Concealed closer series Product selection guide The concealed LCN closers feature a modern design for concealment in either the head frame or top rail of the door. This guide is based on the desired mounting of the closer. EXTERIOR DOOR CONCEALED IN TUBE FRAME CONCEALED IN FRAME DOUBLE LEVER ARM SINGLE LEVER ARM 2010 2210** 5010 SINGLE LEVER ARM 20306030 DOUBLE LEVER ARM 5030 INTERIOR DOOR CONCEALED IN FRAME DOUBLE LEVER ARM CONCEALED IN TUBE FRAME SINGLE LEVER ARM 2010 2210** 5010 DOUBLE LEVER ARM 5030 CONCEALED IN DOOR SINGLE LEVER ARM 20306030 DOUBLE LEVER ARM 3030 SINGLE LEVER ARM 3130 3130SE*** ** INDICATES HIGH SECURITY CLOSER, DOOR POSITION SWITCH OPTIONAL. REFER TO HIGH SECURITY SECTION OF THE CATALOG. *** INDICATES FIRE LIFE SAFETY CLOSER. REFER TO FIRE LIFE SAFETY SECTION. Product comparison This chart shows a basic comparison of LCN concealed closers. Refer to the specific closer chapter for complete details. N 180° 110° 180° 110° 180° 140° 3030 140° 3130 100° 180° 100° 5010 180° 100° 5030 95° 6030 AVAILABLE NOT AVAILABLE RE ST AN SI HA 2030 *ARM FUNCTION DA R GU D (S IN LA HO R (D GLE LD OU ) B -O PE LE) ARM ED ZE D AC CE S DE SIB LA ILI YE TY D AC TI ON CO NC E EX ALE PO D SE D CYLINDER ND ED AT W DE R CO AT FINISH PL IN PO DO TUB OR E 4˝ 3/ 1- FR IN IN CLOSER SERIES 2010 AM E CONCEALED MOUNTING 95° Closer available with less than 5.0 lbs. opening force on 36˝ door. * Maximum opening/hold-open point with standard template. See individual closer series for degrees of opening per installation. 1 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 Concealed closer series APPLICATIONS FINISHES n n Available in six standard or a wide selection of optional custom n n n LCN’s powder coat finishes surpass 100 hours of salt spray which is n n For installations where a higher level of corrosive resistance is n For aluminum, hollow metal, or wood doors and frames. Can be used with hinge or pivot mounted door. Closers for 4˝ or minimum 1-3/4˝ head frame or 4˝ top rail. Mounting clips for wood frames and other installation accessories available for unusual conditions. For concealed in door closers consult factory for installations with pivots. powder coat finishes to blend with door and frame. over four times the ANSI standard for corrosion resistance. FEATURES COMMON TO CONCEALED CLOSERS n n n n n n Mountings for head frame or door top rail. Handed for right or left swinging doors. (except 6030) Closers to meet ADA reduced opening force requirements. Adjustable hydraulic backcheck cushions opening swing prior to 90°. Separate regulation of general closing speed and latching speed. Joints in arm and shoe adapt to uneven trim. (for double lever arms) n required, LCN offers an optional special rust inhibiting (SRI) pretreatment. Closers that combine the exclusive LCN powder coat finish and the SRI pre-treatment exceed the ANSI standard for corrosion resistance even further. Plated finishes are available as an option to accent door and frame. (SRI not available with plated finishes) LISTINGS & APPROVALS UL listed for self-closing doors without hold-open under “SWINGING DOOR CLOSERS” (GVEV) file R 1943. Tested and certified under ANSI Standard A156.4. Consult factory for details. Consult factory for other listings such as; cUL, California State Fire Marshal, Bureau of Standards and Appeals. DESIGN ASSISTANCE LCN has been providing reliable solutions to unique door control problems since 1925. Design and specification assistance are only a phone call away. Contact LCN for assistance or technical information at 877-671-7011 or FAX 800-248-1460 (Order Entry), Fax 815-879-1495 for Product Support. POSITIVE PRESSURE LCN closers have been certified for three hours by UL to be in compliance with UL 10 C. Contact LCN for specific details on door closer fire ratings. WARRANTY 15 year limited warranty. See General Information Section for complete warranty details. FASTENERS Standard WOOD and MACHINE SCREW (WMS) pack contains phillips head wood and machine screws to install the closer. TORX machine screws are available for some closers. SPECIFICATIONS Refer to “SPECIFICATIONS”section for suggested architectural specifications. Note 1: Phillips head, metric machine screws are available, please specify. MAINTENANCE MATERIALS Closers mounted according to LCN installation instructions require no periodic maintenance or adjustments. (Closers concealed in the door or frame) n High strength cast iron cylinder. n Forged steel main arms (except 6030). n One piece forged steel piston. n A ll weather fluid in overhead concealed models performs to temperature ranges from 120°F (49°C) to -30°F (-35°C) without any seasonal adjustment. n High efficiency, full complement, low friction bearings. n Tamper resistant regulating screws. n Full rack and pinion hydraulic action. n Q uiet, low friction track and roller combination for all single lever (standard) arm closers. 2 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 2010 Series Features The concealed 2010 Series is a heavy duty closer designed to provide complete concealment. The single lever arm and roller assembly provide smooth, quiet door control and the choice of finishes and track functions meet virtually all architectural requirements. Grade 1 - ANSI A156.4, UL 10 C, ADA, 100 Hour Salt Spray, Meets BAA - Buy American Act Cast Iron Body Full Complement Bearing 1-1/2˝ Diameter Piston 11/16˝ Diameter Double Heat Treated Pinion Journal Mounting Concealed (in frame); aluminum frame requires minimum 4˝ x 4˝ (102 mm) tube Arms Standard arm and track Finishes/Colors/ Powder Coat Fluid All Weather Fluid Handing Handed n n n n n Size Sized 1-6 n Warranty 15 years Customized installation templates or products may be available to solve unusual applications. Contact LCN Product Support for assistance. E) OP BLE EN ) GL IN 110° Closer available with less than 5.0 lbs. opening force on 36˝ door. * Maximum opening/hold-open point with standard template. See individual closer series for degrees of opening per installation. 3 LCN Door Control Catalog phone: 877-671-7011 OU (S R D LA AR GU RE ND 180° AVAILABLE NOT AVAILABLE *ARM FUNCTION ST A DE AC ZE HA D ED CO R ED DE AT W ARM CE SS IB LA ILI YE TY D AC TI ON CO NC E EX ALE PO D SE D CYLINDER AT FINISH PL PO 4˝ DO TUB OR E IN IN 13/ FR AM E CONCEALED MOUNTING IN n Optional SRI primer - powder coat only Optional plated finishes ND Special Templates Aluminum (689) Statuary Bronze (690) Light Bronze (691) Black (693) Dark Bronze (695) Brass (696) Custom colors optional n n SI n LD - n n n Wood and Machine Screw Pack (D Body Construction Fasteners HO Certifications n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 2010 Series Mounting details Concealed Mounting 5-5/16" 135 mm 3-5/8" 92 mm 14" 356 mm 3/8" 10 mm 10" 254 mm 2-1/16" 52 mm 22-1/2" 572 mm 1" 25 mm 1-1/4" 32mm 1/4" 6mm Butt Hinges Should not exceed 5˝ (127 mm) in width Auxiliary Stop n to 1-1/16" 27 mm of Track of Closer Recommended where a door cannot swing 180° Optional track bumper assembly assists backcheck in cushioning the opening swing of the door (not intended to replace an auxiliary stop). n Top Rail 1-3/8" 35 mm 1-3/8˝ (35 mm) mortise required With Fire Shield, 1-13/32˝ (36 mm) mortise required n 5/16˝ (8 mm) cutout required at top of the door, stop face only n n Door Thickness 1-3/4˝ (44 mm) minimum Hollow Metal Frame Consult factory for installation instructions Maximum opening n Butt hinge template allows 180°, trim permitting Limited to 110° when optional bumper is installed n Adjustable hold-open points from 85° to 110°, with hold-open track n Offset pivot template allows 110°, trim permitting Limited to 95° when optional bumper is installed n Adjustable hold-open points from 75° to 95°, with hold-open track n n Center pivot template allows 120°, trim permitting Limited to 95° when optional bumper is installed n Adjustable hold-open points from 75° to 95°, with hold-open track n n Notes: • For interior or exterior doors • Single acting cylinder in head frame • Concealed arm and track in door top rail 4 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 2010 Series Accessories Cylinders Cylinder Arm Installation Accessories 2010-3077T Standard Arm 2010-420 Fire Shield 2011(3)(4)(5)(6)-3071 Cast Iron Cylinder Assembly Handed Handed n n nWith mounting plate n Standard 22 gauge steel liner mounts in the track mortise of the door’s top rail for 20 minute labeled wood doors n T rack roller not included with arm n 2010-169 Track Bumper Mounts in track to assist backcheck n Limits maximum opening n C onsists of bumper, bumper post, and mounting screw n NOTE: Track bumper does not replace auxiliary stop. Tracks 2010-3038 Standard Track 2010-3038B Standard Track with Bumper Non-handed n Non hold-open n 2010-3054 Hold-Open Clip Non-handed n M ounts in track to provide holdopen function n Non hold-open n Will accept hold-open clip and/or bumper assembly. H old-open point controlled by clip location n Will accept hold-open clip n n Optional n Non-handed n Will accept bumper assembly n n 2010-3034H Hold-Open Track Roller Non-handed n Optional n Quiet, low friction roller assembly S houlder dimension “X” = 1/16˝ (2mm) Optional n 5 LCN Door Control Catalog phone: 877-671-7011 n S houlder dimension “X” = 1/16˝ (2mm) n Requires 2010-3034H 2010-3038HB Hold-Open Track with Bumper n Quiet, low friction roller assembly n n Standard n 2010-3038H Hold-Open Track 2010-3034 Track Roller fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 2010 Series Ordering Information How-to-order 2010 Series closers Closer will be shipped with: - Standard cylinder with finish plate - Standard arm - Standard track - Wood and machine screw pack Table of sizes n Select closer based on width of door. n 2010 Series cylinders available in size 1, 3, 4, 5, or 6. n Closing power of all 2010 Series closers may be increased 15%. n Specify next higher size closer where strong drafts exist. Select cylinder size 2011 2013 2014 2015 2016 unless options listed below are selected. Select hand RH LH Specify finish Standard Powder Coat __________ Aluminum, Dark Bronze, Statuary, Light Bronze, Black, Brass. Closer options Tracks Standard with Bumper (BUMPER) Hold-open (H) Hold-open with Bumper (HBUMPER) Finishes Custom Powder Coat (RAL)_____________ Plated Finish, US ______________ SRI primer (use with powder coat finishes only) Installation accessories Fire Shield, 2010-420 Screw pack TORX Machine Screw (TORX) Special template ST- ________ Exterior (and Vestibule) door width 2013 2014 2015 2016 Interior door width 28˝ 30˝ 36˝ 42˝ 48˝ 28˝ 34˝ 38˝ 48˝ 54˝ 60˝ 711mm 762mm 914mm 1067mm 1219mm 711mm 864mm 965mm 1219mm 1372mm 1524mm size 3 size 4 size 5 size 6 2013 2014 2015 2016 Minimum door width size 3 size 4 size 5 size 6 Minimum door width Indicates recommended range of door width for closer size. Reduced opening force 2010 Series closers CAUTION ! Any manual door closer, including those certified by BHMA to conform to ANSI Standard A156.4, that is selected, installed and adjusted based on ADA or other reduced opening force requirements may not provide sufficient power to reliably close and latch a door. Refer to POWER OPERATORS section for information on systems that meet reduced opening force requirements without affecting closing power. * Maximum opening force. 6 ­DOOR WIDTH 36˝ 42˝ 48˝ 8.5* lbs. 2014 2014 2015 5.0* lbs. 2011 2011 2013 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 2030 Series Features The concealed 2030 Series PACER® is a heavy duty closer designed to fit in a narrow, minimum 1-3/4˝ aluminum transom. The single lever arm and roller assembly provide smooth, quiet door control and the choice of finishes and track functions meet virtually all architectural requirements. Grade 1 - ANSI A156.4, UL 10 C, ADA, 100 Hour Salt Spray, Meets BAA - Buy American Act Cast Iron Body Full Complement Bearing 1 1/8˝ Diameter Piston 11/16˝ Diameter Double Heat Treated Pinion Journal Fluid All Weather Fluid Handing Handed Size Sized 1-5 Warranty 15 years n n n n n Aluminum (689) Statuary Bronze (690) Light Bronze (691) Black (693) Dark Bronze (695) Brass (696) Custom colors optional n n E) E) GL BL PE N OU IN -O LD HO 110° Closer available with less than 5.0 lbs. opening force on 36˝ door. * Maximum opening/hold-open point with standard template. See individual closer series for degrees of opening per installation. 7 LCN Door Control Catalog phone: 877-671-7011 (D (S R RD LA DA GU AN 180° AVAILABLE NOT AVAILABLE AVAILABLE NOT AVAILABLE *ARM FUNCTION RE AC D ED CO R ED AT DE W ARM CE S DE SIB LA ILI YE TY D AC TI CO ON NC EA EX L PO ED SE D CYLINDER AT FINISH PL IN Finishes/Colors/ Powder Coat Customized installation templates or products may be available to solve unusual applications. Contact LCN Product Support for assistance. PO /4 ˝ DO TUB OR E M E 13 FR A IN Standard arm and track Optional SRI primer - powder coat only Optional plated finishes CONCEALED MOUNTING IN Arms n ZE Special Templates Wood and Machine Screw Pack Concealed (in tube); aluminum frame requires minimum 1-3/4˝ (44 mm) x 4˝ (102) mm) tube n ND n SI n n n HA Body Construction Fasteners Mounting ST Certifications n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 2030 Series Mounting details Concealed Mounting 5-13/16" 148 mm 10" 254 mm 1-1/4" 32 mm 1" 25 mm 3-23/32" 94 mm 21-7/8" 556 mm 22-1/2" 572 mm 1-1/16" 27 mm 1-5/8" 41 mm 1-3/8" 35 mm 9/64" 4 mm Butt Hinges Should not exceed 5˝ (127 mm) in width Auxiliary Stop n Recommended where a door cannot swing 180° Optional track bumper assembly assists backcheck in cushioning the opening swing of the door (not intended to replace an auxiliary stop). n Top Rail 1-3/8˝ (35 mm) mortise required With Fire Shield, 1-13/32˝ (36 mm) mortise required n 5/16˝ (8 mm) cutout required at top of the door, stop face only n n Door Thickness 1-3/4˝ (44 mm) minimum Hollow Metal Frame Consult factory for installation instructions Wood Frame Installation simplified by WOOD MOUNTING CLIP SET 2030-416 for center pivoted or 2030-417 for offset pivoted and butt hung installations. Consult factory for preparation details. Maximum opening Butt hinge template allows 180°, trim permitting Limited to 110° when optional bumper is installed n Adjustable hold-open points from 85° to 110°, with hold-open track n n Consult factory if door will be held open at 180° n Offset pivot template allows 115°, trim permitting. Limited to 95° when optional bumper is installed Hold-open point from 85°, with hold-open track n n Center pivot template allows 120°, trim permitting Limited to 100° when optional bumper is installed n Adjustable hold-open points from 85° to 100°, with hold-open track n n Notes: • For interior or exterior doors • Single acting cylinder in head frame • Concealed arm and track in door top rail 8 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 1460 Series 2030 Series Accessories Accessories Cylinders Cylinder Arm 2030-3077T Standard Arm 2031(2)(3)(4)(5)-3071 Cast Iron Cylinder Assembly Handed n With mounting plate n Handed n Track roller not included with arm n Standard n Cylinders Tracks 2030-3038B Standard Track with Bumper 2030-3038 Standard Track Non-handed n Non hold-open n n n Will accept hold-open clip and/or bumper assembly n 2030-3038H Hold-Open Track Non-handed n Non hold-open n Will accept hold-open clip n 2030-3038HB Hold-Open Track with Bumper Non-handed n Will accept bumper assembly n Non-handed Optional Optional n Optional n Standard n 9 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 2030 Series Accessories Installation Accessories 2030-420 Fire Shield 22 gauge steel liner mounts in the track mortise of the door’s top rail for 20 minute labeled wood doors n 2030-416 Wood Mounting Clip Set Simplifies mounting center pivoted 2030 closer in wood frame n Includes latch stile clip, hinge stile clip, and cover S implifies mounting offset pivoted or butt hung 2030 closer in wood frame n n F or use with Ives Series center pivots n Includes two clips M ounts in track to provide holdopen function n H old-open point controlled by clip location n n For use with offset pivots n NOTE: Track bumper does not replace auxiliary stop Consult factory for special template n Consult factory for special template M ounts in track to assist backcheck. Limits maximum opening. n C onsists of bumper, bumper post, and mounting screw n n 2030-3054 Hold-Open Clip 2030-169 Track Bumper 2030-417 Wood Mounting Clip Set 2030-3034H Hold-Open Track Roller 2030-3034 Track Roller Quiet, low friction roller assembly Quiet, low friction roller assembly n S houlder dimension “X” = 1/16˝ (2mm) n n n S houlder dimension “X” = 1/16˝ (2mm) R equires 2030-3034H Hold-Open Track Roller n 10 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 1460 Series 2030 Series Ordering Information How-to-order 2030 Series closers Closer will be shipped with: - Standard cylinder with mounting plate - Standard arm - Standard track - Wood and machine screw pack Specify finish Standard Powder Coat __________ Aluminum, Dark Bronze, Statuary, Light Bronze, Black, Brass Select cylinder size 2031 2032 2033 2034 2035 unless options listed below are selected. Select hand RH LH Closer options Tracks Standard with Bumper (BUMPER) Hold-open (H) Hold-open with Bumper (HBUMPER) Finishes Custom Powder Coat (RAL)_____________ Plated Finish, US ______________ SRI primer (use with powder coat finishes only) Installation accessories Fire Shield, 2030-420 Wood Clip Set, 2030-416 Wood Clip Set, 2030-417 Screw pack TORX Machine Screw (TORX) Special template ST- ________ Table of sizes n n n n Select closer based on width of door. 2030 Series cylinders available in size 1, 2, 3, 4, or 5. Closing power of all 2030 Series closers may be increased 35%. Specify next higher size closer where strong drafts exist Exterior (and Vestibule) door width 2033 2034 2035 Interior door width 28˝ 30˝ 36˝ 42˝ 28˝ 34˝ 38˝ 48˝ 54˝ 711mm 762mm 914mm 1067mm 711mm 864mm 965mm 1219mm 1372mm size 3 size 4 size 5 2032 2033 2034 2035 Minimum door width size 2 size 3 size 4 size 5 Minimum door width Indicates recommended range of door width for closer size. Reduced opening force 2030 Series closers CAUTION ! Any manual door closer, including those certified by BHMA to conform to ANSI Standard A156.4, that is selected, installed and adjusted based on ADA or other reduced opening force requirements may not provide sufficient power to reliably close and latch a door. Refer to POWER OPERATORS section for information on systems that meet reduced opening force requirements without affecting closing power. * Maximum opening force. ­DOOR WIDTH 36˝ 8.5* lbs. 5.0* lbs. phone: 877-671-7011 fax: 800-248-1460 n www.allegion.com/us 48˝ 2033 2033 2034 2031 2032 2032 11 LCN Door Control Catalog n 42˝ n 009426 rev. 2/16 Notes __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________ 12 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 3030 Series Features The concealed 3030 Series is designed to mount in a 1-3/4˝ interior door. The double lever arm provides superior door control and the choice of finishes and arm functions meet virtually all architectural requirements. Grade 1 - ANSI A156.4, UL 10 C, ADA, 100 Hour Salt Spray, Meets BAA - Buy American Act Cast Iron Body Full Complement Bearing 1 -1/8˝ Diameter Piston 1/2˝ Diameter Double Heat Treated Pinion Journal Fluid All Weather Fluid Handing Handed Size Sized 1-4 Warranty 15 years Aluminum (689) Statuary Bronze (690) Light Bronze (691) Black (693) Dark Bronze (695) Brass (696) Custom colors optional n Customized installation templates or products may be available to solve unusual applications. Contact LCN Product Support for assistance. GL HO LD -O P EN BL OU IN (D (S R RD LA DA E) *ARM FUNCTION E) ARM GU CYLINDER AN FINISH D PL ER C AT O ED AT PO W IN n n n n n n Optional SRI primer - powder coat only Optional plated finishes ˝ DO TUB OR E E 3/ 4 1- FR AM Regular arm Finishes/Colors/ Powder Coat n CONCEALED MOUNTING IN Arms n Special Templates IN Concealed (in door); consult factory for installations with pivots RE n Mounting ND SI ED ZE D AC CE S DE SIB LA ILI YE TY D AC TI CO ON NC EA EX L PO ED SE D n n n Wood Screws and Torx Security Screws (optional) HA Body Construction Fasteners ST Certifications 180° 140° AVAILABLE AVAILABLE NOT AVAILABLE NOT AVAILABLE Closer available with less than 5.0 lbs. opening force on 36˝ door. * Maximum opening/hold-open point with standard template. See individual closer series for degrees of opening per installation. 13 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 3030 Series Mounting details Concealed Mounting B 3/4" 19 mm 15/16" 24 mm 3" 76 mm 1-3/8" 35 mm A 2-11/16" 68 mm 5/16" 8 mm 8-3/4" 222 mm 11-3/4" 298 mm 3-3/4" 95 mm 4-7/8" 124 mm 1-1/2" 38 mm 8-3/4" 222 mm 1-1/4" dia. 32 mm 9/16" 14 mm 2-15/16" 75 mm 3-3/16" 81 mm C Butt Hinges Should not exceed 5˝ (127 mm) in width Auxiliary Stop Recommended at hold-open point or where a door cannot swing 180° Top Rail Minimum 4˝ (102 mm) required Door Thickness n 1-3/4˝ (44 mm) minimum Please consult the door manufacturer to assure that the door integrity and warranty is maintained after installing the 3030 Series door closer in a 1-3/4˝ thick wood door n Maximum opening Can be templated for 100°: A = 3-5/8˝ (92 mm) B = 10-1/4˝ (260 mm) 130°: A = 2-5/8˝ (67 mm) B = 9-1/4˝ (235 mm) 180°: A = 1-5/8˝ (41 mm) B = 8-1/4˝ (210 mm) Hold-open points up to maximum opening or 140°, whichever is less, with hold-open arm. n Arm clearance above door C = 1-1/4˝ (32 mm) minimum Notes: • For interior or exterior doors • Single acting cylinder in top rail of door • Exposed arm on hinge side of door 14 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 3030 Series Accessories Cylinder Arms 3031(2)(3)(4)-3071 Cast Iron Cylinder Assembly 3030-3049 Hold-open arm 3030-3077 Regular arm Handed Handed Non-handed n n n With mounting plate P rovides hold-open function, adjustable at elbow n n Standard n Optional n 15 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 3030 Series Ordering Information How-to-order 3030 Series closers Closer will be shipped with: - Standard cylinder with mounting bracket - Regular arm - Wood and machine screw pack Select cylinder size 3031 3032 3033 3034 unless options listed below are selected. Select hand RH LH Specify finish Standard Powder Coat __________ Aluminum, Dark Bronze, Statuary, Light Bronze, Black, Brass. Closer options Arm Hold-open (H) Screw pack TORX Machine Screw (TORX) Finishes Custom Powder Coat (RAL)___________ Plated Finish, US ______________ SRI primer (use with powder coat finishes only) Special template ST- ________ Table of sizes Select closer based on width of door 3030 Series cylinders available in size 1, 2, 3, or 4 n Closing power of all 3030 Series closers may be increased 15% n n Interior door width 24˝ 34˝ 38˝ 48˝ 610mm 864mm 965mm 1219mm 3032 3033 3034 size 2 size 3 size 4 Minimum door width Indicates recommended range of door width for closer size. Reduced opening force 3030 Series closers CAUTION ! Any manual door closer, including those certified by BHMA to conform to ANSI Standard A156.4, that is selected, installed and adjusted based on ADA or other reduced opening force requirements may not provide sufficient power to reliably close and latch a door. Refer to POWER OPERATORS section for information on systems that meet reduced opening force requirements without affecting closing power. ­DOOR WIDTH * Maximum opening force. 16 36˝ n fax: 800-248-1460 n 48˝ 8.5* lbs. N/A N/A N/A 5.0* lbs. 3031 3031 3032 LCN Door Control Catalog phone: 877-671-7011 42˝ www.allegion.com/us n 009426 rev. 2/16 3130 Series Features The concealed 3130 Series is designed to mount in a 1-3/4˝ interior door. The single lever arm and roller assembly provides complete concealment and the choice of finishes and track functions meet virtually all architectural requirements. Grade 1 - ANSI A156.4, UL 10 C, ADA, 100 Hour Salt Spray, Meets BAA - Buy American Act Cast Iron Body Full Complement Bearing 1-1/8˝ Diameter Piston 1/2˝ Diameter Double Heat Treated Pinion Journal Fluid All Weather Fluid Handing Handed Size Sized 1-3 Warranty 15 years n Aluminum (689) Statuary Bronze (690) Light Bronze (691) Black (693) Dark Bronze (695) Brass (696) Custom colors optional Customized installation templates or products may be available to solve unusual applications. Contact LCN Product Support for assistance. *ARM FUNCTION G (S IN RD R HO 100° Closer available with less than 5.0 lbs. opening force on 36˝ door. * Maximum opening/hold-open point with standard template. See individual closer series for degrees of opening per installation. 17 LCN Door Control Catalog phone: 877-671-7011 LA DA 140° AVAILABLE AVAILABLE NOT AVAILABLE NOT AVAILABLE LE ( LD DOU ) BL -O PE E) N ARM GU CYLINDER RE FINISH D PL ER C AT O ED AT IN PO W ˝ DO TUB OR E 3/ 4 E n n n n n n Optional SRI primer - powder coat only Optional plated finishes 1- FR AM Standard arm and track n CONCEALED MOUNTING IN Arms Finishes/Colors/ Powder Coat n Special Templates IN Concealed (in door); consult factory for installation with pivots AN n Mounting ND SI ED ZE D AC CE S DE SIB LA ILI YE TY D AC TI CO ON NC EA EX L PO ED SE D n n n Wood Screws and Torx Security Screws (optional) HA Body Construction Fasteners ST Certifications n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 3130 Series Mounting details Concealed Mounting 2" 50 mm 11-3/4" 298 mm 1-1/16" 27 mm 22-1/2" 572 mm 3/8" 10 mm 4-7/8" 124 mm 1-3/8" 35 mm 1-1/2" 38 mm 1-1/4" 32 mm 1-1/4" dia. 32 mm 5/8" 16 mm 8-3/4" 222 mm 3" 76 mm 3-1/4" 83 mm 4-3/8" 110 mm Butt Hinges Should not exceed 5˝ (127 mm) in width Auxiliary Stop n Recommended at hold-open point or where a door cannot swing 140° Optional track bumper assembly assists backcheck in cushioning the opening swing of the door. It is not intended to replace an auxiliary stop n Top Rail Minimum 4˝ (102 mm) required Door Thickness n 1-3/4˝ (44 mm) minimum. Please consult the door manufacturer to assure that the door integrity and warranty is maintained after installing the 3130 Series door closer in a 1-3/4˝ thick wood door n Door Width 2´2˝ (660 mm) minimum Maximum opening n Templating allows 140°, trim permitting. 100° with optional bumper installed Adjustable hold-open points from 85° to 100°, with hold-open track n Notes: • For interior doors • Single acting cylinder and standard arm in top rail of door • Concealed track in head frame • Consult factory for installations with pivots. 18 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 3130 Series Accessories Cylinder Arm 3131(2)(3)-3071 Cast Iron Cylinder Assembly 3130-3077T Standard Arm Handed n With mounting plate n Standard n Handed n Track roller not included with arm n Standard n Tracks 3130-3038B Standard Track with Bumper 3130-3038 Track Non-handed n Non hold-open n n n Will accept hold-open clip and/ or bumper assembly n 3130-3038H Hold-Open track Non-handed n Non hold-open n Will accept hold-open clip n 3130-3038HB Hold-Open Track with Bumper Non-handed n Non-handed Will accept bumper assembly n Optional Optional n Optional n Standard n Installation Accessories 3130-3054 Hold-Open Clip 3130-169 Track Bumper M ounts in track to assist backcheck, does not replace auxiliary stop n Limits maximum opening n C onsists of bumper, bumper post, and mounting screw n 3130-3034H Hold-Open Track Roller 3130-3034 Track Roller M ounts in track to provide holdopen function n H old-open point controlled by clip location n Quiet, low friction roller assembly n Shoulder dimension “X” = 1/8˝ (3mm) n Quiet, low friction roller assembly n Shoulder dimension “X” = 1/8˝ (3mm) n R equires 3130-3034H HoldOpen Track Roller n 19 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 3130 Series Ordering Information How-to-order 3130 Series closers Closer will be shipped with: - Standard cylinder with mounting bracket - Standard arm wtih finish plate - Standard track - Wood and machine screw pack Select cylinder size 3131 3132 3133 unless options listed below are selected. Select hand RH LH Specify finish Standard Powder Coat __________ Aluminum, Dark Bronze, Statuary, Light Bronze, Black, Brass. Closer options Track Standard with Bumper (BUMPER) Hold-open (H) Hold-open with Bumper (HBUMPER) Screw pack TORX Machine Screw (TORX) Special template ST- ________ Finishes Custom Powder Coat (RAL)___________ Plated Finish, US ______________ SRI primer (use with powder coat finishes only) Table of sizes Select closer based on width of door. 3130 Series cylinders available in size 1, 2, or 3. n Closing power of 3130 Series closers is not adjustable n n Interior door width 26˝ 34˝ 38˝ 660mm 864mm 965mm 3132 3133 size 2 size 3 Minimum door width Indicates recommended range of door width for closer size. Reduced opening force 3130 Series closers CAUTION ! Any manual door closer, including those certified by BHMA to conform to ANSI Standard A156.4, that is selected, installed and adjusted based on ADA or other reduced opening force requirements may not provide sufficient power to reliably close and latch a door. Refer to POWER OPERATORS section for information on systems that meet reduced opening force requirements without affecting closing power. * Maximum opening force. 20 ­DOOR WIDTH 36˝ 42˝ 8.5* lbs. N/A N/A N/A 5.0* lbs. 3131 3131 3132 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 48˝ 5010 Series Features The concealed 5010 Series is a heavy duty closer designed for institutional, high traffic, or other applications exposed to weather or abuse. The double lever arm provides superior door control and a choice of finishes, cylinder functions, and arm functions that meet virtually all architectural requirements. Grade 1 - ANSI A156.4, UL 10 C, ADA, 100 Hour Salt Spray, Meets BAA - Buy American Act Cast Iron Body Full Complement Bearing 1-1/8˝ Diameter Piston 11/16˝ Diameter Double Heat Treated Pinion Journal Fluid All Weather Fluid Handing Handed Size Sized 1-6 Warranty 15 years Regular Arm Finishes/Colors/ Powder Coat n n n n n Aluminum (689) Statuary Bronze (690) Light Bronze (691) Black (693) Dark Bronze (695) Brass (696) Custom colors optional n n E) BL PE N OU LD -O (D R HO LA GU AN DA RD (S IN GL E) *ARM FUNCTION RE LA DE D CE S AC ZE ARM SI BI L YE ITY D AC TI CO ON NC EA EX L PO ED SE D CYLINDER ED FINISH W D PL ER C AT O ED AT PO IN Arms Customized installation templates or products may be available to solve unusual applications. Contact LCN Product Support for assistance. 4˝ DO TUB OR E E 13/ FR AM Concealed (in frame); aluminum frame requires 4˝ (102 mm) x 4˝ tube Optional SRI primer - powder coat only Optional plated finishes CONCEALED MOUNTING IN Mounting n Special Templates IN Wood Screws and Torx Security Screws (optional) n ND n SI n n n HA Body Construction Fasteners ST Certifications 180° 100° AVAILABLE AVAILABLE NOT AVAILABLE NOT AVAILABLE Closer available with less than 5.0 lbs. opening force on 36˝ door. * Maximum opening/hold-open point with standard template. See individual closer series for degrees of opening per installation. 21 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 5010 Series Mounting details Concealed Mounting 7/8" 22 mm 14" 356 mm 3-5/8" 92 mm 3/8" 10 mm 2-1/16" 52 mm 11-1/2" 292 mm A 2-11/16" 68 mm B 3/4" 19 mm 3/4" 19 mm 2" MAX 51 mm Butt Hinges Should not exceed 6˝ (152 mm) in width Auxiliary Stop Recommended at hold-open point or where a door cannot swing 180° Top Rail Minimum 2-1/8˝ (54 mm) required Delay Action n Add suffix “DEL” to selected cylinder (eg. 5014 DEL) (not available with 5016 cylinder) Delays closing from maximum opening to approximately 70° n Delay time adjustable up to approximately 1 minute n Maximum opening Butt hung doors can be templated for 100°: A = 10-3/16˝ (259 mm) B = 12˝ (305 mm) 180°: A = 5-1/2˝ (140 mm) B = 7-5/16˝ (186 mm) trim permitting Hold-open points up to 100° only with hold-open arm Center pivot mounting restricts opening to 140° n Offset pivot mounting allows up to 180°, trim permitting n n Notes: • For interior or exterior doors • Single acting cylinder in head frame • Exposed arm on hinge side of door 22 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 2-1/8" 54 mm 5010 Series Accessories Cylinder Arms 5011(2)(3)(4)(5)(6)-3071 Cast Iron Cylinder Assembly Handed n 5010-3049 Hold-Open Arm 5010-3077 Regular Arm Non-handed Handed n n With mounting plate P rovides hold-open function for 100° Template, adjustment at elbow n n Standard n Optional n 23 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 5010 Series 2030 Series Ordering information How-to-order 5010 Series closers Closer will be shipped with: - Standard cylinder with finish plate - Standard arm - Regular arm - Wood and machine screw pack Select cylinder size 5011 5012 5013 5014 5015 5016 (DEL not available) unless options listed below are selected. Select hand RH LH Specify finish Standard Powder Coat __________ Aluminum, Dark Bronze, Statuary, Light Bronze, Black, Brass Closer options Screw pack TORX Machine Screw (TORX) Cylinder function Delayed Action (DEL) Arm Hold-Open (H) Finishes Custom Powder Coat (RAL)_____________ Plated Finish, US ______________ SRI primer (use with powder coat finishes only) Special template ST- ________ Table of sizes Select closer based on width of door Series cylinders available in size 1, 2, 3, 4, 5, or 6 Closing power of all 5010 Series closers may be increased 50% Specify next higher size closer where strong drafts exist Delayed action not available with 5016 cylinder n n n n n Exterior (and Vestibule) door width 5013 5014 5015 5016 Interior door width 24˝ 30˝ 36˝ 42˝ 48˝ 24˝ 34˝ 38˝ 48˝ 54˝ 60˝ 610mm 762mm 914mm 1067mm 1219mm 610mm 864mm 965mm 1219mm 1372mm 1524mm size 3 size 4 size 5 size 6 5012 5013 5014 5015 5016 Minimum door width size 2 size 3 size 4 size 5 size 6 Minimum door width Indicates recommended range of door width for closer size. Reduced opening force 5010 Series closers CAUTION ! Any manual door closer, including those certified by BHMA to conform to ANSI Standard A156.4, that is selected, installed and adjusted based on ADA or other reduced opening force requirements may not provide sufficient power to reliably close and latch a door. Refer to POWER OPERATORS section for information on systems that meet reduced opening force requirements without affecting closing power. * Maximum opening force. 24 ­DOOR WIDTH 36˝ 42˝ 48˝ 8.5* lbs. 5012 5013 5013 5.0* lbs. 5011 5011 5012 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 5030 Series Features The concealed 5030 Series PACER® is a heavy duty closer designed to fit in a narrow, minimum 1-3/4˝ aluminum transom. The double lever arm provides superior door control and the choice of finishes and arm functions meet virtually all architectural requirements. Grade 1 - ANSI A156.4, UL 10 C, ADA, 100 Hour Salt Spray, Meets BAA - Buy American Act Cast Iron Body Full Complement Bearing 1-1/8˝ Diameter Piston 11/16˝ Diameter Double Heat Treated Pinion Journal Fluid All Weather Fluid Handing Handed Size Sized 1; 3-6 Warranty 15 years n n n n n Aluminum (689) Statuary Bronze (690) Light Bronze (691) Black (693) Dark Bronze (695) Brass (696) Custom colors optional n n E) BL GL PE N IN OU (S LD -O (D R HO LA GU RE AN DA RD SI B LA CE S AC DE ED D *ARM FUNCTION E) ARM IL YE ITY D AC TI CO ON NC EA EX L PO ED SE D CYLINDER ZE PO IN Regular Arm Finishes/Colors/ Powder Coat FINISH W D PL ER C AT O ED AT ˝ DO TUB OR E E Arms Customized installation templates or products may be available to solve unusual applications. Contact LCN Product Support for assistance. /4 M 13 FR A Concealed (in tube); aluminum frame requires minimum 1-3/4˝ (44 mm) x 4-1/2˝ (114 mm) tube Optional SRI primer - powder coat only Optional plated finishes CONCEALED MOUNTING IN Mounting n Special Templates IN Wood Screws and Torx Security Screws (optional) n ND n SI n n n HA Body Construction Fasteners ST Certifications 180° 100° AVAILABLE AVAILABLE NOT AVAILABLE NOT AVAILABLE Closer available with less than 5.0 lbs. opening force on 36˝ door. * Maximum opening/hold-open point with standard template. See individual closer series for degrees of opening per installation. 25 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 5030 Series Mounting details Concealed Mounting A 1-5/8" 41 mm 3-23/32" 94 mm 21-7/8" 556 mm 11-1/4" 286 mm B 2-11/16" 68 mm 3/4" 19 mm 2-1/8" 54 mm 19/32" dia. 15 mm 3/4" MIN. 19 mm Butt Hinges Should not exceed 6˝ (152 mm) in width Auxiliary Stop Recommended at hold-open point or where the door cannot swing 180° Wood Frame n I nstallation simplified by WOOD MOUNTING CLIP SET 5030-416 for center pivoted or 5030-417 for offset pivoted and butt hung installations n Consult factory for preparation details Top Rail Minimum 2-1/8˝ (54 mm) required Door Thickness Maximum 1-3/4˝ (44 mm), for doors thicker than 1-3/4˝ consult factory Maximum opening Butt hung doors can be templated for 100°: A = 5-13/16˝ (148 mm) B = 11-13/16˝ (300 mm) 180°: A = 2-1/16˝ (52 mm) B = 8-1/16˝ (205 mm) trim permitting Hold-open points up to 100° only with hold-open arm Center pivot mounting restricts opening to 120°. Hold-open up to 120° with hold-open arm n Offset pivot mounting allows up to 115°, trim permitting. Hold-open up to 115° with hold-open arm n n Notes: • For interior or exterior doors • Single acting cylinder in head frame • Exposed arm on push side of door 26 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 5030 Series Accessories Cylinder Arms 5031(3)(4)(5)(6)-3071 Cast Iron Cylinder Assembly 5030-3049 Hold-Open Arm 5030-3077 Regular Arm Handed Non-handed n Handed n n With mounting plate P rovides hold-open function for 100° template, adjustable at elbow n n Standard n Optional n Installation Accessories 5030-417 Wood Mounting Clip Set 5030-416 Wood Mounting Clip Set Simplifies mounting center pivoted 5030 closer in wood frame n Includes latch stile clip, hinge stile clip, and cover. n F or use with Ives Series center pivots n Simplifies mounting offset pivoted or butt hung 5030 closer in wood frame. n Includes two clips. n For use with offset pivots. n Consult factory for special template. n Consult factory for special template n 27 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 5030 Series 2030 Series Ordering information How-to-order 5030 Series closers Closer will be shipped with: - Standard cylinder with mounting plate - Regular arm - Wood and machine screw pack Select cylinder size 5031 5033 5034 5035 5036 unless options listed below are selected. Select hand RH LH Specify finish Standard Powder Coat __________ Aluminum, Dark Bronze, Statuary, Light Bronze, Black, Brass Closer options Arm Hold-Open (H) Finishes Custom Powder Coat (RAL)_____________ Plated Finish, US ______________ SRI primer (use with powder coat finishes only) Installation accessories Wood Clip Set, 5030-416 Wood Clip Set, 5030-417 Screw pack TORX Machine Screw (TORX) Special template ST- ________ Table of sizes Select closer based on width of door 5030 Series cylinders available in size 1, 2, 3, 4, 5 or 6 Closing power of all 5030 Series closers may be increased 50% Specify next higher size closer where strong drafts exist n n n n Exterior (and Vestibule) door width 5033 5034 5035 5036 Interior door width 28˝ 30˝ 36˝ 42˝ 48˝ 28˝ 34˝ 38˝ 48˝ 54˝ 60˝ 711mm 762mm 914mm 1067mm 1219mm 711mm 864mm 965mm 1219mm 1372mm 1524mm size 3 size 4 size 5 size 6 5033 5034 5035 5036 Minimum door width size 3 size 4 size 5 size 6 Minimum door width Indicates recommended range of door width for closer size. Note: Minimum door width 28˝ (711 mm). Reduced opening force 5030 Series closers CAUTION ! Any manual door closer, including those certified by BHMA to conform to ANSI Standard A156.4, that is selected, installed and adjusted based on ADA or other reduced opening force requirements may not provide sufficient power to reliably close and latch a door. Refer to POWER OPERATORS section for information on systems that meet reduced opening force requirements without affecting closing power. * Maximum opening force. 28 ­DOOR WIDTH 36˝ 42˝ 8.5* lbs. 5033 5033 5033 5.0* lbs. 5031 5031 5033 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 48˝ 6030 Series Features The concealed 6030 Series PACER® is a heavy duty, double acting closer designed to fit in a narrow, minimum 1-3/4˝ header. The single lever arm and roller assembly provides smooth, quiet door control and the choice of finishes and track functions meet virtually all architectural requirements. Installation at left illustrated with center pivot set (not included). Certifications Grade 1 - ANSI A156.4, UL 10 C, ADA, 100 Hour Salt Spray, Meets BAA - Buy American Act Body Construction n n n Cast Iron Body Full Complement Bearing 1-1/8˝ Diameter Piston 11/16˝ Diameter Double Heat Treated Pinion Journal Fasteners Wood Screws and Torx Security Screws (optional) Mounting Concealed (in tube); double acting Arms Standard arm with track Finishes/Colors/ Powder Coat Fluid All Weather Fluid Handing Non-Handed n n n n n Size Sized 1-5 n n Warranty n n Optional SRI primer - powder coat only Optional plated finishes n 15 years Special Templates Customized installation templates or products may be available to solve unusual applications. Contact LCN Product Support for assistance. N ST 95° AVAILABLE NOT AVAILABLE AVAILABLE NOT AVAILABLE 95° Closer available with less than 5.0 lbs. opening force on 36˝ door. * Maximum opening/hold-open point with standard template. See individual closer series for degrees of opening per installation. 29 LCN Door Control Catalog phone: 877-671-7011 *ARM FUNCTION AN D RE ARD GU ( LA SIN HO R (D GLE LD OU ) B -O PE LE) ARM HA PO W CYLINDER ND SI ED ZE D AC CE S DE SIB LA ILI YE TY D AC TI CO ON NC EA EX L PO ED SE D FINISH D PL ER C AT O ED AT DO TUB OR E IN IN 13/ 4˝ FR AM E CONCEALED MOUNTING IN Aluminum (689) Statuary Bronze (690) Light Bronze (691) Black (693) Dark Bronze (695) Brass (696) Custom colors optional n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 6030 Series Mounting details Concealed Mounting 4-1/2" 115 mm 1-5/8" 41 mm 18-1/4" 464 mm 1-5/8" 41 mm 1" 25 mm 1/2" 13 mm of Door 5-1/4" 133 mm 1-7/16" 37 mm 22-1/2" 572 mm 3-23/32" 95 mm 23-5/8" 600 mm of Pivot 1-1/4" 32 mm Auxiliary Stop Recommended where a door cannot swing 95° Center Pivot Set Must be used but ordered separately Door Width 30˝ (762 mm) minimum with 1-3/4˝ (44 mm) pivot centers Top Rail n 1-7/16˝ (36 mm) mortise required 3/8˝ (10 mm) cutout required at top of the door, both sides. n Door Thickness 1-3/4˝ (44 mm) minimum Centering Adjustment Centering is provided by rotating the track roller to center the door in the opening. Wood Frame n Installation simplified by WOOD MOUNTING CLIP SET, 6030-416 Consult product support for special template n Maximum opening Center pivot template allows 95° Adjustable hold-open points from 85° to 95°, with hold-open track n n Notes: • For interior or exterior doors • Double acting cylinder in cased frame • Concealed arm and track in door top rail • Center pivots only 30 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 6030 Series Accessories Cylinder Arm 6031(2)(3)(4)(5)-3071 Cast Iron Cylinder Assembly Tracks 6030-3038B Standard Track with Bumper 6030-3077T Standard Arm Non-handed n With mounting plate n Standard n n n Non-handed n 5/16˝ (8 mm) thick arm n T rack roller not included with arm n 6030-3038HB Hold-Open Track with Bumper Non-handed n Non hold-open n Non-handed Optional Will accept hold-open clip n Standard n Installation Accessories Simplifies mounting closer in wood frame n Includes latch stile clip, hinge stile clip, and cover n F or use with Ives Series center pivots n Consult factory for special template n 6030-3054 Hold-Open Clip 6030-169 Track Bumper 6030-416 Wood Mounting Clip Set M ounts in track to assist backcheck M ounts in track to provide holdopen function n n Limits maximum opening n C onsists of bumper, bumper post, and mounting screw n n H old-open point controlled by clip location n NOTE: Track bumper does not replace auxiliary stop. 6030-3034 Track Roller Quiet, low friction roller assembly includes eccentric with 3/4˝ (19 mm) adjustment to center 36˝ (914 mm) door n R equires 6030-3034H HoldOpen Track Roller 6030-3034H Hold-Open Track Roller Hold-open roller n Quiet, low friction roller assembly n 31 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16 6030 Series 2030 Series Ordering information How-to-order 6030 Series closers Closer will be shipped with: - Standard cylinder with mounting plate - Standard arm - Standard track with bumper - Wood and machine screw pack Select cylinder size 6031 6032 6033 6034 6035 unless options listed below are selected. Specify finish Standard Powder Coat __________ Aluminum, Dark Bronze, Statuary, Light Bronze, Black, Brass Closer options Track Hold-open with Bumper (HBUMPER) Finishes Custom Powder Coat (RAL)_____________ Plated Finish, US ______________ SRI primer (use with powder coat finishes only) Installation accessories Wood Clip Set, 6030-416 Screw pack TORX Machine Screw (TORX) Special template ST- ________ Table of sizes n n n n Select closer based on width of door 6030 Series cylinders available in size 1, 2, 3, 4, or 5 Closing power of all 6030 Series closers may be increased 35% Specify next higher size closer where strong drafts exist Exterior (and Vestibule) door width Interior door width 30˝ 34˝ 36˝ 42˝ 30˝ 34˝ 38˝ 48˝ 54˝ 762mm 864mm 914mm 1067mm 762mm 864mm 965mm 1219mm 1372mm 6033 6034 6035 size 3 size 4 size 5 6032 6033 6034 6035 Minimum door width size 2 size 3 size 4 size 5 Minimum door width Indicates recommended range of door width for closer size. Note: Minimum door width 28˝ (711 mm). Reduced opening force 6030 Series closers CAUTION ! Any manual door closer, including those certified by BHMA to conform to ANSI Standard A156.4, that is selected, installed and adjusted based on ADA or other reduced opening force requirements may not provide sufficient power to reliably close and latch a door. Refer to POWER OPERATORS section for information on systems that meet reduced opening force requirements without affecting closing power. * Maximum opening force. 32 ­DOOR WIDTH 36˝ 42˝ 48˝ 8.5* lbs. 6033 6034 6035 5.0* lbs. 6031 6032 6032 LCN Door Control Catalog phone: 877-671-7011 n fax: 800-248-1460 n www.allegion.com/us n 009426 rev. 2/16