AS 4418.1-1996 Supervisory control and data acquisition
advertisement
AS 4418.1—1996 Australian Standard Supervisory control and data acquisition (SCADA)—Generic telecommunications interface and protocol This is a free 6 page sample. Access the full version online. Part 1: General This Australian Standard was prepared by Committee IT/24, Supervisory Control and Data Acquisition. It was approved on behalf of the Council of Standards Australia on 14 June 1996 and published on 5 August 1996. The following interests are represented on Committee IT/24: Agriculture and Resource Management Council of Australia and New Zealand Association of Consulting Engineers Australia AUSTEL Australasian Railway Association Australian Electrical and Electronic Manufacturers Association Australian Fire Authorities Council Australian Gas Association Australian Pipeline Industry Association Australian Security Industry Association AUSTROADS CIGRE AP35 Electricity Supply Association of Australia Fire Protection Industry Association of Australia This is a free 6 page sample. Access the full version online. Telstra Corporation Review of Australian Standards. To keep abreast of progress in industry, Australi an Standards are subject to periodic review and are kept up to date by the issue of amendments or new editions as necessary. It is important therefore that Standards users ensure that they are in possession of the latest editi on, and any amendments thereto. Full details of all Australian Standards and related publications wil l be found in the Standards Australia Catalogue of Publi cations; this information is supplemented each month by the magazine ‘The Australian Standard’, which subscribing members receive, and which gives details of new publications, new editions and amendments, and of withdrawn Standards. Suggestions for improvements to Australian Standards, addressed to the head office of Standards Australia, are welcomed. Notification of any inaccuracy or ambiguity found in an Australian Standard should be made wit hout delay in order that the matter may be investigated and appropriate action taken. This Standard was issued in draft form for comment as DR 95436. AS 4418.1—1996 Australian Standard Supervisory control and data acquisition (SCADA)—Generic telecommunications interface and protocol This is a free 6 page sample. Access the full version online. Part 1: General PUBLISHED BY STANDARDS AUSTRALIA (STANDARDS ASSOCIATION OF AUSTRALIA) 1 THE CRESCENT, HOMEBUSH, NSW 2140 ISBN 0 7337 0667 3 AS 4418.1 — 1996 2 PREFACE This Standard was prepared by the Standards Australia Committee IT/24 on Supervisory Control and Data Acquisition. The objective of this Standard is to provide manufacturers and users of SCADA systems with a common telecommunications interface and protocol in order to achieve equipment interoperability. The AS 4418 series of Standards has been structured so that Part 1 (this Standard) provides general requirements for SCADA networks and subsequent Parts provide requirements for specific applications. The other published Standard in this series, Part 2: Fire alarm systems, fits the latter criterion. Specific applications Standards may encompass direct-linked networks and dial-in networks using the public switched telephone network. Applications which could form further Parts of this series of Standards could cover areas such as systems for service utilities, transport and security. This is a free 6 page sample. Access the full version online. This series of Standards has been prepared to be consistent with requirements developed by the IEC and published as IEC 870, Telecontrol equipment and systems. Although the IEC 870 series was developed for the electricity industry, the above Australian Standards have been developed as part of a possible series for multi-utility applications. Copyright STANDARDS AUSTRALIA Users of Standards are reminded that copyright subsists in all Standards Australi a publications and software. Except where the Copyri ght Act allows and except where provided for below no publications or soft ware produced by Standards Austr alia may be reproduced, stored in a retri eval system in any form or transmitt ed by any means wit hout prior permission in wri ti ng from Standards Austr alia. Permission may be condit ional on an appropri ate royalty payment. Requests for permission and informati on on commercial soft ware royalt ies should be dir ected to the head off ice of Standards Australi a. Standards Austr alia wil l permit up to 10 percent of the technical content pages of a Standard to be copied for use exclusively in-house by purchasers of the Standard without payment of a royalty or advice to Standards Austr alia. Standards Austr alia will also permit the inclusion of its copyri ght material in computer software programs for no royalty payment provided such programs are used exclusively in-house by the creators of the programs. Care should be taken to ensure that materi al used is fr om the current editi on of the Standard and that it is updated whenever the Standard is amended or revised. The number and date of the Standard should therefore be clearly identif ied. The use of materi al in pri nt form or in computer soft ware programs to be used commercially, with or wit hout payment, or in commercial contr acts is subject to the payment of a royalt y. This policy may be varied by Standards Australi a at any ti me. 3 AS 4418.1 — 1996 CONTENTS Page This is a free 6 page sample. Access the full version online. SECTION 1 SCOPE AND GENERAL 1.1 SCOPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 APPLICATION . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 REFERENCED AND RELATED DOCUMENTS . . . 1.4 DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . ... ........ .. .. .. ... .. .. ... ...... . ... .. ..... 4 4 4 5 SECTION 2 COMMON FUNCTIONAL REQUIREMENTS 2.1 MEDIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2 OPERATING CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3 INTERFACES (ELECTRICAL CHARACTERISTICS) . . . . . . . . . . . . . . . . 2.4 PERFORMANCE REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5 TRANSMISSION PROTOCOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6 SECURITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7 NAMING AND ADDRESSING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 6 6 6 6 6 6 First published as AS 4418.1— 1996. .. .. . ... .. .. .. .. .. .. .. .. AS 4418.1 — 1996 4 STANDARDS AUSTRALIA Australian Standard Supervisory control and data acquisition (SCADA)— Generic telecommunications interface and protocol Part 1: General S E C T I O N 1 S CO P E A N D G E NE R A L 1.1 SCOPE This Standard defines the general functionality and communications protocol of supervisory control and data acquisition (SCADA) networks consistent with the IEC 870 series of International Standards. 1.2 APPLICATION SCADA telecommunications networks shall comply with the requirements of this Standard and a subsequent Part of this series of Standards. 1.3 REFERENCED AND RELATED DOCUMENTS 1.3.1 This is a free 6 page sample. Access the full version online. AS 2777 Referenced documents The following documents are referred to in this Standard: 2777.2 2777.3 Information processing systems— Open reference model Part 2: Security architecture Part 3: Naming and addressing Systems Interconnection — Basic SAA MP 59 Naming and addressing in the Australian OSI environment SAA/SNZ HB55 ANZ GOSIP 3 HB55.6 ANZ Naming and Addressing Guidelines HB68 Information technology —Open Systems Interconnection — Tutorial on naming and addressing IEC 870 Telecontrol equipment and systems 870-1-3 Part 1: General considerations — Section 3: Glossary 870-2-1 Part 2: Operating conditions— Section 1: Power supply and electromagnetic compatibility 870-3 Interfaces (electrical characteristics) 870-4 Performance requirements 870-5-1 Part 5: Transmission protocols — Section 1: Transmission frame formats 870-5-2 Part 5: Transmission protocols — Section 2: Link transmission procedures 870-5-3 Part 5: Transmission protocols— Section 3: General structure of application data 870-5-4 Part 5: Transmission protocols — Section 4: Definition and coding of application information elements 870-5-5 Part 5: Transmission protocols — Section 5: Basic application functions 870-6 Telecontrol protocols compatible with ISO and ITU-T recommendations COPYRIGHT This is a free 6 page sample. Access the full version online. AS 4418.1-1996 Supervisory control and data acquisition (SCADA) - Generic telecommunications interface and protocol General The remainder of this document is available for purchase online at www.saiglobal.com/shop SAI Global also carries a wide range of publications from a wide variety of Standards Publishers: Click on the logos to search the database online.
