1718 W. Fullerton Ave
Chicago, IL 60614
Tel: 773-770-1195
Fax: 773-935-5613
www.edgelighting.com
info@edgelighting.com
© 2013 Edge Lighting. All Rights Reserved.
904-PSB-60W-ELV-24VDC-01
PSB-60W-ELV-24VDC
Installation Instructions for 24 Volt DC Power Supply
GENERAL INFORMATION
- RISK OF FIRE: This product must be installed by a
qualified electrician. Turn the power to the electrical box off
during installation. Read the "Important Safety Instructions "
before installation.
- This product is not suitable for wet locations. It is approved
for the use at any height above the finished floor.
- A typical installation is shown. Specific installation must be
in accordance with the local electrical codes.
- TO REDUCE RISK OF FIRE, it is important to wire the
power supply for the system as described in this
installation instruction.
E360941
IMPORTANT SAFETY INSTRUCTIONS
- Do not install this power supply in a wet location.
- To reduce the risk of the system overheating and possibly
causing a fire, make sure all the connections are tight.
- Do not install *LED fixture closer than three inches or as
specified in the *LED fixture installation instructions to
curtains or similarly combustible materials. Keep insulation
at least 3" away from the enclosure.
- Turn the electrical power off before modifying the lighting
system in any way.
- The system is "UL" listed for USA and Canada only when
all the products used are supplied by Edge Lighting.
- For dimming options refer to EDGELIGHTING.COM.
SAVE THESE INSTRUCTIONS!
* See LED fixture installation instructions for proper
placement.
Install the Power supply
A
1
1
COVER
PHILLIPS
SCREW
1: Loosen and remove the four Phillips screws on the top of
the power supply to remove the cover.
2: Secure the power supply case to the desired location with
the four #6 screws provided.
1
1
2
#6 SCREW
POWER
SUPPLY CASE
3: Install a conduit and power wires from the panel to the
power supply.
B
120V HOT
6
120V NEUTRAL
4: DO NOT connect the power wires to the panel at this time.
5: Ground the power supply housing in accordance with local
electrical codes.
6: Connect the 120 volt hot black wire coming from the power
supply switch to the hot power wire with a wire nut.
NOTE: The bottom white wire coming from the switch is for the
switch light. If not using the switch light, cap the wire with a
wire nut.
7: Connect the 120 volt neutral wire to the white (wraped in
black heat shink) wire coming from the transformer and to
the white wire coming from the power supply switch
(optional) with a wire nut.
5
7
3
TRANSFORMER
CONDUIT
1
C
NOTE: In order to use small gauge wires from the power
supply to the LED fixture, it is recommended to install the power
supply as near as possible to the LED fixture. See "Low Voltage
Wire Size Chart" below.
LED SOFT STRIP
8: Use the "Low Voltage Wire Size Chart" below to determine
the proper wire size connecting the power supply wires to
the LED soft strip wires.
24V DC+
9
NOTE: Maximum length of a single soft strip to be connected to
the power supply is 23' for SS3 and 25' for SS2P.
10
24V DC-
NOTE: Use only 24 volt LED soft strip with this power supply.
9: Connect the red (24V DC+) power supply wire to the red
wire of each LED soft strip with a wire nut.
10: Connect the black (24V DC-) power supply wire to the black
wire of each LED soft strip with a wire nut.
CONDUIT
D
PHILLIPS
SCREW
COVER
11
11
9
11: Replace the power supply cover and tighten the four
Phillips screws on top of the cover.
10
11
11
12: Connect the 120 volt power wires at the panel.
SWITCH
13: Turn on the power.
13
Overall Wiring Diagram
LED SOFT STRIP
WHITE
PSB-60W-ELV-24VDC
BLACK
RED
24V DC+
BLACK
24V DC-
120V INPUT
NEUTRAL
HOT (OUTPUT)
HOT (INPUT)
ELV
LOW VOLTAGE WIRE SIZE CHART
TRANSFORMER
VOLTAGE
24 Volt
WIRE SIZE
UP TO 48 FT
#14 GA
WIRE SIZE
FOR 49-65 FT
#12 GA
WIRE SIZE
FOR 66-107 FT
#10 GA
2