P O L E S
20' TO 70' ROUND TAPERED STEEL POLE
ANCHOR BASE
6" OR 2'6" OF STRAIGHT
AT THE POLE TOP
TAPERED
STEEL SHAFT
Shaft
The pole shaft is fabricated from U.S. made coil stock. It is a
weldable grade, hot rolled commercial quality carbon steel
with a guaranteed minimum yield strength of 55,000 psi after
fabrication. It is a one-piece or two piece construction with a
full-length, longitudinal high frequency resistance weld. The
pole tapers at a rate of .140 inches per foot
BaSe
The anchor base is fabricated from structural quality hot rolled
carbon steel plate, having a guaranteed minimum yield
strength of 36,000 psi. The base plate telescopes the pole
shaft and is circumferentially welded top and bottom.
A full base plate cover is supplied. For 20', 25' and 30' poles,
the cover is made of automotive structural grade ABS plastic
with UV inhibitor to eliminate color fading. It is rust proof and
tamper resistant. For 35' and higher, the base cover is made
of two-piece formed steel.
handholeS
An extruded handhole to facilitate ease of wiring is standard.
A cover with attachment hardware is provided.
anchor BoltS
Anchor bolts are fabricated from structural quality hot rolled
carbon steel bar, having a minimum yield strength of 50,000
psi. Bolts have an “L” bend on the end. The threads plus 3
inches are galvanized. Anchor bolts come with two nuts and
washers.
finiSh
Standard finish is dark bronze powdercoat. Also available as
standard in powder coat is black. Optional powder coat finishes include grey, silver, and white. A galvanized finish is also
available as an option. All powder-coated poles are shipped
wrapped. Galvanized poles are shipped unwrapped. With custom colors applied in the field, poles are shipped unwrapped.
PERIPHERALLY
WELDED REINFORCED
HANDHOLE
Typical
luminaire
Lighting Products,Inc. 150 Pemco Way-Wilmington, DE 19804 Phone 302.892.9000 Fax 302.892.9005 www.pemcolighting.com pemco@ix.netcom.com EE-7(2016)
P O L E S
20' TO 70' ROUND TAPERED STEEL POLE
O r dErInG
CHArT
ANCHOR BASE
9339
O r dErInG
ExAMPLE
5320-RTS/11 5" x 2" 20'
Model Number
Shaft
Size
Mount
Height
Round Tapered Steel
Pole
Type
11
This example illustrates the standard ordering sequence.
Select each part of the ordering number from the
Ordering Chart above.
Shaft
Gauge
*EPA calculations allow for 1.3 Gust Factor. Variations from standard sizes listed above, available upon inquiry at the factory.Satisfactory performance of lighting standards is
dependent upon the standard being properly attached to a supporting foundation of adequate design. PEMCO does not design or offer recommendations for foundations.
PeMco liGhtinG ProdUctS, inc. offerS the PrecedinG inforMation aS a GUide onlY, and aSSUMeS no liaBilitY for itS USe.
do not USe thiS chart aS a GUide for anchor Bolt inStallation; reQUeSt a BaSe teMPlate Before PoUrinG concrete!
Anchor Base Detail
Bolt Slots
Bolt Circle
POLE
DIA.
(IN)
6.00"
BASE DIMENSIONS
BOLT
BASE
CONDUIT
BASE
BOLT
BOLT
CIRCLE
SQUARE
OPENING
THK.
SIZE
PROJECT.
9.50" ± 0.50" 10.50"
5.50"
0.75" 0.75" x 17.00" x 3.00" 3.50" ± 0.25"
7.00" 10.00"± 0.50" 11.00"
6.50"
1.00" 1.00" x 36.00" x 4.00" 4.25" ± 0.25"
8.00" 11.00"± 0.50" 11.75"
7.50"
1.00" 1.00" x 36.00" x 4.00" 4.25" ± 0.25"
9.00" 12.50"± 0.50" 12.00"
8.50"
1.25" 1.25" x 42.00" x 6.00" 5.00" ± 0.25"
9.00"2 12.50"± 0.50" 13.50"
8.50"
1.25" 1.25" x 42.00" x 6.00" 5.00" ± 0.25"
1
1
Pole Diameter
2
includes base cover.
Pole Diameter indludes nut covers.
EE-8(2016)
ANCHOR BOLTS
(SEE DETAIL)
Base
Square
Conduit
Opening
Semi-Flush
Reinforced
Handhole
Lighting Products,Inc. 150 Pemco Way-Wilmington, DE 19804 Phone 302.892.9000 Fax 302.892.9005 www.pemcolighting.com pemco@ix.netcom.com