Search ...
Home
Corporate
Product Line
Media
Guidance
Shop
Contact Us
Bandit Industries
About Us
Quality/Innovation
News/Stories
Service/Support
Used Equipment
Our Network
Electric Beast Recyclers / Horizontal Grinders
Model 1680 Electric - Beast Recyclers / Horizontal Grinders
The Model 1680 Electric "Son Of A Beast' is an ideal economical alternative to diesel-powered units for small land clearing operations, municipalities, recycling yards,
and tree services looking for an efficient way to reduce and dispose of brush, limbs, pallets, slab wood, bark, sawmill waste, logging slash, palm, construction waste,
Christmas trees, and other tree waste using the advantages of electric power. The Model 1680 Electric is also an excellent unit for turning unwanted chips into a usable
end product. Chips can easily be ground for a variety of applications for bio-energy industries. It features a 16" diameter capacity with its 18" x 52" mill opening and
can be equipped with either a 200 or 250 horsepower WEG electric motor.
The electric version of the Model 1680 is equipped with the patented Bandit cuttermill, which has proven to be the most efficient means of breaking down a wide variety
of materials. With a Bandit cuttermill you have the option of cutting, splitting, grinding and chipping with the opportunity to mix and match cutting devices to allow for
the production of uniform material with varying sizes. The cuttermill turns downward, which not only helps to pull material into the mill but also allows it to be
positioned for a decisive splitting action similar to an axe rather than a more violent, intensive, and less effective hammering action found on other grinding platforms.
The result is less vibration and more structural integrity when compared to machines that carry more weight and horsepower.
The Model 1680 Electric features a 26-tooth setup on its cuttermill, allowing it to process a wide range of materials with ease with its 36" diameter cut radius. Different
combinations and styles of cutterbodies and teeth can be configured to control the amount of bite, assist in forwarding material through the screening system, and dial
in the preferred size and consistency of the end product. A chipper knife set-up can also be equipped on the electric Model 1680, allowing it to produce a dimensional,
screened chip that can be used for fuel and other applications demanding a consistent, high-quality, precisely-sized chip.
The WEG electric motors on the Model 1680 Electric are equipped with a 50 horsepower electric pump drive motor and panel,a soft start panel for the main motor, a
design "A" torque for maximum performance, a water and dust tight enclosed fan, class "F" insulation for all frames, and an F1 mount. They are three phase (60 Hertz)
with 208-230/460 or 460 volt options. Feel free to consult with Bandit if you need different electrical requirements as we have worked with many customers to custom fit
their operations.
A single-speed 10' long x 52" wide rubber belt infeed conveyor serves material to the cuttermill at 20 feet per minute on the electric Model 1680, where it is met by 20"
diameter x 52" wide internally driven floating top feed wheel which can guide brushy material into the cuttermill chamber. The cutting action is performed against a
replaceble anvil that is full-width adjustable. Component weight is distributed and supported on a sturdy frame constructed from 1/4" thick steel with 20" deep formed
high tensile steel plating and cross-section bracing using continuous welds for structural integrity as opposed to bolt-together techniques. Thus, in combination with
two 12,000 pound axles, the Model 1680 Electric can provide the necessary physical reinforcement to hold up for many years of service.
A 15-foot long x 48" wide single-speed stationary discharge conveyor provides a total discharge stacking height of 9 feet. A folding discharge conveyor measuring at
30-foot long, however, it can be ordered as an option for those who want a higher discharge height to load top open trucks and trailers.
Customize your electric Model 1680 to the fullest with many productivity enhancing options. While a tether remote control comes standard, a radio remote is also
available permitting an operator to control the unit from an auxiliary loader feeding the grinder. An upgrade to a steel infeed conveyor is also a popular option as well
as a magnetic head pulley for retrieving nails from the flow of ground material on the discharge. For sizing material, select from a variety of screens ranging from 3/4"
to 6" in diameter. Other add-ons worth considering are a folding infeed pan and an air compressor. A full palette of standard and custom paint colors give you the
freedom to choose the look to fit your brand or company.
The electric Model 1680, as with all Bandit Beast Recyclers, is designed and equipped with operator safety, user-friendly control, and simplified maintenance in mind.
Components that are easily accessible save time on routine maintenance schedules and reduce downtime by being more serviceable out in the field. Feel free to
contact a sales representative and ask about cost saving statistics and production numbers based on your individual situation and needs. These factors, in combination
with above-and-beyond factory support for your success, have proven over time that choosing a Bandit Beast Recycler is the best economical decision you can make
for a long-term investment in a horizontal grinder.
Images
Literature
Videos
Options
Specifications
Articles
Used Equipment
STANDARD EQUIPMENT
Horizontal feed with a 36" diameter cut radius and a 52" wide cutter mill
Repaceable cutter anvil
20" diameter x 52" wide top feed wheel. Driven by (1) 12.2 cubic inch hydraulic motor with gearbox. Also features 1 3/4" feed wheel teeth located around
and on sides of feed wheel.
Reversing Auto Feed System
Tether remote control with 50' of cord (Controls yoke up, infeed conveyor forward/reverse, discharge conveyor start/stop, engine throttle, and engine estop).
Single speed 10' long x 52" wide rubber belt infeed conveyor
Electric over hydraulic shut down switches located on each side of machine
15' long x 4' wide single speed (280 FPM) stationary discharge system. (Has an approximate stacking height of 9')
60 gallon hydraulic tank with magnetic drain plug and aluminum fluid sight gauge
Single front hydraulic stabilizer
12 volt system with rubber mounted LED taillights, 6 prong replaceable coiled power cord & protected heavy-duty wiring with junction box, and LED
clearance lights with reflectors. Also includes (1) 1400 CCA battery
Banded Kevlar drive belts with belt shield
Safety DVD, (2) 6" wide x 9" tall Bandit operator's manuals (one paper copy and one waterproof copy tethered to machine) and (1) engine operator's
manual
Fire extinguisher with mount
PAINT SELECTION
Standard Imron Industrial Urethane Bandit Yellow (For Whole Tree Chippers please specify Chipper Guard paint color)
Standard Imron Industrial Urethane Alert Orange (For Whole Tree Chippers please specify Chipper Guard paint color)
Standard Imron Industrial Urethane Cat. Yellow (For Whole Tree Chippers please specify Chipper Guard paint color)
Standard Imron Industrial Urethane Green (For Whole Tree Chippers please specify Chipper Guard paint color)
Standard Imron Industrial Urethane White (For Whole Tree Chippers please specify Chipper Guard paint color)
Standard Imron Industrial Urethane Black (For Whole Tree Chippers please specify Chipper Guard paint color)
Special Imron Industrial Paint (please specify paint color and number)
Special Imron 5000 Paint (please specify paint color and number)
ENGINE SELECTION
250 horsepower WEG electric motor, with a 50 horsepower electric pump drive motor and panel, soft start panel for main motor, design "A" torque for
maximum performance, three phaze (60 Hertz), 208-230/460, or 460 volt options, enclosed fan (water and dust tight), class "F" insulation for all frames,
1.15 service factor, and F1 mount. (Please consult with Bandit if you need different electrical requirements, as additional charges may be applicable).
AXLE SELECTION
Tandem 12,000 pound Leaf Spring electric brake axles
Tandem 12,000 pound air brake axles WITH spring brake (Unit cannot be moved unless hooked up to air)
TIRES/RIMS SELECTION
(4) 235/75R 17.5" tires mounted on HD gray rims
(4) 235/75R 17.5" tires mounted on aluminum rims
(8) 235/75R 17.5" tires mounted on 8-bolt DUAL rims
HITCH SELECTION
3" pintle hitch with safety chains, slip hooks, and 7 prong replaceable coiled power cord
Fifth wheel pintle hook up for model 1680 with safety chains and slip hooks
BEAST CUTTERBODY SELECTION
Tooth holder cutterbody to be installed on machine (26 required for full set)
Chipper knife holder cutterbody to be installed on machine (26 required for full set)
BEAST TEETH/KNIFE SELECTION
2" wide double splitter tooth to be installed on machine (Model 1680)
Double 1" flat carbide tooth to be installed on machine (Model 1680)
2" wide hard face tooth to be installed on machine (Model 1680)
Double blunt nose Butcher tooth to be installed on machine (Model 1680)
Shingle Carbide tooth to be installed on machine (Model 1680)
34 1/2 degree Chipper knife (1/2" x 2 1/8" x 4") to be installed on machine (to be selected with knife style cutterbodies, p/n 977-900722) ((26 required for
1680, 2680 and 3680 can have 30 or 60. If 30 knives are selected, you must also select 30 blank weight blocks))
Counter knife blank to be installed on machine. To be used in most applications, including Bio-Sawdust. (To be selected in lieu of counter-knife for these
applications).
Counter knife (3/8" x 2" x 3") to be installed on machine (The counter-knife blank replaces this item, but this option should still be used to produce a
larger product).
3/4" x 3" stud for chipper knives to be installed on machine (to be selected with p/n's 900-9915-23 or 900-9915-26. Note also to be used with p/n 983302059 which will require 2 per fan).
3/4-16 flange hex nuts for chipper knives to be installed on machine (to be selected with p/n 977-900741)
SCREENS SELECTION
1/2" thick, 1" modified diamond screen to be installed on machine
1/2" thick, 2" modified diamond screen to be installed on machine
1/2" thick, 3" modified diamond screen to be installed on machine
1/2" thick, 4" modified diamond screen to be installed on machine
1/2" thick, 5" modified diamond screen to be installed on machine
1/2" thick, 6" modified diamond screen to be installed on machine
1/2" thick, 3/4" round screen to be installed on machine
FEED SYSTEM OPTIONS
Radio remote control with tether remote back-up and 50' of cord (Controls yoke up, infeed forward/reverse, discharge start/stop, gate open/close,
engine throttle, and engine e-stop).
COLORING OPTIONS
Bandit self contained hydraulic driven wet coloring system (Includes a variable volume pump with line to hook into spray bar, drop tube for the colorant
container, water intake line and a remote control to adjust the flow of water and colorant from the pump. The system can be mounted on the Beast or
can be skid mounted. The hydraulic drive taps into the hydraulic system of the machine).
INFEED OPTIONS
Single speed 10' long x 52" wide steel infeed conveyor
36" hydraulic folding infeed pan
DISCHARGE OPTIONS
30' long x 4' wide single speed (280 FPM) folding discharge system. (Has an approximate stacking height of 14' and Includes magnetic head pulley)
Magnetic head pulley
MISCELLANEOUS OPTIONS
Fan purge on controller
Special side decal applied on each side of infeed hopper
Saylor Beall air compressor with 5.5 horsepower (pull start) Honda gas engine. Includes 50' hose, and 24 gallon air tank. Also Includes: (1) Ingersol-Rand
Model IR2141 (3/4" drive) air wrench, (1) 1 1/2" impact socket for cutterbody bolts, (1) 1 15/16" impact socket for tooth nuts, (1) 1 1/8" impact socket,
and quick couplers and hose.
25' hose reel for air compressor
Water dust suppression system
Stationary unit kit to be shipped loose with machine (Note: price does not include kit installation, this would need to be quoted separately if installation
is needed by Bandit)
Electric flow control kit for infeed and feedwheel
BEAST HEAD OPTIONS
Chipper drum for Beast with knives & holders to be installed on machine (4 knife) (Note: this option does NOT include the standard mill)
BEAST CUTTERBODY OPTIONS
Tooth holder cutterbody to be shipped loose
Chipper knife holder cutterbody to be shipped loose
BEAST TEETH/KNIFE OPTIONS
2" wide double splitter tooth to be shipped loose
Double 1" flat carbide tooth to be shipped loose
2" wide hard face tooth to be shipped loose
Double blunt nose Butcher tooth to be shipped loose
Double Butcher tooth to be shipped loose
34 1/2 degree chipper knife (1/2" x 2 1/8" x 4") to be shipped loose
Counter knife (3/8" x 2" x 3") to be shipped loose (The counter-knife blank replaces this item, but should still be used to produce a larger product).
3/4" x 3" stub for chipper knives to be shipped loose
3/4-16 flange hex nuts for chipper knives to be shipped loose
SCREEN OPTIONS
1/2" thick, 1" modified diamond screen to be shipped loose
1/2" thick, 2" modified diamond screen to be shipped loose
1/2" thick, 3" modified diamond screen to be shipped loose
1/2" thick, 4" modified diamond screen to be shipped loose
1/2" thick, 5" modified diamond screen to be shipped loose
1/2" thick, 6" modified diamond screen to be shipped loose
1/2" thick, 3/4" round screen to be shipped loose
Next >
DEALER NETWORK SEARCH
Product:
BROWSE
Bandit Product Line
Hand Fed Chippers
DEALER LOGIN
Username
Used Equipment Listings
State:
--- Please Select ---
Trade Show Event Calendar
Password
Testimonials / Customer Stories
Country:
--- Please Select ---
Latest News
Remember Me
LOG IN
Forgot your password?
Forgot your username?
SOCIAL NETWORK
Facebook | banditindustries
Twitter | banditchippers
YouTube | banditchippers
YOU ARE HERE: HOME
PRODUCT LINE
BEAST RECYCLERS / HORIZONTAL GRINDERS
1680 ELECTRIC - BEAST RECYCLERS / HORIZONTAL GRINDERS
ELECTRIC BEAST RECYCLERS
MODEL
TOP