Project: ______________________ Indirect-Direct T5/T5HO SCEP Option BRM4 3 T5/T5HO WHR 5HO WHR 5HO WHR Type: ________________________ Bruno I/D 5HO WHR Suspended S P E C I F I C AT I O N S BRM4 ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ _____________________ LAMPING OPTIONS BRM4 - 1 BRM4 2 T5/T5HO WHR BRM4 3 T5/T5HO WHR BRM4 - 2 1 3⁄4” 1 3⁄4” ⁄2” ⁄2” 1 8 1⁄4” 1 8 1⁄4” BRM4 2 T5/T5HO WHR BRM4 1 T5/T5HO WHR SPECIFICATIONS 1 3⁄4” ⁄2” 1 8 1⁄4” BRM4 - 3 Construction Nominal 8 1⁄4” x 1 3⁄4” rectangular housing is formed from cold-rolled steel. Die-cast end caps are mechanically attached with no exposed fasteners. blade or white painted, perforated blade. Each available with optional acrylic opal overlay. consult factory. Plug-in electrical connectors included. UL and C-UL listed. Finish Luminaire Length Reflectors Die-formed specular reflector with 95% reflectance. Fine textured white polyester powder BRM4 1 T5/T5HO WHR paint is standard. Consult factory for special finish requirements. Shielding /Baffle Electrical Choose one of four parabolic baffle options: semispecular, white painted, semi-specular perforated 4’ 3⁄8”, 8’ and 12’ lengths in a single section for nominal support spacing at 4’, 8’ and 12’. For total luminaire length, add 5⁄8” for each flat end cap and 4” for each sculptured end cap. Using internal joiners, 4’, 8’ and 12’ sections can be joined to form longer rows. Specify 120V, 277V or 347V. Pre-wired with 16AWG fixture wires. For special circuiting or wire gauge, CATALOG NUMBER Examples: BRM4 2 28T5 SPR SSB 40FT R8 277 GEB10 DCT LP835 F1/18 C210 SCEP — BRM4 3 54T5HO SPR WPB 32FT R8 277 GEB10 1SE EL DCT LP835 F1/21 C110 ________ _______ _______ __________ Luminaire # of Lamp Type Reflector Lamps 28T51 28W T5 BRM4 SPRSpecular in 54T5HO54W T5HO reflector Cross Section __________ __________ __________ _________ __________ _______ Distribution Shielding Baffle Luminaire Row Length Maximum Section Length Voltage Ballast Type (Blank)Standard (Blank) 65/35 OPDOpal 2 20/80 20% up, overlay 80% down 40/60240% up, 60% down 0/10020% up, 100% down CLI3 Center lamp isolater 1 2 3 SSBSemi-specular baffle WPB White painted baffle SSPSemi-specular perforated blade baffle WPP White painted perforated blade baffle X FT R4 (4’ increments) R8 R12 _______ _______ _______ ________________ ______________ ______________ # of Emergency Modules Emergency Type5 Switching Lamp Color SCTSingle circuit DCTDual circuit L/LP LP830 LP835 LP841 Mounting Type / Overall Finish Suspension C110Painted F1/ T-bar ceiling (Blank)None 1SE 1 section 2SE 2 sections XSE X sections Notes: (Blank)None ECEmergency circuit EL1Emergency battery pack 1 EN Emergency battery pack w/night light circuit 1 Not available in 347V 2 Nominal distribution, refer to photometric tests for exact distribution. Not available with DU option No lamp 3000k 80+ CRI 3500k 80+ CRI 4100k 80+ CRI Available with T5 only: LP830P3000K 80+ CRI Premier LP835P3500K 80+ CRI Premier LP841P4100K 80+ CRI Premier Reference Lamp Chart on website or consult factory for other options. (universal mounting bracket) F1A/ T-bar ceiling (UMB with integrated J-box) F2/ Hard ceiling (horizontal J-box) F3/ Rigid stem 1212” 1515” 1818” 2121” 2424” XXXX” Overall suspension is measured from ceiling to bottom of luminaire. 3 Available with 3-lamp cross section luminaires only 4 Not available with 28T5 lamps 5 Emergency type is installed in last 4’ of luminaire sections ______________ aluminum (low gloss) C210White white (finetextured low gloss) C099Custom finish 4’ section(s) 8’ section(s) 12’ section(s) 120 277 347 __________ GEB10<10% THD Electronic ADEZ1,4Advance Mark 10 dim DMHL3D1Lutron Hi-Lume dim OSDIM1,4Osram 0-10V dim Reference Ballast Wizard on website or consult factory for other options. _________________________________ Options ACG Adjustable cable grippers BLK Black cord, cord manager and canopy (not available with F3) CP Chicago plenum (available with F1A only) DL Damp location label DU6 Dust cover ELH Emergency through wiring w/separate feed ELS Emergency through wiring w/single feed, shared neutral ELS2 Emergency through wiring w/single feed, separate neutrals GLR Fusing (fast blow) GMF Fusing (slow blow) MCS Matching feed canopy at support NEPP5D nLight enabled control module per row/zone NYC New York City code OJB Offset junction box SCEP Sculptured end cap SLP Sloped ceiling (for 10-45°, must be specified with F2, ACG and OJB options) XXXX Integrated sensor; choose options and obtain code on page 2 Separate feed required unless ELS or ELS2 is specified. 6 Not available with 3-lamp T5HO cross section 2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: techsupport@peerlesslighting.com • PeerlessLighting.com © 2013 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Peerless Bruno” are registered trademarks of Acuity Brands Lighting. Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice. 1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx BRM4 Bruno I/D Indirect-Direct T5/T5HO 1 Bruno I/D Type: ________________________ Project: ______________________ Indirect-Direct T5/T5HO Suspended BRM4 INTEGRATED NLIGHT MICRO SENSOR Determine the appropriate sensor type, network type and sensor power source for your application. Enter the code in the Options section of the Catalog Number. EXAMPLE: PDT1 Network Type & Sensor Power Source (choose one) Sensor Type (choose one) ADC nLight model nES ADCX Daylight Dimming Specify 0-10V dimming ballast No occupancy sensing PDT nLight model nES PDT7 ADCX Daylight Dimming and/or Occupancy Detection Specify 0-10v dimming ballast for daylight dimming Specify fixed-output ballast for occupancy detection only (daylight dimming disabled) 1* nLight-Enabled (Network-Ready) with Luminaire-Integrated Power Pack 10’ Cat-5e cable and splitter provided 2 Standalone Operation (No Networking) with Luminaire Integrated Power Pack No Cat-5e cable provided 3* nLight-Enabled (Network-Ready) with Remote nLight Power Pack or nPanel 10’ Cat-5e cable and splitter provided Order required remote nLight Power Pack or nPanel separately through nLight (Acuity Brands Controls) For more information about the Integrated nLight Micro Sensor, its capabilities and options, download the PDF guide at: PeerlessLighting.com/nLight-Sensor-Guide *nLight-Enabled (network-ready) options include one RJ-45 connector on the luminaire and 10’ of Cat-5e cable and a splitter to control the entire luminaire row (depending on wattage/voltage limitations). The Cat-5e cable drop is located in the same section as the sensor. For multiple zones, please contact techsupport@peerlesslighting.com. WEIGHTS & SUPPORT SPACING Suspension spacing equals section length. Default location shown. Consult factory for stem mounting suspension spacing and alternate locations. STANDARD SECTIONS Key: 4’-0 3⁄8” 22 LBS ⁄8” standard flat end plates 4” optional sculptured end plates 5 4’-1 ⁄8” O.A. 5 •Support or feed location xPlease consult factory for sensor placement 8’-0” 38 LBS 8’-1 1⁄4” O.A. 12’-0” 54 LBS 12’-1 1⁄4” O.A. PLAN VIEW CONFIGURATIONS Tenon “L”, “T”, “X” and straight connectors available for suspended configurations. Reference Pattern Connector Guide for additional details. PHOTOMETRICS Actual performance may differ as a result of end-user environment and application. 1-LAMP T5HO 88.8% efficiency 4438 delivered lumens 2-LAMP T5HO 88.8% efficiency 8804 delivered lumens 3-LAMP T5HO 83.0% efficiency 12445 delivered lumens 68.2% up / 31.8% down 59.4% up / 40.6% down 65.7% up / 34.3% down 1-LAMP T5HO WITH OPD 88.3% efficiency 4415 delivered lumens 84.2% up / 15.8% down 2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: techsupport@peerlesslighting.com • PeerlessLighting.com © 2013 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Peerless Bruno” are registered trademarks of Acuity Brands Lighting. Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice. 1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx BRM4 Bruno I/D Indirect-Direct T5/T5HO 2 Bruno I/D Type: ________________________ Project: ______________________ Indirect-Direct T5/T5HO Suspended PHOTOMETRICS BRM4 Actual performance may differ as a result of end-user environment and application. 1-LAMP T5HO WITH 40/60 VDR 77.2% efficiency 3861 delivered lumens 2-LAMP T5HO WITH 40/60 VDR 75.4% efficiency 7541 delivered lumens 3-LAMP T5HO WITH 40/60 VDR 74.6% efficiency 11189 delivered lumens 40.6% up / 59.4% down 39.0% up / 61.0% down 40.4% up / 59.6% down 1-LAMP T5HO WITH 20/80 VDR 72.5% efficiency 3626 delivered lumens 2-LAMP T5HO WITH 20/80 VDR 69.4% efficiency 6942 delivered lumens 3-LAMP T5HO WITH 20/80 VDR 67.4% efficiency 10118 delivered lumens 18.1% up / 81.9% down 18.5% up / 81.5% down 20.3% up / 79.7% down 1-LAMP T5HO WITH 0/100 VDR 67.7% efficiency 3385 delivered lumens 2-LAMP T5HO WITH 0/100 VDR 62.3% efficiency 6233 delivered lumens 3-LAMP T5HO WITH 0/100 VDR 57.9% efficiency 8678 delivered lumens 1.0% up / 99.0% down 2% up / 98% down 1.5% up / 98.5% down 2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: techsupport@peerlesslighting.com • PeerlessLighting.com © 2013 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Peerless Bruno” are registered trademarks of Acuity Brands Lighting. Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice. 1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx BRM4 Bruno I/D Indirect-Direct T5/T5HO 3