LNA, 0.1 to 40GHz Model: BZ‐00104000‐500827‐252525 Specifications (23 °C) Features • Noise Figure: 4.0 dB (typ) • Unconditionally Stable at all temperatures • Internally Regulated DC Voltage • 50 Ohm Matched Input/Output • Field Replaceable 2.92mm K connectors • Excellent Group Delay and Phase Linearity • 0.009 inches diameter RF In/Out feed through • Operating Temp. ‐40 C to +85 C • 3 Year Warranty Options • Optimized Performance over Selected Bandwidth • Internally DC Block Input (Output DC Block Standard) • Hermetically Sealed Package • Improved Gain Flatness • Improved IN and OUT VSWR • Gain and Phase matching • Lower Noise Figure **CAUTION: The amplifier input is DC-coupled but does not have low impedance to GROUND because of the requirement to extend BW down to 100MHz. Extreme caution must be exercised to avoid Electro-static Discharge (ESD) at the input center conductor. B&Z offers option -01 which protects the amplifier against low level ESD but connecting it directly to the output of an antenna (typical EMC application) exposes the amplifier center conductor via antenna, thereby increasing risk of ESD damage. It is the customer's responsibility to minimize Electro-static discharge (ESD) to both - the antenna and the amplifier connected to it. If the application does not require response below 8GHz, B&Z offers other models with inductive return to GND that can offer lower NF, improved Gain, better In/Out VSWR and more robust ESD handling capacity. Please call for further information. Parameter Frequency Range Noise Figure* Gain Gain Flatness (+/‐) P1 Output Power Input VSWR Output VSWR Operating Temperature Non‐Operating Temp Range RF Input Power (no‐damage) Humidity (non‐condensing) Voltage Current Input Impedance RF Connector Dimensions Min 0.1 ‐ 27 ‐ +8 ‐ ‐ ‐40 ‐65 ‐ ‐ +12 ‐ Typ Max ‐ 40 4.0 5.0 32 ‐ ±1.7 ±2.5 +10 ‐ ‐ 2.5:1 ‐ 2.5:1 ‐ +85 ‐ +85 ‐ +13 ‐ 95 +12 +15 175 50 2.92mm ‐ Female 29.9 x 18.7 x 7.6 Units GHz dB dB dB dBm °C °C dBm % VDC mA Ohms mm * Noise Source used for measurement from 0.1GHz to 40 GHz is HP346C-K01 . NF Uncertainty (approx. 0.3 dB). 0.2 dB due to ENR of HP 346C-K01; and 0.1 dB, due to the gain modulation of the unit, caused by the HP 346C-K01 source impedance change in the ON and OFF state. Noise Figures and other parameters degrade below 500 MHZ. Noise Figures at Cryogenic Temperatures not given due to uncertainty of measurement for very low values. Call to discuss. Typical Data Noise Figure S21 37 6.0 35 5.5 27 25 Min 23 12 4.0 Power (dBm) Noise Figure (dB) 29 14 Max 4.5 31 Gain (dB) 16 5.0 33 3.5 3.0 2.5 10 8 4 2 1.0 19 0.5 0 17 0.0 -2 0 10000 20000 30000 40000 0 10000 Frequency (MHz) 20000 30000 40000 0 0 80 -5 -5 60 -10 -10 40 -15 -15 -25 -30 -40 -30 -35 -35 -60 -40 -40 -80 -45 -45 -100 -50 20000 Frequency (MHz) 30000 40000 Max -20 -25 -20 40000 Return Loss (dB) Return Loss (dB) Max -20 0 30000 S22 0 20 20000 Frequency (MHz) S11 S21 Group Delay 10000 10000 Frequency (MHz) 100 0 Min 6 2.0 1.5 21 Group Delay (ps) Power Out @ 1dB Compression 18 -50 0 10000 20000 30000 40000 0 Frequency (MHz) B&Z Technologies • 25 Health Sciences Drive • Stony Brook • New York 11790 Phone: (631) 444‐8827 • Fax: (631) 444‐8825 • info@bnztech.com • www.bnztech.com 10000 20000 Frequency (MHz) 30000 40000 LNA, 0.1 to 40GHz Model: BZ‐00104000‐500827‐252525 .43 10.9 BIAS PIN Ø0.02 .26 6.5 .15 3.8 2X 2X 2X .38 9.5 .06 1.6 .30 7.6 2X .20 5.1 .37 9.4 .74 18.7 .61 15.5 GROUND CONNECTION .14 3.6 .28 7.1 2X O .07 1.9 MTG. HOLES 2X .19 4.7 Approx. Actual Size Mounting Drawing Drop In B&Z Technologies • 25 Health Sciences Drive • Stony Brook • New York 11790 Phone: (631) 444‐8827 • Fax: (631) 444‐8825 • info@bnztech.com • www.bnztech.com Rev: 3/19/2013 d4101