HLS™One
The Complete Multipoint Hardware Package
Edition 2
Features & Benefits
The Hardware
1. Manufactured from Stainless Steel for the highest level of
corrosion resistance
2. Multiple locking points hold the door tight against weather seals
preventing unwanted drafts
3. Stainless Steel strike plates in the most versatile styles for easier
placement and installation
Latch
4. Self-lubricating parts for lasting durability with less maintenance
5. Full-size screw supports prevent the gear from flexing and
bending ensuring a lifetime of performance and smooth operation
Mishandling Device
6. Field reversible latch and mishandling device allow for simple
installation
Stainless Steel
Deadbolt
7. Trimmable extensions ensure a perfect fit for any door size
8. A simple lift of the lever and turn of the thumbturn is all it takes to
fully engage all locking points quickly and securely
Screw
Support
The HLS™One
•
2
There’s no guesswork about what to order because we have
already pre-selected the most popular and highest quality
components for you.
Before & After:
•
All fasteners needed for installing hardware and strikes are
included in the package.
500 Hours Salt Spray
Yellow Zinc Dichromate
•
Installation and adjustment instructions are included in every
package.
•
Add a HOPPE trim set and adjustable hinges and you have a
convenient, single-source solution to add value to your door.
•
Manufactured right here in the United States!
3000 Hours Salt Spray
Stainless Steel
Frequently Asked Questions
Question:
Answer:
What is ‘HLS™One’?
HLS™One is a complete hardware solution in a box. It is a
multipoint locking system that is pre-configured and specially
packaged to add greater value and convenience.
Isn’t multipoint hardware complicated
and high maintenance?
Not at all. When installed and used properly, multipoint hardware
is simple to operate and requires very little maintenance. The
additional locking points will improve door performance and add
value.
Is it difficult to install?
Installation is easy with a properly prepared sash and frame.
Installation instructions are provided in every HLS™One.
Are all of the necessary strikes and
screws included?
Yes, all strike plates and screws for installation are included in the
hardware package.
Is there a minimum purchase quantity?
No, a minimum purchase is not required.
What is the lead time?
The target is two weeks, but lead times may vary.
What is the warranty?
HOPPE’s HLS™ Multipoint Hardware is backed by a limited lifetime
mechanical and finish warranty.
Can I return individual parts or will I
have to return the whole system?
Single parts can be returned for warranty purposes only. Restocking
fees apply for other accepted returns.
Can I select the products that I want
included in my kit?
For your convenience, we’ve already determined the most popular
products and sizes and selected those for our packs. The balance
of our products are available for purchase as individual components
only.
What do I do for a custom door size?
We recommend the universal packs. See page 4 for pack numbers.
What is the finish of the hardware in the
packs?
To ensure the highest level of corrosion protection and durability,
HOPPE only offers the HLS™One with Stainless Steel components.
Can I get strikes to match the finish of
my handle set?
What type of handles are available for
use with this hardware?
Can you provide hinges as well?
Some strikes may be available in additional finishes for purchase
separately. Please contact your HOPPE Sales Representative.
Any of our HLSTM9000 swing door handle sets may be used with this
hardware. Refer to pages 14 - 17 for our most popular styles, or visit
www.us.hoppe.com for the full offering.
Yes, we recommend adjustable hinges for optimum door
performance. See page 18 for information. Our adjustable hinges
are available in finishes to match our handle sets and can also be
seen online at www.us.hoppe.com.
3
3-Point Manual Tongue System
HLS™One for 1.75” (45 mm) Door Thickness &
36” (914mm) Handle Height
Maximum Cutoff
(Top Extension)
Door Size*
6’8”
Backset
Single Door
Pack
French Door
Pack
1.75”
3210661
3210741
2.38”
3123305
3133706
1.75”
3210661
3270866
2.38”
3123305
3270874
1.75”
3210716
3210759
2.38”
3123356
3133714
1.75”
3210767
2.38”
3222477
(45 mm)
(60 mm)
Top Extension Length
7’0”
(45 mm)
(60 mm)
8’0”
(45 mm)
Top Tongue Position
Universal
Maximum Cutoff
(Bottom Extension)
4
Overall Length
* Multipoint Extensions are trimmable and will fit a range of door
sizes. Refer to Page 7 for a chart of actual door sizes.
For 2.25” (57 mm) Door Thickness
All 3-Point Manual Tongue System Single Door (Active Panel)
Packs Include:
Handle Height
Backset
Deadbolt
Throw
N/A
Order the appropriate Pack(s) from the chart above, and ADD (1)
Latch & Deadbolt Strike No. 2014027 for each 2.25” (57 mm) thick
Active Panel.
Bottom Tongue Position
18mm (0.72)
(45 mm)
(60 mm)
92mm (3.62)
186mm (7.32)
41mm (1.61)
(60 mm)
•
Bottom Gear with selected backset, and 36” handle height.
•
Top Tongue Extension for selected panel height.
•
Latch and Deadbolt Strike with curved lip in Stainless Steel.
•
Tongue Strikes in Stainless Steel.
•
Dust Caps for Strike Plates.
•
Stainless Steel Installation Screws.
•
Installation Instructions.
All 3-Point Manual Tongue System French Door (Active and
Inactive Panel) Packs include the above components, plus:
•
Inactive Panel Bottom Gear with selected backset, and 36”
handle height.
•
Inactive Panel Top Shootbolt Extension for selected panel height.
•
Shootbolt Strikes in Stainless Steel.
3-Point Manual Shootbolt System
20mm (0.79)
HLS™One for 1.75” (45 mm) Door Thickness &
36” (914mm) Handle Height
Door Size*
Top Extension Length
Single Door
Pack
French Door
Pack
1.75”
3686950
3686992
2.38”
3687021
3687055
1.75”
3686976
3687004
2.38”
3687039
3687063
1.75”
3686984
3687012
2.38”
3687047
3687071
(45 mm)
(60 mm)
7’0”
(45 mm)
(60 mm)
Cover Plate
Maximum Cutoff
(Top Extension)
6’8”
Backset
8’0”
(45 mm)
Middle Extension Length
* Multipoint Extensions are trimmable and will fit a range of door
sizes. Refer to Page 7 for a chart of actual door sizes.
For 2.25” (57 mm) Door Thickness
Order the appropriate Pack(s) from the chart above, and ADD (1)
Latch & Deadbolt Strike No. 2014027 for each 2.25” (57 mm) thick
Active Panel.
Overall Length
92mm (3.62)
186mm (7.32)
41mm (1.61)
(60 mm)
Handle Height
18mm (0.72)
Backset
Deadbolt
Throw
All 3-Point Manual Shootbolt System Single Door (Active Panel)
Packs Include:
•
Bottom Gear with selected backset, and 36” handle height.
•
Top Shootbolt Extension for selected panel height.
•
Latch and Deadbolt Strike with curved lip in Stainless Steel.
•
Shootbolt Strikes in Stainless Steel.
•
Dust Caps for Strike Plates.
•
Stainless Steel Installation Screws.
•
Installation Instructions.
20mm (0.79)
All 3-Point Manual Shootbolt System French Door (Active and
Inactive Panel) Packs include the above components, plus:
•
Inactive Panel Bottom Gear with selected backset, and 36”
handle height.
•
Inactive Panel Top Shootbolt Extension for selected panel height.
•
Additional Shootbolt Strikes in Stainless Steel.
5
5-Point Manual Tongue/Shootbolt System
French Door
Pack
1.75”
3210679
3210687
2.38”
3123313
3123321
1.75”
3210695
3210708
2.38”
3123330
3123348
1.75”
3210724
3210732
2.38”
3123364
3123372
(45 mm)
(60 mm)
7’0”
(45 mm)
(60 mm)
8’0”
(45 mm)
(60 mm)
Maximum Cutoff
(Top Extension)
Single Door
Pack
Top Extension Length
6’8”
Backset
Cover Plate
Door Size*
20mm (0.79)
HLS™One for 1.75” (45 mm) Door Thickness &
36” (914mm) Handle Height
Top Tongue/Shootbolt Extension for selected panel height.
•
Latch and Deadbolt Strike with curved lip in Stainless Steel.
•
Tongue Strikes in Stainless Steel.
•
Dust Caps for Tongue, Latch & Deadbolt Strikes.
•
Shootbolt Strikes in Stainless Steel.
•
Stainless Steel Installation Screws.
•
Installation Instructions.
92mm (3.62)
•
18mm (0.72)
Backset
Deadbolt
Throw
Inactive Panel Bottom Gear with selected backset, and 36”
handle height.
•
Inactive Panel Top Shootbolt Extension for selected panel height.
•
Additional Shootbolt Strikes in Stainless Steel.
6
20mm (0.79)
All 5-Point Manual Tongue/Shootbolt System French
Door (Active and Inactive Panel) Packs include the above
components, plus:
•
186mm (7.32)
Bottom Gear with selected backset, and 36” handle height
standard.
Bottom Tongue Position
•
Handle Height
All 5-Point Manual Tongue/Shootbolt System Single Door
(Active Panel) Packs Include:
Overall Length
Order the appropriate Pack(s) from the chart above, and ADD (1)
Latch & Deadbolt Strike No. 2014027 for each 2.25” (57 mm) thick
Active Panel.
41mm (1.61)
For 2.25” (57 mm) Door Thickness
Top Tongue Position
Middle Extension Length
* Multipoint Extensions are trimmable and will fit a range of door
sizes. Refer to Page 8 for a chart of actual door sizes.
HLS™One Door Size Ranges
3-Point Manual Tongue System
Single Doors
1.75” (45 mm) Door Thickness
36” (914mm) Handle Height
French Doors
1.75” (45 mm) Door Thickness
36” (914mm) Handle Height
Door Size
Actual Door Size
Range
Backset
Pack No.
1.75”
6’8” & 7’0”
71.06” - 85.63”
(45 mm)
3210661
(1805 mm - 2175 mm)
2.38”
3123305
1.75”
3210716
(60 mm)
8’0”
79.13” - 99.41”
(2010 mm - 2525 mm)
(45 mm)
2.38”
(60 mm)
3123356
Door Size
Actual Door Size
Range
Backset
Pack No.
1.75”
6’8”
78.70” - 82.64”
(45 mm)
3210741
2.38”
3133706
1.75”
3270866
2.38”
3270874
1.75”
3210759
2.38”
3133714
(1999 mm - 2099 mm)
(60 mm)
7’0”
81.65” - 85.59”
(2074 mm - 2174 mm)
(45 mm)
(60 mm)
8’0”
90.31” - 99.37”
(2294 mm - 2524 mm)
(45 mm)
(60 mm)
3-Point Manual Shootbolt System
Single Doors
1.75” (45 mm) Door Thickness
36” (914mm) Handle Height
French Doors
1.75” (45 mm) Door Thickness
36” (914mm) Handle Height
Door Size
Actual Door Size
Range
Backset
Pack No.
1.75”
6’8”
76.61” - 80.55”
(45 mm)
3686950
(1946 mm - 2046 mm)
2.38”
3687021
1.75”
3686976
(60 mm)
7’0”
82.52” - 86.46”
(2096 mm - 2196 mm)
(45 mm)
2.38”
3687039
1.75”
3686984
(60 mm)
8’0”
94.33” - 98.27”
(2396 mm - 2496 mm)
(45 mm)
2.38”
(60 mm)
3687047
Door Size
Actual Door Size
Range
Backset
Pack No.
1.75”
6’8”
78.70” - 80.55”
(45 mm)
3686992
2.38”
3687055
1.75”
3687004
2.38”
3687063
1.75”
3687012
2.38”
3687071
(1999 mm - 2046 mm)
(60 mm)
7’0”
82.52” - 85.59”
(2096 mm - 2174 mm)
(45 mm)
(60 mm)
8’0”
94.33” - 98.27”
(2396 mm - 2496 mm)
(45 mm)
(60 mm)
7
HLS™One Door Size Ranges
5-Point Manual Tongue/Shootbolt System
Single Doors
1.75” (45 mm) Door Thickness
36” (914mm) Handle Height
French Doors
1.75” (45 mm) Door Thickness
36” (914mm) Handle Height
Door Size
Actual Door Size
Range
Backset
Pack No.
1.75”
6’8”
76.61” - 80.55”
(45 mm)
3210679
(1946 mm - 2046 mm)
2.38”
3123313
1.75”
3210695
(60 mm)
7’0”
82.52” - 86.46”
(2096 mm - 2196 mm)
(45 mm)
2.38”
3123330
1.75”
3210724
(60 mm)
8’0”
94.33” - 98.27”
(2396 mm - 2496 mm)
(45 mm)
2.38”
(60 mm)
3123364
Door Size
Actual Door Size
Range
Backset
Pack No.
1.75”
6’8”
78.70” - 80.55”
(45 mm)
3210687
2.38”
3123321
1.75”
3210708
2.38”
3123348
1.75”
3210732
2.38”
3123372
(1999 mm - 2046 mm)
(60 mm)
7’0”
82.52” - 85.59”
(2096 mm - 2174 mm)
(60 mm)
8’0”
94.33” - 98.27”
(2396 mm - 2496 mm)
Jig Systems Available:
2023741
Frame Kit
2023716
Sash Kit for 45 mm
(1.75”) Backset
2753348
Sash Kit for 60 mm
(2.38”) Backset
Contact your Sales Representative about instructional videos and special pricing on Jig Systems.
8
(45 mm)
(45 mm)
(60 mm)
Reference Drawings - Door Prep & Universal Gear
Wood Eurogroove
Universal Gear
+ .008
- .004
+ 0.2
16.2
- 0.1
.638
+ .008
- .004
+ 0.2
12.2
- 0.1
.32 ±.004
8.1 ±0.1
39.409
1001
LOCKING POINT HEIGHT 816MM [32.13]
.366
+ .008
- .004
+ 0.2
9.3
- 0.1
.11
+ .008
- .004
+ 0.2
2.7
- 0.1
.480
.11
2.7
.47
12
[2.51] or 79 [3.11]
Milling Detail - Lock & Backplate 64Holes
5.12
130
4.83
122.7
.64
16.2
3.62
92
4.25
108
.48
12.2
LOCKCASE
DEPTH
.85
21.5
7.37
187.3
HARDWARE HEIGHT 762 MM [30]
2.76
70
LOCKING POINT HEIGHT 620 MM [24.41]
DEADBOLT THROW
BACKSET
3.622
92
7.323
186
1.614
41
.32
R 8.1
2.520
64
45 mm (1.75”) or 60 mm (2.38”) Backsets
45 [1.77] or 60 [2.36]
9
Multipoint Hardware Installation - Active Panel
Active Panel Hardware Installation
Top
Extension
Machine
Screw
Latch
Lockcase
Note: Main gear and extensions should
be hand-tightened only. Excessive force
may cause driverail to bind and inhibit
system operation.
1. When the door is in the open position, the bevel on the latch
should push the latch into the lockcase when you close the door.
If you need to reverse the latch, see the instructions below.
2. Slide main gear into place, aligning holes drilled in door face with
cylinder, handle holes and lockcase to properly accommodate
trim.
3. Install handle set per instructions included with the set.
4. Remove machine screw in top of lockcase.
5. Slide top extension into place and fasten to lockcase with the
supplied machine screws to door edge. The screws should be
screwed in flush with the faceplate, but not overtightened.
6. Test gear with the door in the open position. Engage system by
lifting handle and note if multipoint system operates on the edge
of the door. Extend deadbolt by turning thumbturn. If system is
working properly, the locking points on the edge of the door and
the deadbolt will extend smoothly and completely. If not working properly, please refer to the Troubleshooting Guide on the
website: www.us.hoppe.com.
Reversing the Latch
1. Push small screwdriver or punch into reversing hole and push
latch up until latch clears lockcase.
2. Rotate latch 180 ° with hand and release back into lockcase.
Removing the Shipping Clip & Reversing the
Mishandling Device
1. Remove sticker covering the shipping clip.
2. Remove shipping clip so that mishandling device is visible and
extended.
3. Make sure mishandling device is sloped in the same direction as
the latch.
4. If not, pull out mishandling device with hand and rotate it 180 °.
5. Release mishandling device back into lockcase.
10
Multipoint Hardware Installation - Inactive Panel
Inactive Panel Hardware Installation
You will need the Construction Handle and Thumbturn Insert that are
provided in your HOPPE Handle Set.
The Inactive Panel System is included in
the French Door Packs listed on pages
6 and 7.
We recommend assembly of the inactive gear in the activated
(locked) position. To be consistent in the operation and assembly,
you should assemble the gear operator as follows:
1. Insert the lockcase into the mortise pocket in the edge of the
inactive panel. Insert the Construction Handle into the handle
hub of the gear and lift up on the handle to force the inactive
gear into the engaged position. Insert the Thumbturn Insert and
turn to lock. The Thumbturn will spin freely after it hits the locking
point.
2. Slide the driverail of the top extension outward to extend the
shootbolt. Connect the serrated driverail of the top extension to
the connector of the main gear. Make sure the teeth are fully engaged (seated into the connector). The shootbolts should extend
3/4”. Screw the top extension to the stile.
3. Finish screwing the inactive system into the stile.
4. Turn the thumbturn insert to unlock. Operate the handle set to
retract and extend the shootbolts. The shootbolts should operate
freely.
5. For a security test, lift up on the handle to engage the shootbolts.
Turn the thumbturn insert to lock them into place. Push down on
the handle in an attempt to disengage the shootbolts, if properly
installed, the shootbolts should not react while the thumbturn
insert is locked.
Cutting Shootbolt Extensions
The faceplate of the shootbolt extension should span from the edge
of the extension you are connecting with to the top edge of the door
panel. You can cut the extension shorter if you use a connecting
plate over the connection (included in the HLS™One). Make sure
that you have at least 1-1/4” of serrations left to make a good connection.
When cutting the extension, make sure to have the end of the drive
rail pulled even with the faceplate.
Correct Cut
Incorrect Cut
11
Strikes Plates
Latch & Deadbolt, Tongue and Shootbolt
Strike Plates are already included in the
HLS™One Packs for 1.75” thick doors
(see pages 6 and 7).
Latch & Deadbolt
Replacement Items
117.4mm (4.62)
Latch & Deadbolt Strike
1.75”
Stainless Steel, Item No. 8787747
Tongue Strike
Stainless Steel, Item No. 2025199
224mm (8.82)
2.25
Stainless Steel, Item No. 2014027
25.4mm (1.00)
Tongue
Shootbolt Strike
Stainless Steel, Item No. 2098911
42mm (1.65)
Shootbolt
12
19mm (0.75)
44.3mm (1.74)
or
53.5mm (2.11)
Accessories
High Performance Cover Plate
High Performance Cover Plate
Shootbolt Sash Support Plate
Item No. 2512296
Stainless Steel
Construction Handle
Construction Handle
Temporary Handle used to retract Latch,
as well as activate/retract Multipoints
Item No. 2426890
Construction Key
Activates the Deadbolt Without Trim
Installed, Item No. 2667482
Construction Key
Construction Handle Set
Foam Eurogroove Plug
Construction Handle Set
Complete Interior and Exterior Trim for
security and weather resistance during
the construction phase
Item No. 2604801
Item No. 2605353 (Incl Construction
Key)
Foam Eurogroove Plug
For 3-Point Systems Only
Gray, Item No. 1963538
13
Solid Brass Handle Sets
München Series
M112PL/374N
2.25” (57 mm)
Door Thickness
Finish
Door Thickness
Active
Inactive*
Active
Inactive*
Resista® Brass
(F77-R)
2116331
2133579
2334848
2334910
Antique Brass
(F73)
8763123
8763127
3227307
3227315
Brushed Chrome
(F41-R)
8763167
8766019
2859425
2860442
Polished Chrome
(F49-R)
8763135
8763147
2859370
2860434
Oil Rubbed Brass
(F79)
8773267
8766015
2859417
2860493
Pure White
(F9010)
8763187
8763191
2969544
3027701
Matte Black
(F9714)
8773711
8773715
2859396
2860477
Satin Nickel
(F42-R)
2094813
2106280
2334864
2334928
Antique Nickel
(F44-R)
2106255
2106298
2859388
2860469
Rustic Umber
(F8709)
2214651
2214660
2859409
2860485
* Fixed Immovable Dummy Sets also available for Inactive Panels.
Handle Sets are configured for a Centered Eurogroove.
Order (1) Handle Set per Door. Each Set Includes Interior and
Exterior Handles, Backplates, Cylinder or Thumburn, and Installation
Hardware.
35mm (1.40)
14
130mm (5.12)
222.6mm(8.76)
173mm (6.82)
92mm (3.62)
58mm (2.28)
126mm (4.95)
10mm (0.41)
11mm (0.43)
114mm (4.49)
70mm (2.76)
Order HBL Entry & Interior Door
Hardware to match your HLS™ patio
door trim, and complete the look
throughout the home. Contact your
HOPPE Sales Representative, or visit
www.us.hoppe.com.
1.75” (45 mm)
6mm (0.24)
Solid Brass Handle Sets
1.75” (45 mm)
2.25” (57 mm)
Door Thickness
Finish
Door Thickness
Active
Inactive*
Active
Inactive*
Resista® Brass
(F77-R)
2131021
2131098
2334400
2334792
Antique Brass
(F73)
2131039
2131101
2608917
2608925
Brushed Chrome
(F41-R)
2131055
2039726
2625995
2859484
Polished Chrome
(F49-R)
2131047
2131119
2859513
2859476
Oil Rubbed Brass
(F79)
2131080
2203477
2859564
2859329
Pure White
(F9010)
2131071
2131127
2805099
2805144
Matte Black
(F9714)
2131063
2039742
2859530
2859302
Satin Nickel
(F42-R)
2094805
2095752
2334418
2334901
Antique Nickel
(F44-R)
2095921
2095939
2859521
2859290
Rustic Umber
(F8709)
2207558
2207566
2859548
2859311
* Fixed Immovable Dummy Sets also available for Inactive Panels.
Handle Sets are configured for a Centered Eurogroove.
Order (1) Handle Set per Door. Each Set Includes Interior and
Exterior Handles, Backplates, Cylinder or Thumburn, and Installation
Hardware.
11mm (0.43)
M151/216N
Order HBL Entry & Interior Door
Hardware to match your HLS™ patio
door trim, and complete the look
throughout the home. Contact your
HOPPE Sales Representative, or visit
www.us.hoppe.com.
124mm (4.89)
53mm (2.09)
Ø 11mm (0.42)
109mm (4.27)
21.5mm (0.85)
222mm (8.74)
173mm (6.81)
92mm (3.62)
70mm (2.76)
112.25mm (4.42)
Verona Series
31mm (1.22)
8mm (0.31)
15
Solid Bronze Handle Sets
Missoula Series
B1023/B3741
1.75” (45 mm)
2.25” (57 mm)
Door Thickness
Finish
Door Thickness
Active
Inactive*
Active
Inactive*
Antique Bronze
(F881)
2923132
2923159
2923212
2923239
Dark Bronze
(F883)
2923141
2923167
2923221
2923247
* Fixed Immovable Dummy Sets also available for Inactive Panels.
Order (1) Handle Set per Door. Includes Interior and Exterior Handles,
Backplates, Cylinder or Thumburn, and Installation Hardware.
130mm (5.12)
240mm (9.45)
182mm (7.17)
92mm (3.62)
70mm (2.76)
115mm (4.54)
46mm (1.80)
127mm (5.00)
38mm (1.50)
8mm (0.31)
Coordinates well with:
München Series
HBL Entry & Interior Door Hardware
Toronto Series
Window Handles
NOTE: Window Handles and HBL Entry & Interior Door Handle Sets
are only available in solid brass base material, so styles and finishes
will vary compared to solid bronze handle sets.
16
Solid Bronze Handle Sets
1.75” (45 mm)
2.25” (57 mm)
Door Thickness
Finish
Door Thickness
Active
Inactive*
Active
Inactive*
Antique Bronze
(F881)
2923095
2923116
2923175
2923191
Dark Bronze
(F883)
2923108
2923124
2923183
2923204
New Orleans Series
B1610/B2161
* Fixed Immovable Dummy Sets also available for Inactive Panels.
Order (1) Handle Set per Door. Includes Interior and Exterior
Handles, Backplates, Cylinder or Thumburn, and Installation
Hardware.
70mm (2.76)
59mm (2.31)
130mm (5.12)
182mm (7.17)
92mm (3.62)
240mm (9.45)
109mm (4.29)
38mm (1.50)
122mm (4.81)
8mm (0.31)
Coordinates well with:
New Orleans Series
HBL Entry & Interior Door Hardware
and Window Handles
NOTE: Window Handles and HBL Entry & Interior Door Handle Sets
are only available in solid brass base material, so styles and finishes
will vary compared to solid bronze handle sets.
17
Adjustable Hinge Sets in Matching Finishes
(1) Set Hinge and (2) Guide Hinges are
included in each Hinge Set. Order (1)
Hinge Set for each door panel weighing
up to 165 lbs.
Finish
Set Number
Polished Brass
(F71)
3227411
Antique Brass
(F73)
3227366
Brushed Chrome
(F41-R)
3227374
Polished Chrome
(F49-R)
3227382
Oil Rubbed Brass
(F79)
3227358
Pure White
(F9010)
3227331
Matte Black
(F9714)
3227323
Satin Nickel
(F42-R)
3227391
Antique Nickel
(F44-R)
3227403
Rustic Umber
(F8709)
3227340
HOPPE recommends additional hinges
for heavier doors. Contact your Sales
Representative for assistance.
18
Single Design Theme
In the past it has been difficult for
designers, builders and architects
to find a complete set of matching
hardware for every opening in a
home. HOPPE North America
solved that problem by introducing
the Single Design Theme Concept,
which means that the same styles
and finishes are offered across a
full range of product lines.
Swinging Patio Doors
Sliding Patio Doors
Fold & Slide
Lift & Slide
Entry Doors
Interior Doors
Windows
You spend a lot of time choosing
just the right materials to give a
home that coordinated, high quality,
designer look. Why wouldn’t you
give the same attention to the doors
and windows? Now when you
select an HLS™One Multipoint
Hardware System and compatible
Handle Set, you have the choice to
let your style and attention to detail
show throughout the home with
matching Window, Sliding, Entry
and Interior Door Handles. Even
our Adjustable Hinges are available
in the same finishes as our Handle
Sets. Everything you need for that
added touch of class that sets you
apart from the rest.
HOPPE not only thinks about
the details for you, we also bring
them all together under one roof.
making HOPPE your Single
Source Supplier for Single Design
Themes. Contact your HOPPE
Sales Representative or visit www.
us.hoppe.com for more information
about coordinating products for your
HLS™ hardware.
19
Distributor:
07/12/250