•
•
•
Studio Design Specifications – Recent Updates
May 2014 – Added general clarification to specifications, replaced specs on lighting
fixtures with LED, added Regency Lighting supplier contact info, updated Patcraft
flooring representative contact info,
April 2014 – Added Highland Forest LVT to replace previous spec, stipulated factory
black ceiling tiles in place of P2-painted throughout studio except where noted,
clarified door hardware in specific applications, specified all-black trim kits for
recessed lighting, added flooring representative contact information, specified
baseboards by-room, standardized interior door technical specs and removed
option for upgrade, added standard power/data in break room for wall-mounted
computer monitor, specified low-voltage punch down for linen room, added
upgradeable plumbing fixtures and dispensers of restroom consumables, added
specs for optional dedicated office, added specs for optional storage closet
March 2014 – General Update – reconciled references and added spec sheets where
applicable
Studio Design
Specifications
Total Studio Area: 1600-1800 square feet
Lobby: 280+ sq ft
o
Dimensions
o
o
14’ depth recommended minimum
Walls
o
Wall separating lobby from rest of the space must be built full height to underside of roof deck
o
5/8” Gyp. board standard
o
Sound batt insulation installed in all walls
o
For additional noise reduction add 5/8” sound board (Gold Bond® brand SoundBreak® or
equal) in lieu of, or for best results, in addition to 5/8” sheet rock
o
Drywall level 4 finish or greater - Hamilton prep coat recommended
 Paint
o
Primary paint – P1 : Sherwin Williams #7527 Nantucket Dune (see spec – pg. 35)
o
Accent Paint – P2 : Sherwin Williams #6083 Sable (see spec – pg. 36)
o
All paints to be semi-gloss or egg shell.
o
Accent wall painted P2. Accent wall cannot be behind reception counter (recommend smallest
wall.) All other walls P1.
 Floor
o
Contact Todd Stordahl, Patcraft Commercial Flooring Specialist, 303.775.1155 or
todd.stordahl@patcraft.com
o
LVT (see spec – pgs. 14 – 15)
o
Franchise owner chooses between Ashwood, Walnut, or Barnwood finish. No substitutions.
o
4” vinyl plank.

Manufacturer: Patcraft
•
o
Series: Highland Forest – 1200V Type B (Embosse)
o
Ashwood – 20100
o
Walnut – 20700
o
Barnwood – 20730
6” pine baseboard painted P2
 Ceiling
o
Black 2’x2’ acoustical tiles and grid (see spec – pg. 11)
o
Factory black suspending ceiling tile and grid
Page 1 of 52
Elements Massage Studio Design Specifications 5/2014

Armstrong - 24”x24”x5/8” Fine Fissured Tech Black inlay tiles or equal

Black Mains – Armstrong 15/16” Black 7300 or equal

Black Cross Tees – Armstrong XL7328-BL or equal
o
All HVAC diffusers, registers, grilles etc. Titus finish 84 factory black or equal
o
10’-0” A.F.F. minimum – Support Center approval required if not standard
o
Sound batt insulation installed above suspended ceiling – 6¼”/R19 or greater recommended
 Lobby door: 3’x7’x1-3/4” full light/rain glass, MDF paint grade, Masonite or equal painted P2 semi-gloss
o
Knockdown hollow metal frame factory black
o
Push/pull non-latching passage dummy leverset in brushed nickel
o
Hydraulic door closer
 Power/data
o
(1) duplex outlet per wall, per corner
o
(2) quad outlets plus (2) data at reception desk
o
Additional outlets as needed per support center, franchise owner, or electrical code
 Lighting
o
Contact Brandon Melton, National Account Executive for Regency Lighting direct:
800.284.2024 ext. 4240, mobile: 303.748.8971, Email brandon.melton@regencylighting.com *Please note, all decorative light fixture specs are subject to change in the near future
o
(3) pendant lights (see spec – pgs. 16 – 17) on dedicated dimmer switch over the front desk

Primary: Besa Lighting 1KX-412480-LED-BR
•
Cierro LED Pendant 1KX in 412480 Amber Matte with 10W GU-24 LED lamp
(included)
o
6” LED recessed can lights on dimmer switch with black baffle and trim ring

Fixture: Elite B6IC-LED-14W-120V-DIM-FL-30K-AT (see spec – pg. 20)
•

Trim Kit: Elite L631P-BK (see spec – pg. 21)
•
o
6” New Construction IC Housing
Phenolic Stepped Baffle
(3) 6” LED recessed downlights on dimmer switch with black wall washer trim kits to shine on
logo behind front desk

Fixture: Elite Lighting HH6IC-LED-1200L-DIM10-120MD (see spec – pg. 22)
•

Trim Kit: Elite Lighting HH6-6507-MB-MB (see spec – pg. 23)
•
o
Architectural High Lumen LED IC Downlight
Wall Wash Reflector with Diffuse Lens – Matte Black Trim/Black Color Ring
Ceiling fan (optional)

Emerson 52” CF705BS fan or equal (see spec – pg. 12 – 13)

GC to give allowance if alternate fan requested by franchise owner
Page 2 of 52
Elements Massage Studio Design Specifications 5/2014
 Pass through window (rain glass) installed between desk area and hallway or break room if applicable
o
Dimensions: Minimum 16”x 24”, maximum 24”x 24”
o
Lateral sliding pane on aluminum track with thumb-hold
Hallway
 Walls
o
5/8” Gyp. board standard
o
Sound batt insulation installed in all walls
o
For additional noise reduction add 5/8” sound board (Gold Bond® brand SoundBreak® or
equal) in lieu of, or for best results, in addition to 5/8” sheet rock
o
Drywall level 4 finish or greater - Hamilton prep coat recommended
o
Painted P1 Sherwin Williams #7527 Nantucket Dune (see spec – pg. 29)
 Flooring
o
Contact Todd Stordahl, Patcraft Commercial Flooring Specialist, 303.775.1155 or
todd.stordahl@patcraft.com
o
Carpet – CP1 (see spec – pgs. 30 – 31)
o
2’ x 2’ Carpet Tile, installed with ¼ turn layout pattern

Manufacturer: Patcraft
•
Series: #10096 Tweed Modular
o
o
Color: #96102 Houndstooth
6” pine baseboard painted P2
 Ceiling
o
Black acoustic ceiling tile and grid (see spec – pg. 11)

All HVAC diffusers, registers, grilles etc. Titus finish 84 factory black or equal

Same spec as lobby ceiling
o
10’-0” A.F.F. minimum – Support Center approval required if not standard
o
Sound batt insulation installed above suspended ceiling – 6¼”/R19 or greater recommended
 Music System
o
o
Speaker (see spec – pg. 32)

Atlas C-series Model SD72 or equal

Black, factory or painted
Volume Control (see spec – pg. 33 – 34)

Atlas AT35D or equal

White or Ivory plate

Dedicated volume control in each room
 Power (per code)
 Lighting
Page 3 of 52
Elements Massage Studio Design Specifications 5/2014
o
o
6” LED Recessed Can Lights (see spec – pg. 20 – 21) with black baffle and trim ring

Every 10’-0” or per code

Dedicated switch

Same spec and source as lobby recessed cans
Wall Sconces (see spec – pg. 18)

Primary: Seagull Lighting 41585-710
•

o
One-Light Wall/Bath Sconce in Burnt Sienna with Café Tint Glass with LED Lamp
Dedicated dimmer switch
Installed alternating walls, between massage rooms or every 12’-0”, 82” to center A.F.F.
•
See hallway elevation example pg. 21
Massage Rooms: 96+ sq ft
 Dimensions
o
Minimum 8’ x 12’
o
Couples’ Room Minimum 12’ x 14’
o
Less than minimum requires Support Center approval
 Walls
o
5/8” Gyp. board standard
o
Interior partitions to go ~6” above suspending ceiling, 3-5/8” metal studs, 3” high quality sound
batt insulation, and 5/8” drywall
o
Partitions between massage rooms and lobby/break room/bathroom/linen framed full height to
underside of roof deck

For additional noise reduction may substitute Gold Bond® brand SoundBreak® or equal in
lieu of 5/8” drywall
o
Drywall level 4 finish or greater - Hamilton prep coat recommended
 Paint
o
Primary paint – P1 : Sherwin Williams #7527 Nantucket Dune (pg. 35)
o
Accent Paint – P2 : Sherwin Williams #6083 Sable (pg. 36)
o
All paints to be semi-gloss or egg shell.
o
One accent wall in each massage room painted P2 – shortest wall; not the wall with the wall
sconce. P1 all other walls.
 Floor
o
CP1 (see spec – pg. 30 – 31)

o
Same spec and source as hallway floor
4” Vinyl Cove Base (see spec – pg. 39 – 40)

Roppe – 4”
•
700 Series - 619 Java
Page 4 of 52
Elements Massage Studio Design Specifications 5/2014
 Ceiling
o
Black acoustic tile and grid (see spec – pg. 11)

Same spec as lobby ceiling

All HVAC diffusers, registers, grilles etc. Titus finish 84 factory black or equal
o
Air diffusers positioned not directly above massage table but offset toward foot of the table
o
(1) black speaker (see spec – pg. 32) located in middle of the room w/ dedicated volume control
o
9’-0” A.F.F. minimum
o
Sound batt insulation installed above suspended ceiling – 6¼”/R19 or greater recommended
 Doors
o
3’x7’x1-3/4” minimum, solid core, paint grade, Masonite or equal, painted P2 semi-gloss
o
Knockdown hollow metal frame factory black
o
Passage leverset in brushed nickel
o
Hydraulic door closer
 Power
o
(1) duplex outlet (standard height A.F.F.) located on the wall adjacent to the door
o
(1) duplex outlet (standard height A.F.F.) located in corner opposite the door.
o
(1) duplex outlet, recessed in middle of the floor, for massage table (floor trenching required)
 Lighting
o
o
Wall sconce (see spec – pg. 18) centered on longest wall opposite door

82” A.F.F. to center

Dimmer switch

Same spec and source as hallway sconces
(1) LED recessed can light (see spec – pg. 20 – 21) if required by permit or requested by owner
with switch located next to sconce dimmer and volume control
Break Room: minimum of 150 sq ft
 Break room will need to have room for at least a ¾ size refrigerator and 1-2 person work station with
power and data
 Walls
o
5/8” Gyp. board standard
o
5/8” Green board at wet areas
o
Sound batt insulation installed in all walls
o
Drywall level 4 finish or greater
o
Painted P1
 Floor
o
VCT (see spec – pg. 37 – 38)

Armstrong – 12”x12” tile
Page 5 of 52
Elements Massage Studio Design Specifications 5/2014
•
o
51830 Cottage Tan
4” Vinyl Cove Base (see spec – pg. 39 – 40)

Same spec as Massage Rooms
 Ceiling
o
Standard white 2’x2’ suspending ceiling tile and grid (see spec – pg. 11)

Armstrong Prelude White 24”x24”x5/8” tiles or equal

Armstrong Mains 15/16” 7300XR-White or equal

Armstrong Cross Tees XL7328-WH or equal
o
All diffusers, registers, & grills to be white Titus finish 26
o
9’-0” A.F.F. minimum
o
Sound batt insulation installed above suspended ceiling – 6¼”/R19 or greater recommended
 Power
o
Per code - GFCI outlets as required
o
(2) duplex outlets between upper and lower cabinets
o
(2) duplex outlets near work station with data
o
(1) duplex outlet with data above or near work station 72” A.F.F. or as required for wall-mounted
computer/tv monitor
o
Additional outlets at support center and/or franchise owner
 Lighting
o
Contact Brandon Melton, National Account Executive for Regency Lighting direct:
800.284.2024 ext. 4240, mobile: 303.748.8971, Email brandon.melton@regencylighting.com
o
2’x2’ LED troffers and lighting on dedicated switch (see spec – pg. 24)
 Door
o
3’x7’x1-3/4” minimum, solid core, paint grade, Masonite or equal, painted P2 semi-gloss
o
Knockdown hollow metal frame factory black
o
Push/pull non-latching passage dummy leverset in brushed nickel
o
Hydraulic door closer installed
Linen Room: 40-80 sq ft (determined by the number of massage rooms)
 Walls
o
5/8” Gyp. board standard
o
5/8” Green board if applicable/required
o
Sound batt insulation installed in all walls
o
Level 4 finish or greater, Painted P1
 Ceiling
o
Standard white 2’x2’ suspended ceiling tile and grid (see spec – pg. 11)

Same spec as break room
Page 6 of 52
Elements Massage Studio Design Specifications 5/2014
o
9’-0” A.F.F. minimum
o
Sound batt insulation installed above suspended ceiling – 6¼”/R19 or greater recommended
 Floor
o
VCT (see spec – pg. 37 – 38) and 4” vinyl cove base (see spec – pg. 39 – 40)

same spec and source as break room floor
 Doors
o
3’x7’x1-3/4” minimum, solid core, paint grade, Masonite or equal, painted P2 semi-gloss
o
Knockdown hollow metal frame factory black
o
Push/pull non-latching dummy leverset in brushed nickel
o
Hydraulic door closer installed
 Power
o
(2) GFCI duplex outlets
o
Punch down (low voltage)
o

Dynacom pre-wired 66 block with 12 2-pair RJ11 Jacks, Model DY-66BM12 – 2 or equal

Separate 12-port CAT6 patch panel Intellinet Model #560269 or equal (for data)
220v dryer outlet (optional)
 Lighting
o
Contact Brandon Melton, National Account Executive for Regency Lighting direct:
800.284.2024 ext. 4240, mobile: 303.748.8971, Email brandon.melton@regencylighting.com
o
2’x2’ LED troffers and lighting on dedicated switch (see spec – pg. 24)
 Plumbing
o
Mop sink and drain (per code)
o
Hot water heater (raised above ceiling ok); minimum 10 gallon
o
Washer hot/cold connection
Utility Room (if required separate from Linen Room)
 Build and furnish all to linen room spec and per Code
(2) ADA Bathroom compliant bathrooms
 Walls
o
5/8” Green board
o
Sound batt insulation installed in all walls
o
For additional noise reduction add 5/8” sound board (Gold Bond® brand SoundBreak® or
equal) in lieu of, or for best results, in addition to 5/8” sheet rock
o
P1 paint above tile
o
Drywall level 4 finish or greater
 Ceiling
o
Hard lid/drywall, painted P1, 8’-0” A.F.F.
Page 7 of 52
Elements Massage Studio Design Specifications 5/2014
o
LED recessed can light, on/off/motion switch

o
Same spec and source as lobby can lights
Quiet operation exhaust fan
 Floor/Tile
o
Franchise owner chooses between light or dark option
o
Manufacturer: Daltile

Series: Fidenza
•
Light: Bianco – FD01 (See spec pg 41 – 44)
o
•
Dark: Café – FD02 (See spec pg 45 – 48)
o
o
Grout: Poly Blend #382 Bone, or equal
Grout: Poly Blend #22 Sahara Tan, or equal
Tile size

Floor – 18”x18”

Wall – 9”x12”

Bullnose – 3”x12”
o
Installed on floor and up walls 48”
o
Bullnose border tile on walls where appropriate
o
Decorative tile trim ok with support center approval, GC to provide allowance
 Doors
o
3’x7’x1-3/4” minimum, solid core, paint grade, Masonite or equal, painted P2 semi-gloss
o
Knockdown hollow metal frame factory black
o
Privacy leverset in brushed nickel
 Fixtures
o
All fixtures must be ADA-compliant, installed per code
o
Water closet per spec (pg. 49) American Standard Cadet Flowise 2467.100 or equal, in white

o
Lavatory per spec (pg. 50 – 51) American Standard Lucerne model 0355.012 or equal, in white

o
upgrade ok with support center approval, GC to provide allowance
upgrade ok with support center approval, GC to provide allowance
Mirror per spec (pg. 52) Bobrick Model B-165-2436 or equal, stainless steel satin finish

upgrade ok with support center approval, GC to provide allowance
o
Grab bars per code
o
Toilet paper and paper towel dispensers per code, upgrades supplied by franchise owner – to
be discussed early enough to prevent unnecessary wall penetrations.
Dedicated Office (if requested by owner)
 Walls
o
5/8” Gyp. board standard
Page 8 of 52
Elements Massage Studio Design Specifications 5/2014

o
Same spec as massage rooms
Partitions between office and lobby/break room/bathroom/linen framed full height to underside
of roof deck, if applicable

For additional noise reduction may substitute Gold Bond® brand SoundBreak® or equal in
lieu of 5/8” drywall
o
Drywall level 4 finish or greater - Hamilton prep coat recommended
 Paint
o
Primary paint – P1 : Sherwin Williams #7527 Nantucket Dune (pg. 35)
o
All paints to be semi-gloss or egg shell.
 Floor
o
CP1 (see spec – pg. 30 – 31) and 4” Vinyl Cove Base (see spec – pg. 39 – 40)

Same spec and source as massage room floor/base
 Ceiling
o
Black acoustic tile and grid (see spec – pg. 11)

Same spec as lobby ceiling

All diffusers, registers, & grills to be black Titus finish 84
o
9’-0” A.F.F. minimum
o
Sound batt insulation installed above suspended ceiling – 6¼”/R19 or greater recommended
 Doors
o
3’x7’x1-3/4” minimum, solid core, paint grade, Masonite or equal, painted P2 semi-gloss
o
Knockdown hollow metal frame factory black
o
Privacy leverset in brushed nickel
 Power
o
Power and Data to support computer terminal, office equipment, or other as requested
 Lighting
o
LED recessed can lighting (see spec – pg. 24) if required by permit or requested by owner with
switch located next to sconce dimmer

Same spec and source as lobby can light
Storage Closet (if required/requested)
 Walls
o
o
5/8” Gyp. board standard

Same spec as massage rooms

Painted P1
Wall-mounted wire shelving – 18” depth minimum, sized to fit
 Ceiling
o
Standard white 2’x2’ suspending ceiling tile and grid (see spec – pg. 11)
Page 9 of 52
Elements Massage Studio Design Specifications 5/2014


9’-0” A.F.F. minimum
Same spec as break room
 Doors
o 3’x7’x1-3/4” minimum, solid core, paint grade, Masonite or equal, painted P2 semi-gloss
o
Knockdown hollow metal frame factory black
o
Privacy leverset in brushed nickel
 Lighting
o
2’x2’ troffers and lighting on dedicated switch (see spec – pg. 24)

Same spec and source as break room lighting
Emergency/Egress Fixtures
 Contact Brandon Melton, National Account Executive for Regency Lighting for Regency Lighting direct:
800.284.2024 ext. 4240, mobile: 303.748.8971, Email brandon.melton@regencylighting.com
 Exit Signage as required by code
o
Exitronix GVEX-U-BP-LB-WH

Thermoplastic combination LED Exit
 Emergency Lights as required by code
o
Exitronix TRL-EM-BR

LED Emergency Light - Bronze
Page 10 of 52
Elements Massage Studio Design Specifications 5/2014
Ceiling Tile
Page 11 of 52
Elements Massage Studio Design Specifications 5/2014
Ceiling Fan
Page 12 of 52
Elements Massage Studio Design Specifications 5/2014
Standard Ceiling Fan Technical Specs from Amazon.com
Page 13 of 52
Elements Massage Studio Design Specifications 5/2014
LVT Flooring
Page 14 of 52
Elements Massage Studio Design Specifications 5/2014
LVT Color Options
Page 15 of 52
Elements Massage Studio Design Specifications 5/2014
Primary Pendant Light
Page 16 of 52
Elements Massage Studio Design Specifications 5/2014
Page 17 of 52
Elements Massage Studio Design Specifications 5/2014
Primary Wall Sconce
Page 18 of 52
Elements Massage Studio Design Specifications 5/2014
Hallway Elevation Example
Page 19 of 52
Elements Massage Studio Design Specifications 5/2014
6” LED Recessed Can Light
Page 20 of 52
Elements Massage Studio Design Specifications 5/2014
6” LED Recessed Can Light Trim
Page 21 of 52
Elements Massage Studio Design Specifications 5/2014
6” LED Recessed Can Downlight – For Accent and Spot Lighting
Page 22 of 52
Elements Massage Studio Design Specifications 5/2014
6” Recessed Downlight Directional Wall Washer Trim
Page 23 of 52
Elements Massage Studio Design Specifications 5/2014
2’x2’ LED Troffer
Page 24 of 52
Elements Massage Studio Design Specifications 5/2014
LED Exit Sign
Page 25 of 52
Elements Massage Studio Design Specifications 5/2014
Page 26 of 52
Elements Massage Studio Design Specifications 5/2014
Page 27 of 52
Elements Massage Studio Design Specifications 5/2014
LED Emergency Light
Page 28 of 52
Elements Massage Studio Design Specifications 5/2014
Page 29 of 52
Elements Massage Studio Design Specifications 5/2014
Carpet
Page 30 of 52
Elements Massage Studio Design Specifications 5/2014
Page 31 of 52
Elements Massage Studio Design Specifications 5/2014
Music Speakers, Volume Controls, and Installation Instructions
Page 32 of 52
Elements Massage Studio Design Specifications 5/2014
Page 33 of 52
Elements Massage Studio Design Specifications 5/2014
Page 34 of 52
Elements Massage Studio Design Specifications 5/2014
Primary Paint P1:
Page 35 of 52
Elements Massage Studio Design Specifications 5/2014
Accent Paint P2
Page 36 of 52
Elements Massage Studio Design Specifications 5/2014
VCT Flooring
Page 37 of 52
Elements Massage Studio Design Specifications 5/2014
Page 38 of 52
Elements Massage Studio Design Specifications 5/2014
Vinyl Cove Base Trim
Page 39 of 52
Elements Massage Studio Design Specifications 5/2014
Page 40 of 52
Elements Massage Studio Design Specifications 5/2014
Light Option Floor Tile
Page 41 of 52
Elements Massage Studio Design Specifications 5/2014
Light Option Wall Tile
Page 42 of 52
Elements Massage Studio Design Specifications 5/2014
Light Option Bullnose
Page 43 of 52
Elements Massage Studio Design Specifications 5/2014
Light Option Grout
Page 44 of 52
Elements Massage Studio Design Specifications 5/2014
Dark Option Floor Tile
Page 45 of 52
Elements Massage Studio Design Specifications 5/2014
Dark Option Wall Tile
Page 46 of 52
Elements Massage Studio Design Specifications 5/2014
Dark Option Bullnose
Page 47 of 52
Elements Massage Studio Design Specifications 5/2014
Dark Option Grout
Page 48 of 52
Elements Massage Studio Design Specifications 5/2014
Toilet/Water Closet
Page 49 of 52
Elements Massage Studio Design Specifications 5/2014
Wall-Hung Lavatory
Page 50 of 52
Elements Massage Studio Design Specifications 5/2014
Page 51 of 52
Elements Massage Studio Design Specifications 5/2014
Bathroom Mirror
Page 52 of 52
Elements Massage Studio Design Specifications 5/2014