COMPONENTS AND REPLACEMENT
PARTS CATALOG
Parts Dept. Phone: 608/592-3212
592-4865
592-3837
Parts Dept. FAX: 608/592-5605
www.alkar.com
Table of Contents
Section I
Table of Contents
ALKAR’s parts department explanation
Contact numbers
Return goods policy
Section 1
Test equipment
Section 2
DDC Standard panel parts
Page 2-1 through 2-3
DDC Modicon panel parts
Page 2-4 through 2-5
DDC Windows panel parts
Page 2-6 through 2-7
Instrument control panel parts
Page 2-8 through 2-24
Section 3
Motor control panel parts
Page 3-1 through 3-5
Section 4
Gas burners and related components
Page 4-1 through 4-8
Section 5
Air handling equipment/steam components
Page 5-1 through 5-8
Section I
I-1
Table of Contents (cont.)
Section 6
Main oven cabinet components
Page 6-1 through 6-3
Section 7
Door hardware and components
Page 7-1 through 7-7
Section 8
Cleaning system components
Page 8-1
Section 9
Smoke/exhaust system components
Page 9-1 through 9-4
Section 10
ALKAR smoke generator parts
Page 10-1 through 10-2
Section 11
Brine chiller & continuous line parts
Page 11-1 through 11-5
Section 12
Trees, trucks, cages and components
Page 12-1 through 12-2
Section I
I-2
Table of Contents (cont.)
Section 13
Safety Labels - ANSI Z535.4 Compliant
Page 13-1 through 13-3
Section 14
Safety Labels – ISO 3584 Compliant
Page 14-1 through 14-4
Section I
I-3
SPARE PARTS SERVICE
For the best performance of your ALKAR equipment it is important to always get the
correct repair or replacement parts. All you need is the ALKAR part number to assure
yourself of getting exactly the part you require. Use this parts catalog as a reference.
If such a listing is not available to you, it is necessary to have the equipment serial number
which is located on the control panel nameplate, or the job number (JT# ----) shown on your
drawings. This is necessary for ordering gas burner repair kits, steam heating coils, air kits,
bearings, etc. ALKAR maintains detailed files on every piece of equipment manufactured.
The serial number or job number will make certain you get the right part to fit the
equipment.
ALKAR has a large inventory of spare parts and therefore, in most cases, the part you need
can be shipped on a next-day basis, right from our stock. In the case where we may not stock
the part, our vendors are only a phone call away. We will arrange for direct shipment from
their plant or warehouse to you. Of course, in case of an emergency we expedite the
shipment the same day via Air Freight or Airport-to-Airport service depending on your
situation and requirements.
CONTACTS, PHONE & FAX NUMBERS
ALKAR Main Office: 608/592-3211
ALKAR Main Office FAX: 608/592-4039
PARTS DEPARTMENT - Extension 285
Phone: 608/592-3212, 608/592-4865, or 608/592-3837
Parts FAX No: 608/592-5605
TO OUR VALUED CUSTOMERS
So that we may better serve you with quicker response time in processing returned goods
for credit or repairs, the following policy has been put into effect: No credit for returns or
shortages will be issued unless prior consent is given either by telephone, mail or FAX.
Shipments received without a Return Authorization Number will be refused and returned to
Customer. Return Authorization Numbers must also be shown on the return label or on the
carton itself.
When the above procedure is followed, we can expedite returns in a timely manner; which
in turn helps keep costs down for both parties. We appreciate your cooperation and
assistance in this manner. If you have any questions, please feel free to contact the ALKAR
Parts Department.
Section I
I-4
RETURN GOODS POLICY
All goods to be returned to ALKAR must be accompanied by a Return Goods Authorization
Form. This form can be obtained through ALKAR Parts Order Department. Return goods
fall into three categories:
1. New Goods Shipped in Error
Restocking or handling charges will not apply to these items shipped in error by
ALKAR. If this error occurs, it should be reported immediately to ALKAR Parts
Order Department. These parts should be returned within 30 days of the order
date.
2. In-Warranty Parts which are Defective
Defective in-warranty parts can be returned for credit, exchange, or no charge
repair and return. ALKAR retains the option of which type of action will be taken
and allowed pertaining to the return goods. Items found not to be defective will be
returned to the customer and no credit issued. Upon returning the defective goods
to ALKAR it is required that an R.G.A. number be stamped on all boxes and a copy
of the return goods authorization form be used as a packing slip for each shipment.
3. Items ordered in Error
New goods in original packaging will fall under this classification. There will be a
25% restocking charge on the net amount on the invoice when this occurs. Goods
are to be returned within 30 days of receipt of authorization.
Acceptance of returned goods will be based on the condition of items at the time of
inspection at ALKAR. Obsolete goods will not be accepted. Unauthorized return goods will
be sent back to the customer “freight collect”. Collect shipments will not be accepted by
ALKAR.
RETURN GOODS PROCEDURE
1. To return merchandise notify the Parts Order Department by either phone, FAX,
or letter requesting a “Return Goods Authorization Form”. The following information must
be provided: Quantity, description, part number and ALKAR invoice number. ALKAR will
then mail or FAX the Return Goods Authorization Form to you.
2. Upon receipt of the form, complete one copy for your files and send one as a
packing slip. The Return Goods Number should appear on the label or on the carton in order
for ALKAR Receiving Department to identify it as a return.
3. All parts must be identifiable by proof of purchase such as an invoice number and
date of purchase. Goods must be returned within 30 days from date of authorization.
4. Ship goods to ALKAR, freight prepaid. Collect shipments will be refused.
Ship to: ALKAR-RapidPak, Inc.
Attn: R.G. Department
817 North Main Street
Lodi, WI 53555
5. Credits, exchanges or repair and returns will be issued after completion of
inspection.
Section I
I-5
TEST EQUIPMENT
• CALIBRATOR
Part No. 25299
4-20 Milli-amp source for calibrating controllers and
recorders.
• CALIBRATOR
Part No. 25297
RTD Simulator for calibrating controllers and recorders.
• CALIBRATOR
Part No. 25298
Type J Thermocouple Simulator for calibrating controllers
and recorders.
• HAND PUMP PRESSURE CALIBRATOR
Part No. 75208
The pressure calibrator is marked for 0-18 psig and is accurate
within 1% of range span. It is a small, hand-held unit for calibrating
pressure instruments. Unit includes carrying case.
• SLACK TUBE MANOMETER
Part No. 75068
8” - 0 - 8” WC manometer will set up to read static pressure, vacuum
and differential pressure. Made of durable plastics so it can be rolled
up when not in use. Complete with hanging magnets and carrying case.
• TURBO METER
Part No. 75261
Electronic wind speed indicator to read air velocities. Small
pocket size, made of durable plastic. Operating temperature
of 32 to 122 F (0-50 C). Runs on 3 AAA batteries with a 3 digit
display and measures knots, feet per minute, meters per second,
miles per hour. Unit includes carrying case.
Section 1
1-1
DDC STANDARD CONTROL PANEL PARTS
• ADVANTECH COMPUTER
Part No. 25262
DDC computer loaded with DDC software, floppy drive
cables, and video card. (Does not include data acquisition card).
• AT-16 RTD INPUT BOARD
Part No. 25226
Used in the DDC to read all the temperature probes
• PENTIUM MOTHERBOARD
PCA-61541
Part No. 25306
• BOARD PC TO I/O MOUNTING RACK
G4AC5OPT022
Part No. 25220
• BOARD A108-P
MLC-AD12-8P
Part No. 25225
• BOARD DT2815
Data Acquisition
Part No. 25197
• CARD SVGA W/1MB
1024 x 768 Advantech PCA-6141 Part No. 25246
• FLOPPY DRIVE 3.5”
Part No. 25245
For use in Alkar DDC and WonderWare controls.
Section 2
2-1
DDC STANDARD CONTROL PANEL PARTS
• KEYPAD
Part No. 31171
For use in Alkar Modicon DDC.
• OUTPUT BOARD, DT 757 Part No. 25224
4 - 20 milliamp output board, cable included.
• PLUG-IN MODULES
Used to control the inputs / outputs for the DDC computer.
For use on Advantech computers, pre-1996.
AC input module - Yellow Part No. 25218
AC output module - Black Part No. 25219
DC ouput module - Red
• HARD DRIVE
25217
25218
Part No. 25217
Part No. 25263
For use in Alkar DDC and WonderWare controls.
• CONNECTOR - BLOCK - #UMS
Part No. 31345
For use in ALKAR DDC control panels
• CONNECTOR - PLUG - #MVST
Part No. 31346
For use in ALKAR DDC control panels
• CALIBRATION RESISTOR
Calibrate DDC Modicon to 230 F. Part No. 70594
Calibrate DDC Modicon to 100 F. Part No. 70595
Section 2
2-2
25219
DDC STANDARD CONTROL PANEL PARTS
• DIGITAL I/O BOARD
Part No. 25216
For use with the plug-in modules to control the
DDC input/output. (Pre-Modicon)
• FAN, BISCUIT
Part No. 31179
For DDC panels.
• FINGER GUARD
Part No. 31180
Use with biscuit fan part no. 31179.
• FAN CORD
Part No. 31181
Use with biscuit fan part no. 31179.
Section 2
2-3
DDC MODICON CONTROL PANEL PARTS
• ADVANTECH COMPUTER
Part No. 25262
DDC computer loaded with DDC software, floppy drive
cables, and video card. (Does not include data acquisition card).
• PENTIUM MOTHERBOARD
PCA-61541
Part No. 25306
• FLOPPY DRIVE 3.5”
Part No. 25245
For use in Alkar DDC and WonderWare controls.
• KEYPAD
Part No. 31171
For use in Alkar Modicon DDC.
• MODICON PLC
Part No. 25268
Modicon micro CPU, programmable logic controller. Applications
include: DDC systems, CIP systems, hydraulic systems, and
Panelmate systems. (Order battery separate). Lithium battery
110xcp-98000.
• MODICON BATTERY
Part No. 25274
• PLUG-IN MODULES
Modicon expansion modules for DDC control panel. When ordering
module, refer to the number printed above wiring terminals.
RTD Input Card 204
Analog Output Card 202
A.C. Output Card 208
Section 2
Part No. 25270
Part No. 25271
Part No. 25272
25270
25271
2-4
25272
DDC MODICON CONTROL PANEL PARTS
• HARD DRIVE
Part No. 25263
For use in Alkar DDC and WonderWare controls.
• MODICON RACK
Part No. 25269
5 slot for DDC DOS versions.
• CONNECTOR - BLOCK - #UMS
Part No. 31345
For use in ALKAR DDC control panels
• CONNECTOR - PLUG - #MVST
Part No. 31346
For use in ALKAR DDC control panels
• CALIBRATION RESISTOR
Calibrate DDC Modicon to 230 F. Part No. 70594
Calibrate DDC Modicon to 100 F. Part No. 70595
Section 2
2-5
DDC WINDOWS CONTROL PANEL PARTS
• ADVANTECH COMPUTER
Part No. 25262
DDC computer loaded with DDC software, floppy drive
cables, and video card. (Does not include data acquisition card).
• NEMATRON COMPUTER
Part No. 25302
For DDC and WonderWare controls
• PENTIUM MOTHERBOARD
PCA-61541
Part No. 25306
• FLOPPY DRIVE 3.5”
Part No. 25245
For use in Alkar DDC and WonderWare controls.
• HARD DRIVE
Part No. 25263
For use in Alkar DDC and WonderWare controls.
Section 2
2-6
DDC WINDOWS CONTROL PANEL PARTS
• MODULES
For PLC based controls.
Discreet input module
Part No. 25295
Output module relay
Part No. 31531
Input module ac/dc
Part No. 31532
Analog module
Part No. 31533
RTD input module
Part No. 31534
• MOUSE
Part No. 25304
For DDC and WonderWare control systems.
• MEMORY MODULE
Part No. 31542
For PLC based controls.
• POWER SUPPLY
Part No. 31539
For PLC based controls.
• PROCESSOR
Part No. 31543
For PLC based controls.
Section 2
2-7
INSTRUMENT CONTROL PANEL PARTS
• COOLER, VORTEX
Part No. 31184
Air cooler for use in DDC Modicon.
• AIR SOLENOID
1/8” NPT, 115 volt,
2 way
3 way
• ALARM HORN
Part No. 65697
Part No. 65698
65697
65698
Part No. 30080
Warning device for: flame failure, duration of processing cycle, set
point changes, time for internal temperature check, etc., 120 VAC,
125 AMP., 50/60 Hz.
• ALARM HORN
Part No. 30975
Warning device for flame failure, duration of processing cycle,
etc., 120 VAC
• BRISTOL CHART RECORDERS
Part No. 25071 (OBSOLETE)
This part is now OBSOLETE and is no longer available.
Part no. 25128 (page 2-12) along with installation materials, junction box,
probes, and filler plate is a complete kit which replaces part no. 25071.
This new replacement kit is alkar part no. 91018. Appropriate drawing will be
included in the kit upon order placement. Field installation and wiring is
approximately 2 -3 days.
Part No. 91018
Section 2
2-8
INSTRUMENT CONTROL PANEL PARTS
BRISTOL REPLACEMENT PEN ARMS
Pen arm, long (Dry Bulb)
Part No. 25066
Pen arm, short (Wet Bulb)
Part No. 25067
BRISTOL REPLACEMENT PEN POINTS
Pen point, long (Dry Bulb)
Part No. 25069
Pen point, short (Wet Bulb)
Part No. 25068
• BRISTOL PEN POINT CLEANING WIRE
Part No. 25074
BRISTOL CHART HOLDING HUB
Part No. 25119
• BRISTOL HANDLE/LATCH
Part No. 25108
Complete door handle and door latch assembly
BRISTOL CHART DRIVE MOTOR
Part No. 25073
Section 2
2-9
INSTRUMENT CONTROL PANEL PARTS
• DRY BULB CONTROLLER Part No. 25095
Three mode (for steam heated ovens only).
• DRY BULB AND WET BULB CONTROLLER
Part No. 25002
Two mode controller which operates on the pneumatic null-balance
principle, controlling the oven or process temperature (Dry or Wet Bulb).
• PNEUMATIC SWITCH
Part No. 30233
For manual control panels. For fresh air and exhaust dampers,
and smoke cook and steam cook.
• SET POINT PROCESS TEMPERATURE GAUGE
3-1/2” dial, 40 - 240 F. range.
Standard accuracy - Part No. 25165
• LENS
Part No. 25166
Replacement 3-1/2” lens flat plastic with O-ring seal.
• SET POINT REGULATOR Part No. 30247
Utilizes the null-balance principle which holds the oven or
steam cooker temperature constant. 0-15PSI, 1/8” NPT.
Section 2
2-10
INSTRUMENT CONTROL PANEL PARTS
• SET POINT TIMER
Time ranges are knob adjustable and have a process pointer. The process
pointer is red and displays the remaining time interval. 102-132 VAC,
60 Hz., output rating: 10 Amps at 120 VAC.
Dial Range
Min. Setting Dial Divisions Repeat Accuracy Part No.
60 min.
2 min.
1 min.
+/- 18 sec.
150 min.
4.5 min.
2 min.
+/- 45 sec.
5 hrs.
9 min.
3 min.
+/- 1.5 min.
10 hrs.
20 min.
10 min.
+/- 3 min.
30084
30085
31033
30087
30084
30085
31033
• SHOWER MISER TIMER (PANEL MOUNTED)
Part No. 30948
Both “On” and “Off” time intervals are individually adjustable
by concentric knobs on the front of the timer. The combination
of “On” and “Off” time is total time cycle of the unit. 102-132 VAC,
50/60 Hz., output rating: 10 Amps at 120 VAC.
• TEMPERATURE RANGE TRANSMITTERS
40 - 240 F. range Standard accuracy - Part No. 25079
40 - 240 F. range. 1/2% accuracy - Part No. 25148
0 - 150 C. range. - Part No. 25231
0 - 100 F. range. - Part No. 25232
Section 2
2-11
30087
INSTRUMENT CONTROL PANEL PARTS
• HONEYWELL CHART RECORDERS
A self-contained, enclosed, temperature recording chart unit.
Electrically operated (115 VAC, 1 ph., 60 Hz.)
24 hour military time print (15 min. intervals) circular chart
Facilities for locking/sealing the chart
Replaces AR100 Series
Includes a self-test feature that checks the operational status
of major functions.
25141
1 Pen (DR4311) - Part No. 25141
2 Pen (DR4312) - Part No. 25128
25128
• HONEYWELL RECORDER/CONTROLLER
Same features as above recorders. Used for internal temperature
control on standard panel, back-up control on microprocessor control
panels. 1 pen - (DR4200 EVI)
Part No. 25171
• HONEYWELL RECORDER/CONTROLLER
Same features as above recorders. Used for back-up control
on microprocessor control panels.
2 pen - (DR4200 EV2)
Part No. 25236
• HONEYWELL CHART DRIVE MOTOR
Part No. 05206
Section 2
2-12
INSTRUMENT CONTROL PANEL PARTS
• PARTLOW REPLACEABLE FELT TIP PENS
Packaged 5 per pack.
Red - Part No. 25157
Green - Part No. 25158
• BRISTOL REPLACEABLE FELT TIP PENS
Packaged 6 per pack.
Red - Part No. 25114
Blue - Part No. 25115
• HONEYWELL REPLACEABLE FELT TIP PENS
Packaged 6 per pack.
Purple (long) - Part No. 25135
Red (short) - Part No. 25114
• PARTLOW REPLACEMENT PEN ARMS
Special order. Allow 4 weeks delivery. Long arm or short arm.
Section 2
2-13
INSTRUMENT CONTROL PANEL PARTS
• CIRCULAR CHART RECORDER INK
For use with Bristol Recorder, 1 bottle 2.5 ounces.
Red Blue -
Part No. 25082
Part No. 25051
• CIRCULAR RECORDER CHARTS
Packed 100 charts per box. All charts 24 hour.
Honeywell: Range 0-150 C.
Honeywell: Range 0-200 F.
Honeywell: Range 0-200 F.
Honeywell: Range 50-250 F.
Partlow: Range 0-350 F.
Partlow: Range 50-250 F.
Partlow: Range 30-230 F.
Bristol: Range 40-240 F.
Bristol: Range 60-180 F.
Part No. 25291
Part No. 25120 (11.5” dia.)
Part No. 25139 (10.5” dia.)
Part No. 25136
Part No. 25031
Part No. 25032
Part No. 25156
Part No. 25075
Part No. 25162
Part No. 25155
Bristol: Range 0-400 F.
Note: For Drying Room charts, please specify chart number
• DELAY START TIMER
25291
25120
25139
25136
25031
25032
25156
25075
25162
25155
Part No. 30082
Used for special application only. Delay start of Wet Bulb
set point or preset time (in seconds) allowing Dry Bulb to reach
set point first. 115 VAC, 10 AMP rated.
• PANELMATE SERIES 1000
Part No. 25277
The Panelmate unit is a video control panel that will interface
with a single PLC or multiple PLCs on a network. The unit is
a single piece construction with front touchpanel and controls.
Section 2
2-14
INSTRUMENT CONTROL PANEL PARTS
66306
65100
66305
65093
66352
66430
66353
• DESICCANT CRYSTALS Part No. 65094
Replacement desiccant crystals for Desiccant Dehydrator Dryer
Unit. Two bags are required.
• DESICCANT DEHYDRATOR DRYER UNIT
Part No. 65093
A manual compressed air dryer unit, that indicates replacement of
regeneration of desiccant crystals by changing from blue to pink
within the transparent bowl window. Dryer unit includes two (2) bags
of desiccant. Additional bags of desiccant may be ordered.
Dessicant Bowl Specifications
Capacity: 1.74 pounds
Temperature rating: up to 125 F.
Pressure rating: up to 150 PSIG
Dryer Specifications
Dries up to 4400 standard cubic feet at 70 F. (saturated inlet air
temperature) at 100 PSIG
Section 2
2-15
INSTRUMENT CONTROL PANEL PARTS
• MICROALESCER WITH FILTER, TYPE C
Baffling system for removing liquids (water & oil) and dirt
particles mechanically. Quick-disconnect clamp ring on metal
bowl. Metal bowl features level gauge and 11 oz. Capacity.
Comes with Type “C” (coarse) or Type “D” (fine) filters.
With Type “C” filter
With Type “D” filter
Part No. 65100
Part No. 66305
65100
66305
• MICROALESCER REPLACEMENT FILTER, TYPE C
Part No. 66353
Replacement filter only. (Coarse)
• MICROALESCER REPLACEMENT FILTER, TYPE D
Part No. 66430
Replacement filter only. (Fine) New type D.
• MICROALESCER REPLACEMENT FILTER, TYPE D
Part No. 66352
Replacement filter only. (Fine) Old type D.
• AIR SUPPLY REGULATOR WITH GAUGE
Part No. 66306
Maintains high air flow with steady pressure control with minimal
pressure drop. Fluctuations in secondary pressures are minimal,
regardless of fluctuations in primary pressures. Secondary pressure
range is 5 to 125 PSIG. NPT size: 1/4”
Section 2
2-16
INSTRUMENT CONTROL PANEL PARTS
• DOOR INTERLOCK
Part No. 30863
Instrument panel interlock switch. Used for all instrument
control panels.
• ELECTRICAL SWITCH
With contact block.
2 position - Part No. 30894
3 position - Part No. 30897
• CONTACT BLOCK
Contact blocks for electrical and stop/start push button
switches. 10 AMP., 600 Volt.
Normally open - Part No. 30550
Normally closed - Part No. 30551
30550
30551
• INDICATING LIGHT SOCKET ASSEMBLY
Complete with twist type socket and indicator bulb.
4 Watt, 120 VAC.
Red lens - Part No. 30893
Green lens - Part No. 30895
INDICATING BULB
Replacement in control panel.
Bayonet socket - 4 watt, 120 VAC Part No. 30871
Screw socket - 6 watt, 120 VAC Part No. 30252
30871
30252
• PILOT LIGHT LENS
Red - Part No. 30255
Green - Part No. 30257
• SWITCH
Part No. 30892
ASD211N
Section 2
2-17
INSTRUMENT CONTROL PANEL PARTS
• INTERNAL CONTROL REGULATOR
Part No. 30898
0-30 psi. 1/4” NPT.
• INTERNAL TEMPERATURE CONTROL
Part No. 25237
DC230B-EE-00-10. Used on Standard and Jumo control
panels for wet and dry bulb controllers.
• INTERNAL TEMPERATURE CONTROL
Part No. 25238
DC230L-E0-00-10. Used for internal temperature alarm or limit.
• SHOWER MISER TIMER Part No. 31501
Intermittently turns the cold shower system on or off at timed
intervals to conserve water during the shower cycle.
• SHOWER MISER TIMER BASE
Part No. 31502
For use with shower miser timer part no. 31501
• SHOWER MISER LATCH KIT
Part No. 31503
Latch kit only.
Section 2
2-18
INSTRUMENT CONTROL PANEL PARTS
• JUNCTION BOX ENCLOSURE
6” x 6”, 1 pen and 2 pen
Part No. 31693 (replaces 45052)
10” x 12”
Part No. 31756 (replaces 45072)
8” x 10”, 3 pen and 4 pen Part No. 31755 (replaces 45074)
• JUNCTION BOX INTERNAL PANEL
6” x 6”, 1 pen and 2 pen
Part No. 45053
10” X 12”
Part No. 45073
8” x 10”, 3 pen and 4 pen Part No. 45075
• JUNCTION BOX THERMOCOUPLE TYPE J WIRE
Part No. 30935
A special wire (Iron-Constantan).
Available for 1 pen, 2 pen, 3 pen, and 4 pen.
• CORROSION INHIBITOR Part No. 30910
Used for control of corrosion in instrumentation controls.
• RELAY
Part No. 30939
RY4S-U-AC 120V IDEC
• SOCKET
Part No. 30940
Relay socket, 4PDT
• LATCH
Part No. 75333
E3-10-505-50 large knob style
Section 2
2-19
INSTRUMENT CONTROL PANEL PARTS
• NAMEPLATE
Door Open
Door Closed
Power ON
Power OFF ON
Backup ON OFF
Program Lock ON OFF
Part No. 31110
Part No. 31111
Part No. 31222
Part No. 31227
Part No. 31248
Part No. 31249
• POTENTIOMETER
P1004-13, 5 MEG OHMS
SSAC Inc. VTP5N
• RESISTOR
Part No. 31104
Part No. 31213
Part No. 31125
Metal Oxide Varsitor
• RHEOSTAT
Part No. 31289
100 OHM 25 Watt
• SETPOINT RETROFIT
Part No. 31289
Assembly
• SIGNAL CONDITIONER Part No. 30940
API-4003G-I, 4-20 MA
• SOCKET
Part No. 30940
Relay socket, 4PDT
• SWITCH, KEY LOCK
Part No. 31247
ASD2K10N IDEC
• TIMER
Part No. 31103
Recycle ESDR453A3
Section 2
2-20
INSTRUMENT CONTROL PANEL PARTS
• PLUG-IN TIME DELAY RELAY
Part No. 30881
10 second time delay start timer (must also order timer base #31653)
• PLUG-IN TIME DELAY RELAY BASE
Part No. 31653
For use with above time delay relay #30881
• PRESSURE INDICATING GAUGE
2” Dial.
0-30 psi - Part No. 25003
0-60 psi - Part No. 25118
25003
• PRESSURE GAUGE
25118
Part No. 25259
Liquid filled, 3-15 psi control output. For use in DDC, PLC,
and WonderWare controls.
• PUSH BUTTON
Part No. 30890
ABD110N-B
• PUSH BUTTON
Part No. 30891
Red
• RELAY
Part No. 30225
8 pin, plug-in style, D.P.D.T. contact arrangement. 115 VAC,
10 AMPS. Mechanical tests indicate a life expectancy of more
than 10 million operations.
• RELAY BASE
Part No. 30573
8 pin, for use with relay part no. 30225. 115 VAC, 10 AMP.
Section 2
2-21
INSTRUMENT CONTROL PANEL PARTS
• RTD DRY BULB AND WET BULB PROBE
Single element sensor Part No. 25201
Measures Dry Bulb and Wet Bulb temperatures and sends signal
back to the microprocessor.
• RTD DRY BULB AND WET BULB PROBE
Monel 400 Sheath Part No. 25267
Measures Dry Bulb and Wet Bulb temperatures and sends signal
back to the microprocessor.
• RTD DRY BULB AND WET BULB PROBE
Dual Element Sensor Part No. 25255
Measures Dry Bulb and Wet Bulb temperatures and sends signal
back to the microprocessor.
• DRY BULB AND WET BULB SENSOR
20 ft
Part No. 25127
RTD Dry Bulb and Wet Bulb Sensor.
• INTERNAL TEMPERATURE PROBE
Probe to monitor internal temperature of product.
Type J, 25 foot
Type J, 12 foot
Part No. 25121
Part No. 25142
25121
25142
INTERNAL TEMPERATURE PROBE
25 foot
Part No. 25163
32 foot
Part No. 25288
RTD probe to monitor internal temperature of product.
• INTERNAL TEMPERATURE PROBE
25 ft
Part No. 25293
To measure internal temperature of hot dogs.
Section 2
2-22
INSTRUMENT CONTROL PANEL PARTS
• TERMINAL BLOCK
Part No. 31017 (OBSOLETE)
Replaced by terminal block #31609
• TERMINAL CONNECTOR
TLCO - 20 Constantan
Part No. 31016 (OBSOLETE)
TLIR - 20 Iron
Part No. 31015 (OBSOLETE)
31015
31016
Replaced by terminal block #31609
• TERMINAL BLOCK
Part No. 31609
Motor control panel component, gas heated ovens only.
• TIME DELAY RELAY
Part No. 30782
N.C. relay. (MCR120A1X1Q-2). A solid state printed circuit board
with mechanical relay used to complete circuit until air flow switch is
energized. 115 VAC, 10 AMP rated. For use with gas fired equipment
only with Barber Coleman Flame Safe Guard Control.
• TRANSDUCER
Part No. 25307
This unit is supplied by a 4 to 20 milliamp signal and converts
it to a 3 to 15 PSIG output.
Section 2
2-23
INSTRUMENT CONTROL PANEL PARTS
• TYPE J THERMOCOUPLE
Part No. 25151
High temperature limit located in the return air stream. Same
for 0-250 or 0-400.
• TYPE J THERMOCOUPLE WIRE
Part No. 30935
A special wire (iron and constantan). Specify length.
• WATERPROOF CORD CONNECTOR , 1/2” CONDUIT
Part No. 30978
• WET BULB SOCKS
Made from 100% cotton fabric to assure proper evaporation
for correct wet bulb reading. Socks are sewn to properly fit wet
bulb diameter giving you an accurate wet bulb control.
6” x 6” For pneumatic control panels (programmable-standard,
also old style two truck ovens) 3/4” diameter sensor.
Part No. 50041
3” x 5-1/2” For microprocessor control panels on small ovens.
Part No. 50040
5-1/2” x 5-1/2” For microprocessor control panels on larger ovens.
Part No. 50044
Section 2
2-24
MOTOR CONTROL PANEL PARTS
• BIC - 10” HIGH TEMPERATURE LIMIT
Part No. 30613
Used in supply air stream. (Used prior to 1974). Temperature
range: 100 - 600 F. with manual reset.
• CIRCUIT BREAKERS
Used to protect control voltage circuit and oven light.
4.5 Amp, 115 Volt
5.0 Amp, 115 Volt
Part No. 31101
Part No. 30667
31101
30667
• CONTROL CIRCUIT
(Secondary Voltage Transformer), Primary voltage 230/460,
secondary voltage 115.
VA500 Part No. 30090
30090
30091
VA1000 Part No. 30091
Primary voltage 208, secondary voltage 115
30737
VA500 Part No. 30737
• FLAME SAFEGUARD CHASSIS
Provides automatic ignition and flame safeguard control
for gas burners.
Part No. 30887 (flame rod type) is obsolete
Part No. 31034 (UV scanner type) is obsolete.
New Replacement Parts:
31303
31304
31305
Chassis - Part No. 31303
Programmable module - Part No. 31304
Amplifier, flame rod module - Part No. 31305
Chassis base (61-3060 Fireye) - Part No. 30888
UV Amplifier module - Part No. 31306
30888
31307
31306
Programmable module - Part No. 31307
Section 3
3-1
MOTOR CONTROL PANEL PARTS
• HIGH TEMPERATURE LIMIT CONTROL
Part No. 31645
Replaces control switch #31324
• HIGH TEMPERATURE LIMIT CONTROL
Part No. 25238
Replaces part no. 25253
Limit control in return air stream to protect product from high
temperature (dry bulb only) malfunction. Adjustable from 0-250 F.
or 0-400 F. (Replaces part number 25150)
• HIGH TEMPERATURE LIMIT SWITCH
Used in supply air discharge. Normally set between 350 F. and 550 F
depending on location of limit switch, size of burner, CFM of main
blower (fan). The control is located on the rotating damper section.
31645
Original part 30786 is obsolete. Replacement parts are as follows:
30896
31326
Limit switch - Part No. 31645
Push button - Part No. 30896
Tag - Part No. 31326
Terminal block - Part No. 31609
31608
31609
Terminal block end cover - Part No. 31608
Type J wire - Part No. 30935
Thermocouple- Part No. 25151
25151
30935
Section 3
3-2
MOTOR CONTROL PANEL PARTS
• IGNITION TIMER (PILOT CUT-OFF TIMER)
Part No. 30082
This timer is set for maximum of 15 seconds. If pilot light is not
proven before this time, system will return to purge cycle (3 minutes).
The reset timer is synchronous driven. This provides an accurate adjustable
time delay between the actuation of the control circuit and the operation of
the load switches. 120V, 50/60 Hz.
• IGNITION TRANSFORMER
Part No. 30119
Primary voltage: 115V, secondary voltage: 600V. Used to ignite
pilot flame of main burner.
• NAMEPLATE
Part No. 31327
Reset Hi Temp Limit, return air
• NAMEPLATE
Part No. 31344
Hi Temp Limit Alarm
• N.O. RELAY
Part No. 30774
MCR120A1X10-1. Used for momentary (10 sec.) delay to prevent
lock out of air flow and combustion air circuit. (Used prior to 1979).
• TIME DELAY RELAY
Part No. 30082
Used for momentary (10 sec.) delay time to prevent lock out of
air flow and combustion air circuit. 120VAC., 10 Amp rated.
• PURGE TIMER
Part No. 30083
This timer is set for minimum 3 minutes for required ventilation of fuel
accumulation during a shutdown period, before lighting or relighting of
oven. This provides an accurate adjustable time delay between the
actuation of control circuit and the operation of the load switches.
120V, 50/60 Hz. Note: this timer replaces old timer No. HD32A622.
Section 3
3-3
MOTOR CONTROL PANEL PARTS
• RELAY
Part No. 30225
AAE-A201 or RR2P-U.
8 pin, plug-in style, D.P.D.T. Contact arrangement. 115VAC, 10 AMPS.
Mechanical test indicated a life expectancy of more than 10 million operations.
• RELAY BASE
Part No. 30573
SR2P-06.
8 pin, for use with above relay #30225. 115VAC, 10 AMP rated.
• NEON LIGHT
Part No. 30250
Replacement neon light for sequence monitor. 125V., .5 watt.
• TERMINAL BLOCK
Part No. 31609
Motor control panel component, gas heated ovens only.
• TERMINAL BLOCK END COVER
Part No. 31608
Motor control panel component, gas heated ovens only.
• TYPE J THERMOCOUPLE
Part No. 25151
High temperature limit located in the return air stream. Same for
0 - 250 or 0 - 400 F.
• LATCH
Part No. 75335
E3-10-505-50 large knob style
• CONTACTOR
Part No. 30976
MDI 235NO-120A
Section 3
3-4
MOTOR CONTROL PANEL PARTS
• CONTACTOR
Part No. 30844
MDI #360N0-12A 60 amp 3 pole
• CONTACTOR
Part No. 30885
CFC3-708 Dura-kool
• RELAY
Part No. 30847
AE 504-0-0-2
• RELAY
Part No. 30939
RY4S-U-AC 120V IDEC
• RELAY
Part No. 31137
Midget Power Latching RH2LB120VAC
• RELAY
Part No. 31143
IDEC RH1B-U 120VAC
• RELAY
Part No. 31476
Overload relay
• SOCKET
Part No. 30940
Relay socket, 4PDT
• SOCKET
Part No. 31138
Relay socket
• SOCKET
Part No. 31144
Relay socket
• TRANSFORMER
Part No. 31163
Heavy duty, #HS1F1.5AS 230/460
Section 3
3-5
GAS BURNERS AND COMPONENTS
• MAXON MODEL 400 GAS BURNER
The model 400 includes a combustion air blower with non-loading
paddle-wheel impeller, plus an air and gas proportioning system. Simple
adjustment requires only the setting of gas supply pressure, using a manometer
test connection provided on the burner.
OVENPAK 1 (Ovens prior to July 1993)
Model
HP
405
408
415
425
435
445
456M
MBTU/HR @-5” to -0.5”wc
1/3
1/3
1/3
3/4
3/4
1
1-1/2
550
880
1650
2750
3850
5175
6400
Part No.
2.8”wc
3.4”wc
1.7”wc
2.7”wc
2.2”wc
3.4”wc
3.6”wc
40079
40070
40072
40071
40120
40124
40125
OVENPAK 2 (Ovens after to July 1993)
Model
HP
405
408
415
425
1/3
1/3
1/3
3/4
MBTU/HR @-5” to -0.5”wc
550
880
1650
2750
Part No.
2.8”wc
3.4”wc
1.7”wc
2.7”wc
40141
40142
40143
40144
• BURNER EXTENSION SLEEVE
Discharge sleeves are made of stainless steel and are used for
combustion chambers. For Ovenpak 1 only
For Models 405 & 408
For Model 415
For Models 425 & 435
Section 4
Part No. 70017
Part No. 70016
Part No. 70019
4-1
GAS BURNERS AND COMPONENTS
• BURNER GASKET SETS
Provides additional sealing to reduce the likelihood of heat damage to
burner and piping components. (Sold in sets of 2 for Ovenpak 1 only).
For Models 405 & 408
For Model 415
For Models 425 & 435
Part No. 70488
Part No. 70489
Part No. 70490
• CONE - AIR MIXING
Air mixing cone for gas burner.
For Model 405 ovenpak 1
For Model 408 ovenpak 1 & 2
For Model 415 ovenpak 1 & 2
For Model 425 ovenpak 1 & 2
• CRANK ARM
Part No. 40145
Part No. 40128
Part No. 40127
Part No. 40171
Part No. 05114
• GUIDE TUBE
For Maxon 415 ovenpak 1 Part No. 40160
For Maxon 415 ovenpak 2 Part No. 40163
For Maxon 425 ovenpak 1 Part No. 40166
For Maxon 425 ovenpak 2 Part No. 40170
Section 4
4-2
GAS BURNERS AND COMPONENTS
• IMPELLER
For Maxon 408 & 415 ovenpak 1 Part No. 40173
For Maxon 415 ovenpak 2
For Maxon 425 ovenpak 1
For Maxon 425 ovenpak 2
Part No. 40162
Part No. 40165
Part No. 40169
• INTERNAL LINKAGE KIT
Contains: linkage, shaft, gas and air butterflies.
For Maxon 405, 408, 415 ovenpak 1
For Maxon 425 and 435 ovenpak 1
For Maxon 405, 408, 415 ovenpak 2
For Maxon 425 and 435 ovenpak 2
Part No. 40121
Part No. 40122
Part No. 40139
Part No. 40140
• NOZZLE
Natural gas nozzle.
For Maxon 405 ovenpak 1
For Maxon 415 ovenpak 1
For Maxon 415 ovenpak 2
For Maxon 425 ovenpak 1
For Maxon 425 ovenpak 2
Section 4
Part No. 40146
Part No. 40129
Part No. 40164
Part No. 40168
Part No. 40172
4-3
GAS BURNERS AND COMPONENTS
• AIR ACTUATOR MOTOR - 4”
Part No. 05142
Operating range: 3-15 PSI. Used to modulate gas burner flame.
Proportional pneumatic actuator has 8 sq. inch of effective area.
• MOUNTING BRACKET - ACTUATOR / BURNER
For use in mounting actuator on burner
For models 405, 408, and 415
For models 425 and 435
• CLEVIS KIT
Part No. 70296
Part No. 70297
Part No. 05143
For gas burner/actuator motor.
• DIAPHRAGM, 4”
Part No. 05062
For 4” Air Motor
• FLAME SAFEGUARD CHASSIS
Provides automatic ignition and flame safeguard control
for gas burners.
Part No. 30887 (flame rod type) is obsolete
Part No. 31034 (UV scanner type) is obsolete.
New Replacement Parts:
31303
31304
31305
Chassis - Part No. 31303
Programmable module - Part No. 31304
Amplifier, flame rod module - Part No. 31305
Chassis base (61-3060 Fireye) - Part No. 30888
UV Amplifier module - Part No. 31306
Programmable module - Part No. 31307
Section 4
30888
31307
31306
4-4
GAS BURNERS AND COMPONENTS
• FLAME ROD
For Models 405, 408, 415, 425, 435 Part No. 40097
For Models 445 and 456M Part No. 40126
• CONNECTOR - 90 SPARK PLUG INSULATOR
Part No. 30557
To connect spark ignitor or flame rod.
• COAXIAL CABLE
Part No. 30864
Durable, insulated coaxial cable for flame rods.
• GAS VALVE ACTUATOR HEAD
Part No. 66169
Type V4055D. For gas supply control to the main burner. Opening
time: 13 sec., closing time: 1 sec. For use with V5055A valve body.
• GAS VALVE BODY
Type V5055A. For use with V4055D actuator head.
Part No. 65079
1-1/4” Part No. 65081
1-1/2” Part No. 65082
2”
Part No. 65086
1”
• DIAPHRAGM, 3”
Part No. 05065
For 3” Powers Air Motor
• DOOR INTERLOCK
Part No. 31483
Requires a 3 minute purge cycle prior to pilot ignition.
Section 4
4-5
GAS BURNERS AND COMPONENTS
• MAIN GAS REGULATOR MODEL 122
The model 122 features fast response speed, yet is stable in operation.
Soft seats assure positive, tight shut-off. Orifices are replaceable. Springs
are color coded. Valve sizes range from 1” to 2” N.P.T. To order
specify information from existing regulator.
• HIGH-LOW GAS PRESSURE SWITCH
Part No. 30005
Type RHLGP (old style), has a 3/8” N.P.T. high pressure inlet and a
1/8” N.P.T. low pressure inlet. Adjustable on high gas from 5” to 28”
of water column (wc), adjustable on low gas from 1” to 6” wc.
Pressure switch features manual reset. Maximum surge limit: 10 PSIG.
• HIGH-LOW PRESSURE SWITCH
High gas pressure switch
Part No. 30933
Low gas pressure switch
Part No. 30934
• PILOT GAS REGULATOR - 3/8”
Part No. 25159
The 043 is a general purpose service regulator for use with natural gas,
propane or butane. Fast response speed, yet stable in operation.
• PILOT SOLENOID VALVE
Part No. 66043
2-way, normally closed, direct-lift solenoid valve. 115V.
• INTERLOCK SWITCH
Part No. 30591
For burner low fire start and for fresh air and exhaust dampers
Section 4
4-6
GAS BURNERS AND COMPONENTS
• CAM
Part No. 70061
For burner low fire start interlock
• CAM
Part No. 70327
For fresh air and exhaust dampers
• PRESSURE SWITCH
Part No. 30012
Pressure activated to effect a safety shutdown or prevent burner start-up
in the event the main blower is not running while purging the oven.
• PRESSURE SWITCH, COMBUSTION AIR
Part No. 30012
Pressure activated to effect a safety shutdown or prevent burner start-up
in the event the combustion air in the burner is below burner manufacturer
recommendations.
• REPLACEMENT DIAPHRAGM
Part No. 05125
For Powers air actuator motor (old style)
Section 4
4-7
GAS BURNERS AND COMPONENTS
• REPLACEMENT DIAPHRAGM
Part No. 05051
For Honeywell air actuator motor.
• SPARK IGNITOR
Part 30632
Fits all size gas burners.
• IGNITOR CABLE
Part No. 30265
Spark conduction wire for ignitor.
• ULTRAVIOLET SCANNER
Part No. 31081
Used in place of flame rod on UVM type combustion safeguard chassis.
• VALVE, SOLENOID
2-WAY, normally open, direct-lift solenoid valve. 115V.
For 3/4” NPT
For 1” NPT
Part No. 65003
Part No. 66337
65003
Section 4
66337
4-8
AIR HANDLING EQUIPMENT/STEAM COMPONENTS
• MAIN FAN AIR KIT PARTS
All components are of mild steel unless designated by S/S (stainless steel).
Kit Size Wheel Part No. Housing Part No. Shaft Part No. Size
X12A31-1/D
40050
40034
40093
1-15/16” x 42”
70291 S/S
70292 S/S
X15A35-1/D
40051
70289 S/S
40035
70290 S/S
40094
2-3/16” x 47”
X18A35-1/D
40052
70273 S/S
40036
70272 S/S
40095
40153
2-3/16” x 57”
2-3/16” x 59” (Inline CPS)
X22A43-1/D
40053
70271 S/S
40037
70270 S/S
40096
40154
2-11/16” x 65”
2-11/16” x 67” (Inline CPS)
X24A55-1/D
40054
70286 S/S
40038
70287 S/S
40101
3-7/16” x 75”
T.D. 2-11/16”
X27A63-1/D
40055
70303 S/S
40039
70304 S/S
40102
3-15/16” x 82”
T.D. 2-11/16”
3-15/16” x 83”
T.D. 2-11/16”
40155
X30A63-1/D
40056
70314 S/S
40040
70315 S/S
40149
3-15/16” x 92”
T.D. 2-11/16”
X33A71-1/D
40057
70311 S/S
------70312 S/S
40147
4-7/16” x 98”
T.D. 2-11/16”
Section 5
5-1
AIR HANDLING EQUIPMENT/STEAM COMPONENTS
• PILLOW BLOCK BEARINGS
Available in fixed or expansion type.
Size
1-15/16”
1-15/16”
2-3/16”
2-3/16”
2-11/16”
2-11/16”
Type
Fixed
Expansion
Fixed
Expansion
Fixed
Expansion
Bearing No.
S-3080-M-31
S-3081-M-31
S-3080-M-35
S-3081-M-35
S-3080-M-43
S-3081-M-43
2-11/16”
Fixed
Dodge (for 3000 & 3300 air kits)
Part No.
35286
35287
35288
35289
35290
35291
35522
• SHAFT SEALS
Rubber seals to provide durable bearing protection. Available in sets of 2.
Seal no. V-50-S
1-15/16”
Seal no. V-55-S
2-3/16”
Seal no. V-70-S
2-11/16”
Part No. 15081
Part No. 15080
Part No. 15079
• ACCESS DOOR CLAMPS
Part No. 75229
Used for securing blower cabinet access door. Stainless steel only.
• AIR ACTUATOR MOTOR - 4”
Part No. 05061
• AIR ACTUATOR - STRAIGHT CONNECTOR
Part No. 05003
Replacement component.
Section 5
5-2
AIR HANDLING EQUIPMENT/STEAM COMPONENTS
• ACTUATOR
Electrical actuators for small ovens
Proportional 120 / 60
Two position
Part No. 05115
Part No. 05133
• MOTOR
Electric motors for small ovens
Century, 1HP, P-126 Frame, 143JP Part No. 05115
• COUPLER
Flex, ½” x ½”, #11732
Part No. 35269
• BUSHING
H x 7/8”
Part No. 35318
• BLADE, FAN
4 #18, cast aluminum Prop 7/8”
Hartzell P1794, 7/8” bore
Section 5
Part No. 40117
Part No. 40131
5-3
AIR HANDLING EQUIPMENT/STEAM COMPONENTS
• AIR ACTUATOR - BLADE LINKAGE KIT
Part No. 35322
Replacement component linkage kit.
• AIR ACTUATOR - CRANK ARM
Part No. 05001
• AIR ACTUATOR - DIAPHRAM
Part No. 05062
Replacement component.
• AIR ACTUATOR - INTERLOCK SWITCH
Part No. 30591
Replacement component. Prove fresh air intake and exhaust dampers open.
• AIR ACTUATOR - LINKAGE ROD
Part No. 70282
Replacement component.
• AIR ACTUATOR - MICRO SWITCH CAM
Part No. 70327
Replacement component.
• AIR ACTUATOR - SWIVEL CONNECTOR
Part No. 05055
Replacement component.
Section 5
5-4
AIR HANDLING EQUIPMENT/STEAM COMPONENTS
• GEAR REDUCER
For rotating damper section. Reducer: single output shaft projection,
1200:1 ratio is flanged, 2000:1 ratio is direct drive
1200:1 Part No. 35315
2000:1 Part No. 35330
• MOTOR (FOR GEAR REDUCER)
Part No. 05144
For rotating damper section. 1750 RPM, 1/3 HP, Voltage: 208-230/460
3 phase, 60 Hz.
• BEARING / FLANGE
Part No. 35101
1” flange bearing for damper blades.
• BEARING SEAL
Part No. 70389
Damper blade bearing seal - 1”
• CHAIN TENSIONER
Part No. 35273
For providing chain tension on rotating damper blades.
• CHAIN TENSIONER IDLER SHAFT
Part No. 35285
Fits with above chain tensioner, part number 35273
• ROLLER CHAIN
Part No. 35121
#35 mild steel roller chain sold in 1 foot increments.
Section 5
5-5
AIR HANDLING EQUIPMENT/STEAM COMPONENTS
• ROLLER CHAIN LINKS
Part No. 35118
#35 mild steel full link.
• ROLLER CHAIN LINKS
Part No. 35119
#35 mild steel half link.
• SPROCKET
Part No. 35123
Used with #35 roller chain.
• BUSHING - MOTOR / REDUCER
Part No. 35107
Soft steel bushing for sprocket #35123. To fit output shaft of
gear reducer.
• SPROCKET - IDLER
Part No. 35274
Idler sprocket used with #35 roller chain.
• STEAM TRAP
Part No. 66251
Nicholson B-33, 1/2”
• STEAM TRAP
Part No. 65050
Armstrong 880, 3/4” for use with Separator part no. 65065
• HUMIDIFIER SEPARATOR - 1-1/4”
Part No. 65065
Used to separate condensate before discharging to air stream.
• STEAM HEATING COILS (NOTE: Specify oven serial no. when ordering coils)
All steam coils are custom made to size. Steam coil material include stainless steel casing,
tube and flanges with copper fins.
Section 5
5-6
AIR HANDLING EQUIPMENT/STEAM COMPONENTS
• STEAM VALVE ACTUATOR REPAIR KIT
Part No. 40152
Actuator repair kit for Baumann valve
• STEAM VALVE ACTUATOR REPAIR KIT
Part No. 66368
Actuator repair kit for type 513R-GS.
Includes
Main diaphragm (nitrile & dacron)(1N4478-06992)
O-ring (nitrile)
(1V1156-06992)
O-ring (nitrile)
(1V1157-06992)
Gasket
(1N4486-04022)
Dust seal (neoprene) (1V1170-06992
• STEAM VALVE ACTUATOR REPAIR KIT
Actuator repair kit for type 667-GS
Includes:
3 - O-rings and 1 gasket. Diaphrams not included.
R667X000302, Size 30
R667X000402, Size 34
Part No. 66354
Part No. 66412
• STEAM VALVE DIAPHRAMS
For type 667-GS Fisher valve
2E800002202, Size 30
2E669902202, Size 34
Section 5
Part No. 66413
Part No. 66414
5-7
AIR HANDLING EQUIPMENT/STEAM COMPONENTS
• LARGE DIAPHRAGM FOR 513R-GS VALVE
Part No. 65657
• SMALL DUST SEAL FOR 513R-GS VALVE
Part No. 65658
• SARCO STEAM VALVES
To order the correct steam valve, please supply the following information:
- Line size of valve
- Plant steam pressure at valve
- Operating air pressure of valve, 3-15 psig or 9-15 psig
Section 5
5-8
MAIN OVEN CABINET COMPONENTS
• COLD SHOWER SOLENOID VALVE
Brass body, 115 VAC. Available in the following sizes:
Part No. 66338
Part No. 66339
Part No. 65007
1-1/4”
1-1/2”
2”
• COLD SHOWER SPRAY NOZZLES
1/4” HH14W, 1.9 GPM at 20 psig water pressure.
Brass
Stainless Steel
Part No. 65650
Part No. 65990
• NOZZLE INSERT ADAPTER
Part No. 65664
Used prior to 1983 on S/S tubing. 1/4” NPT, #568 Delrin. Inserts are
pressed into drilled hole in tubing to accept threaded nozzles.
• FLOOR DRAIN COMPONENTS
Floor drain support (S/S)
Part No. 45017
12” cast iron basket
Part No. 65129
12” cast iron grate
Part No. 65128
• MOUNTING BRACKET FOR FLOW METER
Part No.70308
For use in surface mounting the flow meter to the oven.
• PSYCHROMETER PAN FLOW METER
Part No. 25109
Used to meter water flow to the psychrometer pan reservoir. Has
a micrometer adjustment to provide a flow rate from 0 - 50 cc
per minute.
Section 6
6-1
MAIN OVEN CABINET COMPONENTS
• OVEN LIGHT ASSEMBLY
Available in three styles. To provide lighting inside oven
for operators.
APPLETON FIXTURE:
Fixture base Part No. 30867
Adapter Part No. 30866
Globe, glass Part No. 30865
Guard
Part No. 30879
CROUSE HINDS FIXTURE:
Base Part No. 31480
Globe Part No. 31482
Guard Part No. 31481
HUBBELL FIXTURE:
Base Part No. 31409
Adapter - straight Part No. 31410
Adapter - 90 degree Part No. 31408
Globe, polycarbonate Part No. 31411
Guard Part No. 31412
• PSYCHROMETER PAN
Used for support of the wet and dry bulb transmitters. Pan
serves as the water reservoir for the wet bulb sock.
Standard Part No. 45013
Microprocessor Part No. 45125
• SUPPLY DUCT CONES
45013
45125
Part No. 70147
2” replacement cones for supply ducts. Stainless steel rolled cones.
Section 6
6-2
MAIN OVEN CABINET COMPONENTS
• VALVE, SOLENOID
Part No. 65011
8220G21, 1/2”
Part No. 66249
8262G22, 1/4”
Part No. 66285
8222G74, 3/8”
Part No. 66286
8210G9, 3/4”
Part No. 66288
8263G306, 3/8” Part No. 66441
8220G25, 1”
Part No. 66462
8314G23
Part No. 66677
8210G2, 1/2”
• ATOMIZING NOZZLE
Brass, 1/4”, size 1.5
Brass, 1/4”, size 6
Section 6
Part No. 66287
Part No. 66475
6-3
OVEN DOOR HARDWARE - COMPLETE KIT
See Note*
Optional
3 Point Latching
4 Point Latching
5 Point Latching
DISCOUNTED PRICE IF COMPLETE KIT PURCHASED
Door
Style
3 Point
4 Point
5 Point
Gasket Type
Inflatable
Compression
#91000
#91003
#91001
#91004
#91002
#91005
Door Hardware Kit Order Number
*Note: Kits do not include
5/8” square bar or door hinges
Section 7
7-1
OVEN DOOR HARDWARE
• OUTSIDE DOOR HARDWARE
70348
For bi-parting doors less than 8’-0” tall, with inflatable
door
seals and 3 point latching.
Polar - outside door hardware (per set)
Quantity
No.
3
1
2
1
1
1
1
1
1
1
4
2
13
12
Description
S/S door cup bracket
Top lug
End bracket
Top center bracket
Bottom center bracket
Center lug
Adjustable door handle
Door handle hasp
Bottom lug
5/8” sq. latch bar (specify ht.)
1/4” x 1-1/2” S/S RH bolt
1/4” x 1-1/4” S/S RH bolt
1/4” x 1-1/4” S/S OH bolt
1/4” x 3/4” S/S HH bolt
75313
Part
70348
75251
75313
75265
75266
75267
75310
75273
75312
01522
10333
10525
10562
10444
75251
75265
75266
75267
75310
75273
01522
70619
75312
Please specify if ordering for doors with 1” x 2”
silicone gasket. Kit would include “T” handle, part
number 70619 and spacer tube.
• ADDITIONAL REQUIRED HARDWARE
FOR 4 LATCH DOORS OVER
8’-0” IN HEIGHT
Quantity
No.
1
70348
1
1
75266
1
75267
4
Description
Part
70348
S/S door cup bracket
Top center bracket
Bottom center bracket
Section 7
75265
Center lug
75266
1/4” x 3/4” S/S HH bolt
75265
75267
10444
7-2
OVEN DOOR HARDWARE
• INSIDE DOOR HARDWARE
10564
70353
Quantity
Description
Part No.
2
S/S door tongue assembly
70353
2
1/4” cable crimp clamp
10564
2
1/4” S/S lifting eye
75252
Specify Ht.
3/16” S/S cable
75253
2
S/S striker
70034
8
1/4” x 3/4” S/S RH bolt (B/S)
10330
1 3/16” S/S striker mounting bracket (B/S) 70375
2
1/4” x 3/4” S/S HH bolt (B/S)
10444
75252
70034
70375
• AIR REGULATOR ASSEMBLY
Part No. 45057
For use with inflatable door seal. Includes mounting bracket and
0 - 30 PSI gauge.
Part No. 66635
Air regulator bowl only
Air regulator only
Part No. 66282
• AIR VALVE - INSIDE Part No. 66469
Inside plug valve. For use with inflatable door seal.
• AIR VALVE - OUTSIDE
Part No. 66296
Outside clippard valve. For use with inflatable door seal.
• DOOR OPENER #410 Part No. 75233
• DOOR GASKET - HIGH TEMPERATURE
Part No. 15128
Special door gasket for high temperature ovens (262”).
Section 7
7-3
OVEN DOOR HARDWARE
• DOOR GASKET - REINFORCED INFLATABLE
Part No. 81000
Nitrile door gasket with nylon reinforcing. Custom made to size for oven
door. Comes with hose for door seal. (Specify oven serial number).
• DOOR GASKET - SILICONE
For access equipment access doors - 1” x 2” Part No. 15020
1/2” X 1” Part No. 15068
15020
15068
• DOOR HANDLE -ROUND Part No. 75280
End post only.
• DOOR HANDLE - ROUND Part No. 70456
11” Tube only - For large ovens
• DOOR HANDLE - ROUND Part No. 70457
6” Tube only - For 1 & 2 Truck Mini Ovens
• DOOR HANDLE
Part No. 75361
1-1/4” diameter x 12” one piece stainless steel handle.
• DOOR HINGE - STAINLESS STEEL
Flush hinge
Part No. 75360
1-1/8” offset
Part No. 75363
• DOOR HINGE - BOLTS
Part No. 10693
(9) Hexwasher bolt, 5/16” - 18 x 1” S/S
• DOOR SEAL HOSE
Part No. 15092
1/4” ID x 24” rubber hose.
• DOOR CENTER BLOCK Part No. 01589
For use with doors with inflatable gaskets.
Section 7
7-4
OVEN DOOR HARDWARE
• DOOR HINGE - KASON
Part No. 75152
#1245, 1-1/8” offset, high pressure, die-cast zinc with a highly polished
chromium plate finish. Self-closing and have a lift-off feature.
Hinges are interchangeable from right to left.
• DOOR HINGE - POLAR
Part No. 75122
Flush strap, 11-1/4” center of pin to end of strap, 3/8” plated
steel pin, holes drilled and countersunk for 1/4” FH screws.
Stainless steel.
• DOOR HINGE - POLAR
Part No. 75254
Offset strap, 11-1/2” center of pin to end of strap, 3/8” plated
steel pin, holes drilled and countersunk for 1/4” FH screws.
Stainless steel.
• DOOR HINGE - POLAR
Part No. 75274
411 S/S flush hinge. Replaces #401 chrome flush hinge.
• LATCH / HANDLE #4D
Part No. 75234
• LATCH / STRIKER
#3P Chrome polished 2-bolt
Latch
2-1/4” striker (short)
Part No. 75140
Part No. 75270
• LATCH / STRIKER
#4P Chrome polished 4-bolt
Part No. 75190
2-1/4” striker (short) Part No. 75192
3-1/4” striker (tall)
Part No. 75193
Latch
Section 7
7-5
OVEN DOOR HARDWARE
• MAGNET
Part No. 75342
Door, #5819K21
• PRESSURE SWITCH
Part No. 25161
ASCO JB57A215B
• REGULATOR, FILTER
Part No. 66487
• VALVE, CHECK
Part No. 31045
Brass, ¼” FPT x ¼” MPT
• VALVE, CHECK
Part No. 66310
Brass, pipe end, ¼” NPT
• VALVE, SOLENOID
Part No. 66424
8320G188, ¼”
Section 7
7-6
OVEN DOOR HARDWARE
• S/S SPECIAL ROLLER STRIKERS
Part No. 70256
•
• SILICONE DOOR GASKET ADHESIVE
Part No. 15042
#732 RTV silicone adhesive for use with silicone door gaskets,
10.3 oz. Tube.
• WINDOW FRAME S/S
Part No. 70447
2 window frames required per door.
• WINDOW GLASS
Part No. 75117
• WINDOW INSTALLATION TAPE
Double sided tape for use in installing window frames and glass.
1 roll: 1/2” x 36 yds. Part No. 75277
Gortex gasket (14 ft. / window)
Part No. 15097
Section 7
7-7
CLEANING SYSTEM COMPONENTS
• BRONZE QUICK-COUPLE CONNECTORS
1-1/2” NPT, 633-A female
Part No. 66281
1-1/2” NPT, 633-D female
Part No. 66425
(with handles)
• NYLOBRADE HOSE
1-1/2” ID
2” ID
Part No. 66427
Part No. 66279
• SPRAY NOZZLES
Size NPT Material
Type
1/4”
Brass
TF10FC Spiral
1/4”
S/S
TF10FC Spiral
3/8”
Brass
BNM Full Cone
3/8”
S/S
BNM Full Cone
3/8”
Brass
TF16FC Spiral
3/8”
Brass
TF12-170 Spiral
3/8”
S/S
TF12-170 Spiral
Area Used
Part No.
Smoke & Exhaust Duct
66084
Smoke & Exhaust Duct
66177
Equipment: Supply/Recirc 66481
Equipment: Supply/Recirc 66482
*see note
66127
Steam Coils
66301
Steam Coils
66341
Note: The 3/8” TF16FC type nozzle is use in place of the 3/8” MP156 type
nozzle when NO cleaning pump is used.
• STANDARD CLEANING PUMP ASSEMBLY
Close-coupled pump/motor combination with capacitor start.
3450 RPM, 2 HP, 1-1/2” NPT port size. Includes nylobrade hose,
quick-couple connector assembly, filter foot, and shaft guard.
1 phase unit
3 phase unit
Section 8
Part No. 45051
Part No. 66523
8-1
SMOKE/EXHAUST SYSTEM COMPONENTS
• AIR ACTUATOR MOTOR - 3”
Part No. 05131
For old style clapper damper.
• BELTING, “V” Power Twist
Part No. 35525
Adjust to size. Approximately 8-1/2 ft per fan.
• EXHAUST FANS
Belt driven, 304 S/S, smoke and heat transmitted to 500 F. Fans
do not
include motor, motor sheave, or belts. Note: Fan motors vary on
speed
and RPM’s according to design. Old style fans (18” & 24”) are
no longer
available. Only the replacement fan blades, shafts, and bearings.
Old style
New style
New Style Exhaust Fans:
Size
Static Pressure
Part No.
12”
1/4”
45018
18”
1/4”
45143
18” (for 24” duct) 1/4”
Fan RPM
CFM
2,000
1,500
1,500
3,500
2,500
7,500
• EXHAUST FAN - TRANTORQUE BUSHING
Part No. 35526
Used to hold fan blade. (New style fans only).
• EXHAUST FAN ADAPTER RINGS
Part No. 70553
Used to install 18” fan into 24” ductwork. Requires 2 per fan.
Section 9
9-1
SMOKE/EXHAUST SYSTEM COMPONENTS
• EXHAUST FAN BEARINGS
Fan Size
Bearing Size
12”
18” old style
18” new style
24” old style
3/4”
1”
1”
1-3/16”
Part No.
35251
35245
35527
35249
35251
35245
35249
35527
• EXHAUST FAN MOTORS
1 HP for 12” fans
3 HP for new 18” fans (18” ductwork)
5 HP on new 18” fans (24” ductwork)
Part No. 05019
Part No. 05162
Part No. 05022
Note: Installing 18” fan into 24” ductwork requires 2
adapter rings (part no. 70553)
• EXHAUST FAN REPLACEMENT BLADES
12”
Part No. 70385
18” old style
Part No. 70319
18” new style
Part No. 40148
24” old style
Part No. 70359
Old style
New style
• EXHAUST FAN SHAFT
12”
18” old style
18” new style
24” old style
Section 9
Part No. 70386
Part No. 70387
Part No. 40150
Part No. 70388
9-2
SMOKE/EXHAUST SYSTEM COMPONENTS
• FAN - SMOKE INJECTION
S/S fan complete with 1 HP motor, 230/460 V., 60 Hz.,
3 phase, 1800 RPM.
Complete assembly Part No. 45019
Replacement fan blade only (5/8” dia. Bore) Part No. 40085
• MOTOR DIAPHRAMS - AIR
For old style clapper damper
Part No. 05065
(prior to 1981)
• MOTOR LINKAGE KIT
For old style clapper damper
Part No. 05132
• SEALANT
732 RTV Silicone Sealant
ASI 600 F. high temperature
15042
Part No. 15042
Part No. 15114
15114
• SMOKE DUCT ELBOW
Part No. 70345
Standard 7” diameter smoke duct elbow with angle rings.
• SMOKE DUCT CONNECTING RING
Part No. 70345
7” diameter galvanized angle ring.
Section 9
9-3
SMOKE/EXHAUST SYSTEM COMPONENTS
• LIQUID SMOKE ATOMIZING
303 spray setup 1/4”
Part No. 66389
• LIQUID SMOKE SOLENOID VALVE
8262G220, 1/4”
Part No. 66421
• KIT, TEFLON DISC
Part No. 66389
• WASHER, GASKET
Teflon, white
Section 9
Part No. 75330
9-4
ALKAR SMOKE GENERATOR PARTS
• CONTROLLER
Part No. 25296
Temperature control from 0 - 400 F. 115 VAC.
• TYPE J THERMOCOUPLE SENSOR
Part No. 25202
Used to monitor temperature.
• HEATING ELEMENTS
For burning of sawdust located on the sawdust feed plate.
230V (SGD-22B) 2400 watt
460V (SGD-22A) 2400 watt
• HEATER
Part No. 30981
Part No. 30977
Part No. 30967
AS8H5X-KRP 2R204 Thermolink
• PUSH BUTTON RESET TIMER
Part No. 30950
Provides an accurate, adjustable time delay or timed interval for control
of a load circuit. Push-button to start sawdust feed for preset time.
• TIME DELAY / RELAY W/BASE
Part No. 30881
Controls the preheating time of the heating element before smoke
cycle is started. Adjustable from .33 to 10 minutes.
• GEAR MOTOR
Part No. 05150
Dayton, #3M095, 1RPM
• ROPE GASKET
Part No. 15123
Ceramic ¾” diameter
• HEAT SWITCH
Part No. 30968
IC-2W
Section 10
10-1
ALKAR SMOKE GENERATOR PARTS
• TRANSDUCER
Part No. 25307
This unit is supplied by a 4 to 20 ma. Signal and converts it to
a 3 to 15 psig output.
• SAWDUST DRIVE MOTOR - DC
Part No. 05151
Drives the sawdust feed.
• SAWDUST DRIVE SPEED CONTROLLER - DC
Part No. 05152
Direct current controller used to adjust the speed of the sawdust
drive DC motor. Graham #600 series DC controller.
• DETECT-A-FIRE SENSOR
Part No. 25145
A precision temperature sensor to detect excessive heat in the combustion
box. Opens on rise in temperature. Non-adjustable 325 F.
• TIMER
Part No. 31501
Used to intermittently turn the system on or off at timed intervals.
• TIMER BASE
Part No. 31502
For use with timer part no. 31501.
• SAWDUST DRIVE GEAR REDUCER - LESS MOTOR
Part No. 35319
A worm-gear speed reducer to regulate the feed of sawdust
into the combustion box. 2000:1 ratio.
• AIR REGULATOR ASSEMBLY
Complete assembly
Part No. 45057
Regulator only
Part No. 66282
Section 10
10-2
BRINE CHILLER & CONTINUOUS LINE PARTS
• CONVEYOR CHAIN
Part No. 35144
For 6” stick centers. Stainless steel, 2” pitch supplied in 10 foot sections.
Minimum 20 ft. Replace left and right side in equal amounts.
• MASTER LINKS
Part No. 35137
Full master link for S/S continuous line 2” pitch chain.
Available in half links.
• CONVEYOR CHAIN CHANNELS, S.S.
10 ft length of supply track
Part No. 70673
10 ft length of return track
Part No. 70672
• CONVEYOR CHAIN REPLACEMENT ROLLERS (2 pc snap-on)
Part No. 35496
• CARRIER BLOCKS
35253
For S/S continuous line chain. Closed Blocks Part No. 35253
35255
Open Blocks Part No. 35145
For S/S chill tunnel chain.
Closed Blocks Part No. 35255
Open Blocks Part No. 35254
35254
35145
• CARRIER BLOCK FASTENERS
For Alkar Quick Chill Tunnels. 3/16” x 3/8” S/S RH. Part No. 10575
For Continuous Line Systems. #12 x 7/16” S/S HH. Part No. 10498
10575
10498
• MEAT STICK
For In-Line Continuous Hot Dog Systems.
61” long, 1/2” diameter, 17-4 ph S.S.
Part No. 70591
• CONVEYOR CHAIN LUBRICANT
Part No. 66520
AccuLube LB 2000 in one gallon size. Lubricant for continuous line chain.
Section 11
11-1
BRINE CHILLER & CONTINUOUS LINE PARTS
• CONVEYOR CHAIN
Stainless steel chain for Continuous Serpentine System.
• BUSHING
Part No. 35542
Celcon bushing for serpentine carrier trays.
• RETAINER RING, SERPENTINE CARRIER TRAY
1” diameter
Part No. 10705
5/8” diameter
Part No. 10706
• CELCON PLUG/ O-RING
Replaces slip caps.
Plug
Size
1-1/2”
2”
2-1/2”
3”
4”
Part No. 66463
Part No. 66470
Part No. 66472
O-ring
Part No. 66464
Part No. 66471
Part No. 66473
-------------------
-------------------
• SLIP PINS - S/S
For slip connections.
Tube Size
Number
1-1/2” to 2”
C4-25
2-1/2” to 3”
C4-35
4”
C4-45
Part No.
60160
60161
60162
• DIAL THERMOMETER
Range 0 - 200 F. Part No. 60185
Section 11
11-2
BRINE CHILLER & CONTINUOUS LINE PARTS
• CLAMPS AND GASKETS
The industry standard quick disconnect method for process piping systems
provides flush, leakproof, sanitary joints meeting 3A Standards. Heavy duty
clamps provide protection against leakage or misalignment and are locked
mechanically with an adjustable wing nut. The one piece molded O-ring
gaskets are made of Buna N composite rubber and provide a dependable
economical method of sealing.
Tube Size (O.D.)
1-1/2”
2”
2-1/2”
3”
4”
6”
8”
#13 Clamp
Part No. 60013
Part No. 60174
Part No. 60175
Part No. 60176
Part No. 60126
Part No. 60177
Part No. 60178
• FLANGE BEARING
#40 Gasket
Part No. 60167
Part No. 60168
Part No. 60169
Part No. 60170
Part No. 60171
Part No. 60172
Part No. 60173
Part No. 35371
For continuous line, 4 bolt, 2-3/16” bore, polymer
• FLANGE BEARING REPLACEMENT INSERTS
Part No. 35259
For continuous line, 2-3/16” bore replacement inserts.
• FLOAT SWITCH
Part No. 31469
For base tank and reservoirs on Serpentine Continuous Systems
• LIMIT SWITCH
Part No. 31035
For brine chiller door, pre-wired, supplied with 8 ft of cable and
stainless steel roller. Model #802MC-AY8.
Section 11
11-3
BRINE CHILLER & CONTINUOUS LINE PARTS
• LIMIT SWITCH
Part No. 31483
For brine chiller door, Model #C2B-JK2.
• NOZZLE ASSEMBLY
Part No. 66409
1” LEM - 12, PVC.
• SPRAY NOZZLES
Stainless steel, T-316 nozzles available in 120 degree full cone or
145 degree flat spray type.
Size
3/8”
1/2”
1/2”
1/2”
3/4”
3/4”
3/4”
3/4”
Full Cone Nozzles
Model No.
MP187W
MP187W
MP218W
MP250W
MP281W
MP312W
MP343W
MP375W
Part No.
66373
66374
66375
66376
66377
66378
66379
66380
Size
3/8”
1/2”
1/2”
1/2”
1/2”
Flat Spray Nozzles
Model No.
FF187145
FF218145
FF250145
FF312145
FF375145
Part No.
66381
66402
66403
66404
66405
Section 11
11-4
BRINE CHILLER & CONTINUOUS LINE PARTS
• NOZZLE INSERT ADAPTERS
1/4” (#568) Delrin
Part No. 65664
3/8” (#569) Delrin
Part No. 66017
1/2” (#570) Delrin
Part No. 66283
• NOZZLE - BRINE SPRAY
Part No. 66503
3/8” (BSS20) S/S Part No. 66407
1/4” (8050) S/S
• NOZZLES - CLEANING
Stainless steel
Size
3/8”
1/4”
3/8”
3/8”
Model No.
TF16FC
TF10FC
BNM
TF12-170
• RTD PROBE
Part No.
66408
66177
66482
66341
Type
Spiral
Spiral, smoke & exhaust duct
Full cone, equip. supply & recirc
Spiral, steam coils
Part No. 25257
Liquid temperature sensor for use in continuous systems and brine chillers.
• SOLID END CAPS - S/S (#16A)
1-1/2” Part No. 60179
2”
Part No. 60180
2-1/2” Part No. 60181
3”
Part No. 60182
4”
Part No. 60183
6”
Part No. 60166
8”
Part No. 60348
• TRIP DOG
Part 60140
Cast stainless steel with pivot pin and cotter pin. Standard length
is 3” from center of pivot pin to the bottom of the dog.
Section 11
11-5
TREES, TRUCKS, CAGES, AND COMPONENTS
• 4” TROLLEY ASSEMBLY
Part No. 90260
Hardened S/S construction with electro polished finish withstands
steam and brine environments. 3000 lb capacity.
• 4” TROLLEY WHEELS ONLY
Part No. 90200
Hardened S/S construction, 4” diameter, 1/2” arbor.
• ALKAR PRODUCT TRUCKS (Std size is 42”W x 46-1/2”L x 72”H)
Standard 4 station meat truck
Part No. 45022
Standard 5 station meat truck
Part No. 45066
Note: Other sizes and configurations available. Call with specifications.
• ALKAR TREES AND CAGES
Custom designed to your requirements.
• DROP KNUCKLE RAIL ASSEMBLY
Part No. 70575
Stainless steel.
• TRUCK CASTERS AND WHEELS
Plexite caster wheels. Available with both 6” and 8” wheels,
stem type and plate type, rigid and swivel. Swivel type have
ball bearings with grease zerk for lubrication.
Stem Type: 6” Rigid
6” Swivel
8” Rigid
8” Swivel
Plate Type: 6” Rigid
6” Swivel
8” Rigid
8” Swivel
Section 12
Part No. 75102
Part No. 75036
Part No. 75218
Part No. 75219
Part No. 75357
Part No. 75356
Part No. 75359
Part No. 75358
12-1
TREES, TRUCKS, CAGES, AND COMPONENTS
• REPLACEMENT CASTER WHEELS ONLY
Plexite wheels for replacement.
8”
Part No. 75306
• RAIL HANGERS
Made to specified length. 2-1/2” x 1/2” #304 stainless steel. MADE TO ORDER.
Section 12
12-2
SAFETY LABELS – ANSI Z535.4 Compliant
All labels are adhesive-backed laminated polyester, ANSI (American National
Standards Institute) Z535.4 compliant. Bilingual – graphical format – both
Spanish and English
• NOTICE / INFORMATION LABELS
Cold Liquid
Part No. 90008L
Test Glycol
Part No. 90016L
Test Brine
Part No. 90017L
Bearing Lubrication
Part No. 90018L
Do NOT Use Chlorine Sanitizers
Part No. 90019L
General Rotation, Circle
Part No. 90032L
General Rotation, Linear
Part No. 90033L
General Air Flow, Linear
Part No. 90034L
• SAFETY INSTRUCTIONS LABELS
Lockout – Tagout Procedure
Part No. 90020L
Chill Plates / Turn Off Ammonia
Part No. 90021L
Roof Not Safe
Part No. 90022L
Section 13
13-1
SAFETY LABELS – ANSI Z535.4 Compliant
All labels are adhesive-backed laminated polyester, ANSI (American National
Standards Institute) Z535.4 compliant. Bilingual – graphical format – both
Spanish and English
• CAUTION LABELS
Falling Hazard/ Do not
operate with door open
Part No. 90003L
Hot Surface
Part No. 90004L
Automatic Conveyor Moves
Part No. 90005L
Burn Hazard / Hot Water
Part No. 90006L
Burn Hazard / Steam or Air
Part No. 90007L
Pinch Points
Part No. 90009L
Pinch Points / Sprocket & Chain
Part No. 90010L
Falling Hazard (general)
Part No. 90012L
• DANGER LABELS
Hazardous Voltage
Section 13
Part No. 90014L
13-2
SAFETY LABELS – ANSI Z535.4 Compliant
All labels are adhesive-backed laminated polyester, ANSI (American National
Standards Institute) Z535.4 compliant. Bilingual – graphical format – both
Spanish and English
• WARNING LABELS
Crush and Cut Hazard (general, gear)
Part No. 90000L
Read Manual
Part No. 90001L
Confined Space
Part No. 90002L
Crush and Cut Hazard / Belts
and Sheaves
Part No. 90011L
Hazardous Gas
Part No. 90013L
Cut Hazard
Part No. 90031L
Corrosive Chemicals
Part No. H6023L
Section 13
13-3
SAFETY LABELS – ISO 3584 Compliant
All labels are adhesive-backed laminated polyester, ISO (International
Standards Institute) 3584 compliant. Graphical Format
• INFORMATIONAL LABELS (non-ISO compliant)
General Rotation / Linear (to right)
Part No. 78040L
General Rotation / Circle (to right)
Part No. 78041L
General Rotation / Circle (to left)
Part No. 78042L
• MANDATORY ACTION LABELS
Lockout Electrical Power
Part No. 60110L
Consult Operator’s Manual
Part No. 60170L
Consult Service Manual / Test
Glycol & Brine
Part No. 60180L
Wear Hardhat
Part No. 60420L
Wear Eye Protection
Part No. 60400L
Wear Ear Protection
Part No. 60410L
Wear Safety Gloves
Part No. 60330L
Section 14
14-1
SAFETY LABELS – ISO 3584 Compliant
All labels are adhesive-backed laminated polyester, ISO (International
Standards Institute) 3584 compliant. Graphical Format
• PROHIBITIVE ACTION LABELS
Do Not Operate with
Guard Removed
Part No. 60600L
No Access for
Unauthorized Persons
Part No. 60620L
• WARNING LABELS
Cutting of Fingers / Hand (angled blade) Part No. 10000L
Cutting of Fingers / Hand (straight blade) Part No. 10010L
Hand Entanglement / Belt Drive
Part No. 10110L
Hand Entanglement / Belt & Rollers
Part No. 10090L
Hand Entanglement / Chain Drive
Part No. 10120L
Hand Entanglement / Rotating Gears
Part No. 10140L
Hand Crush / Force From Above
Part No. 10170L
Cutting of Fingers / Hand (rotating blade) Part No. 10270L
Section 14
14-2
SAFETY LABELS – ISO 3584 Compliant
All labels are adhesive-backed laminated polyester, ISO (International
Standards Institute) 3584 compliant. Graphical Format
• WARNING LABELS (cont.)
Explosion Hazard / Release of
Pressure
Part No. 40050L
Asphyxiation Hazard / Poisonous
Fumes OR Toxic Gas
Part No. 40060L
Fall Hazard / Edge of Equipment
Part No. 50350L
Cutting or Arm or Body / Mixer
Part No. 50660L
Fall Hazard (general)
Part No. 50790L
Lifting Hazard
Part No. 51010L
Electrical Shock / Electrocution
Part No. 60100L
Corrosive Material
Part No. 60230L
Burn Hazard / Hot Surface
Part No. 60430L
Low Temperature
Part No. 60440L
Automatic Start-up
Part No. 60450L
Section 14
14-3
SAFETY LABELS – ISO 3584 Compliant
All labels are adhesive-backed laminated polyester, ISO (International
Standards Institute) 3584 compliant. Graphical Format
• WARNING LABELS (cont.)
Burn Hazard / Hot Liquids
Part No. 60680L
Loud Noize
Part No. 61040L
Do Not Enter / Confined Space
Part No. 61110L
Section 14
14-4