707
RK
STY
16
S
FP
RH
Exterior to Trash Enclosure
January 15, 2013
Page 18 of 24
RH
Weld
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
Elevation: 1 - Door Type FP
January 15, 2013
Page 19 of 24
Page: 1 of 6
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
Elevation: 4 - Door Type FL 3080
24"
6"
78"
6"
6"
12"
Stile & Rail Door
January 15, 2013
Page 20 of 24
Page: 2 of 6
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
Elevation: 3 - Door Type FL 3680
30"
6"
78"
6"
6"
12"
Stile & Rail Door
January 15, 2013
Page 21 of 24
Page: 3 of 6
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
Elevation: 5 - Door Type HL
24"
6"
42"
6"
6"
36"
Stile & Rail Door
January 15, 2013
Page 22 of 24
Page: 4 of 6
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
Elevation: 2 - Door Type NL
7"
4" 10"
42"
35"
Tempered, or Firelite
Plus at rated doors
January 15, 2013
Page 23 of 24
Page: 5 of 6
CANYON VIEW MEDICAL PLAZA
Grand Junction, Colorado
Elevation: 6 - Door Type NL Rated
17"
4" 10"
25"
Tempered, or Firelite
Plus at rated doors
42"
Clarify why this lite is
required to be smaller than
standard lite at rated doors.
January 15, 2013
Page 24 of 24
Page: 6 of 6
'6--.035*4&#&"3*/()*/(&4
1-800-346-7707
www.mckinneyhinge.com
'JWF,OVDLMF4UBOEBSE8FJHIU4FSJFT
Recommended for standard weight, medium frequency doors, or doors with closing devices.
r 6TFGPSDPNNPOáVTIEPPSGSBNFXBMMBQQMJDBUJPOT
r 'PS#FWFMFE&EHFXIFSFEPPSTBSFCFWFMFEPOIJOHF
TJEFTQFDJGZ5"1PS5"14
r 'PSBWBJMBCMFàOJTIFTTFFQBHF
No.
ANSI Cross Reference
Base Material
Weight
TA2314
A5112
4UBJOMFTT
45%
TA2314
A2112
#SBTT
45%
TA2714
A8112
4UFFM
45%
"QQMJDBUJPO
Specifications
Fasteners
Gauge
No. of
Holes
3 ⁄2Y ⁄2 Y
123
6
1
Y
101Y101
130
8
1
41⁄2Y
11Y101
134
8
1
41⁄2Y1⁄2
11Y11
134
8
1
Y1⁄2
1Y11
146
8
1
Y
1Y127
146
8
1
Y
1Y1
160
10
1
Inches
1
mm
1
/PUBWBJMBCMFJO#SBTTCBTFNBUFSJBM
FM-10
TA2314
TA2714
Machine
Wood
⁄2Y10-24
1Y10
⁄2Y12-24
11⁄4Y12
⁄2Y12-24
11⁄4Y12
⁄2Y12-24
11⁄4Y12
⁄2Y12-24
11⁄4Y12
Options:
⁄2Y12-24
11⁄4Y12
Code
Description
⁄2Y ⁄4 -20
1 ⁄2Y14
NRP
/PO3FNPWBCMF1JO
TB
#BMM#FBSJOH
TCA
$PODFBMFE#FBSJOH
RC
3PVOE$PSOFS1⁄4
SBEJVTGVSOJTIFEVOMFTT
TQFDJàFEPUIFSXJTF
HT
)PTQJUBM5JQ
BT
#BMM5JQ
ST
4UFFQMF5JQ
SSF
4BGFUZ4UVE'FBUVSF
QC
&MFDUSP-ZOY ® Hinge - 2,
4, 6, 8, 1PS1XJSF
BWBJMBCMF
CC
$PODFBMFE$JSDVJU
4, 6, 8, 1PS1XJSF
BWBJMBCMF
CC-18
$PODFBMFE$JSDVJU
PS1XJSFBWBJMBCMF
1"8(XJSFTBOE
UIFSFNBJOEFS"8(
XJSFT
MM
.BHOFUJD.POJUPSJOH
1
1
Copyright © 2012, McKinney Products Company, an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of McKinney Products Company is prohibited.
astragals and meeting stiles
800-824-3018
www.pemko.com
“T” and Overlapping Astragals
359_
356_V
355_S
AVAILABLE FINISHES:
A, B, BDG, DW
AVAILABLE FINISHES:
A, BDG, D, PW, SN
AVAILABLE FINISHES:
B, BDG, C, D, G, PW, SN
•Countersinkdrillingwith
countersunk flathead screws
also available upon request at
no extra charge
Alternate Inserts
For 355
355_ V
AVAILABLE
FINISHES:
B, BDG, C, D,
G, PW, SN
355_ P
AVAILABLE
FINISHES:
B, BDG, C, D,
G, PW, SN
357_
357_ND
375_R
AVAILABLE FINISHES:
B, C, D, G
AVAILABLE FINISHES:
C, D, G, SP, SS (#4 Finish & #4 Edge)
•“ ND”denotes“nodrill”(unless
specified “ND”, astragals are drilled)
•Standardfasteneris#10 x 1" Truss
Head SMS
standard
fastener
357_ with S88
352_R
AVAILABLE FINISHES:
SP, SS (#4 Finish & #4 Edge)
AVAILABLE FINISHES:
C, D, G
•1⁄4"- 20 machine screws and thru-bolts must be
ordered separately at additional cost
•Standardfasteneris#10 x 1" Truss Head SMS
•S88(seeAdhesiveGasketingsection)must
be ordered separately at an additional cost,
if required
For reverse bevel doors
with optional fastener
and optional S88
AM-6
AVAILABLE FINISHES FOR PRODUCTS SHOWN ON THIS PAGE (see General Information section for finish chart)
A (Mill Finish Aluminum) B (Mill Finish Extruded Bronze [Brass]) BDG (Bright Dip Gold Anodized) C (Clear Anodized) D (Dark Bronze Anodized) G (Gold Anodized)
PW (Painted White) SN (Satin Nickel Anodized) SP (Galvannealed Steel) SS (See Individual Part) Special finishes available upon request
Copyright © 2012, Pemko Manufacturing Co., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Pemko Manufacturing Co. is prohibited.
800-824-3018
www.pemko.com
PK52_
P50_
MAG349_
AVAILABLE FINISHES: BL, W
AVAILABLE LENGTHS: 18', 20', 300'
AVAILABLE FINISHES: BL, W
AVAILABLE LENGTHS: 17', 25', 250'
AVAILABLE FINISHES: D, W
AVAILABLE LENGTHS: 37", 85", 96", 121"
• Minimum space between the door face
and the stop is 1⁄16"; maximum space is 3⁄8"
• Minimum space between the door face
and the stop is 1⁄16"; maximum space is
5
⁄16". Available in 17' or 25' packaged coils
• Minimum space between the door face and
the stop is 3⁄8 "; maximum space is 7⁄16"
• Positive Pressure rated up to 20 minutes
• Thermoplastic elastomer formulation
will not transmigrate; remains flexible
to -60° F
• Magnetic kerf-in weatherstrip features a
magnetic strip encased by a UV-stable
TPE cover
• Use for steel-faced door and wood frame
applications
perimeter gasketing
Kerf-In Weatherstrip (Cont.)
• Can be trimmed in the field and
corner-mitered
Magnetic Gasketing
2815_M
AVAILABLE FINISHES: C, D, G
Adhesive Perimeter Gasketing
For more information on these perimeter gasketing
products, please see the Adhesive Gasketing section.
S773_
S88_
S44_
AVAILABLE FINISHES: BL, D, GR, W
AVAILABLE LENGTHS: 17', 18', 20', 21', 25',
30', 250'
AVAILABLE FINISHES: BL, C, D, GR, TAN, W
AVAILABLE LENGTHS: 17', 18', 20', 21', 25', 30',
204', 510'
AVAILABLE FINISHES: BL, D, GR, W
AVAILABLE LENGTHS: 17', 18', 20', 21', 25',
30', 510'
•Triple-findesigneffectivelyblockslight
and sound from infiltrating a room
•Productdesignedashospitalitygasketing
(see more hospitality products in the
Hospitality Products section)
•Sealbeginscompressingat1⁄4"; compresses
to seal up to a 1⁄16" gap
•Designedfortighterframes.
•Demonstratesextremelylowclosingforce.
•Sealbeginscompressingat5⁄16"; compresses
to seal up to a 1⁄16" gap
AVAILABLE FINISHES FOR PRODUCTS SHOWN ON THIS PAGE (see General Information section for finish chart)
BL (Black) C (Black) D (Dark Brown) W (White)
Adhesive Corner Pad Colors: blank (Black Pad) W (White Pad)
Metal: C (Clear Anod) D (Dark Brown Anod) G (Gold Anod)
Copyright © 2012, Pemko Manufacturing Co., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Pemko Manufacturing Co. is prohibited.
PG-9
perimeter gasketing
800-824-3018
www.pemko.com
Standard Perimeter Gasketing
• Rigid jamb weatherstrip shown mounted on openings
with 1⁄16" gaps; however, each weatherstrip can seal gaps
up to the depth of its seal. Seal depth provided on each
illustration (example: the 303 has a 1⁄4" seal; therefore, it
can seal up to a 1⁄4" gap)
• Punched on 6" centers with slotted holes for adjustment
• Stainless steel fasteners are standard
• Other fasteners are available
• Models 294, 303, and 306 are available with self-adhesive
two-sided tape (TST) and tek screws (3 slotted holes
per part) for easy installation. To obtain this option, add
“TST” to the end of the part when ordering (example:
303AVTST)
303_S
303_PK
AVAILABLE FINISHES:
A, BDG, C, D, G, PW, SN
AVAILABLE FINISHES:
A, BDG, C, D, G, PW, SN
AVAILABLE FINISHES:
A, BDG, C, D, G, PW, SN
316_S
316_PK
316_V
AVAILABLE FINISHES:
A, BDG, D, G
AVAILABLE FINISHES:
A, BDG, D, G
AVAILABLE FINISHES:
A, BDG, D, G
303_V
13
16
(20.6)
297_S
297_PK
297_V
AVAILABLE FINISHES:
A, BDG, D, G, PW, SN
AVAILABLE FINISHES:
A, BDG, D, G, PW, SN
AVAILABLE FINISHES:
A, BDG, D, G, PW, SN
306_Q
306_V
AVAILABLE FINISHES:
A, D, PW
AVAILABLE FINISHES:
A, BDG, D, G, PW, SN
Minimum space between the door face and
the stop is 3⁄16"; maximum space is 5⁄16"
NOTE: Products shown in this section may not be drawn to scale.
PG-2
AVAILABLE FINISHES FOR PRODUCTS SHOWN ON THIS PAGE (see General Information section for finish chart)
A (Mill Finish Aluminum) BDG (Bright Dip Gold Anodized) C (Clear Anodized) D (Dark Bronze Anodized) G (Gold Anodized) PW (Painted White)
SN (Satin Nickel Anodized)
Copyright © 2012, Pemko Manufacturing Co., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Pemko Manufacturing Co. is prohibited.
800-824-3018
www.pemko.com
434_NBL
434_RL
AVAILABLE FINISH: A
AVAILABLE FINISH: A
Alternate Inserts For 434
434_PKL
AVAILABLE FINISH: A
door bottoms
Automatic Door Bottoms - Full-Mortise Models
PemkoPrene™
(PK)
EPDM (R)
nylon brush (NB)
411_NBL
411_RL
Alternate Inserts For 411
AVAILABLE FINISH: A
AVAILABLE FINISH: A
411_PKL
AVAILABLE FINISH: A
PemkoPrene™
(PK)
411_SL
AVAILABLE FINISHES: A
sponge neoprene (R)
nylon brush (NB)
sponge silicone (S)
420_PKL
AVAILABLE FINISH: A
For hollow metal doors.
Maximum drop is 1⁄2"
Alternate Inserts For 420
420_VL
AVAILABLE FINISH: A
Vinyl products
are not BHMA certified
420_SL
PemkoPrene™ (R)
AVAILABLE FINISH: A
NOTE: Products shown in this section may not be drawn to scale.
AVAILABLE FINISHES FOR PRODUCTS SHOWN ON THIS PAGE (see General Information section for finish chart)
A (Mill Finish Aluminum)
Copyright © 2012, Pemko Manufacturing Co., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Pemko Manufacturing Co. is prohibited.
DB-5
door bottoms
800-824-3018
www.pemko.com
Door Bottom Sweeps
368_N
315_N
3151_N
AVAILABLE FINISHES:
B, C, D, G, PW, SN
AVAILABLE FINISHES:
C, D, G
Finished product
supplied with
BLACK insert.
GRAy available
upon request.
AVAILABLE FINISHES:
C, D, G
321_N
AVAILABLE FINISHES:
C, D, G
1
(31.8)
1
(25.4)
56_V
57_V
99_V
307_V
AVAILABLE FINISHES:
A, BDG, D, G, PW, SN
AVAILABLE FINISHES:
A, BDG, D, G, PW, SN
AVAILABLE FINISHES:
PA, PD, PG, PW
AVAILABLE FINISHES:
A, BDG, C, D, G, PW, SN
308_V
309_P
345_
345_V
AVAILABLE FINISHES:
A, BDG, C, D, G, PW, SN
AVAILABLE FINISHES:
A, BDG, D, G, PW, SN
AVAILABLE FINISHES:
A, B, BDG, C, D, G, PW
AVAILABLE FINISHES:
A, BDG, C, D, G, PW
NOTE: Products shown in this section may not be drawn to scale.
DB-12
AVAILABLE FINISHES FOR PRODUCTS SHOWN ON THIS PAGE (see General Information section for finish chart)
A (Mill Finish Aluminum) B (Mill Finish Extruded Bronze [Brass]) BDG (Bright Dip Clear Anodized) C (Clear Anodized) D (Dark Bronze Anodized) G (Gold Anodized)
PD (Painted Dark Bronze) PG (Painted Gold) PW (Painted White) SN (Satin Nickel Anodized)
Copyright © 2012, Pemko Manufacturing Co., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Pemko Manufacturing Co. is prohibited.
800-824-3018
www.pemko.com
2746x6_
AVAILABLE FINISHES: A, D, G
Welded on bottom.
274x4_
AVAILABLE FINISH: A, B, D, G
Welded on bottom.
commercial thresholds
Saddle Thresholds (Cont.)
2749_
AVAILABLE FINISHES: A, D, G
2750_
AVAILABLE FINISHES: A, D, G
Includes two support legs (only one shown due to break in drawing)
1665_
AVAILABLE FINISHES: A, D, G
169_
AVAILABLE FINISHES: A, D, G
170_
AVAILABLE FINISHES: A, B, BDG, D, G
1700_
AVAILABLE FINISHES: A, D
NOTE: Products shown in this section may not be drawn to scale.
AVAILABLE FINISHES FOR PRODUCTS SHOWN ON THIS PAGE (see General Information section for finish chart)
A (Mill Finish Aluminum) B (Mill Finish Extruded Bronze [Brass]) BDG (Bright Dip Gold Anodized) D (Dark Bronze Anodized) G (Gold Anodized)
NOTE: G is available with limited inventory
Copyright © 2012, Pemko Manufacturing Co., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Pemko Manufacturing Co. is prohibited.
CT-3
flush bolts
800-458-2424
www.rockwoodmfg.com
Lever Extension Flush Bolt
No. 555
Material:
Brass.
Finishes:
Available in standard architectural finishes (see page 9).
Fastener:
8 ea. #8 x 3⁄4" FH combo screws.
Features:
• For Fire Rated Hollow Metal Swinging Doors measuring up to 4'w x 10'h
rated up to and including 3 Hours.
• Fits ANSI A115 door and frame preparation.
• 3⁄4" bolt throw, 3⁄4" rod backset.
• 12" rod length (center of face to bolt end - retracted).
• 11⁄2" adjustable bolt head.
No.
Size
Weight
ANSI A156.16
555
Face plate: 1" x 63⁄4"
Strike: 15⁄16" x 21⁄4"
Guide: 1" x 2"
1.5 lbs./2
L04251
Lever Extension Flush Bolt with Bottom Fire Bolt
No. 555 x 18BFB
Material:
Flush bolt - brass.
Bottom fire bolt - stainless steel.
Finishes:
Available in standard architectural finishes (see page 9).
Fastener:
8 ea. #8 x 3⁄4" FH combo screws.
Features:
• For Fire Rated Hollow Metal Swinging Doors measuring up to 4'w x 9'h
rated up to and including 3 Hours.
• Fits ANSI A115 door and frame preparation.
• 3⁄4" bolt throw, 3⁄4" rod backset.
• 12" rod length (center of face to bolt end - retracted).
• 11⁄2" adjustable bolt head.
• When door is subjected to 230˚F the plug and black plastic cover will
melt allowing the bolt to project, locking the leaves together.
• Bottom fire bolt eliminates need for floor prep.
• Oversize fire bolt strike hole allows for slight door misalignment.
E2
No.
Size
Weight
555 x 18BFB
Top bolt: 1" x 63⁄4"
Bottom bolt: 13⁄16" dia.
0.9 lbs.
Copyright © 2012, Rockwood Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction
in whole or in part without the express written permission of Rockwood Manufacturing Company is prohibited.
door pulls
800-458-2424
www.rockwoodmfg.com
Door Pulls No. 102, 105, 106, 107, 108, 109
Material:
Aluminum, brass, bronze, stainless steel.
Finishes:
Available in standard architectural finishes, US32DMS, US32D316,
US32316, white (WPC), red (RPC), and black (BPC) powder coat finishes
(see page 9). *US3LIFETIME available on select product below.
Fastener:
1
Options:
• Back to back mounting in pairs — use BTB suffix and mounting type
number (107BTB5).
⁄4 - 20 x 21⁄4" thru bolt & finish washer (standard 13⁄4" door).
• Concealed mounting single pulls — use C suffix and mounting type
number (107C6).
• Advise if door thickness is other than 13⁄4".
• See page B13 for mounting selection (standard duty 1⁄4 - 20).
• 21⁄2" Barrier Free clearance — use BF prefix (BF107).
No.
Material Size
CTC
Overall
Base
Projection
Clearance
Weight
ANSI A156.6
102
5
⁄8" dia.
1
5 ⁄2"
6 ⁄8 "
5
⁄8 "
2"
3
1 ⁄8"
0.6 lbs.
—
105
3⁄4" dia.
1
5 ⁄2"
1
6 ⁄4"
3⁄4"
1
2 ⁄4"
1
1 ⁄2"
1.2 lbs.
J401
106
3⁄4" dia.
6"
63⁄4"
3⁄4"
1
2 ⁄4"
1
1 ⁄2"
1.3 lbs.
J401
107*
3⁄4" dia.
8"
83⁄4"
3⁄4"
1
2 ⁄4 "
1
1 ⁄2"
1.6 lbs.
J401
108
3⁄4" dia.
10"
103⁄4"
3⁄4"
1
2 ⁄4"
1
1 ⁄2"
1.8 lbs.
J401
109
3⁄4" dia.
12"
123⁄4"
3⁄4"
21⁄4"
11⁄2"
2.1 lbs.
J401
1
Door Pulls No. 110, 111A, 111, 112, 118
Material:
Aluminum, brass, bronze, stainless steel.
Finishes:
Available in standard architectural finishes, US32DMS, US32D316,
US32316, white (WPC), red (RPC), and black (BPC) powder coat finishes
(see page 9). *US3LIFETIME available on select product below.
Fastener:
1
Options:
• Back to back mounting in pairs — use BTB suffix and mounting type
number (112BTB5).
⁄4 - 20 x 21⁄4" thru bolt & finish washer (standard 13⁄4" door).
• Concealed mounting single pulls — use C suffix and mounting type
number (112C6).
• Advise if door thickness is other than 13⁄4".
• Heavy duty versions of most fastening types available - use suffix HD to
fastening type number (112BTB5HD).
• See page B13 for mounting selection (standard duty 1⁄4 - 20).
• 21⁄2" Barrier Free clearance — use BF prefix (BF110).
B14
No.
Material Size
CTC
Overall
Base
Projection
Clearance
Weight
ANSI A156.6
110
1" dia.
8"
9"
1"
3"
2"
3.0 lbs.
J401
111A
1" dia.
9"
10"
1"
3"
2"
3.3 lbs.
J401
111*
1" dia.
10"
11"
1"
3"
2"
3.5 lbs.
J401
112*
1" dia.
12"
13"
1"
3"
2"
4.0 lbs.
J401
118
1" dia.
18"
19"
1"
3"
2"
5.4 lbs.
J401
Copyright © 2012, Rockwood Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction
in whole or in part without the express written permission of Rockwood Manufacturing Company is prohibited.
push plates
800-458-2424
www.rockwoodmfg.com
Push Plates - .050" Thick
Material:
Aluminum, brass, bronze, stainless steel.
Finishes:
Available in standard architectural finishes, US32DMS, US32D316, US32316, and US3LIFETIME (see page 9).
Fastener:
#6 x 5⁄8" OH SMS.
Features:
Four beveled edges.
Ordering:
S pecify plate number followed by size designation and finish (70B US32D) or for non-standard size 70.
Specify width x height and finish. Specify any additional options.
Options:
• Custom sizes available upon request.
• TEK - self-drilling screws.
• TORX - security Torx screws.
• SA - self-adhesive mounting: 1⁄16" double face foam tape (no screw holes on plate).
• Engraving on plates 4" wide or wider. Specify copy. See page B1 for standard engraving locations.
• Cylinder cutouts (CFC) and turn knob cutouts (CFTT). See page B1 for standard locations and sizes.
No. 70
No.
Standard Size
Weight
ANSI A156.6
70A
3" x 12"
0.7 lbs.
J301
70B
31⁄2" x 15"
0.9 lbs.
J301
70C
4" x 16"
1.0 lbs.
J301
70E
6" x 16"
1.5 lbs.
J301
70F
8" x 16"
2.0 lbs.
J301
70G
4" x 20"
1.3 lbs.
J301
No.
Standard Size
Weight
ANSI A156.6
70RCA
3" x 12"
0.7 lbs.
J301
70RCB
31⁄2" x 15"
0.9 lbs.
J301
70RCC
4" x 16"
1.0 lbs.
J301
70RCE
6" x 16"
1.5 lbs.
J301
70RCF
8" x 16"
2.0 lbs.
J301
70RCG
4" x 20"
1.3 lbs.
J301
No.
Standard Size
Weight
ANSI A156.6
70REA
3" x 12"
0.7 lbs.
J301
70REB
31⁄2" x 15"
0.9 lbs.
J301
70REC
4" x 16"
1.0 lbs.
J301
No. 70RC
No. 70RE
B2
Copyright © 2012, Rockwood Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction
in whole or in part without the express written permission of Rockwood Manufacturing Company is prohibited.
800-458-2424
www.rockwoodmfg.com
door plates
Mop Plate
Kick Plate
Stretcher Plate
Armor Plate
Up to 6" h x 48" w
6" to 12" h x 48" w
6" to 12" h and up to 48" w
Up to 48" h x 48" w and
available in most finishes
Width of Plates:
Push Side: 2" less than door width. Pull Side: 11⁄2" less than door width.
OPTIONAL
NFPA 80 STANDARDS — 2-4.5 Protection Plates: Factory-installed protection plates shall
be installed in accordance with the listing of the door. Field-installed protection plates shall be
labeled and installed in accordance with their listing.
Self-Drilling TEK
Screws
Exception: Labeling is not required where the top of the protection plate is not more than 16 in.
(406 mm) above the bottom of the door.
Cuts door plate installation
time in half.
Metal Door Plate - Economy Duty No. K1038
Material:
.038" aluminum, stainless steel.
Finishes:
Brass look aluminum (BRS LK), US32D, and US3LIFETIME.
Fastener:
#6 x 5⁄8" OH SMS.
Ordering:
Specify height x width x finish code. Add any options.
Weight:
8" x 34" = 3.2 lbs.
Options:
• SA - self-adhesive mounting.
• TORX - security Torx screws.
• TEK - self-drilling screws.
• Cutouts for locks, louvers, or windows (see worksheets on pages C14-C15 for details on how to order).
Metal Door Plate - Standard Duty No. K1050, K1050F
Material:
.050" aluminum, brass, bronze, stainless steel.
Finishes:
Available in standard architectural finishes, US32DMS, US32D316, and US32316 (see page 9).
Fastener:
#6 x 5⁄8" OH SMS.
Ordering:
Specify height x width x finish code. Add any options.
Weight:
8" x 34" = 4.0 lbs.
ANSI:
J101 - metal armor plate, J102 - metal kick plate, J103 - metal stretcher & mop plate.
Options:
• SA - self-adhesive mounting.
See hardware schedule for required sizes
• TEK - self-drilling screws.
• Beveled 3 or 4 edges, specify B3E or B4E.
• Cutouts for locks, louvers, or windows
(see worksheets on pages C14-C15 for details on
how to order).
• Screw mounting (K1050F) and UL listed for use
on 90-minute label wood doors and 3-hour label
metal doors.
• CSK - countersunk holes.
• TORX - security Torx screws.
C1
Copyright © 2012, Rockwood Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction
in whole or in part without the express written permission of Rockwood Manufacturing Company is prohibited.
dome stops
800-458-2424
www.rockwoodmfg.com
Low Dome Stops No. 440, 441
Material:
Solid cast brass with DuraFlex bumper.
Finishes:
Available in standard architectural finishes (see page 9).
Other:
No. 441 is packed with both WS and MS fasteners.
Features:
For doors without thresholds (not undercut).
Options:
Exterior pack screw packs, stainless steel plated to match — use EXP suffix
(440 x EXP) when ordering.
No.
Fastener
Base
440
#12 x 1 ⁄4" fh ws, plastic anchor
1
441
#12 x 1 ⁄2" fh ws, plastic anchor;
#12 - 24 x 1" FH MS, lead anchor
1
1
1
Height
Weight
ANSI A156.16
⁄4" h x 1 ⁄8" dia.
1
1 ⁄8"
2.1 lbs./10
L02141
⁄4" h x 1 ⁄8" dia.
1 ⁄8"
2.5 lbs./10
L02141
7
7
1
Dome Stop Combination Unit No. 441CU
Material:
Solid cast brass with DuraFlex bumper.
Finishes:
Available in standard architectural finishes (see page 9).
Other:
Set consists of 1 each No. 441 and 1 each No. 444. For use at doors with
or without a threshold.
Features:
Convertible for undercut or not undercut doors.
Options:
Exterior pack screw packs, stainless steel plated to match — use EXP suffix
(441CU x EXP) when ordering.
No.
Fastener
Base
441CU
#12 x 1 ⁄2" fh wS, plastic anchor;
#12 - 24 x 11⁄2" FH MS, lead anchor
Dome stop: ⁄4" h x 1 ⁄8" dia.
Riser: 3⁄8" h x 2" dia.
444
Cast riser only
3
1
Height
1
⁄8" h x 17⁄8" dia.
7
Weight
ANSI A156.16
1 ⁄8" or 1 ⁄2"
3 lbs./10
L02141/
L02161
⁄8"
10 ozs./10
L02141
1
1
3
Cast Universal Dome Stop No. 441H
Material:
Solid cast brass with DuraFlex bumper.
Finishes:
Available in standard architectural finishes (see page 9).
Features:
Low lip dome stop with height of high dome stop, eliminates the need to
determine requirement for traditional low or high dome stop – one stop
for all applications. Integral cast pin for added strength. Universal screw
pack included for all floor conditions.
Options:
Exterior pack screw packs, stainless steel plated to match — use EXP suffix
(441H x EXP) when ordering.
No.
Fastener
Base
Height
Weight
ANSI A156.16
441H
#12 x 11⁄4" FH WS, plastic anchor
7
⁄32" h x 17⁄8" dia.
111⁄16"
3.2 lbs./10
L02141
#12 - 24 x 1" FH MS, lead anchor
D4
L02161
Copyright © 2012, Rockwood Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction
in whole or in part without the express written permission of Rockwood Manufacturing Company is prohibited.
wall stops
800-458-2424
www.rockwoodmfg.com
Solid Cast Wall Stop No. 416
Material:
Cast brass with DuraFlex bumper.
Finishes:
Available in standard architectural finishes (see page 9).
Features:
For use where concealed mounting is not desired. School version.
Options:
Tamperproof Torx screws.
No.
Bumper
Fastener
Size
Projection
Weight
ANSI A156.16
416
Concave
#8 x 13⁄4" FH SMS
2 ⁄16" dia.
1"
3.5 lbs./10
L12261
7
Wrought Wall Stops No. 406
Material:
Wrought brass, bronze, and stainless steel with DuraFlex bumper.
Finishes:
Available in standard architectural finishes (see page 9).
Features:
Concealed mounting, convex bumper. Back plate prevents damage
to wall.
No.
Bumper
Fastener
Size
Projection
Weight
ANSI A156.16
406
Convex
#8 x 11⁄4" TH SMS, plastic toggle
21⁄2" dia.
3⁄4"
1.8 lbs./10
L02101
Wrought Wall Stops No. 409
D2
Material:
Wrought brass, bronze, and stainless steel with DuraFlex bumper.
Finishes:
Available in standard architectural finishes (see page 9).
Features:
Concealed mounting, concave bumper. Back plate prevents damage
to wall.
Options:
DuraFlex bumper available in standard gray or optional black.
No.
Bumper
Fastener
Size
Projection
Weight
ANSI A156.16
409
Concave
#8 x 11⁄4" TH SMS, plastic toggle
21⁄2" dia.
3⁄4"
1.8 lbs./10
L02251
Copyright © 2012, Rockwood Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction
in whole or in part without the express written permission of Rockwood Manufacturing Company is prohibited.
flush bolts , strikes and coordinators
800-458-2424
www.rockwoodmfg.com
Lever Extension Flush Bolt With Bottom Fire Bolt
No. 557 x 19BFB
Material:
Flush bolt - brass.
Bottom fire bolt - stainless steel.
Finishes:
Available in standard architectural finishes (see page 9).
Fastener:
7 ea. #8 x 3⁄4" FH combo screws.
4 ea. #8 - 32 x 1⁄2" FH MS.
4 ea. #8 counter sunk washer.
Features:
• F or Fire Rated Plastic & Wood Covered Fire Doors measuring up to 4'w
x 9'h rated up to 20 minutes.
• 3⁄4" bolt throw, 3⁄4" backset; door strength maintained by corner
reinforcing plate.
• When door is subjected to 230˚F the plug and black plastic cover will
melt allowing the bolt to project, locking the leaves together.
• Bottom fire bolt eliminates need for floor prep.
• Oversize fire bolt strike hole allows for slight door misalignment.
Size
Weight
No.
557 x 19BFB
Top bolt: 1" x 63⁄4"
Bottom bolt: 13⁄16" dia.
0.9 lbs.
Dust Proof Strike No. 570
Material:
Brass.
Finishes:
Available in standard architectural finishes (see page 9).
Fastener:
Adjustment nut.
Spanner wrench.
2 ea. #8 x 1 OH SMS, 2 ea. plastic anchors.
2 ea. #8 - 32 x 3⁄4" OH MS, 2 ea. lead anchors.
Features:
• Works with all Rockwood manual and automatic flush bolts.
• Removable face plate for use with thresholds.
• Adjustable height for carpeted areas.
No.
Size
570
Face plate: 1 ⁄8" x 2 ⁄8"
Barrel: 7⁄8" dia. x 2" depth
3
7
Weight
ANSI A156.16
0.4 lbs.
L04021
Gravity Door Coordinator No. 576
Material:
Cast brass.
Finishes:
Available in standard architectural finishes (see page 9).
Fastener:
Body: 2 ea. #10 x 1" FH SMS, 2 ea. #10 - 24 x 1" FH MS.
Strike: 5 ea. #8 x 1" FH SMS.
Other:
• For use on door sizes:
- with Astragal on active door - 18" to 48".
- with Astragal on inactive door - 18" to 34".
- with Astragal on both doors - 18" to 30".
•T
he overlap of the astragal is maximum 7⁄8" with door hung on standard
hinges. Customer must contact the factory for all other astragal
situations.
Features:
E4
Non-handed reversible. Prevents the active door from closing until the
inactive door is closed.
No.
Size
576
1" x 5 ⁄16"
7
Projection
Weight
ANSI A156.3
7"
2.2 lbs.
Type 21
Copyright © 2012, Rockwood Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction
in whole or in part without the express written permission of Rockwood Manufacturing Company is prohibited.
silencers
800-458-2424
www.rockwoodmfg.com
door guards
&
Wall Guard No. 606
Material:
Clear rubber.
Other:
Sold in sheets of 55­.
Features:
Self-adhesive mounting.
No.
Fastener
Size
Weight
606
Self-adhesive back
1" x 1"
0.4 lbs./55
Privacy Door Latch No. 607
Material:
Zinc die cast.
Finishes:
BRS, DBRS, STNN, CRM, DCRM, ORB.
Features:
• ADA compliant.
• Enhanced in room privacy.
• Easy to install.
• F or use with UL Classified fire doors for use with hollow metal
steel composite type fire doors rated up to and including 3 hrs.
Wood composite type fire doors rated up to and including 11⁄2 hrs
and 20 minutes without hose stream.
No.
Fastener
Size
Weight
607
#12 x 11⁄4" FH SMS
11⁄2" x 2 ⁄16"
0.75 lbs.
13
Door Silencer No. 608CA
608
609
E10
Material:
Clear rubber.
Other:
Sold in packages of 300.
Features:
Self-adhesive mounting.
No.
Fastener
Size
Weight
608CA
3
⁄8" dia. x ⁄8"
Metal or wood
0.2 lbs./300
1
Door Silencers No. 608, 609
Material:
DuraFlex gray rubber.
Other:
Sold in packages of 100.
No.
Size
Frame Type
Weight
ANSI A156.16
608
1⁄2" dia. x 5⁄8"
Metal
1.3 lbs./500
L03011
609
3
⁄8" x 3⁄4"
Wood
1.3 lbs./500
L03021
Copyright © 2012, Rockwood Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction
in whole or in part without the express written permission of Rockwood Manufacturing Company is prohibited.
Table of Contents
10 Line Cylindrical Lever Locks
Features, Benefits & Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Lever & Rose Designs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Electromechanical Functions & Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Strikes & Finishes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Mechanical & Cylinder Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
How to Order, Packaging, Architectural Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Windstorm Certifications: UL Certifications & Florida Building Codes . . . . . . . . . . . . . . 10-11
As part of their promise to provide innovative, fast and effective
high security solutions to their customers, ASSA ABLOY Group
companies offer ElectroLynx®, a universal quick-connect system
that simplifies the electrification of the door opening.
ElectroLynx® is a registered trademark of ASSA ABLOY Inc.
Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
90144:C 08/01/11
Copyright © 2004-2009, 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Specifications
For Doors1-3/4" (44mm) thick door adjusts to 2" (51mm) standard
1-3/8" (35mm) thick door, 1- Option for Adapter plates
Backsets2-3/4" (70mm) backset w/ 1-1/8" front (standard)
2-3/8" (60mm) backset w/ 1" wide front (specify 20-)
3-3/4" (95mm) backset w/ 1-1/8" front (specify 23-)
5" (127mm) backset w/ 1-1/8" Front (specify 25-)
Cylindrical Housing
Steel, zinc dichromate finish
FrontWrought brass, bronze and stainless steel
2-1/4" (57mm) x 1-1/8" (29mm) Fixed Bevel
2-1/4" (57mm) x 1" (25mm) (included with 20-)
Strike
Wrought brass, bronze and stainless steel
800 curved lip strike – standard
808 curved lip ANSI strike (28- option)
Wrought box strike available (WBS- option)
HandAll 10 Line Locks are non-handed except for the G & Y Levers
Roses
Heavy wrought brass and bronze
Latch
Stainless steel 1/2" (13mm) throw
Brass 3/4" (19mm) throw for pairs of doors (41- option)
Cylinder
Brass, 6 pin, LA keyway standard
Keys
Two, nickel silver
Masterkeying
Can be master keyed or grand master keyed Construction key
systems available
Finishes
03, 04, 09, 10, 10B, 10BL, 14, 15, 20D, 26, 26D
Options
For detailed information see “Options”
Door Prep161 Door Prep Modified
160 Door Prep Modified (specify 20-)
Minimum Stile
4-1/2" (114mm)
Certification Compliance
ANSI/BHMA
UL
Positive Pressure
ADA
California Code
Hurricane Code
Certified ANSI A156.2 Series 4000 - Grade 1
UL listed to U.S.A. and Canadian safety standards
Listed for 3 hour doors (double doors require 41 - option)
Meets UL 10C and UBC 7-2 (1997)
All levers conform to ADA requirement for barrier-free accessibility
Levers (L, J & P) conform to California Administrative Code Title 19 and 24
All individual components of a total door opening are required to comply with each code. Refer to the SARGENT Website (www.sargentlock.com)
for specific code compliance listings for both the lock hardware and other door components.
Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the
opening, and Sargent Manufacturing Company makes no representations or warranties concerning what
such impact may be in any specific situation. When retrofitting any portion of an existing fire rated opening,
or specifying and installing a new fire-rated opening, please consult with a code specialist or local code
official (Authority Having Jurisdiction) to ensure compliance with all applicable codes and ratings.
On The Cover
• 10G05 x GL
1-800-727-5477 • www.sargentlock.com
MicroShield®
As part of their promise to provide innovative solutions to
their customers, certain ASSA ABLOY Group brands offer the
MicroShield® technology, a silver-based antimicrobial coating
designed to inhibit the growth of bacteria.
MicroShield® is a registered trademark of Yale Security Inc.,
an ASSA ABLOY Group company.
MicroShield® Coating
•Revolutionary finish coating available on all SARGENT
product lines, utilizes a silver-based antimicrobial
compound from Agion Technologies
•As an integral part of the finish coating, MicroShield lasts for
the life of the hardware
•MicroShield coating permanently suppresses the growth
of bacteria, algae, fungus, mold and mildew. It is effective
against a broad spectrum of bacteria.
•Non-toxic and completely safe. The Agion antimicrobial
compound is EPA and NSF approved and FDA listed for use
in medical and food preparation equipment.
•Applications: Anywhere there is need for a clean
environment (hospitals, laboratories, schools, medical
centers, daycare, food processing etc.)
Features & Benefits
10 Line Cylindrical Lever Locks
Features & Benefits
A heavy duty cylindrical key-in-lever lock designed to exceed the requirements of ANSI 156.2 Series 4000 Grade 1. The 10 Line is the standard for
institutional applications such as medical, educational and municipal facilities.
Multiple through-bolt positions
Solid cast levers
Accommodates doors 1-3/4" to 2" thick
Self-tapping screws
Retained through-bolt screws
Manufactured with pride
in New Haven, CT USA
Multiple key systems
Strength, Durability and Security
Flexibility
Applications
• C
ycle Test: Exceeds 5 times A156.2 Grade 1 requirements
• Abusive Locked Lever Torque- without entry gained: Exceeds 1.5 times A156.2 Grade 1 requirements
• 7 YEAR LIMITED WARRANTY – no service required to maintain warranty
• Fits a variety of door preparations with adaptable through-bolt positioning
• Accommodates retrofit applications with optional
2-3/8", 3-3/4" and 5" backset latches
• 6 ADA lever styles to complement a wide array of design applications
• Levers (B, L, J & P) are non-handed for efficient warehousing and for ease of installation
• 11 Architectural grade finishes
• 21 Functions
• SARGENT uses engineered solutions and flexible manufacturing processes to accommodate special applications
• D
esigned to conform to national & state fire and handicapped requirements
• Grade 1 Lock
• Heavy duty commercial and institutional
interior and exterior doors
• Offices
• Schools/Universities
• Hospitals
• Manufacturing facilities
Convenience
• Installs in 1 minute or less
• Quickly adapts to fit multiple through-bolt positions
• User friendly packaging
• User friendly instruction sheets
• Convenient installation diagram on box
Design
• Solid feel and precise lever action
• Slim rose design available
• Decorative Levers — Coastal Series designs – Gulfport and Yarmouth
• Levers are solid one piece cast construction, except “J” lever
Security
•
•
•
•
Torx® and spanner screws optional
Classroom security and multiple locking functions available
Vandal resistant trim optional (FW- option)
Security key systems available (Signature, Keso,
BR-XC, XC)
1-800-727-5477 • www.sargentlock.com
1
Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
2-3/4" Std, 2-3/8", 3-3/4"
and 5” optional backsets
90144:C 08/01/11
Copyright © 2004-2009, 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Universal non-handed
Lever & Rose Designs
10 Line Cylindrical Lever Locks
B Lever Design
G Rose Design
• Lever: B–Solid Cast
• Rose G - Heavy Wrought
2-1/2"
(64mm)
5"
(129mm)
1-1/2"
(38mm)
Y Lever Design - Coastal Design - Yarmouth
L Rose Design
• Lever: Y–Solid Cast
• Handed
• Rose L - Heavy Wrought
2-1/2"
(64mm)
5-3/8"
(137mm)
1-3/4"
(38mm)
J Lever Design
• Lever: J–Wrought
5-3/8"
(137mm)
2-1/2"
(64mm)
3/8"
(10mm)
J lever – not available with Freewheeling or Interchangeable Core
L Lever Design
2-1/2"
(64mm)
5"
(127mm)
3/8"
(10mm)
P Lever Design
• Lever: P–Solid Cast
5-1/2"
(140mm)
2-1/2"
(64mm)
3/8"
(10mm)
G Lever Design - Coastal Design - Gulfport
• Lever: G–Solid Cast
• Handed
5-1/2"
(140mm)
2-1/2"
(64mm)
Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
• Lever: L–Solid Cast
90144:C 08/01/11
Copyright © 2004-2009, 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
3-1/2"
(89mm)
1-3/4"
(38mm)
NOTE: Any rose or lever on this page can be combined to suit individual taste.
NOTE: All lever height measurements represent total distance from door face.
2
1-800-727-5477 • www.sargentlock.com
3/8"
(10mm)
5/8"
(16mm)
3-1/2"
(89mm)
Functions
10 Line Cylindrical Lever Locks
Single Cylinder Functions
04 Storeroom or Closet
50 Hotel, Dormitory
or Apartment
10G04
• Deadlocking latch
10G50
• Latch by lever inside or key outside
• Latch by key outside and lever inside
• Outside lever rigid at all times
• Outside lever always rigid
• ANSI F86
• D
epressing push button when door is closed shuts out all keys except emergency key and projects visual occupancy indicator in cylinder face
05 Entrance or Office
• P
ush button released by turning inside lever
automatically reactivating all keys and retracting
visual occupancy indicator
• Deadlocking latch
• Latch by either lever unless outside lever is locked by push/turn button in inside lever
• P
ush button released by key outside or
lever inside
• Turn button must be released manually
• Key retracts latch when outside lever is locked
• ANSI F109
24 Entrance or Office
• Deadlocking latch
10G24
• Latch by either lever unless outside lever is locked by push button in inside lever
• Push button released by key or turning inside lever
• C
losing door does not unlock outside lever or release button
• K
ey in outside lever retracts latch when outside lever is locked and releases inside push button
• ANSI F82
• Push button fixed by lockout key must be released manually
• Lock out key provided
• See option page for restrictions to 50 function
• ANSI F93
54 Corridor, Dormitory
10G54
• Deadlocking latch
• Latch by either lever unless outside lever is
lockedby push buttoninside or key outside
• R
otating inside lever or closing door releases inside button only, but does not unlock the outside lever if locked by key
• K
ey outside locks or unlocks outside lever and also retracts latchbolt when locked
• ANSI F90
37 Classroom
• Deadlocking latch
10G37
• Latch by either lever unless outside lever is locked by key
• Key in outside lever locks or unlocks outside lever and retracts latch
• Inside lever always operative
• ANSI F84
44 Service Station
10G44
• Deadlocking latch
• L atch by either lever unless outside lever is locked
by push button in inside lever
• Key retracts latch when outside lever is locked
• P
ush button released by turning inside lever,
closing door, or by key in outside lever unless push
button is fixed in locked position by turning coin
slot in inside lever
• Slotted inside button must be manually released
• ANSI F92
Freewheeling Locked Lever Option
•
•
•
•
Available on all locking functions except 10G70 and 10G71
Provides protection from vandalism and added security
Stops in the rose prevent the lever from traveling beyond 60° in either direction
Not available in “J” Lever Design and some options
Note: Shaded lever indicates it is rigid at all times.
1-800-727-5477 • www.sargentlock.com
3
Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
• L ock out key fixes push button in locked position,
shutting out all keys except emergency
90144:C 08/01/11
Copyright © 2004-2009, 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
10G05
• Deadlocking latch
Functions
10 Line Cylindrical Lever Locks
Double Cylinder Functions
16 Classroom Security, Apartment, Exit, Privacy
30 Communicating
• Deadlocking latch
10G16
• Latch by either lever unless outside lever is locked by key in inside lever
10G30
• Key in outside lever retracts latch when outside lever is locked
• Inside lever always operative
• ANSI F88
17 Utility, Asylum
or Institutional
• Deadlocking latch
• Latch by either lever
• Key in either lever locks or unlocks its own lever only
• Use only on rooms with more than one exit
• ANSI F80
38 Classroom Security
10G38
• Deadlocking latch
• Latch by either lever unless outside lever is locked by key
10G17
• Deadlocking latch
• Both levers rigid at all times
• Latch by key either side
• Use only on rooms with more than one exit
• Key in either lever locks or unlocks outside lever
• ANSI F87
26 Store or Storeroom
10G26
• Inside lever always operable
• Locked indication on inside rose standard with this function
• Deadlocking latch
• Latch by either lever
• Key in either lever locks or unlocks both levers
• ANSI F91
Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
90144:C 08/01/11
Copyright © 2004-2009, 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Non-Cylinder Functions
13 Exit
68 Hospital Privacy
10G13
• Deadlocking latch
• L atch by either lever unless outside lever is locked by push button in inside lever
10U68
• Latch by inside lever
• Outside lever rigid at all times
• ANSI F89
• Turning inside lever or closing door releases button
• Rotating thumbturn in outside lever unlocks the
outside lever and releases the inside button
15 Passage
10U15
• Not available in the “J” lever design
• Latch by either lever
• ANSI F75
93Single & 94 Double
Lever Pulls
10U93/10U94
• Lever and rose both sides joined by two
through-bolts
15-3 Exit or Communicating
10G15-3
• Deadlocking latch
• Latch by lever inside
• M
inimum clearance of 1-1/8" on single doors and 2-1/4" between double doors
This pull • Requires special door preparation – see template
only for 93
• Blank rose outside
Pull
94-2 Double Lever
10U65
• Emergency button in outside lever unlocks, with use of a blade screwdriver in outside lever and releases inside button
• ANSI F76
Note: Shaded lever indicates it is rigid at all times.
4
1-800-727-5477 • www.sargentlock.com
• For wood or custom hollow metal doors
• Dummy latch plate
• L atch by either lever unless outside lever is locked
by push button in inside lever
• T
urning inside lever or closing door releases button
10U94-2
• Lever and rose both sides joined by two
through-bolts
65 Privacy/Bathroom
• For wood or custom hollow metal doors
• Uses standard door prep template
Freewheeling Locked Lever Option
•
•
•
•
Available on all locking functions except 10G70 and 10G71
Provides protection from vandalism and added security
Stops in the rose prevent the lever from traveling beyond 60° in either direction
Not available in “J” Lever Design and some options
Strikes & Finishes
10 Line Cylindrical Lever Locks
Strikes
• Finishes: 03, 04, 09, 10, 10B, 10BL, 14, 15, 20D, 32D
2-3/4" Curved Lip Strike – Standard
4-7/8" Curved Lip Strike: (28-Option)
1-1⁄4"
(32mm)
1-1⁄8"
(29mm)
1⁄16"
(2mm)
5/16" (8mm)
radius
1⁄16"
(2mm)
3/8" (10mm)
start of radius
• F urnished standard with 1-1/4" (32mm) curved lip from center of
strike screw holes to end of lip
• L ip lengths 7/8" (22mm), 1" (25mm), 1-1/4" (32mm) standard,
1-1/2" (38mm), 1-3/4" (44mm) and 2" (51mm)
• To order strike separately, specify 800 strike x finish x lip length
3-3⁄8"
(85mm)
4-7⁄8"
(124mm)
2-3⁄4"
(70mm)
1-1⁄2"
(38mm)
1-1⁄4"
(32mm)
1-1⁄4"
(32mm)
5/16" (8mm)
radius
3/8" (10mm)
start of radius
• Conforms to ANSI standard
• F urnished standard with curved lip 1-1/4" (32mm) from center of strike
screw holes to end of lip
• L ip lengths 7/8" (22mm), 1-1/8" (29mm), 1-1/4" (32mm),
1-3/8" (35mm), 1-5/8" (42mm), 1-7/8" (48mm), 2-1/8" (54mm),
2-3/8" (60mm), 2-5/8" (66mm), 2-7/8" (73mm)
Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
90144:C 08/01/11
Copyright © 2004-2009, 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
• To order strike separately, specify 808 strike x finish x lip length
Finishes
Finish
Descriptions
ANSI/BHMA
03
Polished brass, clear coated
605
04
Satin brass, clear coated
606
09
Polished bronze, clear coated
611
10
Satin bronze, clear coated
612
10B
Oxidized bronze, oil rubbed
613
10BL
Oxidized satin, bronze, clear coated
614
14
Polished nickel, clear coated
618
15
Satin nickel, clear coated
619
20D
Statuary dark bronze, clear coated
624
26
Polished chrome
625
626
26D
Satin chrome
SG- Option
MicroShield® available on all finishes except 10B (613)
Zinc levers are plated to match BHMA finish.
Split finishes available. Specify outside finish first.
Custom colors available, consult factory.
6
1-800-727-5477 • www.sargentlock.com
General Information
351 Series Powerglide®
Closer Spring Adjustment (not shown)
Door Closer Cycle
Delayed action valve (Optional)
• Holds the door in the open position
momentarily
• 20 second minimum hold open delay
• The feature is available for all applications
and arms
• Beneficial when moving carts or objects
through door opening or ADA applications
• Effects the entire cycle of the door closer
movement
• Used to size closer for application requirements
• Determines the amount of force with which
the door closes and the amount of force
required to open the door
• Adjustable to compensate for door size and
draft conditions
Closing speed valve
Backcheck valve
Opening
Cycle
• At approximately 70° of the open cycle,
the Backcheck Valve begins to slow the
door’s motion
• Prevents the door from slamming into
the door's stop
• Valve is used to control the intensity of
the Backcheck
• Note: A Positive stop is required;
Backcheck cannot be used as a stop
• Controls how fast the door closes to
approximately 8" from the closed position,
along with the closer spring
Latching speed valve
ARM
O
TYPE
CO2011
Things to Consider
ARM
TYPE
PF9
CO2101
P9
CO2021
P10
CO2021
H
CO2051
PS/CPS
CO2021
PH9
CO2061
CPSH/PSH
CO2061
F
CO2091
All are certified ANSI types including options
PT4 A, B, D, E, F, G, H
1. Size and Weight of Door
The 351 Door Closers is non-sized so that
closing force can be adjusted in the field
to accommodate various door sizes and
weights.
2. Interior Application
The standard application is the most
efficient in terms of power and control.
3. Exterior Application
The top jamb, corner bracket or parallel arm
application should be used. Exterior doors
require greater closing forces because of
draft conditions. Always place the closers
out of the weather.
4. Degree of Opening
Proper arm and position on the door is most
important to permit the door to open far
enough to allow adequate traffic flow.
5. Function
Closers are available with hold-open, positive
stop or fusible link hold-open arms.
6. Special Condition
Consult factory when special hinges,
overhead holders or other specialized
hardware is used.
1-800-727-5477 • www.sargentlock.com
1
90120:D 07/9/10
How to Select the Proper Closer
ANSI Standards
Copyright © 2005, 2008-2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
• Controls the speed of the door during
the final 8" of door swing
• The force the door closes with is
controlled by the closer spring
• Note: This adjustment is critical for
door latching
Features and Benefits
351 Series Powerglide®
GLAND
“O” RING
SEAL
5/8" SPRING POWER ADJUSTMENT NUT
HEAT TREATED
STEEL SPINDLE
NEEDLE
BEARINGS
CAPTIVATED ADJUSTING VALVES
NON-HANDED COVER
INSERT IS REMOVABLE
AND PLACED IN
UNUSED OPENING
90120:D 07/9/10
Copyright © 2005, 2008-2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
The 351 Series complies with ADA for reduced open forces
of 5 lbs. for interior and 8 lbs. for exterior doors
Features
Heavy Duty Construction
Full Complement of Arm Types
• Certified ANSI/BHMA A156.4 Grade 1
• Conforms to UL10C and UBC for positive
pressure fire test
• UL Listed and cUL Listed to Canadian Safety
Standards listed for use on fire doors
• Ten year warranty
• User friendly versatile mounting applications
permit standard, top jamb, parallel and track
installations
• Self sticking templates supplied for most
applications
• Adjustable spring power allows 351 closers a
size range of 1 through 6. They are adjusted
to size 3 before leaving the factory
• One door closer body for all applications.
All 351 are non-handed
• Meets ADA requirements in all applications,
except Push Side Track application
(except track)
• High impact non-corrosive plastic covers with
two machine screws standard, metal covers
and lead lined are optional
• All weather fluid allows closer to operate
effectively in extreme temperatures without
readjustment
• 1-1/2" diameter piston for superior door
control
• Standard pressure relief valves for both
opening and closing cycles protect the door
& frame from damage caused by abuse
• Heat treated full closed rack and pinion
provide control from the full open position
• Heavy duty one piece die cast aluminum
silicon alloy body with 14% silicon provides
superior strength and wear resistance
• 1/2" arm engagement over a 7/16 square
spindle ensures a wear-resistant tight joint
• Interchangeable forged steel arms
• Standard and parallel arms
• Push and pull track arms
(including double egress)
• Heavy duty forged steel arms are finely
finished and interchangeable between
SARGENT 351, 1431 and 281 Series
Fasteners
Innovation
• Machine Screws and self tapping screws
provided for closer and arm
• In addition, wood screws supplied when
installed on wood doors without through bolts
• SARGENT’s revolutionary MicroShield®
available. This antimicrobial silver-based
finish coating permanently suppresses the
growth of bacteria, algae, fungus, mold
and mildew. EPA and NSF approved and
FDA listed.
2
Valves
• Brass body low sensitivity control valves
offer separate regulating for door speed,
latching, backcheck and optional
delayed action
• All valves are controlled by an 1/8" allen
wrench to discourage tampering and are
captivated to prevent removing valves
from the body and damaging door closer
• Adjustable backcheck (standard) protects
the door and hardware from damage during
the opening cycle
• Adjustable delayed action (optional) permits
easy access for physically impaired individuals
• Valves are captivated to prevent accidental
removal
1-800-727-5477 • www.sargentlock.com
Confirm that we are using parallel arm wherever possible
Standard Applications
351 Series Powerglide®
351-0 Standard Application
O ARM SHOWN
6-5/8"
3/8"(95mm)
(168mm)
(22mm)
7/8"
3-7/8" (58mm)
2-3/16"
(55mm)
90120:D 07/9/10
Copyright © 2005, 2008-2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
The standard application of the 351 door closer is the most common and
the most desirable. The closer mounts on the hinge (pull) side of door
(except when the W Corner Bracket is used). Note: This application is not
recommended on exterior doors (the closer is not protected from weather).
The cover projection normally limits the door opening to a maximum of 160°.
13" (330mm)
VARIES
4-1/2" - 7-1/2"
(114mm - 191mm)
351 Standard Application for:
351 Standard Application Door
Opening Range
• Interior Doors Opening In or Out
(Range based on Mounting Position)
• Exterior Doors Opening In
• O- Standard Arm: 120° - 180°
• Maximum Reveal 7/16"
• H- Hold Open Arm: 90° - 160°
• Non-hand universal body
• F- Fusible Link Hold Open Arm: 75°–135°
Adjustable Closing Force
Arm Leverage Adjustment
• Interior doors to 5'0" wide
Closers using “O” or “F”
arms have the provision
to increase closing power
by 15% by adjusting
foot pivot
• Exterior doors to 4'0" wide
• Shipped factory preset for 3'0" door
• Factory pre-sized upon request
Wall Clearance Requirement
Door in
Closed Position
Door in
Open Position
2-3/16" MIN SPACE
(56mm)
Cover Projection normally limits
door opening to 160°
4
1-800-727-5477 • www.sargentlock.com
Confirm that we are using parallel arm wherever possible
Arms and Accessories
for Standard Applications
351 Series Powerglide®
F - Fusible Link Hold Open Arm
H - Hold Open Arm
• Forged Steel
Main Arm
• Non-handed
• Hand is changed
by inverting the
foot assembly
• Friction type holder easily
adjusted by a wrench
• Permits 180° door opening
• Holds open from 80° to 180°
Order as 25-O x finish for arm only
Includes: 63-2607 - Main arm
63-2216 - Foot assembly
63-3684 - Screw pack
Order as 25-H x finish for arm only
Includes: 63-2229 - Main arm
61-2303 - Foot assembly
63-3684 - Screw pack
O8 - Mortise Foot Arm
Order as 25-F x hand x finish for arm only
Includes: 63-2240 - Left hand main arm
63-2241 - Right hand main arm
63-2468 - Foot assembly
63-3684 - Screw pack
H8 - Mortise Foot Hold Open Arm
• Forged Steel
Main Arm
• Non-handed
• Permits 120°
door opening
• Commonly used
with bull nose frames
Order as 25-O8 x finish for arm only
Includes: 63-2607 - Main arm and link assembly
63-2273 - Foot assembly
63-2391 & 63-3684 - Screw packs
OLC - Standard Arm for Low Ceiling
• Forged Steel
Main Arm
• Non-handed
• 1-1/4" between
the top of door to
ceiling is required
for OLC Arm
• Permits 120° door opening with
standard mounting
Ceiling
Order as 25-OLC x finish for arm only
Includes: 63-2549 - Main arm and
link assembly
2216 - Foot assembly
63-3684 - Screw pack
• Forged Steel
Main Arm
• Handed same
as door
• Friction type
holder easily adjusted by a wrench
• Holds open from 80° to 140°
• 160° F Link Standard
• Specify 125°F Link when required
1-1/4"
7/16"
Maximum
Reveal Depth
• Forged Steel
Main Arm
• Handed same
as door
• Friction type
holder easily
adjusted by a wrench
• Holds open from 80° to 180°
Order 25 R-H8 for right hand and 25 L-H8 for left hand x finish
for arm only
Includes: 63-2289 - Left hand foot assembly
63-2290 - Right hand foot assembly
63-2229 - Main Arm and Link Assembly
63-2391 & 63-3684 - Screw packs
F8 - Mortise Foot Fusible Link
Hold Open Arm
• Forged Steel
Main Arm
• Handed same
as door
• Friction type
holder easily adjusted by a wrench
• Permits 140° door opening
• Holds open to 140°
• 160° F Link Standard
• Specify 125° F Link when required
Order as 25-F x hand x finish for arm only
Includes: 63-2240 - Left hand main arm assembly
63-2241 - Right hand main arm assembly
61-2273 - Foot assembly
63-3684 - Screw packs
UO Package
UH Package
• Universal hold
open arm package
provides brackets
and arms to install
closer in top
jamb, standard
or parallel
applications
• Order closer as
351-UH x finish
• 351-UH not available
with (MC) metal cover
or plated finishes
Screw packs
63-3684
125-PH9
• Universal arm
package provides
brackets and
arms to install
closer in standard
top jamb or
parallel applications
• Order closer as
351-UO x finish
• 351-UO not available
with (MC) metal cover
or plated finishes
Screw packs
63-3684 &
63-2391
125-P9
351-A Mounting Plate
351- LCN Retrofit Plate
Allows the mounting of a 351 Closer onto a
door with a minimum top rail of 2-3/8"
Order as: 351-A x finish
Allows an LCN 4040 closer body to be replaced
with a SARGENT 351 with an O Arm without
drilling new holes in door (NOTE: New holes
required for arm bracket only)
Order as: 351L x finish
9" (229mm)
6" (152 mm)
Copyright © 2005, 2008-2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
• Forged Steel
Main Arm
• Non-handed
• Permits 120° door
opening with
standard mounting
• Permits 180° door opening with alternate
mounting or corner bracket
• Can be used with the 351L retrofit plate when
replacing a LCN 4040 closer
2-3/8" MIN. TOP RAIL
(60mm)
351-A MOUNTING PLATE
1-800-727-5477 • www.sargentlock.com
5
90120:D 07/9/10
O - Standard Arm
Confirm that we are using parallel arm wherever possible
Parallel Arm Applications
351 Series Powerglide®
351-P9 Regular Duty Parallel Arm
1" MIN
(25mm)
P9 Parallel Arm
Varies 5-7/8" to 6-3/8"
(149mm to 162mm)
3-7/8"
(98mm)
P9 ARM SHOWN
13"
(330mm)
Parallel Arm Applications - The 351 closer is mounted on the push side of the
door. As the door opens, the closer swings with the door and gives full
headroom in the door opening. Other advantages: the closer arm does not
project into the room; the frame can be quite narrow and the door can be
swung open much farther than in
Top Jamb Applications.
Varies
4-1/2" - 7-3/8"
(113mm - 187mm)
90120:D 07/9/10
Copyright © 2005, 2008-2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Narrow Reveal
For use in high traffic and abusive
environments
• Forged steel arm and cast iron foot bracket for
strength and durability
• Oiled bronze bearings for superior wear
resistance
• 2 piece rigid arms for ease of installation
• Friction and positive hold open arms available
• Use friction hold open arms for doors subject to
moderate hold open use
• Dead stop and compression stop arms available
• Security non-hold open arms available
Non hold-open arms
• Two mounting positions for 120° and 180°
maximum door openings
Stop arms
• 6 mounting positions with PS or CPS arms to
allow stop from 85°–110°
Narrow Reveal
Available Arms for institutional installations:
• Regular duty parallel arms
• Offset bracket arms for use with Auxiliary
Holders & Stops
• Parallel flush frame arms
• Flush frame arms for use with Auxiliary Holders
& Stops
• Flush frame, friction Hold Open Arms
NON HOLD OPEN ARMS
• Two mounting positions for 120° and
180° maximum door opening
HOLD OPEN ARMS
• Friction hold open arms available for doors
subject to moderate hold open use
• 6 mounting positions to hold open from
85°–110° with PSH or CPSH arms
• UL Listed fusible hold open arms available
8
1-800-727-5477 • www.sargentlock.com
2-3/16"
(56mm)
Confirm that we are using parallel arm wherever possible
Heavy Duty Parallel Arms
351 Series Powerglide®
P10 - Heavy Duty Parallel Arm
•
•
•
•
Forged Steel Constructions
Non-Handed
Easily installed
Permits 120° opening at standard
mounting
• Permits 180° opening at alternate mounting
• Can be used with the 351L retrofit plate
when replacing a LCN 4040 closer
Order as 25-P10 x finish for arm only
25-P10 Includes: 63-0641 - Main arm
63-3727 - P10 foot assembly
63-3684 & 63-2392 - Screw packs
PS - Heavy Duty Parallel Arm with
Positive Stop
•
•
•
•
•
•
Forged Steel Constructions
Handed arm is field-reversible
Provides built in stop from 85° to 110°
Permits 110° opening maximum
Easily installed
Permits 85° to 110° door opening
Order as 25-PS x finish for arm only
Includes: 63-0641 - Main arm
63-3837 - PS foot assembly
63-3684 & 63-2398 - Screw packs
CPS - Heavy Duty Parallel Arm with
Compression Stop
• Forged Steel Constructions
• Provides built in compression stop
from 85° to 105°
• Permits 105° opening maximum
• Easily installed
• Handed arm is field-reversible
• Dead stop within 3°
Order as 25-CPS x finish for arm only
Includes: 63-0641 - Main arm
63-3830 - CPS foot assembly
63-0516 - Bumper holder
63-3493 - Bumper
63-3684 & 63-2398 - Screw packs
SP10 Heavy Duty Security Arm
PH10 - Heavy Duty Friction Hold
Open Parallel Arm
•
•
•
•
•
Forged Steel Constructions
Provides holder and stop features
Handed arm is field-reversible
Easily installed/adjusted
Permits 85° to 110° door opening
Order as 25-PSH x finish for arm only
Includes: 63-0641 - Main arm
63-3833 - PSH foot assembly
63-3684, 63-2392 & 63-2398 - Screw packs
•
•
•
•
•
Forged Steel Constructions
Adjustable hold open from 75° to 180°
Forged steel arm 11-1/4" (286mm) long
Handed same as door
Use friction hold open arms for doors
subject to moderate hold open use
Order as 25-PH10 x finish for arm only
25-PH10 Includes:
63-0641 - Main arm
63-3839 - Left hand PH10 foot assembly
63-3840 - Right hand PH10 foot assembly
63-3684 & 63-2392 - Screw packs
• Forged Steel Constructions
• Handed arm is field-reversible
• Provides built in compression stop and
holder mechanism from 85° to 105°
• Easily installed/adjusted
• Permits 105° opening maximum
• Dead stop within 3°
Order as 25-CPSH x finish for arm only
Includes: 63-0641 - Main arm
63-3836 - CPSH foot assembly
63-0516 - Bumper holder
63-3493 - Bumper
63-3684, 63-2392 & 63-3487 - Screw packs
Positive Stop Hold Open Arms
(PSH & CPSH ARMS)
• Use on doors subject to repetitive hold
open use
• 6 hold open positions from 85° to 110°
determined by mounting position
• Hold open function may be disengaged
• Hold open tension is easily adjustable
The PSH and CPSH arms project 2-3/4" below
the head stop
1-800-727-5477 • www.sargentlock.com
9
Copyright © 2005, 2008-2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
• Same as P10, except factory assembled
at arm joint (elbow) to prevent
disassembly in SSP package along
with metal cover
CPSH - Heavy Duty Hold Open Parallel
Arm with Compression Stop
90120:D 07/9/10
PSH - Heavy Duty Parallel Hold Open
Arm with Positive Stop
Confirm that we are using parallel arm wherever possible
Regular Duty Parallel Arms
351 Series Powerglide®
Regular Duty Hold Open Arms
P4H - Flush Frame, Friction Hold
Open Arm
• Forged Steel
Main Arm
• Holds open from
75° to 180°
• Easily adjusted by
wrench
• Non-handed
• Use on frames where stop or soffit is
too narrow to mount the standard
hold open foot bracket
Order as 25-PH4 x finish for arm only
Includes: 63-2229 - Main arm
61-2303 - Foot assembly
64-0050 - Foot bracket
63-3684 & 63-2391 - Screw packs
PH9 - Friction Hold Open Arm
• Forged Steel
Main Arm
• Holds open
from 75° to 180°
• Easily adjusted by
wrench
• Non-handed
Order as 25-PH9 x finish for arm only
Includes: 63-2229 - Main arm
61-2303 - Foot assembly
64-0039 - Foot bracket (125 PH9)
63-3684 & 63-2391 - Screw packs
Copyright © 2005, 2008-2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
• Forged Steel
Main Arm
• For use with auxiliary
surface overhead
stops and
holders
• Foot bracket
is offset 1" more than P-9, allowing
door closer to be lowered on door face
• Non-handed
Order as 25-P3 x finish for arm only
Includes: 63-2607 -Main arm
63-2270 -Foot assembly
63-3684 & 63-2391 - Screw packs
P4 - Parallel Flush frame Arm
• Forged Steel
Main Arm
• Foot bracket is
attached to
frame or
transom face
• For use where stop
or soffit is too narrow for the
standard P9
• Permits 120° opening with
standard mounting
• Permits 180° opening with
alternate mounting
• Non-handed
Order as 25-P4 x finish for arm only
Includes: 63-2607 -Main arm
63-2295 -Foot assembly
63-3684 & 63-2391 - Screw pack
• Forged Steel
Main Arm
• Fusible link
melts and
releases
hold
mechanism
allowing door to close
• 160°F fusible link standard;
125°F link optional
• Equipped with adjustable friction holder
• Holds door open from 75° to 180°
• Easily adjusted by wrench
• Handed same as door
Order as 25-PF9 x hand x fusible link degree x finish for arm only
Includes: 63-2229 - Main arm
63-2245 - Left hand foot assembly
63-2246 - Right hand foot assembly
63-3684 & 63-2391 - Screw packs
Narrow Reveal
P3 - 1" Offset Bracket for
use with Auxiliary Holder/Stop
PF9 - Fusible Link Hold Open Arm
P3A - 1-3/4" Offset Bracket for use
with Auxiliary Holder/Stop
• Forged Steel
Main Arm
• For use with auxiliary
surface
overhead
stops and
holders and door coordinators
• Foot bracket lowers door closer an
additional 3/4" below P3 bracket
• Non-handed
Order as 25-P3A x finish for arm only
Includes: 63-2607 -Main arm
63-2274 -Foot assembly
63-3684 & 63-2391 - Screw packs
P4A - Flush Frame Arm for
use with Auxiliary Holder/Stop
• Forged Steel
Main Arm
• For use with auxiliary
surface
overhead
stops and
holders
• Foot bracket is attached to frame
or transom face
• Foot bracket lowers door closer an
additional 3/4" below P4 bracket
• Non-handed
Order as 25-P4A x finish for arm only
Includes: 63-2607 - Main arm
63-2272 - Foot assembly
63-3684 & 63-2391 - Screw packs
P9 - Standard Parallel Arm
• Forged Steel
Main Arm
• Non-handed
• Can be used with
the 351L retrofit
plate when replacing a LCN 4040 closer
Order as 25-P9 x finish for arm only
Includes: 63-2607 -Main arm
63-2271 -Foot assembly
63-3684 & 63-2391 - Screw packs
UO Package
• Universal arm
package provides arms
and brackets to install
closer in standard
top jamb or
parallel
Screw pack
application
63-3684
351-UO not available
with (MC) metal cover
or plated finishes
UH Package
• Universal hold
open arm package
provides brackets and
arms to install
closer in top
jamb, standard
or parallel
applications
90120:D 07/9/10
351-UH not available
with (MC) metal cover
or plated finishes
10
1-800-727-5477 • www.sargentlock.com
125-P9
Screw pack
63-3684
125-PH9
Overview
Von Duprin electric strikes are known for their reliability, durability
and security. The 6200 Series is designed to withstand abuse. Its
heavy duty stainless steel construction is fully UL1034 and UL10C
listed and ANSI/BHMA Grade 1 1500lb. hold force rated.
6200 Series electric strikes are designed for use with a variety
of mortise or cylindrical locksets as well as mortise exit devices.
It interfaces with the latch mechanism of the exit device. The
6200 Series movable lip (keeper) allows a door to open even
when the latch bolt is extended. This feature, called remote
release provides added benefits such as increased convenience
and efficiency. The 6200 Series also provides added security
and traffic control.
6200 Series electric strikes can be used for retrofit applications
or new construction. To assure the proper selection of an electric
strike on new applications, lockset compatibility charts are shown
on the next page. When using a lockset not listed or when
retrofitting a strike to an existing application, please contact Von
Duprin Technical Support for application assistance.
The power failure mode of the 6200 Series can be specified at the
time of order. Fail secure is available for fire rated openings. In a
fail secure application the door is normally locked. To unlock the
door power must be applied. Fail safe strikes which are commonly
used for life safety applications are non-fire rated. To unlock a fail
safe strike power is removed. The 6200 Series comes standard with
24 VDC; 12 VDC and AC operation are optional.
Features and Benefits
•• Non handed design provides greater flexibility
•• Strike box is adjustable to compensate for
misalignment of the door or frame
•• Two piece plug connectors are furnished for ease of
installation and for removal during strike servicing.
•• ANSI 156.5 Grade 1 1500lb. hold force rated
•• UL1034 Burglary-Resistant & UL10C Electric Strike
for Fire Door
•• Six finishes available to suite with existing hardware
•• Durable stainless steel construction
•• 24 VDC standard with 12 VDC and AC operation
optional
6200 Series Electric Strikes
Strikes for Mortise or Cylindrical Devices
Models 6210, 6211, 6211AL, 6211WF,
6212, 6212WF, 6213, 6214, 6215, 6216, 6221,
6222, 6223, 6224, 6224AL, 6225 & 6226
System Components
6200 Series
Model Specifications
Model #
Retrofits Model
6210
6211
6211AL
6211WF
6212
n/a
VD 3140, FA 712
FA 722
FA 732
VD 3146
/4 ”
Latchbolt Throw
3
/4 ”
3
/4 ”
3
/4 ”
3
/4 ”
3
4 7/8 ”
4 7/8 ”
4 7/8 ”
4 7/8 ”
6 3/8 ”
1 21/32”
1 21/32”
1 21/32”
4 1/2 ”
1 21/32”














Hollow Metal


Aluminum


Face Plate Length
Backbox Depth
Mortise
Lockset
Cylindrical
Single
# Doors
Pair
Door &
Frame Type


Wood
Options
Certifications


DS or DS-LC (Dual
Monitor Switches)





EB (Entry Buzzer - Fail
Secure Only)





28 VDC AC rectifier kit





16 VDC solenoid





UL1034





UL10C





ANSI/BHMA 156.5 Grade 1
1500lb. Hold force rated





1
2
3
4
5
Application Notes
Application Notes
1
For use with mortise locks without deadbolt on single door, hollow metal frame applications and using ANSI
prep at standard height. Strike pocket inserts are provided to accommodate different manufacturers deadlocking trigger locations.
2
For use on new installations with mortise locks without deadbolt or cylindrical locks on single door, hollow
metal frame applications. Designed to replace Von Duprin 3140 or Folger Adam 712.
3
For use on new installations with mortise locks without deadbolt or cylindrical locks on single door, aluminum
frame applications
4
For use on new installations with mortise locks without deadbolt or cylindrical locks on single door wood
frame applications. Designed to replace Folger Adams 732. Wood frame horizontal solenoid location differs
from Folger Adams. Requires additional frame prep when retrofitting.
5
For use with mortise locks without deadbolt or cylindrical locks on single door, hollow metal or aluminum
frame applications. Fits modified ANSI 115.2 cutout. Designed to replace Von Duprin 3146
Model Specifications
Model #
6222
6223
6224
6224AL
6225
6226
FA 310-23/
4 OB
VD 3091 & 3092
FA 310-2 3/4
FA 310-2RF
FA 310-2 OB
FA 310-2
Retrofits Model
/”
Latchbolt Throw
Face Plate Length
/”
34
/”
/”
34
34
/”
34
/”
34
34
9”
6”
9”
9”
9”
9”
1 5/8 ”
4 1/2 ”
1 5/8 ”
1 5/8 ”
1 5/8 ”
1 5/8 ”






Mortise






Cylindrical
Backbox Depth
Lockset
Single
# Doors













Pair


Hollow Metal


Aluminum
Door &
Frame Type
Wood







DS or DS-LC (Dual
Monitor Switches)






EB (Entry Buzzer - Fail
Secure Only)






28VDC AC rectifier kit






16VDC solenoid






UL1034






UL10C


ANSI/BHMA 156.5 Grade 1
1500lb. Hold force rated
16
17




12
13
14
15
Application Notes
12 Open back electric strike for use with mortise locks without deadbolt or cylindrical locks on 1 3/4” (44mm)
thick double door applications
13 Closed back electric stirke for use with mortise locks without deadbolt or cylindrical locks on 1 3/4” (44mm)
thick double door applications. 4 3/4” (120mm) minimum stile required. For a concealed vertical rod and
mortise device combination specify “A” backbox.
14 Closed back electric strike for use with mortise locks without deadbolt or cylindrical locks on 1 3/4” (44mm)
or 2 1/4” (57mm) thick double door applications.
15 Closed back electric strike for use with mortise locks without deadbolt or cylindrical locks on 1 3/4” (44mm)
or 2 1/4” (57mm) thick aluminum double door applications.
16 Open back electric stirke for use with mortise locks without deadbolt or cylindrical locks on 1 3/4” (44mm)
thick double door applications.
17 Closed back electric strike for use with mortise locks without deadbolt or cylindrical locks on 1 3/4” (44mm)
or 2 1/4” (57mm) thick double door applications.
Options
Certifications
Application Notes
3
707 Door Construction
Door Technical Data
February, 2010
14 GA. (1.9)
CLOSER REINFORCEMENT CHANNEL
(OPTIONAL)
16 GA. (1.4)
TOP END CHANNEL
14 GA. (1.9) STANDARD
HINGE CHANNEL
12 GA. (2.6) SPECIAL ORDER
POLYSTYRENE CORE
URETHANE (OPTIONAL)
14 GA. (1.9)
LOCK CHANNEL
LOCK PREPARATION
AS REQUIRED
20 GA. (0.9) - 14 GA. (1.9)
FACE SKINS
BONDED TO CORE
16 GA. (1.4)
BOTTOM END CHANNEL
NOTE: SEE PAGE 162 FOR HONEYCOMB OPTION
ASSA ABLOY, the global leader in door opening solutions
L
160
Door Vision Lite Kit (Standard)
Door Technical Data
February, 2009
Type 9 & 10 Window Moulding
L
TYPE 9 - POCKET SIZE: 3/8" (9.2)
TYPE 10 - POCKET SIZE: 9/16" (13.7)
13/16" (19.9)
1-1/16" (26)
GLASS
9/16"
(13.7)
INSIDE
OUTSIDE
#8 SCREW
1-1/2"
(38.1)
U.L. CLIP
1-3/4"
(42.9)
VISIBLE GLASS AREA
5-1/8" (126) MINIMUM BETWEEN
VISIBLE GLASS AREAS.
(INCLUDES MOULDING)
VISIBLE GLASS AREA
NOTE: ON FIRE LABEL DOORS USE A 6" (152.4) MINIMUM
STILE BETWEEN VISIBLE GLASS AREAS AND BETWEEN
VISIBLE GLASS AND EDGES OF DOOR.
ASSA ABLOY, the global leader in door opening solutions
Owner's Manual
D3676/D3677/D3678/D8576
What This Owner's Manual Can Do For You
- It explains exactly how The Rite Door® operates.
- It explains periodic maintenance requirements necessary to assure reliable operation.
- It explains simple things to do and check before you call for service, so you may save the cost of an
unnecessary service call.
- It provides a complete listing of service replaceable parts.
- It provides your Adams Rite Limited Warranty and what steps to take for service.
Owners Record
The model number is located on the hinge stile mounting base. Refer to this number and the additional information below when you call upon your local Rite Door® dealer regarding this product.
Model No: D3676/D8576/D3677/D3678
Finish:
Door Size:
Hardware Supplier:
Date Installed:
Exit Device Operation
The Rite Door® Top Rod Concealed Vertical Rod (CVR) devices provides for life safety, security & fire containment
by use of a rotating top latch and post type header strike. When the push bar is depressed, the top rod retracts to
release the door. Upon closing, the top actuator deadlatches around the top strike post securing the door.
Fire Door Labels, Strikes and Frame Screws
Fire Door Labels and other misc. hardware will be located in a removable channel located at the top of the door.
This channel is secured by two Phillips head screws that can be easily removed. Please contact the factory immediately if this hardware can not be located.
Owner's Manual
Entry Trim Operation
The 3080 series outside entry trim is an available option with The RITE Door®. The entry trim will activate the locking
mechanism with any downward or upward motion of the lever handle. The trim utilizes a clutching mechanism that
protects the lever from forced entry or vandalism. The trim will accept any standard mortise cylinder (1" – 1 ½" long)
with an MS cam if re-keying or new cylinders are required. Spacer rings may be needed to accommodate longer
cylinders. The number of spacers will vary depending on the length of cylinder being used. Maintenance of the trim
will be discussed later in this manual.
Recommended Maintenance
Exit Devices are designed for life safety first. Adams Rite devices are cycle tested in excess of one million cycles, both
as prototypes during design and as quality samples during production. Atmospheric and other localized conditions
may vary greatly, but extremely dirty, salty or abrasive situations could require service attention such as cleaning
and lubrication of moving parts from time to time to assure reliability. Service personnel should be reminded that life
safety is the goal.
Some simple maintenance procedures can be taken to keep the exit device and trim in good working condition.
- Maintaining the correct positioning and tightening of screws on top actuator.
- Lubrication of top actuator from time to time with a high grade, lithium based grease. Moving parts inside the
device and rods can also be sprayed annually with white silicone grease to assure reliability.
- Tightening of pushbar and entry trim screws.
- Tightening of end cap screws.
- Tightening of top strike post.
*** Please note that reliable RITE Door® operation is dependant upon the frame being square and plumb to function
correctly. The diagram below will give you an idea of how to tell if your frame is set properly.
Options
We offer a complete line of factory machining to meet your hardware requirements. We also have a wide range of
factory finishes. Available finishes range from our 17 Designer Colors to custom and opaque matching. Our factory finish meets or
exceeds the quality standards for AWI and WDMA TR-3 finishing specifications.
* To further compliment
our product, we have
the following
profiles available:
Veneer
Glass
0.250
1.250
Core
Solid Wood
Panels
Ogee
Raised-Standard
Flat
Standard Sticking Construction
Veneer
Sticking
0.250
Core
1.250
Ogee-Standard
Ovolo
Square
Mission
Glass
Solid Wood
Ovolo
Veneer
Glass
Veneer
0.250
A wide variety of wood
species are available.
Call for specific options.
Core
0.625
Solid Wood
Mission
Glass
1/4" Temp-Standard
3/16" Obscure/Textured
1/4" White Hue Opaque
1/2" Insulated
1/4" Beveled
Other options are
available.
Veneer
Glass
0.250
0.625
Core
Solid Wood
Square
What is this page for?
Door T op O ptions:
Example of door top and model number combinations: A-6000, AA-4010 etc. Not available on all models.
A
1/2A
AA
1/2AA
L
1/2L
R
1/2R
RR
1/2RR
Particleboard Core Doors
Marshfield Signature Series®
Neutral Pressure, Positive Pressure, Environmental, DurableDoor
Standard Models: DPC, DFP, DURPC
Environmental Models: EPC, EPCUF, EDPCUF, EDURPC, EDURPCUF
TM
Product Features
and Specifications
Interior Use Only
Thickness
1-3/4”, 1-3/8”, 2”, 2-1/4”
Maximum Size
ITS-WH and UL- Max 20 minute
Non Rated
NP
Cat. A (PP)
Cat. A (PPAF)
Cat B (PPFM)
Single
4/0 x 10/0
4/0 x 10/0
4/0 x 10/0
4/0 x 9/0
4/0 x 10/0
Pair
8/0 x 10/0
8/0 x 10/0
8/0 x 9/0
8/0 x 9/0
8/0 x 9/0
DE Pair
8/0 x 10/0
8/0 x 8/0
8/0 x 9/0
N/A
8/0 x 9/0
1-3/8” Single
4/0 x 10/0
3/0 x 7/0
N/A
N/A
3/0 x 7/0
Minimum Size
0/8 x 1/10 or 1/10 x 0/8
Faces
• Wood Veneer
• MDO
Crossbands
Engineered Composite
Stiles*
Manufacturer’s standard construction is 1” structural composite lumber with veneer edge band.
1 3/8” stiles (3/4” Hdwd, 5/8” SCL) available upon request
1 3/8" SCL stiles with veneer edge band available upon request
Top and Bottom Rails*
Manufacturer’s standard construction is 7/8” structural composite lumber.
Wider rails available upon request
Face & Core
Assembly Adhesive
Per requirements of WDMA I.S. 1A, C-6
Core
Particleboard core (which complies with ANSI A208.1) See WDMA Performance Level below.
Lite Openings
See Appendix I
Factory Finish
• Enviroclad UV® cured polyurethane. Meets WDMA TR-6 and AWS System 9.
• Prime
• Opaque
Warranty
Full; life of original installation. No exterior warranty
Security Rating
Class 40, highest security rating possible per UBC standard 41-1
& ASTM F-476 section 18
Acoustic Rating
See Appendix M
Environmental Options &
LEED Credit Contribution
• MR 4-Recycled Content- all models
(Not all credits may be available
with some constructions)
• Decorative Laminate
• Styled ® Door Face
• DurableDoor™ PVC Face
SCL STILE
WITH VENEER BAND
FACE
• MR 5-Regional Materials- all models
(Project must be within 500 miles of Marshfield, WI)
• MR 6-Rapidly Renewable Materials- all models with Bamboo veneer
• MR 7-Certified Wood- EPC, EPCUF, EDURPC, EDURPCUF
• IEQ 4.4-Low-Emitting Materials- all UF models
No Added Urea Formaldehyde Resins
WDMA Performance Level
CROSSBAND
(no crossband
required with
decorative
laminate face)
PARTICLEBOARD CORE
Heavy Duty
* Product does not require blocking for surface hardware.
SCL RAIL
Note: Marshfield DoorSystems doors are manufactured per the standards listed on this page. Specifications are subject to change without notice.
*Note: Fire-Rated doors will be constructed per label service listing and may deviate from above.
PCPDS100
04/10
For more information call:
800-869-3667
©2005 Marshfield DoorSystems, Inc.
Fire-Resistant Composite Core Doors– 45-90 Minute
Neutral Pressure , Positive Pressure, Environmental, DurableDoor™
Standard Models: DFP, DFM, DURFP, DURFM
Environmental Models: EDFPUF 45PP, EDFMUF, EDURFMUF, EDURFPUF
Product Features
and Specifications
Interior Use Only
Thickness
1-3/4"
Maximum Size
Marshfield Signature Series®
ITS-WH and UL
NP
Cat A (PP)
Cat B (PPFM)
Single
4/0 x 10/0
4/0 x 10/0
4/0 x 10/0
Pair
8/0 x 8/0
8/0 x 9/0
8/0 x 9/0
8/0 x 8/0 (45 min. only)
8/0 x 8/0
8/0 x 8/0
DE Pair
Minimum Size
0/8 x 1/10 or 1/10 x 0/8
Faces
• Wood Veneer
• Decorative Laminate
• MDO
• Styled Door Face
• DurableDoorTM PVC Face
®
Crossbands
Engineered Composite, if required per label service listing
Stiles
Manufacturer’s standard construction per label service listing with edge band to match face.
Top and Bottom Rails
Manufacturer’s standard construction per label service listing
Face & Core
Assembly Adhesive
Per requirements of WDMA I.S. 1A, C-6
Core
Fire-resistant composite per label service listing
Lite Openings
See Appendix I
RAIL
Factory Finish
• Enviroclad UV® finish
• Prime
• Opaque
FACE
Warranty
Full; life of original installation. No exterior warranty
Security Rating
Mineral Core- Class 30 per UBC standard 41-1 and ASTM F - 476 Section 18
Particleboard Core- Class 40 per UBC standard 41-1 and ASTM F - 476 Section 18
Acoustic Rating
See Appendix M
Environmental Options &
LEED Credit Contribution
• MR 4-Recycled Content- all models
(Not all credits may be available
with some constructions)
STILE
CROSSBAND
(If required)
• MR 5-Regional Materials- EDFPUF & EDURFPUF models
• MR 6-Rapidly Renewable Materials- all models with Bamboo veneer
• MR 7-Certified Wood- Contact Sales
• IEQ 4.4-Low-Emitting Materials- all UF models
No Added Urea Formaldehyde Resins
FIRE RESISTANT COMPOSITE CORE
RAIL
Note: Marshfield DoorSystems doors are manufactured per the standards listed on this page. Specifications are subject to change without notice.
FMPDS100
11/10
For more information call:
800-869-3667
©2005 Marshfield DoorSystems, Inc.
Standard Lite Mouldings
Marshfield Signature Series®
Appendix A
Lite mouldings are installed on one side and the other side is precut for field installation after glazing. Mouldings are
set for 1/4" glass or upon request for different glass thickness. Marshfield DoorSystems will factory glaze upon
request.
Provide lite kit required for
Lite mouldings are installed on one side and the other side is precut for field installation after glazing.
90-min. label where required.
Wood Lite Kits for Non-Rated and 20-Minute Rated Doors
Glazing compound/caulking must be used when installing glass.
"
4
/
1
"
9/32"
1 1/16"
1/2"
3/4"
4
/
1
"
23/32"
4
/
1/4”
1
3/4”
23/32"
Field Glazing Instructions for
Non-Labeled and 20-Minute Rated
Marshfield DoorSystems doors
1"
23/32"
1/8”
1"
1
1/2"
/
3/4"
1 1/16"
4
3/8"
"
3/8"
1/4"
1/2”
1/8”
• Apply a 1/8" to 1/4" bead of DAP
Alex Plus Acrylic Latex Caulk
Plus Silicone in the corner made
by the glass and the door core.
This bead should be applied on
both sides.
3/8"
19/32”
W-4*
W-3
W-2
W-6
W-7
W-10*
W-8
ITS-WH and UL approved with 1/4" wired glass only and W-2, W-3, W-6, or W-7
True divided lites are available on non-rated doors using a 1/2" wide divider bar
and W-2, W-3, W-6 or W-7 profiles.
Downset may vary due to allowable tolerance deviations in components.
1/4" lip on face on W-2, W-3, W-10
* Not available as 20-Minute Rated
• Moulding should be installed with
16 gauge 2" finish nails. Nails
should be placed 3" from the
end of each moulding piece and
at 6” intervals thereafter.
Classic Grilles™ Removable Grill Work With Fire Ratings up to 90-Minutes
Only available with flat profiled mouldings: W-2, W-6, W-8.
1/4”
Classic Grilles are an option to the Signature Series product offering.
Classic Grilles are removable grill work that has fire-ratings up to 90-minutes.
Classic Grilles feature a dual-lock adhesive that acts as a velcro type material
allowing the grilles to be easily removed for cleaning. Available in a variety of
species. Classic Grilles need to be installed in the feild or can be factory
installed when doors are glazed.
Canada Trim-Lite™ Moulding for 20-Minute Rated Doors Requiring Hose Stream
Caulking required.
/
1
"
4
/
1
"
1 1/16"
/
3
W-2
-
1
"
23/32"
4
/
W
6
-
W
Factory finished doors with
applied mouldings, louvers or
factory glazed lites will have nail
holes filled.
•
Doors to be glazed in the field
will not have nail holes filled,
even if the doors are factory
finished.
Note: For more information on lite
kits to be used with other glazing
materials for rated and non-rated
doors, please contact Marshfield
DoorSystems Sales
& Service Center.
1
23/32"
3/4"
3/4"
1 1/16"
4
1/2"
4
3/8"
"
•
W-7
ITS-WH and UL approved with 1/4" wired glass only. Trim-Lite™ is only required on doors shipping to
Canada or any Jurisdiction that requires hose stream testing.
Downset may vary due to allowable tolerance deviations in components.
Wood Fire-Trim System for 20-Minute Rated Doors.
1
/
5
"
6
1
5
"
61/64"
6
1
3
-
W
/
5
5/16"
37/64"
3/4"
3/4"
61/64"
W-2
/
37/64"
6
-
W
29/64"
6
3/8"
"
W-7
Fire-Trim lite mouldings are for use with 20-minute positive pressure doors and structural
composite lumber core neutral pressure doors. Fire-Trim lite mouldings are set for 5/16" FireLite®
Plus glass thickness. Marshfield DoorSystems will factory glaze upon request.
ITS-WH and UL approved with 5/16" FireLite® Plus glass only.
Downset may vary due to allowable tolerance deviations in
Note: Marshfield DoorSystems doors are manufactured per the standards listed on this page. Specifications are subject to change without notice.
For more information call:
800-869-3667
©2005 Marshfield DoorSystems, Inc.