2.136
Accessories, Splices
and Connectors
Splices and Connectors ............................. Pgs. 137-142
Misc. Accessories ....................................................Pg. 143
Ground Connectors .................................... Pgs. 143-144
Separators ...................................................... Pgs. 145-147
CABLE TRAY
Splices and Connectors
Universal Splice Connectors for All Straight Sections and Fittings
These connectors are furnished with trays and are also available to purchase separately,
if required for field cuts. Sold as EACH. (Hardware included)
Tray Height
HDGAF
Steel
Alum.
SS
304
SS
316
Galvannealed
(Husky Way)
3-3/8”,4”,4-1/2”
ASP-H2
SSP-H2
4SP-H2
6SP-H2
NSP-H2
6”,6-1/4”,7”
ASP-M2
SSP-M2
4SP-M2
6SP-M2
NSP-M2
I6 (10 Bolt)
ASP-E2
——
——
——
——
I8 (10 Bolt)
ASP-I8
——
——
——
——
´ ([FHSW,
ASP-L1
10”
ASP-D1
WITH (1)
BLANK SIDE
1RWH$GG%WRWKHFDWDORJQXPEHU
IRUDVSOLFHSODWHZLWK03+XVN\KROH
SDWWHUQRQRQHVLGHDQGDEODQNVLGHIRU
¿HOGGULOOLQJWRPDWFKDQRWKHUPDNHWUD\
system.
3-3/8”,4”,4-1/2”
ASP-H2-1B
SSP-H2-1B
4SP-H2-1B
6SP-H2-1B
NSP-H2-1B
6”, 6-1/4”, 7”
ASP-M2-1B
SSP-M2-1B
4SP-M2-1B
6SP-M2-1B
NSP-M2-1B
´ ([FHSW,
ASP-L1-1B
10”
ASP-D1-1B
([FHSW,
Expansion Joint Splice Plates
11-ACCESSORIES
Expansion splice plates for Ladder or Trough are designed to allow 1-1/2” free movement between adjacent straight lengths. When using expansion splices, it is important
that the straight run be fixed permanently to its support at the approximate center between expansion joints whenever possible, and that all other points be supported in a
manner that the longitudinal expansion is not restricted. Supports should be provided
within one foot on each side of an expansion joint to ensure its proper functioning. Sold
as EACH. (Hardware included)
7,36HH1(0$9(IRUSURSHULQVWDOODWLRQ
LQVWUXFWLRQVUHJDUGLQJIUHTXHQF\RIXVH
DQGVHWWLQJWKHJDSGXULQJLQVWDOODWLRQ
%RQGLQJMXPSHUVUHTXLUHG
Tray Height
Or Type
Alum.
HDGAF
SS
304
SS
316
Galvannealed
(Husky Way)
3-3/8”,4”,4-1/2”, G4
ASP-4-EX
SSP-4-EX
4SP-4-EX
6SP-4-EX
NSP-4-EX
6”,6-1/4”, 7”, G6
ASP-6-EX
SSP-6-EX
4SP-6-EX
6SP-6-EX
NSP-6-EX
I6
ASP-I6-EX
——
——
——
——
I8
ASP-I8-EX
——
——
——
——
´ ([FHSW,
ASP-8-EX
——
——
——
——
10”
ASP-10-EX
——
——
——
——
90° Splices for Trough, Ladder and Channel
These splices are used for field cut tees if there is no room for bends or fittings. Also used
for attachment to metal enclosures. Sold as EACH.
+DUGZDUHLQFOXGHG
864.234.4800
m p h u s k y. co m
Tray Height
Or Type
Alum.
HDGAF
SS
304
SS
316
Galvannealed
(Husky Way)
3-3/8”,4”,4-1/2”, G4
ASP-4-90
SSP-4-90
4SP-4-90
6SP-4-90
NSP-4-90
6”,6-1/4”, 7”, G6
ASP-6-90
SSP-6-90
4SP-6-90
6SP-6-90
NSP-6-90
I6
ASP-I6-90
——
——
——
——
I8
ASP-I8-90
——
——
——
——
´ ([FHSW,
ASP-8-90
——
——
——
——
10”
ASP-10-90
——
——
——
——
137
Copyright 2013 MP Husky. All rights reserved.
CABLE TRAY
Splices and Connectors
Step Down Splice
Used to connect 6”-7” tray to 3-3/8”- 4-1/2” tray (Except I6).
(Hardware included)
Alum.
HDGAF
SS
304
SS
316
Galvannealed
(Husky Way)
ASP-MH2
SSP-MH2
4SP-MH2
6SP-MH2
NSP-MH2
Hinged Splices
Horizontal
Channel -----
Vertical
Tray Depth or
Type
Alum.
Mill
Galv.
SS
304
SS
316
HDGAF
(Husky Way)
Galvan.
3-3/8”,4”,4-1/2”
AFS-H4
SFS-H4
4FS-H4
6FS-H4
n/a
NSF-H4
6”,6-1/4”,7”
([FHSW, ,
AFS-H6
SFS-H6
4FS-H6
6FS-H6
n/a
NSF-H6
I6
AFS-HI6
——
——
——
——
——
I8
AFS-HI8
——
——
——
——
——
´ ([FHSW,
AFS-H8
——
——
——
——
——
10”
AFS-H10
——
——
——
——
——
4” CHANNEL(G4)
AFS-H4G
SFS-H4G
4FS-H4G
6FS-H4G
GFS-H4G
——
6” CHANNEL(G6)
AFS-H6G
SFS-H6G
4FS-H6G
6FS-H6G
GFS-H6G
——
Tray Depth or
Type
Alum.
Mill
Galv.
SS
304
SS
316
HDGAF
(Husky
Way)
3-3/8”,4”,4-1/2”
$)69
6)69
)69
)69
*)69
16)9
6”,6-1/4”, 7”
([FHSW, ,
$)69
6)69
)69
)69
*)69
16)9
I6
$)69,
——
——
——
——
——
I8
$)69,
——
——
——
——
——
´ ([FHSW,
$)69
——
——
——
——
——
10”
$)69
——
——
——
——
——
4” CHANNEL(G4)
$)69*
6)69*
)69*
)69*
n/a
——
6” CHANNEL(G6)
$)69*
6)69*
)69*
)69*
n/a
——
Galvan.
Channel -----
$ERYHSDUWQXPEHUVDUHIRUSDLU ZLWKWKHH[FHSWLRQRI* *²WKH\DUHHD +DUGZDUHLVLQFOXGHGZLWKWKH
DERYHLWHPV
Copyright 2013 MP Husky. All rights reserved.
138
864.234.4800
m p h u s k y. co m
11-ACCESSORIES
NOTE: Only for use with
an angle of 30o or less
Horizontal and vertical hinged splices offer field flexibility to go around pipes, ducts,
and other obstacles that occur during installation. Electrical continuity is maintained by
using bonding jumpers such as AFS-C, which are purchased separately. Hinged splices for
Ladder or Trough come in sets of two. Hinged splices for 4” and 6” Channel come as single
units. Horizontal hinged splices require field drilling of the long hinge member and all
hinged splices require additional supports, as they are not considered to be full strength
mechanical splices. Sold in PAIRS. (Hardware included)
CABLE TRAY
Splices and Connectors
Channel Splice Plates
Husky 4” and 6” wide Channel systems are supplied with the following wrap-around
splice plates and hardware. Additional splice plates for field cuts can be ordered by the
following catalog numbers. (Hardware included)
Type
Width
Alum.
HDGAF
SS 304
SS 316
4” G4
Channel
4
ASP-Y2
SSP-Y2
4SP-Y2
6SP-Y2
6” G6
Channel
6
ASP-X2
SSP-X2
4SP-X2
6SP-X2
Box Connectors for Ladder and Trough
11-ACCESSORIES
Box connectors terminate Ladder or Trough at Switchgear housings or
other metal structures. (Splice hardware included)
Tray
Type
Alum.
Mill Galv.
HDGAF
SS
304
SS
316
Galvannealed
(Husky Way)
HA, ASH6, PSH0, NSH0
$9%& 9%& GBC-( )-3-3/8
9%& 9%& 19%& J2,NSJ0,PSJ0,ASJ6
$9%& 9%& GBC-( )-4
9%& 9%& 19%& JA,JB,KC,YA2,YD,IJA,IJB,IJC,
IYA, IYB,IYC
$9%& 9%& GBC-( )-4-1/2
9%& 9%& ——
M61,MB1,MC,MD4,X,
X1,X1M,XA,PSM0,NSM0,
ASM6,IMB,IMC,
IMD,IXA,IXB,
IXC,IXD
$9%& 9%& GBC-( )-6
9%& 9%& 19%& XB,XC,XD
$9%& 9%& GBC-( )-6-1/4
9%& 9%& ——
X7, X71,IXD7,MD7
MD74,XA7,XB7,XC7,XD7
$9%& 9%& GBC-( )-7
9%& 9%& ——
B2
——
SBC-( )-4
GSBC-( )-4
4SBC-( )-4
6SBC-( )-4
——
BB,FC,CA2,CD
ABC-( )-4-1/2
SBC-( )-4-1/2
GSBC-( )-4-1/2
4SBC-( )-4-1/2
6SBC-( )-4-1/2
——
P61,PB1,PC,PD,
EA,E,E1
ABC-( )-6
SBC-( )-6
GSBC-( )-6
4SBC-( )-6
6SBC-( )-6
——
EB,EC,ED
ABC-( )-6-1/4
SBC-( )-6-1/4
GSBC-( )-6-1/4
4SBC-( )-6-1/4
6SBC-( )-6-1/4
——
E7,E71,PD7,PD74,
EB7,EC7
ABC-( )-7
——
——
——
——
——
I6
ABC-( )-I6
——
——
——
——
——
I8
ABC-( )-I8
——
——
——
——
——
L1
$9%& /
——
——
——
——
——
D1
$9%& '
——
——
——
——
——
( ) = Insert Tray Width
864.234.4800
m p h u s k y. co m
139
Copyright 2013 MP Husky. All rights reserved.
CABLE TRAY
Reducing Splice Plates
Offset Splice Plates
for Concentric and
Eccentric Reductions
Reducing splice plates are used instead
of reducer fittings and offer better versatility and economy since they are less
expensive and do not require covers.
For concentric reductions, two plates
of equal offset are used. For eccentric
reductions, one plate is used along
with a standard splice connector, not
included. (Splice hardware is included)
Aluminum
HDGAF
Steel
Stainless
Steel
304
Stainless
Steel
316
Galvannealed
(Husky Way)
3-3/8”, 4”, 4-1/2”
ASP-HOR-( )
SSP-HOR-( )
4SP-HOR-( )
6SP-HOR-( )
NSP-HOR-( )
´ ´ ([FHSW,
ASP-XOR-( )
SSP-XOR-( )
4SP-XOR-( )
6SP-XOR-( )
NSP-XOR-( )
I6
ASP-I6OR-( )
--
--
--
--
´ ([FHSW,
ASP-L1OR-( )
SSP-L1OR-( )
4SP-L1OR-( )
6SP-L1OR-( )
NSP-L1OR-( )
I8
ASP-I8OR-( )
--
--
--
--
10”
ASP-D1OR-( ) SSP-D1OR-( )
4SP-D1OR-( )
6SP-D1OR-( )
NSP-D1OR-( )
( ) = Insert offset of plate in inches.
Copyright 2013 MP Husky. All rights reserved.
140
864.234.4800
m p h u s k y. co m
11-ACCESSORIES
Tray
Depth
CABLE TRAY
Splices and Connectors
Trough and Ladder to Single Channel Connectors For All Trays
These connectors take a single Channel off a Ladder or Trough sideways or downward.
(Hardware included)
Channel
Type
Alum.
HDGAF
SS
304
SS
316
Galvannealed
(Husky Way)
G4,G6
ACC-GU
SCC-GU
4CC-GU
6CC-GU
NCC-GU
Structural Connector For Ladders and Trough
Structural connectors terminate Ladder or Trough on top of concrete floors. Tray hardware is
included. Use 1/2” hardware at floor connection.
Alum.
HDGAF
SS
304
SS
316
Galvannealed
(Husky Way)
All Trays
ASC-U
SSC-U
4SC-U
6SC-U
NSC-U
11-ACCESSORIES
Channel
Type
Wall Penetration Sleeve
The wall penetration sleeve is a 24” long pan with wall flanges, cover & cover screws,
that allows tray to be connected on both sides of the wall. Gaskets and sealants (not
included), may be applied in the field.
(W)=insert Width
' LQVHUW'HSWK
Channel
Type
Alum.
MillGalv.
HDGAF
SS
304
SS
316
Galvannealed
(Husky Way)
All Trays
AWPS-(W)-(D)
PWPS-(W)-(D)
SWPS-(W)-(D)
4WPS-(W)-(D)
6WPS-(W)-(D)
NWPS-(W)-(D)
Hardware for Splice Connectors
Splice hardware is offered in standard zinc plated steel finish, or in 316 stainless steel to
withstand corrosive attack under many atmospheric conditions.
864.234.4800
m p h u s k y. co m
Hardware
Item
Plated
Steel
SS
316
´6SOLFH%ROW
B-100
B-100-6S
6SOLFH1XW
Washer Comb.
N-100
N-100-6S
141
Copyright 2013 MP Husky. All rights reserved.
CABLE TRAY
Splices and Connectors
Bonding Jumpers
Bonding jumpers are available to maintain electrical continuity across hinged and expansion splices. The aluminum jumpers are used with oxidation inhibitor under the contact
points. The short circuit rating is 600 Amperes. Hardware included. Sold as each.
Catalog Number
AFS-C
Bonding Jumper/Grounding Strap
Tin plated braided copper. 12” long hole to hole.
Hardware Included
Tray Type
Catalog Number
$)6&7 DPSV $:*
$)6&7 DPSV $)6&7 DPSV $)6&7 DPSV $)6&7 DPSV .&0,/
$OO7UD\V([FHSW
Husky Centray
$)6&7&5 DPSV $:*
Husky Centray
$)6&7&5 DPSV &HQWHU6SLQH :DOO0RXQW
$)6&7&5 DPSV Drill Jigs
Tray Depth
Catalog No.
3-3/8”
9'-
4”
JDJ
4-1/2”
KDJ
6”
MDJ
6-1/4”
XBDJ
7”
MDDJ
8”
L1DJ
10”
D1DJ
Note: These drill jigs are for C-Channel rails
and will not work on I-Beam type trays.
Oxidation Inhibitor
An oxidation inhibitor is used where permanent electrical continuity is important. For best results, clean connecting surfaces from dirt and oil by wiping clean and
removing oxide coating by abrasion once over with emery cloth. Apply a thin coat of oxidation inhibitor on the cleaned surfaces and make connection immediately. Each container of
compound is sufficient to effect approximately eighty splices.
Catalog Number
OI
$ERYHSDUWQXPEHUVDUHIRUHDFK
Copyright 2013 MP Husky. All rights reserved.
142
864.234.4800
m p h u s k y. co m
11-ACCESSORIES
Using drill jigs on field-cut ends ensures the proper alignment of holes, allowing full design
strength of the splice. A splice plate can also be clamped to the side rail and used as a template for a small quantity of field cuts.
CABLE TRAY
Accessories
End Dropout
This dropout is used at the end of a cable tray system, or to provide a smooth drop off for small cables
or any point between the rungs in the ladder system. It can be used in pairs, where dropping cable
from both directions, or singly, when dropping cable in one direction. Hardware Included.
Galvann.
Tray
Type
Alum.
MillGalv.
SS
304
SS
316
HDGAF
(Husky
Way)
JA,JB,MD4,XB,XC,IJA,
IJB,IJCMD7,MD74
$9' 69' 9' 9' *9' N/A
( )=insert width
Hardware included.
Part # is for 1 each.
MB1,M61,XA
$9' ;$
69' ;$
9' ;$
9' ;$
*9' ;$
N/A
HA,J2,MC,KC
$9' +$
69' +$
9' +$
9' +$
*9' +$
N/A
YA2,I8,IYA,IYB,IYC,IMB,
IMC,IMD,IXA,IXB,IXC,IXD7
$9' <$
69' <$
9' <$
9' <$
*9' <$
N/A
XD,YD,X,X1,X1M,X7,
X71,I6,XA,XB7,XC7,XD7
$9' ;
69' ;
9' ;
9' ;
*9' ;
N/A
All Electray & Husky Way
ABD-( )
SBD-( )
4BD-( )
6BD-( )
GBD-( )
NBD-( )
Conduit Side Type Dropouts
The conduit side type dropout is a bracket used to secure a conduit clamp (not included), to
the side rail of the tray, allowing cables to exit the tray into conduit drops to the equipment.
Tray Type
Zinc Plated
SS 304
SS 316
HDGAF
All Trays
9'68
9'68
9'68
*9'68
11-ACCESSORIES
Part # is for 1 ea.
Grounding Connectors
Type GC Connectors hold a single through cable and a tap cable while separating the
ground conductor from the cable tray surface. Note that the bolt head is mounted on
the inside wall of the cable tray to avoid damage to the cable insulation. Grounding
connectors may be used with aluminum or galvanized steel cable trays and aluminum
or copper conductors. When mounted horizontally, the bolt may be used to replace
one of the bolts in a splice plate, eliminating the need to drill the tray. When used on
aluminum conductors the cable must be scratch brushed and Oxidation Inhibitor (OI)
must be used on the cable and connector. Clamps are tin plated.
864.234.4800
m p h u s k y. co m
143
Conductor
Catalog No.
62/ STR (.162-.372 Dia)
GC-2525-CT
6RO STR (.258-.419 Dia)
GC-2626-CT
2/0 (STR),3/0, 4/0, 250KCMIL
(.414-.575 Dia)
GC-2929-CT
Copyright 2013 MP Husky. All rights reserved.
Accessories
CABLE TRAY
Grounding Clamps
Type GBM high copper alloy Clamps hold a single through cable directly on the cable
tray surface. One wrench installation and UL467 listed. Copper alloy cast body with
Durium bolts, nuts and washers.
GB style clamps have a back piece that separates the cable from the tray surface. GB
style not shown.
Conductor
GBM
Catalog No.
GB
Catalog No.
62/ 2/0 Str
GBM-26G3
GB-26G3
2/0 (SOL),3/0,4/0 & 250MCM
GBM-29G3
GB-29G3
300,350,400 & 500MCM
GBM-34G3
GB-34G3
550-750MCM
GBM-39G3
GB-39G3
These copper clamps are furnished in copper alloy, however tin plating is available as an option.
Ground Clamp for fastening ground wire to Cable Tray or Cable Bus. Clamp is tin plated
extruded aluminum with Zinc Electroplated Steel hardware. Use for aluminum or copper
conductors. Clamp has serrations to bite through insulating oxides on aluminum tray
and grip the tray. Screws tighten with 1/4” hex wrench.
Third Party Certification:
UL Listed E-24264
CSA Certified LR9795 (for copper conductors only)
Applicable Third Party standards:
UL Standard 467
CSA Standard C22.2 No. 41
NEC 250.77 and 392.6
Conductor
#6, #4, #3, #2, #1, 1/0, 2/0, 3/0, 4/0 AWG to 250KCMIL
Catalog No.
HP-CTGC
Double Grounding Clamp (NEW)
This zinc plated Double Grounding Clamp is used to clamp ground wire to the tray or
structure. The hole is 5/16”.
Cable Size
Catalog No.
Copyright 2013 MP Husky. All rights reserved.
5/16”
HCM-28
3/8”
HCM-29
1/2”
HCM-30
144
864.234.4800
m p h u s k y. co m
11-ACCESSORIES
Grounding Clamp (NEW)
CABLE TRAY
Accessories
Cable Separators / Divider Strips
Cable separators (divider strips) are available for all tray types in aluminum, HDGAF, millgalvanized, galvannealed and 304 or 316 stainless steel. Separators come in either 3”, 5”,
6” 7”, 8”, or 10” heights and are slotted at regular intervals for ease of installation without
field drilling. Each separator is furnished with all necessary splice clips and the required
number of nuts, bolts, and captive lock washers. Separator Rung Fasteners must be
ordered separately for attachment to Ladder rungs without drilling. One (CSS) separator
splice included with each.
Straight Lengths: Standard length is 10 or 12 feet. HDGAF will be provided in lengths
no longer than 72”. The grouping of slots is designed to fit the hole pattern of MP Husky
corrugated ventilated Troughs and Ladder Rungs.
For 10 ft lengths, change the –144
to –120 on the end of the part
number.
For 6 ft. lengths, use -72
For 5 ft. lengths, use -60
Sep
Hgt
Tray
Hgt
Alum.
MillGalv.
SS
304
SS
316
HDGAF
(Husky Way)
Galvann.
2-3/4”
3-3/8”-4-1/2”
A3S-144
S3S-144
43S-144
63S-144
G3S-72
N3S-144
4-3/4”
6”-6-1/4”
A5S-144
S5S-144
45S-144
65S-144
G5S-72
N5S-144
5-3/4”
7”
A6S-144
S6S-144
46S-144
66S-144
G6S-72
——
6-3/4”
8”
A7S-144
——
——
——
——
——
8-3/4”
10”
A9S-144
——
——
——
——
——
11-ACCESSORIES
Horizontal Bends: Standard length is 6 feet. Each piece is punched and slotted for easy
field adjustment to any degree of radius curvature. Sections may be field cut or continued
along a straight run. One (CSS) separator splice included with each.
Sep
Hgt
Alum.
MillGalv.
SS
304
SS
316
HDGAF
Galvannealed
(Husky Way)
2-3/4”
A3S-HA
S3S-HA
43S-HA
63S-HA
G3S-HA
N3S-HA
4-3/4”
A5S-HA
S5S-HA
45S-HA
65S-HA
G5S-HA
N5S-HA
5-3/4”
A6S-HA
S6S-HA
46S-HA
66S-HA
G6S-HA
——
6-3/4”
A7S-HA
——
——
——
——
——
8-3/4”
A9S-HA
——
——
——
——
——
For Vertical Bends: Vertical separators must be factory formed to the proper radius
needed. Vertical separators can be ordered to the degree of bend or the customer
can order all 90° separators and field cut them to the proper degree bends. One
(CSS) separator splice included with each.
7KHIROORZLQJLQIRUPDWLRQLVUHTXLUHGDWWKHWLPHRIRUGHU
1. Inside or outside bend
2. Type of material
3. Degree of bend
4. Radius of bend
5. Separator height
([DPSOH$99,
864.234.4800
m p h u s k y. co m
Sep
Hgt
Alum.
MillGalv.
SS
304
SS
316
HDGAF
Galvannealed
(Husky Way)
2-3/4”
$9 69 9 9 *9 19 4-3/4”
$9 69 9 9 *9 19 5-3/4”
$9 69 9 9 *9 ——
6-3/4”
$9 ——
——
——
——
——
8-3/4”
$9 ——
——
——
——
——
145
Copyright 2013 MP Husky. All rights reserved.
CABLE TRAY
Accessories
Separator Fasteners for
Ladders
Separator fasteners allow attachment of separators to Ladder rungs without drilling
the rungs (except I6 & I8). Order 4 per straight section, 3 per horizontal fitting and
2 per vertical fitting. Rung fasteners are stainless steel.
Part number is for one each.
Catalog Number
SSUSC-U
Separator Splice
Our CSS Separator Splice (sold separately) is applied to ensure a smooth transition
between barrier strips.
Catalog Number
CSS
End Plates
Blind end plates are available for all tray types and are furnished with mounting
hardware.
( ) = Insert Tray Width Hardware included.
Alum.
MillGalv.
SS
304
SS
316
HDGAF
(Husky Way)
3-3/8”
AEP-( )-3-3/8
SEP-( )-3-3/8
4EP-( )-3-3/8
6EP-( )-3-3/8
GEP-( )-3-3/8
NEP-( )-3-3/8
4”
AEP-( )-4
SEP-( )-4
4EP-( )-4
6EP-( )-4
GEP-( )-4
NEP-( )-4
4-1/2”
AEP-( )-4-1/2
SEP-( )-4-1/2
4EP-( )-4-1/2
6EP-( )-4-1/2
GEP-( )-4-1/2
——
6”, I6
AEP-( )-6
SEP-( )-6
4EP-( )-6
6EP-( )-6
GEP-( )-6
NEP-( )-6
6-1/4”
AEP-( )-6-1/4
SEP-( )-6-1/4
4EP-( )-6-1/4
6EP-( )-6-1/4
GEP-( )-6-1/4
——
7”
AEP-( )-7
SEP-( )-7
4EP-( )-7
6EP-( )-7
GEP-( )-7
——
8”, I8
AEP-( )-8
——
——
——
——
——
10”
AEP-( )-10
——
——
——
——
——
11-ACCESSORIES
Siderail
Heightt
Galvan.
Mini Trim
Mini trim can be used as a protective edging to protect cables from sharp surfaces that cables
may contact. Mini trim is a vinyl embossed extrusion with a segmented metal core that can
be cut with a knife between the metal core segments. It will grip edges from .010” to .050”
thick, and is supplied in 100 ft. and 250 ft. rolls in black.
Copyright 2013 MP Husky. All rights reserved.
Length
Catalog Number
IW
MINI TRIM-100
IW
MINI TRIM-250
146
864.234.4800
m p h u s k y. co m
CABLE TRAY
MP Husky Mid-Span Splice (NEW)
MP Husky’s Mid-Span Splice option provides the ability to
place a splice at any point within the support span without
diminishing the load rating of certain tray types based on an
installation of 3 spans or more. Requires some field drilling.
(Hardware Included)
Catalog Number
ASP-MS-( )
( ) = insert tray height
11-ACCESSORIES
NOTE: Please contact manufacturer for list of approved tray types
To ensure data available is most current, please visit www.MPHUSKY.com
864.234.4800
m p h u s k y. co m
147
Copyright 2013 MP Husky. All rights reserved.