The More You Know: Thread
Pattern Basics
Posted 2 hours ago in Daily News, NFA / Suppressors / Class III by Pete with 4 Comments
Tags: barrel, handedness, metric, Mounts, Muzzle, standard, threading, threads, TPI
Credit: http://sub-silentsuppressors.com/
That sharp, corkscrew section on the end of your barrel is called the ‘threads’. And it is
completely ok to admit that is where your level of knowledge on barrel threading ends (until
recently, I was right there with you). For those of us who run stock barrels and muzzle devices,
you probably have never had the need to get into the weeds when it comes to thread
specifications. But some mounting options remind us that not all barrel threads are created equal
– a fact that is especially true when it comes sound suppressors.
Most gun/upper/barrel manufacturers should print their thread specifications either on the owners
manual or on the product page of their website. And some muzzle devices actually have the
thread infomation stamped or engraved directly on the mount itself. But what if you have an older
rifle or an imported pistol where you are forced to do a bit of research before buying a new piston
or mount?
While your best bet is to take your gun to a qualified gunsmith, most of us like to a lot of the
maintenance and customization ourselves. Luckily, there are some basic techniques you can use
to find out more about your barrels threading without having to see a specialist.
Standard vs Metric:
•
•
Most US made components are threaded to US/English/Standard specifications.
These threads are measured in Threads Per Inch (TPI).
Most foreign components are threaded to Metric specifications. These threads are
measured in pitch, which is the distance between adjacent threads.
Both types of threads can also come in either left or right handed twist, but in the barrel-world,
Metric specs are more likely to be a different “handedness”.
From the Screw Thread Wikipedia page:
The helix of a thread can twist in two possible directions, which is known as handedness.
Most threads are oriented so that the threaded item, when seen from a point of view on the
axis through the center of the helix, moves away from the viewer when it is turned in a
clockwise direction, and moves towards the viewer when it is turned counterclockwise. This
is known as a right-handed (RH) thread, because it follows the right hand grip rule. Threads
oriented in the opposite direction are known as left-handed (LH).
By common convention, right-handedness is the default handedness for screw threads.
Therefore, most threaded parts and fasteners have right-handed threads.
Rotating rockets are cool!
Some shooters prefer mounts that come in left-handed threading. The theory is that with the
rotation of the bullet in the same direction of the threads, the mount might have a tendency to
“walk” or loosen.
Here is basic diagram of thread attributes:
Credit: http://specbolt.com/technical.html
Here are two examples of common barrel threads:
US/Standard/English
1/2″x28
1/2″ – Outside Diameter
28 = Threads per inch
Credit: https://www.boltdepot.com
Metric
M13.5×1 RH
13.5mm – Outside Diameter
1 – Thread Pitch
RH – Right Handed Twist
Credit: https://www.boltdepot.com
Silencer Shop has a good write-up on certain firearms and their thread patterns
here: http://blog.silencershop.com/common-barrel-thread-reference/
I’ve summarized the basics:
.22 LR
•
Standard 1/2×28
9mm
•
•
•
Standard 1/2×28
Standard 1/2×36 – Some 9mm carbines
M13.5×1 LH – H&K, Sig Sauer
.40 S&W
•
•
Standard: 9/16×24
M14.5×1 LH – H&K, Sig Sauer
.45
•
•
•
Standard: .578×28
M16x1 LH – H&K USP Tactical uses the
M16x1 RH – H&K Mark 23 (Socom)
5.56mm (.223)
•
•
•
•
Standard: 1/2×28
M13x1 LH – Steyr Aug
M15x1- H&K
9/16×24 – Ruger Mini
7.62mm (.308)/.338LM
•
•
•
•
•
Standard: 5/8×24
M18x1 – Sako TRG
M18x1.5 – Accuracy International
M14x1LH – Some AK47 patterned rifles.
3/4×24 – Desert Tactical Arms
Why all the different sizes for different calibers? Because the differences in bore diameter will
change the amount of leftover barrel material (sometimes referred to as ‘meat’) for threading.
Smaller bores can have smaller threads.
There are also several YouTube videos on barrel threads. Here’s a couple to review:
And just to complicate everything a little bit more, some suppressor manufacturers call for their
own subset of barrel threading specifications. They should provide schematics that a machinist
can use to cut a barrel correctly. As an example, SilencerCo has two different thread patterns for
1/2×28 – one for rimfire silencers and one for centerfire rifle silencers. Their rimfire suppressors
use an o-ring engagement surface that needs a special cut to take full advantage of the mount.
Also, another important distinction: 1/2″x28 rimfire threading should be cut to a total length of 0.4″
whereas 1/2″x28 centerfire should be cut to a total length if 0.6″ – a fact that is missed by some
barrel manufacturers and machinists. This can cause some suppressors to index/seat on the
blast baffle rather than the barrel shoulder.
Final thoughts: just because your barrel is threaded, doesn’t meant that it is ready to spin on a
silencer. Some barrels, the AK variants for instance, are notorious for being out of spec. While
this is usually ok for a flash hider or muzzle brake, using inadequate threading with a sound
suppressor is asking for trouble.
Barrel Threading Basics – And that’s The More You Know