AQUAZIP ADV
Waterproofers
Two-component cement-based
application by roller and brush
highly
elastic
waterproof
coating
for
Composition
AQUAZIP ADV is a two-component elastic waterproof coating made from cement, graded sand, chemical additives
and synthetic polymers in emulsion to improve the workability, adhesion and flexibility
Standard requirement
EN 14891 standard
Impermeability to water under pressure
(1.5 bars for 7 days of positive lift)
No penetration
> 0.75 mm
Crack bridging ability at 23° C
2
Initial tensile adhesion strength
> 0.5 N/mm
Tensile adhesion strength after water immersion
> 0.5 N/mm2
Tensile adhesion strength after heating
> 0.5 N/mm2
Tensile adhesion strength after freeze-thaw cycles
> 0.5 N/mm2
Tensile adhesion strength after immersion in alkaline
water
> 0.5 N/mm2
Component A
Appearance
Specific weight
Dry residue
Grey powder
1300 g/l
100%
Component B
Appearance
Specific weight
Dry residue
White latex
1010 g/l
53%
Technical specifications
Mix ratio
2 parts Comp. A and 1 part Comp. B
Specific weight of wet mortar
approx. 1600 kg/m3
Pot life
1 hour
pH
> 12
Application temperature
from +5 °C to +35°C
Yield for application by roller or brush
approx. 1.6-2 kg/m per mm in thickness depending on
application conditions (by hand or machine)
Maximum thickness
2 mm total, with 1 mm per coat
Time before laying tiles with adhesive
minimum 5 days at +20°C and 65% relative humidity
2
Fassa S.p.A. - Via Lazzaris, 3 - 31027 Spresiano (TV) - www.fassabortolo.com
Product data sheet: AQUAZIP ADV - Edition 09/2012
AQUAZIP ADV
Waterproofers
Use
AQUAZIP ADV is used to waterproof and protect concrete objects, including objects under load, against penetration of
gases such as CO2 and de-icing salts; it is also used as waterproof elastic skim coat on plaster with tiny cracks,
cementitious floor screeds, ceramic floors, plasterboard and marine plywood, before applying ceramic tiles.
Substrate preparation
The application surface must be free of dust, dirt, etc. Any traces of oil, grease, wax etc. must be removed beforehand,
as well as any powdery or loose sections. Before applying AQUAZIP ADV moisten absorbent surfaces with water.
If applying on an existing floor, before using the product make sure that the existing covering is solid and clean.
Mixing and application
For application by hand, add one 10 kg pack of AQUAZIP ADV Comp. B to each 20 kg sack of AQUAZIP ADV Comp. A
and mix by stirrer at low speed until obtaining a uniform and smooth mix: the mix obtained is workable for around 1 hour.
Apply the coating by brush or roller to a maximum thickness of 1 mm. Apply the second coat only when the first coat has
hardened (after around 5 hours) to a maximum thickness of 1 mm. The product can also be applied by trowel. AQUAZIP
ADV can be applied using a plaster sprayer, in the same ways as for application by hand.
If applying the product on especially stressed or cracked structures, in the first coat embed alkali resistant fibreglass mesh
or a layer of nonwoven fabric, using a trowel.
Tile the surface with AD8+DE80, AZ59, AT99, or alternatively, if quick setting products are required, AQ60 and FASSATEC
2, in any case at least 5 days after application of AQUAZIP ADV, in normal humidity and temperature conditions.
Warnings



The coating should be protected against rain, frost and quick drying.
If applying at high temperatures and above all with considerable ventilation, protect the surface with damp cloths.
Wash all the equipment before the product sets. Otherwise, residues of the product must be removed
mechanically.
AQUAZIP ADV must only be used in its original state, without the addition of other materials.
Supply


Component A: special sacks with protection against moisture, approx. 20 kg
Component B: buckets, approx. 10 kg
Storage


Component A: store in a dry place for a maximum of 12 months.
Component B: protect from frost; if stored in a suitable environment and sealed in its original packaging, the
material has a shelf life of 12 months.
Quality
AQUAZIP ADV undergoes accurate and continuous checks in our laboratories. The raw materials used are carefully
selected and checked.
The above information refers to laboratory testing; in practical applications on site this may differ considerably according to the conditions in which
the material is applied. The user must verify that the product is suitable for the intended application, taking all responsibility for its use. Fassa
reserves the right to make any technical modifications without prior notice.
Fassa S.p.A. - Via Lazzaris, 3 - 31027 Spresiano (TV) - www.fassabortolo.com
Product data sheet: AQUAZIP ADV - Edition 09/2012