International Journal on Recent Technologies in Mechanical and Electrical Engineering (IJRMEE) ISSN: 2349-7947
Volume: 3 Issue: 2 005 – 009
_______________________________________________________________________________________________
Department of Electrical Engineering
Department of Electrical Engineering,
Department of Electrical Engineering,
Jamia Millia Islamia
New Delhi, India harun_ash@yahoo.com mdsaood@hotmail.com
Indian Institute of Technology Delhi
New Delhi, India ikhlaqb@gmail.com
Aligarh Muslim University
Aligarh, U.P, India sjasghar@gmail.com
Abstract
—Input voltage control has been used for improvement of power factor in grid-connected induction generators. However, this method reduces the efficiency drastically due to high input current. Moreover the control range is also limited. In the proposed schemes, both voltage control and slip control are employed together to control the efficiency and power factor. Scheme-I is used to tap maximum power from the wind turbines using wound rotor induction generators. It also controls the local bus voltage and maximizes efficiency of the generator. At an optimum voltage, slip control is employed such that the output is maximized at every operating point. The scheme-II is used for maximizing the power factor. An optimum grid voltage is applied to the generator and the effective rotor resistance is varied to operate it at desired slip for the optimum power-factor. Here the power-factor hence the reactive power demand remains nearly constant throughout the range of speed variation.
These schemes are very useful for wind based power generation where wind speed varies abruptly over wide range. For this purpose personalcomputer (PC) based ac regulator is employed. The proposed controllers work satisfactorily even at dynamic conditions.
Keywords Ac regulators; induction generators; peak power point tracking; power factor control; voltage control; voltage rise; wind power
__________________________________________________*****_________________________________________________
I.
I NTRODUCTION
Both deteriorating environmental conditions and depletion of fossil fuels have increased interest in renewable energy generation technologies. A rapid development is taking place in the field of wind energy conversion system (WECS). For this purpose, two types of wind turbines are used, namely fixed speed turbine and variable speed turbines. A fixed speed system is simple and reliable but it is a sub-optimal performance system.
If the fixed speed turbines are directly connected to induction generators, the system suffers from the following disadvantages
1) The wind turbine output power varies as the cube of wind speed, and the wind turbine can deliver maximum output power only at a particular rotor speed as shown in Fig.1.
Therefore a significant amount of power is lost for operation at speeds other than optimum speeds. Thus, it is under-utilization of resources.
2) At different wind speed, the operating point is not generally the maximum efficiency point of the generator.
3) Connection of an embedded generator to a weak grid may result in unacceptably higher magnitude of voltage at the bus to which it is connected.
As compared to fixed speed systems, the variable speed systems improve the dynamic behavior of the turbine, reduce mechanical stresses, improve the power quality and tap a higher amount of power. However, the main disadvantage is the requirement of a costly and complex electrical control system (power electronic controller). For variable speed
WECS, the robustness, low maintenance and relative cheapness of induction machines are well known in medium power applications [1-3].For this system a power electronic converter is connected between the stator circuit and the grid which is designed for the rated power of turbine. However, if the converter is put in the rotor circuit the converter rating is reduced up to half of the system power rating.
Li ne s of
c on po w st an t er
Locus of maximum power delivery
Turbine Torque/speed curves for increasing wind speed
Turbine rotational speed
Fig.1: A family of torque-speed characteristics of generator and wind turbine.
Also with the development in the field of electrical machine designing, slip ring machine ruggedness, the reliability of the wound rotor machine has matched the squirrel cage machine.
Thus, the latter system proves to be more economical in many cases [1].
To extract maximum power from the WECS, various types of power electronic converters have been employed between the generator and the grid. Hansen et al. list some of these topologies [4-6]. A number of schemes are working on these topologies. A comparative study of gear-based schemes was also carried out [1][7-9]. Recently it has been reported that a particular control strategy for variable speed cage machines has enhanced the performance [10-13].
5
IJRMEE | February 2016, Available @ http://www.ijrmee.org
_______________________________________________________________________________________

International Journal on Recent Technologies in Mechanical and Electrical Engineering (IJRMEE) ISSN: 2349-7947
Volume: 3 Issue: 2 005 – 009
_______________________________________________________________________________________________
In this work, two control schemes are proposed using both stator voltage control and rotor slip control methods together.
In the first scheme the output power is maximized by efficiency improvement of induction generator and simultaneous tapping of maximum output power from the prime mover. Also, the voltage rise problem related to weak grids and embedded systems are also dealt with. In the second scheme the power factor of the WECS is optimized using the same converter. A personal computer (PC) based controller has been developed and tested for the system.
This paper consists of six sections. Section 1 describes the brief introduction. Section 2 presents the proposed approach.
Section 3 presents the system description. Section 4 presents the control methods. Section 5 presents the realization and experimental Results. Finally, Section 6 provides some important conclusions that we have drawn from this study.
II.
P ROPOSED A PPROACH rated for all the wind conditions thereby maximum power factor is tracked. Both maximum output power and maximum power factor tracking of grid connected induction generator are achieved.
III.
S YSTEM D ESCRIPTION
Simple block diagram of the proposed system is shown in Fig.
3. The generator torque m g velocity
 t varies as the square of the angular of the turbine shaft. It is expressed as
m g
= K .
 t
2
(1)
For optimum operation, the generator torque is controlled. The optimum generator torque is given by
m gOPT
= K
OPT
.
 t
2
(2)
The parameter K
OPT
is given by
K
OPT
= 0.5 C pMAX
C p
.

.
A .
(R /

MAX
)3 (3)
is power coefficient of the turbine,

is air density, R is the radius of the rotor of the turbine, A is the rotor swept area of the turbine and

, the tip speed ratio with wind speed

is
The proposed approach is based on the two improved schemes. Fig. 2 shows the proposed approach implementation steps which uses simulated and experimental results.
MOPT
No
Scheme-I
Voltage control
Is
Torque
requirement
Sufficient (such that generator is operated at a torque at maximum power point such that machine losses are minimum
Read input data
ω t
, v, V, R, I m
, I
R
Applying improvement schemes
Scheme-II
Reduce voltage such that the current become rated for all the wind conditions
MPFT defined as

= (
 t
.
R /

) (4)
C pMAX
and

MAX
and turbine parameters are generally provided by the manufacturers.
For a particular wind speed, the operating point of the wind turbine i.e., mechanical output power and rotor speed is determined by the intersection point of the prime-mover
(turbine) characteristic and the load (induction generator) characteristic. At a particular wind speed, a personal computer based feedback control system is developed to determine the optimum grid voltage to be applied and the rotor resistance to be added. The sampling period of the feedback is so chosen that it is more than the response time of the speed loop (the sampling period is taken five times the speed loop time constant of the system).
Yes
Resistance control
(add rotor resistance)
Is
I≈rated for all wind
No
No
Is
Generator characteristics shifted to required speed for the particular
wind
Yes
Tracked maximum output power
Both Maximum power output and maximum power factor tracking of grid connected induction generator are achieved
Yes
Tracked maximum power factor
Fig. 2: Schematic diagram of proposed scheme
Read the input parameters and apply the improvement schemes. In the first scheme, on torque speed curve first match the torque required using voltage control such that the generator is operated at a torque at maximum power point such that the losses are minimized. Then add rotor resistance
(Resistance control) such that the generator characteristics are shifted to required speed for the particular wind. In the second scheme, stator voltage is varied such that the current become
Fig. 3: A simple block diagram of the proposed control scheme
IV.
C ONTROL M ETHODS
Three control methods are adopted here for controlling the output power, power factor and voltage rise. In this section each of these is described in detail.
6
IJRMEE | February 2016, Available @ http://www.ijrmee.org
_______________________________________________________________________________________

International Journal on Recent Technologies in Mechanical and Electrical Engineering (IJRMEE) ISSN: 2349-7947
Volume: 3 Issue: 2 005 – 009
_______________________________________________________________________________________________
A.
Maximum output power tracking (MOPT) system
(Scheme-I) principle is extended here for induction generators to achieve the maximum power factor at any speed. Thus an optimum voltage is applied and the external rotor resistance is varied
If the stator voltage of an induction motor is controlled, the input power/efficiency of the motor varies [14]. It was reported earlier by the authors that there is always an optimum voltage for every torque, at which the efficiency is maximum
[15-17].The same principle is extended here for induction generators to achieve the maximum efficiency at different torques. Hence, there is a minimum power loss point for every speed of the wind turbine as shown in Fig. 1. For an induction machine it can be explained with the help of the vector diagram as shown in Fig.4. The maximum efficiency
(minimum losses) of an induction-generator for a given wind torque are found by the following proposed function of the such that the power-factor remains maximum throughout the speed range of the wind turbine. At this reduced voltage the current limits are also not violated heavily. The reduced stator or grid voltage is so chosen that the power factor is made as close to unity as possible. However it is ensured that the stator and the rotor current of induction-generator do not increase beyond a certain limit for every wind speed (i.e.120% of rated current even for highly inductive loads). It is observed that the power-factor remains almost constant throughout the operating range. A constant, low-value capacitive compensation (kVAR) is enough for any wind speed to keep the power factor close to stator current as given by
I s


(aI m
) 2 

I
 r a

2
1

2
(5) unity. However, the cut-in speed has to be increased marginally due to the reduced input voltage from the grid.
Where,
I s
= stator current a = Ratio of the reduced voltage to the rated voltage,
I
I m r
= magnetizing current at the rated voltage and

= reflected rotor current at a given wind torque
From the above equation, the speed-optimum voltage characteristic of the induction generator is simulated. An optimum voltage is found for each wind speed (torque) such that the efficiency becomes maximum. Now, for any wind speed, a pre-calculated optimum input voltage is applied to the generator using an ac regulator such that the efficiency becomes maximum. A pre-calculated external resistance is also added in the rotor circuit corresponding to the speed. Thus the wind turbine delivers maximum output power. Also the input power factor improves throughout the useful speed.
I r
I s
I s
I r
(a)
(b)
I m
I m a
1
V
C.
Voltage Rise
Connecting an embedded generator to an existing distribution network may lead to several local problems such as steadystate voltage rise, voltage dip at the generator cut-in, etc. This is due to the fact that active voltage regulation is generally not provided beyond the last HV sub-station. A number of methods are employed to limit the steady-state voltage rise.
1) Reduction of Line Impedance:
Line impedance may be reduced either by physically moving the connection point closer to the source substation or increasing the size of existing distribution feeder.
(2) Load management can be done either by connecting a large load, sufficient to cover the rise in the voltage due to increase in the output power of the embedded generator or by properly fast switching a number of small loads. [19][20].
(3) Reduction of active power of the turbine:
In order to maintain satisfactory voltages, the generation
(output) may be reduced at critical times, by adjusting the wind turbine set point or disconnecting some wind turbines as desired [21].
(4) Regulating the reactive power of the local bus bar. This can be obtained by use of static VAr compensators, switched capacitor banks etc.
(5) Power factor control of the wind generator; this is achieved here by the use of an ac regulator. In the proposed work
(scheme-II) an alternative method is employed. Here the power factor of the induction generator is controlled to its maximum.
I r a
3
V a
2
V
V.
REALIZATION AND EXPERIMENTAL RESULTS
I s I m
(c)
Fig.4. The stator current variations with decreasing stator voltage
B.
Maximum power factor tracking (MPFT) system
(Scheme-II)
It was found earlier that there is always an optimum voltage at which the input power factor remains high irrespective of speed variations [18]. It was achieved from the modified characteristics of wound rotor induction motor by applying both stator voltage control and slip control. Again this
A personal computer based feedback control system has been developed and Fig. 5 shows the complete control scheme. It consisted of the following parts:
1) Synchronizing circuit: It generates positive pulses at zero crossing instants of the grid voltage. A zero crossing detector is used for this purpose.
2) Interfacing system: A suitable interfacing system is connected to receive the input (wind speed) and send output
(triggering signals). An A to D converter is used to receive the output voltage of the tachogenerator corresponding to the wind speed.
7
IJRMEE | February 2016, Available @ http://www.ijrmee.org
_______________________________________________________________________________________

International Journal on Recent Technologies in Mechanical and Electrical Engineering (IJRMEE) ISSN: 2349-7947
Volume: 3 Issue: 2 005 – 009
_______________________________________________________________________________________________
3) Driver and buffer circuit: To isolate the control circuit from the power circuit (thyristor pairs of ac regulator), driver and buffer circuits are used.
4) Software: Both assembly language and C language based programming are carried out to generate triggering pulses with proper control strategy.
3-phase ac supply
AC regulator
δ
Control
IG
N
Tachogenerator f
ZCD
Both simulated and experimental results are shown together for conventional as well as proposed techniques (Fig. 7 and
Fig. 8). The first curve and the second curve are related with the conventional stator voltage control and conventional rotor resistance control respectively. The third curve is related with the proposed method (scheme-I), where both stator voltage and rotor resistance/slip are controlled. It is evident that the efficiency and output power remains high throughout the range of speed variations. Thus maximum output power tracking (MOPT) is achieved. The forth (MPFT) curve clearly shows a high power factor operation throughout the operating range. Also, as the controller is very fast it works satisfactorily in dynamic conditions.
P.T
P.T
ZCD
Personal computer
Fig. 5: Complete Control Scheme
Waveforms in Fig.6 show the change of voltage and current with reducing wind speed. Speed –efficiency and Speed – power factor experimental values of proposed system are shown in table-1 and table-2 respectively.
Speed(rpm)
Fig. 7: Speed - Efficiency variations for conventional voltage control, MOPT
& MPFT.
(a) Voltage Waveform
(b) Current waveform
Fig. 6: Waveforms show the change of (a) voltage and (b) current with reducing wind speed. Lower trace shows the change in tacho-generator voltage due to wind speed.
Speed (rpm)
Fig. 8: Speed – Power factor variations for conventional voltage control,
MOPT & MPFT
8
IJRMEE | February 2016, Available @ http://www.ijrmee.org
_______________________________________________________________________________________

International Journal on Recent Technologies in Mechanical and Electrical Engineering (IJRMEE) ISSN: 2349-7947
Volume: 3 Issue: 2 005 – 009
_______________________________________________________________________________________________
VI.
C ONCLUSION system,‖ IEEE Trans. Energy Convers., vol 18, no. 1, pp. 163-
168, Mar. 2003.
Here both stator voltage control and slip control are employed simultaneously to improve the efficiency as well as the power factor of the wind turbine based power generation.
The efficiency and power factor of a grid connected induction generator are greatly enhanced. Two schemes are proposed and verified satisfactorily with practical results. Scheme-I offers better efficiency and better input (line) current with an appreciable improvement in power factor. Scheme-II offers better power factor throughout the operating range of the speed.
In scheme II, the efficiency is better as compared to simple voltage reduction method. Moreover, it is comparable to the efficiency of the conventional rotor resistance control method.
The control schemes are found to be working satisfactorily even under dynamic conditions of wind speed variation. The proposed schemes are useful for small and medium power embedded applications because of their simplicity and low cost.
A PPENDIX
Wound Rotor Induction Machine Data:
[8] Chiung Hsing Chen, Chih-Ming Hong and Fu-Sheng Cheng,
―Intelligent speed sensor less maximum power point tracking control for wind generation system,‖ Electrical Power and
Energy Systems, vol. 42, pp. 399–407 May, 2012
[9]
S. Abdeddaim and A. Betka, ―Optimal tracking and robust power control of the DFIG wind turbine,‖ Electrical Power and
Energy Systems, vol. 49, pp. 234–242, Feb. 2013.
[10] M.G. Simoes and B.K. Bose, ―Fuzzy logic based intelligent control of a variable speed cage machine wind generation system,‖ IEEE Trans. Power Electron., vol. 12, no. 1, pp. 87-95,
Jan. 1997.
[11]
M. Karrari, W. Rosehart and O.P. Malik, ―Comprehensive control strategy for a variable speed cage machine wind generation unit,‖ IEEE Trans. Energy Convers., vol 20, no. 2, pp.
415-423, June. 2005.
[12] B. Rabelo and W.Hofmann ―Control of an optimized power flow in wind power plants with doubly-fed induction generators,‖ in
Proc of IEEE 2003, pp.1563-1568.
1.5kW, 415V, 50Hz, six poles, three phases;
Stator: 415V, star connected, 3.5A;
Rotor: 120V, star connected, 7.2A;
[13] Elkhatib Kamal, Abdel Aitouche , Reza Ghorbani and Mireille
Bayart , ―Robust nonlinear control of wind energy conversion systems,‖ Electrical Power and Energy Systems, VOL. 44, PP.
R EFERENCES
202–209,Aug. 2012
[14]
N.Mohan. ―Improvement in energy efficiency of induction
[1]
R. Datta and V.T. Rangnathan, ―Variable-speed wind power motor by means of voltage control,‖ IEEE Trans. on PAS, Vol. generation using doubly fed wound rotor induction machine – a comparison with alternative schemes,‖ IEEE Trans. Energy
Convers., vol. 17, no. 3, pp. 414-421, Sep. 2002.
[2]
H.T. Jadhav and Ranjit Roy, ―A comprehensive review on the grid integration of doubly fed induction generator,‖ Electrical
PAS-99, pp.1466-1471, July-Aug, 1980.
[15]
Mohamed Orabi, ―Efficient performances of induction generator for wind energy conversion,‖ in Proc. Of IEEE Industrial
Electronics Society, 2004, pp.838-843
[16] G.K.Dubey, ―Power Semiconductor Controlled Drives,‖Prentice
Power and Energy Systems, vol. 49, pp. 8–18, Jan. 2013.
[3] Abdullah Asuhaimi B. Mohd Zin, Mahmoud Pesaran H.A.,
Azhar B. Khairuddin, Leila Jaha shaloo and Omid Shariati, ― An over view on doubly fed induction generators controls and
Hall publishing; 1986.
[17]
H. Ashfaq and M.S. Jamil Asghar. ―Speed Control of Wound
Rotor Induction Motors by AC Regulator Based Optimum
Voltage Control.‖ in Proc. 2003 IEEE International conference contributions to wind based electricity generation,‖ Renewable and Sustainable Energy Reviews, vol 27, pp. 692–708, Nov.
2013.
[4]
L.H. Hansen, ―Generators and power electronics technology for on Power Electronics and Drive Systems (PEDS), pp. 1037-
1040.
[18] H.Ashfaq, ―Development of ac regulator based controller for speed control of wound rotor induction motors‖, M.Tech.. wind turbines,‖ in Proc. 2001 IEEE conf. of Industrial
Electronics Society, pp. 2000-2005. dissertation, AMU, Aligah, India.
[19] N.C. Scott, D.J. Atkinson, and J.E. Morrell, ―Use of load control
[5] R,C.Bansal, T.S Bhatti and D.P.Kothari. ―Biblography on The
Application of Induction Generators in Nonconventional Energy
Systems‖, IEEE Transactions on Energy conversion, Vol 18, No.
3, pp 433-439, Sep 2003.
[6] S.S Murthy, B.P Singh, C.Nagamani, and to regulate voltage on distribution networks with embedded generation,‖ IEEE Trans. Power Syst., vol. 17. no. 2, pp. 510-
514, May 2002.
[20]
J.W. Smith and D.L. Brooks, ―Voltage impacts of distributed wind generation on rural distribution feeder,‖ in Proc. Transm.
K.V.V.Satayanarayana, ―Studies on the use if conventional
Induction motors as self excited induction generators,‖ IEEE
Distrib. Conf. Expo., vol. 1, 2001, pp. 492-497.
[21]
S. Hari, P. Trevor, and I. Syed, ―Effect of pitch control and
Transactions on Energy conversion, Vol 3, No. 4, pp 842-848.
Dec 1988.
[7]
R. Datta, and V.T. Rangensthan, ―A method of tracking the peak power conditioning on power quality of variable speed wind turbine generators,‖ in Proc. Australasian Universities Power
Engineering Conf., 2001, pp. 95-100. power point for a variable speed winds energy conversion
9
IJRMEE | February 2016, Available @ http://www.ijrmee.org
_______________________________________________________________________________________