PGRT
Additional tail lamps
General information on connecting additional tail lamps
General information on connecting additional tail lamps
Tail lamps
There are 3 types of tail lamps:
341 740
• Compact 7-chamber lamp assembly
• LED lamp
• 7-chamber lamp assembly
Compact 7-chamber lamp assembly
Additional tail lamps can be connected in the following two ways:
1. Connection via cable harness for twin tail lamps.
340 905
2. Connection via bodywork cable harness in frame.
The cable harness in connection instructions 1 is a complete cable harness which can
be connected to the vehicle’s standard connector. The cable harness and connector
fit all types of lamps and are available from Scania dealers.
LED lamp
The compact 7-chamber lamp assembly is a shorter option, e.g. for trucks with a tail
lift. It is certified in Europe for horizontal mounting.
341 722
Note:
Comply with local legal requirements when fitting tail lamps on underrun protection.
7-chamber lamp
All three lamps have the same hole template for fitting.
Note:
If the LED tail lamp is fitted on a tractor, an adapter plate is required that moves the
lamp out approx. 50 mm sideways.
More information on changing from bulb to LED lamp is found in the document, LED
lamps for tractors, trucks and trailers under Electrical system.
11:60-08/02 Issue 8.1 en-GB
1 (10)
©
Scania CV AB 2015, Sweden
PGRT
Additional tail lamps
General information on connecting additional tail lamps
The parts can be purchased from a Scania dealer.
Connection options
There are two different connection options depending on which control unit for the
regulation of sight and visibility functions the vehicle is equipped with. The latest
one is called CUV2 in the document and the previous one CUV1. The control unit
version can be seen from the vehicle’s individual chassis specification, ICS. The connection alternatives do not have any clear chassis number limit, therefore variant
codes are used instead.
Control unit
CUV2
CUV1
The individual chassis specification (ICS) can be ordered together with the individual main dimension drawing (ICD) under Drawings (requires login).
Variant code
3115B
3115A
11:60-08/02 Issue 8.1 en-GB
2 (10)
©
Scania CV AB 2015, Sweden
PGRT
Additional tail lamps
General information on connecting additional tail lamps
Connecting (CUV2)
When connecting additional tail lamps, the normal vehicle electrical system and fuses must not be overloaded. See the table below for the maximum permitted continuous loads. If more power is required, a relay must be used.
Connection
Position lamp, right-hand side
Position lamp, left-hand side
Reversing light
Brake lamp
Direction indicator, right-hand
side
Direction indicator, left-hand
side
Rear foglight
Standard current consumers
Standard
load, bulb
End-outline marker lamp for truck
Approx. 40 W
End-outline marker lamp and registration plate lamps Approx. 40 W
on truck
Truck and trailer
4 x 21 W
Rigid truck
2 x 21 W
Trailer
Truck, rear
1 x 21 W
Trailer
Truck, rear
1 x 21 W
Trailer
Rear foglight on truck and trailer
4 x 21 W
Standard load,
LED
10.2 W
10.2 W
Maximum loada
Fuse
144 W
144 W
10 A
2 x 3.7 W + trailer
2 x 2.8 W
2 x 21 W + 2 x 70 W + 10 W
4 x 21 W + 10 W
6 x 21 W
4 x 21 W
5 x 21 W
4 x 21 W
5 x 21 W
8 x 21 W
2 x 9.8 W
2 x 9.8 W
2 x 3.7 W + trailer
CUV2b
a. 60% of the rated current of the fuse or electronic overload protection at continuous load
b. Electronic overload protection
More information about electrical connections can be found in the document General information about installation instructions.
11:60-08/02 Issue 8.1 en-GB
3 (10)
©
Scania CV AB 2015, Sweden
PGRT
Additional tail lamps
General information on connecting additional tail lamps
Connecting (CUV1)
When connecting additional tail lamps, the normal vehicle electrical system and fuses must not be overloaded. See the table below for the maximum permitted continuous loads. If more power is required, a relay must be used.
Connection
Position lamp, right-hand side
Position lamp, left-hand side
Reversing light
Brake lamp
RH direction indicators
LH direction indicators
Rear foglights
Standard current consumers
Standard load,
bulb
End-outline marker lamp for truck
Approx. 40 W
End-outline marker lamp and registration plate lamps on Approx. 40 W
truck
Truck and trailer
4 x 21 W
Truck and trailer
4 x 21 W
RH direction indicators on truck
3 x 21 W
LH direction indicators on truck
3 x 21 W
Rear foglights on truck and trailer
2 x 21 W
Standard load, LED
Maximum loada Fuse
10.2 W
10.2 W
144 W
144 W
2 x 3.7 W + trailer
2 x 2.8 W + trailer
2 x 9.8 W
2 x 9.8 W
2 x 3.7 W + trailer
6 x 21 W
6 x 21 W
5 x 21 W
5 x 21 W
4 x 21 W
10 A
CUV1b
a. 60% of the rated current of the fuse or electronic overload protection at continuous load
b. Electronic overload protection
More information about electrical connections can be found in the document General information about installation instructions.
11:60-08/02 Issue 8.1 en-GB
4 (10)
©
Scania CV AB 2015, Sweden
PGRT
Additional tail lamps
Chassis conditions
Chassis conditions
Extra tail lamps can be connected to the cable harness for tail lamps on all Scania
trucks. Two cable harnesses with part number 1 858 746 are required.
If the extra tail lamps should be connected using a cable harness for bodywork, the
following requirements apply:
Vehicle production period
Production site
Chassis serial number
2005-01-21 Södertälje
2 006 429 Zwolle
5 117 958 Angers
9 097 244 -
Preparations from factory
Option
Bodywork cable harness from cab to frame
Vehicle production period
Production site
Chassis serial number
- 2005-01-20
Södertälje
- 2 006 428
Zwolle
- 5 117 957
Angers
- 9 097 243
Preparations from factory
Option
Bodywork cable harness from cab to frame
Bodywork cable harness in frame
Bodywork cable harness in frame
11:60-08/02 Issue 8.1 en-GB
Alternative
7-pin
7+7-pin
7+7+7-pin
2m
8m
12 m
Variant code
2411B
2411E
2411F
3023A
3023D
3023C
Alternative
7-pin
4+7-pin
4+7+7-pin
7+7-pin
2m
7m
12 m
Variant code
2411B
2411C
2411D
2411E
3023A
3023B
3023C
5 (10)
©
Scania CV AB 2015, Sweden
PGRT
Additional tail lamps
Connection instructions
Connection instructions
Alternative 1: Connection via cable harness for twin
tail lamps
Work description
Disconnect the cable from the tail lamp and route it into the frame so that the connector ends up in the beam web and then connect the cable harness for twin tail lamps.
IMPORTANT!
304 320
Do not clamp the cable to the shrinking tubing close to the connector, the greymarked area on the cable in the illustration.
Cable with shrinking tubing
11:60-08/02 Issue 8.1 en-GB
6 (10)
©
Scania CV AB 2015, Sweden
PGRT
Additional tail lamps
Connection instructions
Part information
Two cable harnesses are required, one for the right-hand side of the vehicle and one
for the left-hand side.
The short part of the cable harness is 1,105 mm and the longer part is 1,355 mm.
304 321
The parts are available from Scania dealers.
Cable harness for twin tail lamps. Part number 1 858 746.
11:60-08/02 Issue 8.1 en-GB
7 (10)
©
Scania CV AB 2015, Sweden
PGRT
Additional tail lamps
Connection instructions
Alternative 2: Connection via bodywork cable harness in frame
Work description
The option Bodywork cable harness in frame is to be connected to the DIN connectors and then routed to the tail lamps.
C487
C486
348 620
For vehicles manufactured up to 8 March 2011, the bodywork cable harness connections can be found on the upper part of the left-hand wheel housing.
C488
330 791
Obtain the signals for the additional tail lamps from the connector for standard functions, C489, and from the central electric unit. The signals are bridged to connector
C494 which passes the signals on to the DIN connectors under the cab via the option
bodywork cable harness from cab to frame.
11:60-08/02 Issue 8.1 en-GB
8 (10)
©
Scania CV AB 2015, Sweden
PGRT
Additional tail lamps
Connection instructions
Part information and connection positions
1
1 Fuse
2 Cable
3
4
5
6
7
8
Supplied from the factory
Cable cross-sectional area 1.5
mm² minimum
Cable
Cable cross-section 2.5 mm² minimum
Connected with ring cable terminal to G15
Fitted by bodybuilder
Bodywork cable harness from cab to frame Pre-routed at the factory
Bodywork cable harness in frame
Cable cross-sectional area 1.5
mm² minimum
Supplied from the factory, fitted
by bodybuilder
Additional tail lamps
Fitted by bodybuilder
Bodywork cable harness in frame
Cable cross-section 2.5 mm²
Supplied from the factory, fitted
by bodybuilder
Rear foglight
Output +24 V
+24 V
G15
57
8
C489
15
4
3
2
1
C494
C494
C494
C489
2
C494
C489
21
20
3
19
18
17
16
15
C494
6
4
5
C486
7
Rear foglight is applicable from the following chassis serial numbers onwards:
6
5
Södertälje
Zwolle
Angers
C486
Chassis serial number
2010-05-21 2 054 445 5 240 385 9 148 934 -
4
3
2
1
7
11:60-08/02 Issue 8.1 en-GB
359 222
Vehicle production period
Production site
9 (10)
©
Scania CV AB 2015, Sweden
PGRT
Additional tail lamps
Connection instructions
São Bernardo do Campo
3 663 314 -
The parts are available from Scania dealers.
11:60-08/02 Issue 8.1 en-GB
10 (10)
©
Scania CV AB 2015, Sweden