SEVO® Systems Provider
Remote Annunciator
Designed with:
CP-4410RA
3M™ Novec™ 1230
Fire Protection Fluid
The CP-4410RA remote annunciator is designed to operate
with the CPRP4410 releasing control panel. The unit mounts
to a 4 gang box. There are 34 LED's to indicate a change in
panel status. There is a buzzer on the annunciator that sounds
for any trouble or supervisory condition. Pressing the LAMP
TEST button illuminates all of the lamps. The release panel
supervises and communicates with the annunciator via
separate connections for the RS-485 communication and
the 24VDC power requirements of the CP-4410RA. Seperate
cables should be used for power and communication. Shielded
cable must be used for the communication line. Up to four
annunciators can be connected to one panel. A Rotary switch
is provided on the panel to indicate how many annunciators
are connected. Another rotary switch is on the annunciator
to set the address. The annunciators must be addressed
consecutively.
Architecture/Engineering Specifications
The Annunciator for the extinguishing agent release panel
shall be a microprocessor based device. The unit shall
require 24vdc operating voltage and a shielded RS-485
connection for communication; both supplied by the release
panel. The annunciator shall have a rotary switch to set the
address number of that annunciator to allow for supervision
by the panel. The annunciator shall have indicators for Alarm,
Trouble, and Supervisory per zone, Output circuits active,
Output circuit troubles, AC power, Power trouble, Supervisory
condition, Supervisory trouble, Abort, System trouble, Alarm
silence, Ground fault, Abort, Pre-discharging/Discharged. In
addition to the visual indicators there shall also be a buzzer
that sounds on any trouble or supervisory condition, a button
to silence the buzzer and test the indicators.
• Up to 4 annunciators can be connected to one PFC4410RC
• Rotary switches on panel and annunciator for supervisory purposes
• Trouble/Supervisory buzzer
• Separate LED's for: Alarm and Trouble per zone, Outputs
activated or in trouble, Supervisory, Abort, Supervisory
trouble, Power trouble, System trouble, Alarm silence,
Ground fault, Discharging/Discharged
• Lamp test silence switch
• Slide in Zone & Output identification labels
SEVSafe Environmental
SYSTEMS
Choice
®
info@SEVOSystems.com
•
•
•
•
•
•
•
•
UL, cUL, & CSFM Listed, FM Approved, MEA
Accepted
Dimensions: 8-1/4" W x 4-1/2" H x 1" D
(Approximate)
Enclosure: Stainless steel plate with clear plastic
shield protecting zone and output identification
labels.
Mounts in 4 gang box.
For surface mounting use back box stk# 3006401
Environmental Specifications: Indoor use only
Temperature range 32°F to 120°F (0°C to 49°C)
93% Humidity
Electrical Requirements:
• 24VDC 10 ma standby 26ma max. (lamp test)
• RS-485 Communication: (Two wire Shielded cable
required).
• Ground drain wire to S terminal on PFC-4410RC
only.
• Max. Distance: 2000 ft. using 22 ga. wire and 4000
ft. using 20 ga. wire.
Phone +1.913.677.1112
Fax +1.913.384.5935
14824 West 107th St.
Lenexa, KS 66215 USA
www.SEVOSystems.com
SEVO® Systems Provider
Remote Annunciator
Designed with:
3M™ Novec™ 1230
Fire Protection Fluid
PFC-4410RC Main Board
24 VDC
RS-485
S
CP-4410RA
ANNUNCIATOR SELECTOR
SWITCH SET FOR THE TOTAL
NUMBER OF DEVICES INSTALLED
ON THE RS-485 TERMINALS
120 OHM RESISTOR - REMOVE THE RESISTOR FROM
THE PFC-4410RC AND INSTALL
ON THE LAST DEVICE ONLY.
CONNECT THE DRAIN WIRE OF THE SHIELDED
CABLE TO THE S TERMINAL ON THE PFC-4410RC
ONLY. DO NOT CONNECT THE DRAIN WIRE TO ANY
ANNUNCIATOR. THE DRAIN WIRE MUST MAKE A
CONTINUOUS PATH TO THE LAST ANNUNCIATOR
WHERE IT IS CUT OFF AND INSULATED.
RA-4410RC #1
NOTE: THE RESISTOR IS INSTALLED
ONLY ON LAST DEVICE.
S
24 VDC
RS-485
ANNUNCIATOR ADDRESS SWITCH (FIRST DEVICE, ADDRESS 1)
DO NOT CONNECT THE SHIELDED CABLE TO
THE REMOTE ANNUNCIATOR
RA-4410RC #2
CUT OFF AND TERMINATE THE DRAIN WIRE AT THE LAST DEVICE.
DO NOT CONNECT THE SHIELDED CABLE TO
THE REMOTE ANNUNCIATOR
S
24 VDC
RS-485
INSTALL THE RESISTOR ON THE LAST RA-4410RC
ANNUNCIATOR ADDRESS SWITCH
DWG# 1175-2
SEV
SYSTEMS
Safe Environmental Choice
®
info@SEVOSystems.com
Phone +1.913.677.1112
Fax +1.913.384.5935
14824 West 107th St.
Lenexa, KS 66215 USA
www.SEVOSystems.com
SEVO® Systems Provider
Releasing Circuit Disable Switch
Designed with:
AS-55
3M™ Novec™ 1230
Fire Protection Fluid
Description
The device consists of a stainless steel faceplate and a
modular switch assembly. It is designed to mount on a
standard single gang electrical enclosure.
Application
The AS-55 complies with the requirements of NFPA 72,
2007, 6.12.5, 6.12.5.1, and 6.12.5.2:
• Specifying a physical switch to disconnect the
release circuit in place of a software controlled
disconnect.
• Creating a supervisory condition on the associated
release panel.
Installation and Operation
1. Connect the red and black leads to the 24 VDC
auxiliary power terminals on the release panel. Be
certain to observe polarity.
RED
BLACK
YELLOW
2. Connect the yellow wires to the supervisory zone
on the panel.
YELLOW
ORANGE
ORANGE
•
•
•
•
The connection for the supervisory circuit has 4
wires: 2 yellow and 2 grey. The 2 yellow wires are
for connection to the supervisory circuit. The 2 grey
wires are for connection to additional supervisory
devices or the EOLR for the supervisory zone.
SEVSafe Environmental
SYSTEMS
Choice
®
info@SEVOSystems.com
•
•
•
•
UL recognized components
Dimensions: 2 3/4" W x 4-1/2" H x 2" D
(Approximate)
Mounts on single gang or handy box
Contact Rating: Key operated switch with 2 N.O.
contacts
2.5A/125VAC, 350 mA/125VDC
Power Requirements: 24 VDC
Environmental Specifications: Indoor use only
Temperature range -22°F to 140°F (-30°C to 60°C)
Phone +1.913.677.1112
Fax +1.913.384.5935
14824 West 107th St.
Lenexa, KS 66215 USA
www.SEVOSystems.com
SEVO® Systems Provider
Abort Switch
Designed with:
CP-4410AS
3M™ Novec™ 1230
Fire Protection Fluid
Description
The Potter Abort Switch is designed to be wired to the abort
terminals of the Potter PFC-4410-RC, PFC-4410A-RC and PFC4410RC (9th Edition) releasing panels. The device consists of
a stainless steel faceplate and a modular switch assembly. It
is designed to mount on a standard double gang electrical
enclosure.
EOLR FROM
RELEASING PANEL
DWG. #1136-1
•
•
•
•
•
SEV
SYSTEMS
Safe Environmental Choice
®
info@SEVOSystems.com
UL Listed, and FM Approved
Dimensions: 4-1/2" W x 4-1/2" H x 2" D
(Approximate)
Contact Rating: One N.O. momentary contact
rated.
5 Amps @ 24 VDC (10 ma minimum)
Environmental Specifications: Indoor use only
Phone +1.913.677.1112
Fax +1.913.384.5935
14824 West 107th St.
Lenexa, KS 66215 USA
www.SEVOSystems.com
SEVO® Systems Provider
Pull Station
Designed with:
AL-MR
3M™ Novec™ 1230
Fire Protection Fluid
Description
The Potter Pull Station Series offers a complete line of diecast pull stations for a variety of applications focusing
mainly on fire alarm systems. The pull stations are available
in single or dual action models. All of the pull stations have a
10-amp snap action switch and a dedicated terminal block for
the ease of wire connections. All of the metal is completely
coated to inhibit corrosion and provide for a uniform and
quality finish.
The standard models have a hex key reset. The models are
available with shallow and deep surface mount back boxes,
as well as a weatherproof version that is rated for NEMA 4.
Operation
The Potter single action series of pull stations operate by
pulling the white operating handle straight down and the handle
will lock into place. The dual action stations require the lifting
of the front cover and then pulling the white operating handle
straight down. The stations are reset by opening the front and
placing the handle in the normal position.
Engineering Specifications
The contractor shall furnish and install the Potter series
of pull stations as indicated. The pull station shall be die
cast construction with a "T" type pull handle that is ADA
compliant. Single action pull stations shall be the MS-NBG12. Dual action pull stations shall be the AL-MR. The contact
shall be a single pole, single throw switch rated at 1 amp 30V
DC/125V AC. The device shall have a terminal block for ease
of wiring. Once activated, the pull station shall be reset by
opening the front cover. Opening of the cover in a normal
state shall initiate an alarm.
Specifications
Switch Rating: 1 Amp @ 30 VDC
1 Amp @ 125 VAC
Pull Station Dimensions: 4-3/4" H x 3-1/4" W x 7/8" D
Single Pull Color: Red with raised white letters, white pull bar
with raised red letters
Double Pull Color: Blue with raised white letters.
SEVSafe Environmental
SYSTEMS
Choice
®
info@SEVOSystems.com
•
•
•
•
•
•
•
•
•
•
•
UL and ULc Listed, FM Approved, CSFM Listed,
MEA Approved, ADA Compliant
Single or Dual Action
Terminal connectors
10 Amp Snap Action Switch
Gold plated SPST contacts
Optional auxiliary contacts
Mounts on standard single gangbox
Surface backboxes available
High-gloss red enamel finish
Glass breakrod
Made in the U.S.A.
Phone +1.913.677.1112
Fax +1.913.384.5935
14824 West 107th St.
Lenexa, KS 66215 USA
www.SEVOSystems.com
SEVO® Systems Provider
Indoor/Outdoor Horn
Designed with:
AL-H-IE
3M™ Novec™ 1230
Fire Protection Fluid
The AL-H-IE Electronic Horn allows a number of applications
on a single device. The horn settings include Temporal, NonTemporal, March Time and a Chime sound. The horn also has
Low, Mid and High volume settings for each pattern and tone.
The tones include 2400 Hz, Electro-Mechanical, Broadband
and Chime.
The voltage input can be either regulated DC or full wave
rectified (FWR) 12 volt or 24 volt operation.
The AL-H-IE utilizes a universal mounting plate that will
mount on a single gang, double gang, octagon and 4” square
electrical boxes. Outdoor installations must use either the
BBK-1 4” square (weatherproof bell backbox) or the BBX-5
(weatherproof backbox). The back plate allows the installer
to mount the plate and terminate the wire connections. The
horn attaches in a hinge fashion from the top and is secured
by a single mounting screw. The horn completely covers
the mounting back plate, therefore it can be mounted before
other trades work is completed and not affect the final look.
Call for additional listings
Note: Installation must comply in accordance with
applicable standards.
DWG# 8910006-1A
•
•
•
•
•
•
•
•
•
•
•
33 sound output settings
Horn or chime sound output
Indoor/outdoor* listed
Pre-wire back plate
Universal back plate mounting (single gang, double
gang, octagon, or 4” square)
Single screw mounting
Low current draw
UL and cUL listed
Patents pending
Outdoor installation requires the BBK-1 #1500001, BBX5R #4270048, or BBX-5W #4270049
SEV
SYSTEMS
Safe Environmental Choice
®
info@SEVOSystems.com
OPTIONAL BBK-1
WEATHERPROOF
BACKBOX
A jumper plug is provided to test for correct
wiring in the supervisory mode only. Do not
pass alarm current through the jumper.
Phone +1.913.677.1112
Fax +1.913.384.5935
14824 West 107th St.
Lenexa, KS 66215 USA
www.SEVOSystems.com
SEVO® Systems Provider
Indoor/Outdoor Horn
Designed with:
AL-H-IE
3M™ Novec™ 1230
Fire Protection Fluid
PFC-4410RC Main Board
24 VDC
RS-485
S
ANNUNCIATOR SELECTOR
SWITCH SET FOR THE TOTAL
NUMBER OF DEVICES INSTALLED
ON THE RS-485 TERMINALS
120 OHM RESISTOR - REMOVE THE RESISTOR FROM
THE PFC-4410RC AND INSTALL
ON THE LAST DEVICE ONLY.
CONNECT THE DRAIN WIRE OF THE SHIELDED
CABLE TO THE S TERMINAL ON THE PFC-4410RC
ONLY. DO NOT CONNECT THE DRAIN WIRE TO ANY
ANNUNCIATOR. THE DRAIN WIRE MUST MAKE A
CONTINUOUS PATH TO THE LAST ANNUNCIATOR
WHERE IT IS CUT OFF AND INSULATED.
RA-4410RC #1
NOTE: THE RESISTOR IS INSTALLED
ONLY ON LAST DEVICE.
S
24 VDC
RS-485
ANNUNCIATOR ADDRESS SWITCH (FIRST DEVICE, ADDRESS 1)
DO NOT CONNECT THE SHIELDED CABLE TO
THE REMOTE ANNUNCIATOR
RA-4410RC #2
CUT OFF AND TERMINATE THE DRAIN WIRE AT THE LAST DEVICE.
DO NOT CONNECT THE SHIELDED CABLE TO
THE REMOTE ANNUNCIATOR
S
24 VDC
RS-485
INSTALL THE RESISTOR ON THE LAST RA-4410RC
ANNUNCIATOR ADDRESS SWITCH
DWG# 1175-2
SEVSafe Environmental
SYSTEMS
Choice
®
info@SEVOSystems.com
Phone +1.913.677.1112
Fax +1.913.384.5935
14824 West 107th St.
Lenexa, KS 66215 USA
www.SEVOSystems.com
SEVO® Systems Provider
Indoor/Outdoor Horn
Designed with:
AL-H-IE
3M™ Novec™ 1230
Fire Protection Fluid
6
7
8
Architecture/Engineering Specifications
The installer shall provide and install the Potter AL-H-IE
indoor/outdoor selectable horn. The horn shall have thirtythree (33) different settings. The horn shall be selectable
for continuous (non-temporal), temporal (ANSI Code 3) and
March Time patterns. The horns shall have a 2400 hertz,
Electro-Mechanical, Broadband or a Chime tone. Each of
the patterns and tones shall be selectable for a Low, Mid
or High volume setting. The horn shall operate at 12 or 24
VDC regulated or full wave rectified. The horn shall have
an operating range between 8 and 33 VDC. The horn shall
utilize a mounting plate that allows the installer to pre-wire
the mounting plate. The mounting plate shall be universal
and mount on a single gang, double gang, octagon or 4
inch square box. If the horn is needed in a wet or outdoor
installation, it shall be mounted on either a BBX-1 4”
square back box or a BBK-5 outdoor matching back box.
The horn shall have a gasket on the back plate that seals
the electrical connection of the terminal connection. The
mounting plate shall be completely covered by the horn and
shall be secured by a single screw. Operating temperature
range will be 32°F to 120°F (0°C to 49°C) for indoor model
and -40°F to 151°F (-40°C to 66°C) for outdoor model. The
horn shall be UL listed to standard 464, Audible Signaling
Devices. In addition, the device shall be cUL listed to CANULC S525.
6 5/64 (154.4)
5
5 (127)
1 27/32 (47)
Dipswitch Settings
Pattern
1 ON - Non-temporal
1 OFF - Temporal
1
2
3
4
Both 2 = OFF
1 and 2 ON = March Time
Tone
3 and 4 ON = 2400Hz
3 ON and 4 OFF = Electromechanical
3 and 4 OFF = Chime
3 OFF and 4 ON = Broadband
Volume
5 and 6 ON = High
5 ON and 6 OFF = Mid
5 and 6 OFF = Low
7 and 8 ON = Horn/strobe on 2 wires
7 and 8 OFF = Horn and strobe on 4 wires
DWG# 8910006-3
DWG# 8910006-2A
Voltage
Regulated 12 DC/
FWR
Regulated 24 DC/FWR
Operating
Voltage Range
8 - 17.5V
16 - 33V
Sync Modules
NA
Available
Operating
Temperature
Range
SEV
SYSTEMS
Safe Environmental Choice
®
info@SEVOSystems.com
12/24V
UL Designation
Indoor: 32°F to 120°F (0°C to 49°C)
Outdoor: -40°F to 151°F (-40°C to 66°C)
Phone +1.913.677.1112
Fax +1.913.384.5935
14824 West 107th St.
Lenexa, KS 66215 USA
www.SEVOSystems.com
SEVO® Systems Provider
Wall Mount Strobe/Horn
Designed with:
3M™ Novec™ 1230
Fire Protection Fluid
AL-HIS
The AL-HIS Strobe/Horn Series provides a wide range of
candela light output options in a single device. The candela
settings include a 12 or 24 volt DC operation for the 15, 35
and 60 (75 on axis) candela settings and 24 volt DC operation
for the 15, 35, 60, 75, 95 and 110 candela settings. The
candela setting is displayed through the front window and is
selectable using a drum wheel.
The horn settings include Temporal, Non-Temporal, March
Time and a Chime sound. The horn also has Low, Mid and
High volume settings for each pattern and tone. The tones
include 2400 Hz, Electro-Mechanical, Broadband and Chime. The voltage input can be either regulated DC or full wave
rectified (FWR) 12 volt or 24 volt operation with an operating
range from 8 to 33 V DC. The strobes can be synchronized
using a control panel with the Potter (Amseco) sync protocol
or a SMD10-3A sync module.
The AL-HIS utilizes a universal mounting plate that will
mount on a single gang, double gang, octagon and 4” square
electrical boxes. The back plate allows the installer to mount
the plate and connect the wire connections. The strobe
attaches in a hinge fashion from the top and is secured by
a single mounting screw. The strobe completely covers the
mounting back plate, therefore it can be mounted before other
trades work is completed and not affect the final look. •
•
•
•
•
•
•
•
•
•
•
•
•
12 VDC with 15, 35 or 60 cd setting
24 VDC with 15, 35, 60, 75, 95 or 110 cd settings
6 distinct candela settings
Candela selection view window
15/75 ADA compliant on 60cd setting
33 sound output settings
Horn or chime sound output
Pre-wire back plate
Universal back plate mounting (single gang, double
gang, octagon, or 4” square)
Single screw mounting
Low current draw
UL and cUL listed
Patents pending
SEVSafe Environmental
SYSTEMS
Choice
®
info@SEVOSystems.com
Note: Installation must comply in accordance
with applicable standards.
A jumper plug is provided to test for correct
wiring in the supervisory mode only. Do not
pass alarm current through the jumper.
Phone +1.913.677.1112
Fax +1.913.384.5935
14824 West 107th St.
Lenexa, KS 66215 USA
www.SEVOSystems.com
SEVO® Systems Provider
Wall Mount Strobe/Horn
Designed with:
AL-HIS
3M™ Novec™ 1230
Fire Protection Fluid
Dimensions: inches (mm)
6 5/64 (154.4)
Light output in percentage when measured from the following
directions per UL 1971.
2 5/16 (59)
5 (127)
High voltage may be present inside the light assembly even
though power is not connected. If access to teh coponent
board is required (removal or replacement), the capacitor must
be discarged by touching a wire to both ends of the flashtube.
DO NOT attempt to touch or move the assembly until the
capacitor has been discharged.
Specifications
Strobe Current
Light
Output
Max. RMS Operating Current (mA RMS)
Reg. 12
VDC
Reg. 12
FWR
Reg. 24
VDC
Reg. 24
FWR
15cd
116
152
62
99
35cd
209
267
102
152
60/75cd
254
258
131
190
75cd
NA
NA
146
208
95cd
NA
NA
177
243
110cd
NA
NA
196
268
Voltage
12/24V
UL Designation
Regulated 12 DC/FWR
Regulated 24 DC/FWR
Operating Voltage Range
8 - 17.5V
16 - 33V
Flash Rate
60 times/min.
Sync Module (SMD10-3A)
Operating Temperature Range
NA
Available
Indoor model: 32°F to 120°F (0°C to 49°C)
Note: To determine total current draw, add desired strobe setting and horn
selection. Refer to the installation instructions for further information.
SEV
SYSTEMS
Safe Environmental Choice
®
info@SEVOSystems.com
ON
Horn Dipswitch
Pattern
1 ON - Non-temporal
1
2
3
4
1 OFF - Temporal
Both 2 = OFF
1 and 2 ON = March Time
Tone
3 and 4 ON = 2400Hz
3 ON and 4 OFF = Electromechanical
3 and 4 OFF = Chime
3 OFF and 4 ON = Broadband
Volume
5 and 6 ON = High
5 ON and 6 OFF = Mid
5 and 6 OFF = Low
7 and 8 ON = Horn/strobe on 2 wires
7 and 8 OFF = Horn and strobe on 4 wires
5
6
7
8
Phone +1.913.677.1112
Fax +1.913.384.5935
14824 West 107th St.
Lenexa, KS 66215 USA
www.SEVOSystems.com
SEVO® Systems Provider
Wall Mount Strobe/Horn
Designed with:
AL-HIS
3M™ Novec™ 1230
Fire Protection Fluid
Non-Temporal Horn Current
Pattern
2400 Hz
Electro-Mechanical
Broadband
Chime
Volume
Max. RMS Current
(mA RMS Current)
dBA Reverberant Ratings per
UL464 (dBA @ 10 ft.)
dBA Anechoic Ratings per
CAN/ULC S525 (dBA @ 10 ft.)
Reg 12 VDC
Reg 24 VDC
Reg 12 VDC
Reg 24 VDC
Reg 12 VDC
Reg 24 VDC
High
119
87
87
87
99
100
Mid
44
28
82
82
94
96
Low
30
18
79
80
92
92
High
118
81
86
87
100
100
97
Mid
43
26
82
84
96
Low
27
16
79
80
93
93
High
146
78
86
86
101
102
Mid
41
26
81
82
96
98
Low
28
16
77
79
94
95
High
27
21
70
70
86
86
Mid
11
8
62
62
79
80
Low
9
7
58
57
75
75
Temporal Horn Current
Pattern
2400 Hz
Electro-Mechanical
Broadband
Chime
Volume
Max. RMS Current
(mA RMS Current)
dBA Reverberant Ratings per
UL464 (dBA @ 10 ft.)
dBA Anechoic Ratings per
CAN/ULC S525 (dBA @ 10 ft.)
Reg 12 VDC
Reg 24 VDC
Reg 12 VDC
Reg 24 VDC
Reg 12 VDC
Reg 24 VDC
High
124
87
82
82
100
100
Mid
46
30
77
79
95
96
Low
30
18
74
75
92
92
High
114
80
83
82
100
101
96
Mid
42
27
78
80
95
Low
28
16
75
76
93
93
High
151
80
82
82
101
102
Mid
45
26
77
78
97
98
Low
30
16
75
76
94
95
High
29
21
68
70
86
86
Mid
10
9
61
61
79
79
Low
9
8
55
55
75
76
March Time Horn Current
Pattern
2400 Hz
Electro-Mechanical
Broadband
SEVSafe Environmental
SYSTEMS
Choice
®
info@SEVOSystems.com
Volume
Max. RMS Current
(mA RMS Current)
dBA Reverberant Ratings per
UL464 (dBA @ 10 ft.)
dBA Anechoic Ratings per
CAN/ULC S525 (dBA @ 10 ft.)
Reg 12 VDC
Reg 24 VDC
Reg 12 VDC
Reg 24 VDC
Reg 12 VDC
Reg 24 VDC
High
121
92
83
84
99
100
Mid
47
31
79
81
95
96
Low
36
19
76
77
92
92
High
114
86
83
83
100
100
96
Mid
42
27
80
81
95
Low
30
19
77
77
92
93
High
153
77
83
84
101
102
Mid
42
28
79
80
97
98
Low
29
16
76
77
94
95
Phone +1.913.677.1112
Fax +1.913.384.5935
14824 West 107th St.
Lenexa, KS 66215 USA
www.SEVOSystems.com
SEVO® Systems Provider
Wall Mount Strobe/Horn
Designed with:
AL-HIS
3M™ Novec™ 1230
Fire Protection Fluid
Wiring Diagram
H
H
DWG# 8910004-1
Architecture/Engineering Specifications
The installer shall provide and install the Potter AL-HIS selectable
strobe/horn. The strobe shall have six (6) candela settings. The
candela settings shall be selectable using a drum roller and shall
display the candela setting on the front of the device. The horn
shall have 33 selectable settings configurable by dip switches. The
sounder shall be capable of ANSI Temporal Code 3, March Time and
produce a chime output. The horn shall have three distinct volume
levels. The strobe/horn shall operate at 12 or 24 VDC regulated or
full wave rectified. The strobe/horn shall have an operating range
between 8 and 33 VDC. the strobes an by synchronized using a
SEV
SYSTEMS
Safe Environmental Choice
®
info@SEVOSystems.com
control panel with the Potter sync protocol or the SMD103A sync module. The strobe shall utilize a mounting plate
that allows the installer to pre-wire the mounting plate. The
mounting plate shall be universal and mount on a single gang,
double gang, octagon or 4 inch square box. The mounting
plate shall be completely covered by the strobe and shall
be secured by a single screw. The strobe shall be UL listed
to standard 1638, General Signaling, and standard 1971,
Signaling Devices for the Hearing Impaired. In addition, the
strobes shall be cUL listed to CAN-ULC S526. The horn shall
be UL listed to standard 464, Audible Signaling Devices.
Phone +1.913.677.1112
Fax +1.913.384.5935
14824 West 107th St.
Lenexa, KS 66215 USA
www.SEVOSystems.com
SEVO® Systems Provider
Ionization Smoke Detector
Designed with:
SD-I-24
3M™ Novec™ 1230
Fire Protection Fluid
The SD-I-24 can be used in all areas where Ionization Smoke
Detectors are required. The responsive, yet highly stable
operation allows the SD-I-24 to fit in a wide range of uses.
The SD-I-24 can be used in areas where early warning of
superheated or flaming combustibles is expected.
SB Series style bases may be used with the SD-I-24. The
only current compatible device is the SD-P-24 Photoelectric
detector.
Operation
The SD-I-24 ionization smoke detector utilizes two bi-colored
LED's for status indication purposes. In a normal standby
condition the LED's flash green approximately once each
second. When the detector senses smoke and goes into
alarm the status LED's will latch on red.
A single radioactive source of Americium-241 ionizes two
chambers within the detector, a reference chamber and the
smoke sensing chamber. The air is ionized by this source
and a small DC current flows between the electrodes of
each chamber. Smoke can freely enter the sensing chamber,
while the inner chamber is virtually sealed to smoke. Smoke
entering the sensing chamber causes a reduction in the DC
current flow, the voltage imbalance between the two chambers
is proportional to the smoke density. When the voltage
difference becomes great enough it causes the detector to go
into alarm. The two chamber design is utilized to compensate
for changes in atmospheric and environmental conditions.
•
•
•
•
•
•
•
•
•
•
•
•
Low profile, 1.8” high (with base)
2 or 4 wire base compatibility, relay bases available
Highly stable operation, RF/Transient protection
Low standby current, 40 µA at 24 VDC
Two built-in power/alarm LED’s for 360° viewing
Non-directional smoke chamber
Vandal resistant security locking feature
Built-in magnetic detector sensitivity test feature.
Meets NFPA 72, Chapter 7, Inspection, Testing and
Maintenance requirements
Compatible with PS-24 photoelectric detectors
Backwards compatible with Potter PS and IS smoke
detectors.
Compatible with Potter releasing controls
SEVSafe Environmental
SYSTEMS
Choice
®
info@SEVOSystems.com
•
•
•
•
•
•
•
•
•
•
•
UL , ULC, CSFM Listed, FM Approved
Radioactive Source: AM-241 0.5 µCi
Rated Voltage: 17.7 - 30.0 VDC
Working Voltage: 15.0 - 33.0 VDC
Maximum Voltage: 42 VDC
Supervisory Current: 40 µA at 24 VDC
Surge Current: 200 µA at 24 VDC
Alarm Current: 150 mA at 24 VDC
Ambient Temperature: 32°F to 120°F (0° C to 49°C)
Sensitivity Test: Magnetically activated dual reed
switch test
Mounting: Refer to Potter SB Series Smoke
Detector Base Series, bulletin no. 8840008
Phone +1.913.677.1112
Fax +1.913.384.5935
14824 West 107th St.
Lenexa, KS 66215 USA
www.SEVOSystems.com
SEVO® Systems Provider
Ionization Smoke Detector
Designed with:
SD-I-24
3M™ Novec™ 1230
Fire Protection Fluid
Architecture/Engineering Specifications
SD-I-24 Sensitivity Test Feature
The contractor shall furnish and install where indicated on
the plans, Potter Model SD-I-24 ionization smoke detectors.
The combination detector head and twist­-lock base shall be
UL listed compatible with a UL listed fire alarm panel.
The base shall permit direct interchange with Potter SDP-24 photoelectric type detector and PS-24H combination
photoelectric/heat detector. The base shall be appropriate
twist-lock base SB Series. In the event of partial or complete
retrofit, the SD-I-24 may be used in conjunction with, or as a
replacement for, Potter detectors (SD-P-24, PS-24H and the
SD-I-24) on most SB base applications.
The smoke detector shall have two flashing status LED's for
visual supervision. When the detector is in standby condition
the LED's will flash green. When the detector is actuated, the
flashing LED's will latch on red. The detector may be reset by
actuating the control panel reset switch.
Test Procedure
1. With detector wired to appropriate initiating circuit
or current limited power source and with normal
applied power, place magnet as shown in Fig. 1.
2. Wait at least six seconds. Detector SHOULD NOT
alarm and LED should not light.
3. Place magnet on detector as shown in Fig. 2
(opposite side).
4. Wait at least six seconds. Detector SHOULD
alarm.
5. If detector does alarm when magnet is positioned
as in Fig. 1 or does not produce an alarm when
magnet is positioned as in Fig. 2, detector is not
within specified sensitivity limits and may require
service.
The sensitivity of the detector shall be capable of being
measured. It shall be possible to perform a functional test of
the detector without the need of generating smoke. The test
method shall simulate effects of products of combustion in
the chamber to ensure testing of the detector electronics.
To facilitate installation, the detector shall be non-polarized.
Voltage and RF transient suppression techniques shall be
employed to minimize false alarm potential. Auxiliary SPDT
relays shall be installed where indicated.
The vandal-resistant, security locking feature shall be used
in those areas indicated on the drawing. The locking feature
shall be field removable when not required.
Specifications subject to change without notice.
INT
T
info@SEVOSystems.com
PA
INT
T
LED’S
T
SEV
SYSTEMS
Safe Environmental Choice
®
OT
ES
T
FIG. 1
Conduct testing only under Normal Standby conditions. Abnormal
or Low Power conditions may affect sensitivity. Always reset
power prior to testing of next unit.
N
DO
PA
DO
OT
ES
N
FIG. 2
DWG# 884306-4
Phone +1.913.677.1112
Fax +1.913.384.5935
14824 West 107th St.
Lenexa, KS 66215 USA
www.SEVOSystems.com
SEVO® Systems Provider
Photoelectric Smoke Detector
Designed with:
SD-P-24
3M™ Novec™ 1230
Fire Protection Fluid
The SD-P-24 can be used in all areas where Photoelectric
Smoke Detectors are required. The wide range smoke
chamber makes the SD-P-24 well suited for fires ranging from
smoldering to flaming fires.
SB Series Style bases may be used with the SD-P-24. Current
interchangeable/compatible devices are the SD-I-24 ionization
detector.
Operation
The SD-P-24 photoelectric smoke detector utilizes two bicolored LED’s for indication of status. In a normal standby
condition the LED’s flash green every 3 seconds. When the
detector senses that its sensitivity has drifted outside the
UL listed sensitivity window the LED’s will flash red every
3 seconds. When the detector senses smoke and goes into
alarm the status LED’s will latch on red.
The detector utilizes an infrared LED light source and silicon
photo diode receiving element in the smoke chamber. In a
normal standby condition, the receiving element receives
no light from the pulsing LED light source. In the event of a
fire, smoke enters the detector smoke chamber and light is
reflected from the smoke particles to the receiving element.
The light received is converted into an electronic signal.
Signals are processed and compared to a reference level, and
when two consecutive signals exceeding the reference level
are received within a specified period of time, the time delay
circuit triggers the SCR switch to activate the alarm signal.
The status LED’s light continuously during the alarm period.
•
•
•
•
•
•
•
•
•
•
•
•
•
UL, ULC, and CSFM Listed, FM Approved
Light Source: GaAIAs Infrared Emitting Diode
Rated Voltage: 17.7 - 33.0 VDC
Working Voltage: 15.0 - 33.0 VDC
Maximum Voltage: 42 VDC
Supervisory Current: 45 µA Max. at 24 VDC
Surge Current: 160 µA Max. at 24 VDC
Alarm Current: 150 mA Max. at 24 VDC
Ambient Temperature: 32°F to 120°F (0°C to 49°C)
Sensitivity Test Feature: Automatic Sensitivity window
verification test.
Mounting: Refer to Potter SB Series Smoke Detector
Base series, bulletin no. 8840008.
Low profile, 1.8” high (with base)
2 or 4 wire base compatibility, relay bases available
SEVSafe Environmental
SYSTEMS
Choice
®
info@SEVOSystems.com
•
•
•
•
•
•
•
•
•
•
•
Highly stable operation, RF/Transient protection
Low standby current, 45 µA at 24 VDC
Two built-in power/sensitivity supervision/alarm
LED’s
Non-directional smoke chamber
Vandal resistant security locking feature
Built-in magnetic go/no go detector test feature
Removable smoke labyrinth for cleaning or
replacement
Automatic Sensitivity window verification function
meets outlined requirements in NFPA 72, Chapter
7, Inspection, Testing and Maintenance.
Compatible with IS-24 ionization detectors
Backwards compatible with Potter PS and IS
detectors.
Compatible with Potter releasing controls
Phone +1.913.677.1112
Fax +1.913.384.5935
14824 West 107th St.
Lenexa, KS 66215 USA
www.SEVOSystems.com
SEVO® Systems Provider
Photoelectric Smoke Detector
Designed with:
3M™ Novec™ 1230
Fire Protection Fluid
SD-P-24
Architecture/Engineering Specifications
The contractor shall furnish and install where indicated on the
plans, Potter Model SD-P-24 photoelectric smoke detectors.
The combination detector head and twist-lock base shall be
UL listed compatible with a UL listed fire alarm panel.
The base shall permit direct interchange with Potter, PS24H, combination photoelectric/heat detector and SD-I-24
ionization type smoke detector. The base shall be appropriate
twist-lock base SB Series. In the event of partial or complete
retrofit, the PS-24 may be used in conjunction with, or as a
replacement for, Potter detectors (SD-P-24, PS-24H and the
SD-I-24) the SB base applications.
The smoke detector shall have two flashing status LED’s for
visual supervision. When the detector is in standby condition
the LED’s will flash green. When the detector is outside the
UL listed sensitivity window the LED’s will flash red. When
the detector is actuated, the flashing LED’s will latch on red.
The detector may be reset by actuating the control panel
reset switch.
The sensitivity of the detector shall be capable of being
measured. It shall be possible to perform a functional test
of the detector without the need of generating smoke. The
sensitivity of the detector shall be monitored automatically
and continuously to verify that it is operating within the listed
sensitivity range.
To facilitate installation, the detector shall be non-polarized.
Voltage and RF transient suppression techniques shall be
employed to minimize false alarm potential. Auxiliary SPDT
relays shall be installed where indicated.
The vandal-resistant, security locking feature shall be used in
those areas as indicated on the drawing. The locking feature
shall be field removable when not required.
Specifications subject to change without notice.
PS-24 Sensitivity Test Feature
The SD-P-24 Photoelectric Smoke Detector has a built-in automatic sensitivity test feature.
1. In normal condition, both LED’s flash green.
2. When the sensitivity drifts outside of its sensitivity limits, both LED’s flash red.
3. In the alarm state both LED’s are red continuously.
4. When the sensitivity drifts outside of its sensitivity limits and both LED’s flash red, the device needs to be cleaned
or returned to the factory for cleaning.
SEV
SYSTEMS
Safe Environmental Choice
®
info@SEVOSystems.com
Phone +1.913.677.1112
Fax +1.913.384.5935
14824 West 107th St.
Lenexa, KS 66215 USA
www.SEVOSystems.com
SEVO® Systems Provider
Releasing Control Panel
Designed with:
CPRP4410
3M™ Novec™ 1230
Fire Protection Fluid
The Potter Model CPRP4410 is a flexible multi-hazard
releasing control panel that is well suited for a number of
applications. The CPRP4410 is listed for use with pre-action
and deluge sprinkler suppression systems and agent based
fire suppression systems.
The panel utilizes a microprocessor-based system that
has 19 Standard Programs, which covers a majority of
installations. The simple to follow Menu Structure programs
the entire system in a matter of minutes. In addition to the
Standard Programs, the panel allows custom programming
to accommodate any installation.
The panel is Ninth Edition UL listed, ULC listed, Factory
Mutual, California State Fire Marshal (CSFM) and New York
Materials Equipment Acceptance (MEA) approved.
The CPRP4410 is housed in a durable steel cabinet with
removable door and key lock. The panel is available in either
a red or white finish and an optional flush mount trim ring
is available. The cabinet contains knockouts on the side,
back and top of the cabinet to ease installation. In addition,
the cabinet will house up to 18 amp-hour batteries that will
provide in excess of 90 hours of standby power.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Multi-Hazard Operation
Four Class B Initiating Circuits
Two Class B Supervisory Circuits **
Four Class B Output Circuits
Programmable Cross Zoning
Supervised Microprocessor
32 Character Alpha-Numeric LCD Display
Custom Banner Message and Zone Description text
Custom Zone Description Text
On Board Menu Driven Programming Controls
Releasing Circuits Protected From False Activation
Continuous or Timed Discharge
40 Event History Buffer
Walktest with Automatic Time-out
Dimensions: 18 ¼" x 14 ½" x 4 ¾"
•
•
Alarm, Trouble Supervisory, and Waterflow relays
Optional Class A Initiating Zone and output
module
• 34 character LED supplemental display
• 19 Standard Programs in Panel Memory
• Password Protection for all Programming
• 24 Hour Clock
• Suitable for agent or waterbased extinguishing
• Programmable pre-discharge timers*
• One Class B Abort circuit* (Defaults to additional
supervisory zone
in water based mode.) • Three Abort modes*
* Available in Chemical mode only
** One zone programmable as abort in chemical mode.
UL and ULC Listed, FM Approved, NYMEA
Accepted, and CSFM Approved
SEVSafe Environmental
SYSTEMS
Choice
®
info@SEVOSystems.com
Phone +1.913.677.1112
Fax +1.913.384.5935
14824 West 107th St.
Lenexa, KS 66215 USA
www.SEVOSystems.com
SEVO® Systems Provider
Releasing Control Panel
Designed with:
3M™ Novec™ 1230
Fire Protection Fluid
Architects/Engineers Specifications The control panel for the extinguishing agent releasing system
shall be a microprocessor based control capable of protecting
multiple hazards in one control panel. It shall be Underwriters
Laboratories Inc. listed under Standard 864 Ninth Edition and
Underwriters Laboratories of Canada for Local Control Units
for Releasing Service. The control shall also be approved by
Factory Mutual Research Corporation and be compiant with the
requirements of NFPA-72 (Local: A, M, SS service types; DAC
and NC signaling type) and NFPA12, NFPA12A, NFPA-13, NFPA15, NFPA-16, NFPA-17, NFPA-17A, NFPA-750, and NFPA-2001.
The control shall be housed in an 18 gauge steel cabinet that
has a hinged, removable door with a key lock. The finish shall be
baked enamel and available in red or off-white with contrasting
trim and logo. An optional matching bezel should be available for
semi-flush mounting. The cabinet shall have adequate space to
house 18 AH standby batteries capable of operating the system
for at least 90 hours.
The control shall include a fully supervised integral power supply/
battery charger capable of providing 200mA to the auxiliary
power circuit. It shall also be capable of providing 2.5 Amps to
all releasing and notification appliance circuits combined. All
initiating, output and auxiliary power circuits shall be power
limited.
The control shall have a 32 character (16 characters, 2 lines)
backlit LCD display and a 34 LED supplemental display. All
diagnostic and alarm event information shall be viewable in
text form on this display. A field programmable custom banner
message with the current date and time shall be displayed when
no current alarm or diagnostic information exists.
All operational features of the control panel shall be field
programmable using menu driven selections on the alphanumeric display and on board controls. No special programmer
will be required and jumpers or switches to configure operational
features shall not be permitted. Alarm and trouble indications
shall resound when required.
The control panel shall be equipped with 19 programs built into the
panel memory, 13 for water based extinguishing and 6 for agent
extinguishing. In addition, the panel shall have the ability to add
custom programs. All programming functions shall be password
protected.
The control shall have four fully supervised Class B (Style B)
initiating circuits capable of supporting the operation of 25
compatible 2-wire smoke detectors on each circuit.
The individual circuits shall be selectable through the
programming sequence to operate in one of the following modes:
Conventional, Waterflow, Linear Heat Detection (up to 10,000 feet
per zone), Manual Release, Low Air Alarm, Supervisory, Tamper,
Low Air or High Air.
SEV
SYSTEMS
Safe Environmental Choice
®
info@SEVOSystems.com
CPRP4410
Optional Class A modules, CA2Z, may be added for Class
A operation. The panel shall have a Low Air Zone that
creates a supervisory condition and map to an output.
UL and ULC Listed, FM Approved, NYMEA Accepted,
CSFM Approved
The control shall have two fully supervised Class B (Style
B) supervisory circuits. These circuits shall be selectable
through the programming sequence to operate in one of
the following modes: Supervisory, Tamper, Low Air or
High Air.
The control shall have one fully supervised class B
(style B) Abort circuit with 3 different operating modes,
ULI, IRI, and NYC.
The control shall have four fully supervised Class B (Style
Y) output circuits. These circuits shall be selectable
through the programming sequence to operate as one of
the following: Alarm Notification Appliance, Supervisory
Notification Appliance, Trouble Notification
Appliance or Releasing. The optional CAM module may
be added to convert the outputs to Class A.
The panel shall have an RS-485 output and auxiliary
power outputs for connection and supervision of up to 4
remote annunciators.
The releasing circuits shall be supervised for short
circuit conditions and shall be programmable for cross
zoning operation when required. The discharge timer
for these releasing circuits shall be programmable
for times of 7, 8, 9, 10, 20 minutes or continuous. All
initiating and output circuits shall be capable of being
individually disabled or enabled. In addition, when in the
agent extinguishing mode there shall be a pre-discharge
timer adjustable from 0-60 seconds from an alarm zone
or 0-30 seconds from a manual release zone.
The control shall have a test mode that will automatically
disable all releasing circuits. The test mode shall
operate in such a manner as to automatically reset the
initiating circuit and indicating circuits after detecting
each alarm condition initiated by the test. All testing
shall be recorded in the 40 event history buffer. The test
mode will automatically terminate after twenty minutes
of inactivity.
The control shall have four integral relay contacts rated
3 Amps at 30 VDC for connection to external auxiliary
equipment. One relay shall operate when an alarm
condition occurs, another when a trouble signal occurs,
the third when a supervisory condition occurs, and the
fourth during a waterflow condition.
UL and ULC Listed, FM Approved, NYMEA Accepted, CSFM
Approved.
Phone +1.913.677.1112
Fax +1.913.384.5935
14824 West 107th St.
Lenexa, KS 66215 USA
www.SEVOSystems.com
SEVO® Systems Provider
Bells
Designed with:
3M™ Novec™ 1230
Fire Protection Fluid
AL-B6 AL-B8 AL-B10
These vibrating type bells are designed for use as fire, burglar or
general signaling devices. They have low power consumption
and high decibel ratings. The unit mounts on a standard 4”
(101mm) square electrical box for indoor use or on a model BBK-1
weatherproof backbox or AL-BBD deep weatherproof backbox for
outdoor applications. Weatherproof backbox model AL-BB, Stock
No. 1500001.
UL, ULC, and FM Approved
Sizes Available:
6” (150mm), 8” (200mm) and 10” (250mm)
Voltages Available:
24VAC
120VAC
12VDC (10.2 to 15.6) Polarized
24VDC (20.4 to 31.2) Polarized
Service Use: Fire Alarm
General Signaling
Burglar Alarm
Environment: Indoor or outdoor use (See Note 1)
-40° to 150°F (-40° to 66°C)
(Outdoor use requires weatherproof backbox.)
Termination: AC Bells - 4 No. 18 AWG stranded wires
DC Bells - Terminal strip
Finish: Red powder coating
Optional: Model AL-BB weatherproof backbox
Model AL-BBD deep weatherproof backbox
Size
inches
(mm)
Voltage
Model
Number
Stock
Number
6 (150)
12VDC
MBA126
1750070
.12A
85
76
8 (200)
12VDC
MBA128
1750080
.12A
90
77
10
(250)
12VDC
1750060
.12A
92
78
6 (150)
24VDC
MBA246
1750100
.06A
87
77
8 (200)
24VDC
MBA248
1750110
.06A
91
79
10
(250)
24VDC
1750090
.06A
94
80
6 (150)
24VAC
PBA246
1806024*
.17A
91
78
8 (200)
24VAC
PBA248
1808024*
.17A
94
77
10
(250)
24VAC
PBA2410
1810024*
.17A
94
78
PBA1206
1806120*
.05A
92
83
6 (150)
Current Typical dB
(Max.)
at 10 ft.
(3m) (2)
All DC bells are polarized and have built-in transient protection.
* Does not have ULC listing.
SEVSafe Environmental
SYSTEMS
Choice
®
info@SEVOSystems.com
*
Minimum
dB at 10
ft.
(3m) (1)
Notes:
1. Minimum dB ratings are calculated from integrated
sound pressure measurements made at Underwriters
Laboratories as specified in UL Standard 464. UL
temperature range is -30° to 150°F (-34° to 66°C).
2. Typical dB ratings are calculated from measurements
made with a conventional sound level meter and are
indicative of output levels in an actual installation.
3. ULC only applies to MBA DC bells.
In outdoor or wet installations, bell must be mounted
with weatherproof backbox, AL-BB or AL-BBD. Standard
electrical boxes will not provide a weatherproof
enclosure. If the bell and/or assembly is exposed to
moisture, it may fail or create an electrical hazard.
Phone +1.913.677.1112
Fax +1.913.384.5935
14824 West 107th St.
Lenexa, KS 66215 USA
www.SEVOSystems.com
SEVO® Systems Provider
Bells
Designed with:
AL-B6 AL-B8 AL-B10
3M™ Novec™ 1230
Fire Protection Fluid
Wiring (rear view)
Fig. 3
Bells Dimensions Inches (mm)
Fig. 1
A.C. BELLS
WHITE (IN)
10”
(250)
8”
(200)
WHITE (OUT)
FROM CONTROL
PANEL OR
PRECEDING BELL
6”
(150)
BLACK (OUT)
BLACK (IN)
CAUTION:
WHEN ELECTRICAL SUPERVISION IS REQUIRED USE IN AND OUT LEADS AS SHOWN.
2 11/16”
(68)
NOTES:
DWG# 776-1
1. WHEN USING AC BELLS, TERMINATE EACH EXTRA WIRE SEPARATELY AFTER LAST BELL.
2. END-OF-LINE RESISTOR IS NOT REQUIRED ON AC BELLS.
DWG# 776-3
Weatherproof Backbox Dimensions Inches (mm)
Fig. 2
FACP
Box has one threaded 1/2" conduit entrance
3 3/8”
(86)
5 3/4”
(146)
3 3/8”
(86)
1 5/8”
(41)
4 1/4”
(108)
4 1/4” (108)
3 3/8” (85.9)
DWG# 776-2
2”
AL-BBD
5”
(127)
_
+
To Next
Device or
End-of-Line
Resistor
Installation
1. The bell shall be installed in accordance with NFPA 13, 72,
or local AHJ. The top of the device shall be no less than 90"
AFF and not less than 6" below the ceiling.
2. Remove the gong.
3. Connect wiring (see Fig. 3).
4. Mount bell mechanism to backbox (bell mechanism must be
mounted with the striker pointing down).
5. Reinstall the gong (be sure that the gong positioning pin, in
the mechanism housing, is in the hole in the gong).
6. Test all bells for proper operation and observe that they can
be heard where required (bells must be heard in all areas as
designated by the authority having jurisdiction).
)
(51
Failure to install striker down will prevent bell from operating.
SEV
SYSTEMS
Safe Environmental Choice
®
info@SEVOSystems.com
Phone +1.913.677.1112
Fax +1.913.384.5935
14824 West 107th St.
Lenexa, KS 66215 USA
www.SEVOSystems.com