Current Transducer HXS 50-NP
I
PN
= 12.5 - 25 - 50 A
45001
R
L
R
OUT
C
L
V
C
I
C
I
PN
I
P
V
OUT
V
REF
Primary nominal r.m.s. current
Primary current measuring range
Analog output voltage @ I
P
I
P
= 0
Internal Reference 1) - Output voltage
Output load resistance
V
REF
Output impedance
V
REF
Load impedance
Output impedance
Max. output capacitive load
Supply voltage (± 5 %)
Current consumption @ V
C
= 5 V
±50
±150
V
REF
± (0.625· I
P
/ I
PN
) V
V
REF
± 0.0125
2.5 ± 0.025
V typ. 200
≥
200
≥
2
<
10
<
1
V
Ω k
Ω k
Ω
Ω
µF
5 V
22 mA
A
A
f
X
L
TCV
OUT
TCV
REF
Accuracy 2) @ I
PN
, T
A
= 25°C
Linearity 0 .. I
PN
.. 3 x I
PN
Thermal drift of V
OUT
@ I
P
= 0
Thermal drift of V
REF
TCV
OUT
/ V
REF
TC
G
Thermal drift of V
OUT
/ V
REF
Thermal drift of the gain
@ I
P
= 0
V
OM
Residual voltage @ I
P
= 0, after an overload of 3 x I
PN DC t t ra r
Reaction time @ 10 % of I
PN
Response time @ 90 % of I
PN di/dt di/dt accurately followed
Output noise (DC ..10 kHz)
(DC .. 1 MHz)
Frequency bandwidth (-3 dB) 3)
≤
±1
≤
±0.5
≤
±1
≤
±0.4
% of
% of
% of I
I
I
PN
PN
PN mV/K
≤
±0.01
≤
±0.2
%/K mV/K
≤
±0.05
% of reading/K
<±1
< 3
% of I
PN
µs
< 5
> 50
µs
A/µs
< 15
< 40
DC .. 50 m V p p m V p p kHz
T
A
T
S
Ambient operating temperature
Ambient storage temperature dCp Creepage distance dCl
CTI
Clearance distance
Comparative tracking index (Group I ) m
UL94 classification
Mass
Standards
- 40 .. + 85
- 40 .. + 85
> 5.5
> 5.5
°C
°C m m m m
V > 600
V0
10 g
EN 50178 (97-10-01)
•
Hall effect measuring principle
•
Multirange current transducer through PCB pattern lay-out
•
Galvanic isolation between primary and secondary circuit
•
Isolation test voltage 2500V
•
Low power consumption
•
Extremely low profile, 10mm
•
Single power supply +5V
•
Fixed offset & gain
•
Small size and space saving
•
Only one design for wide current ratings range
•
High immunity to external interference.
•
Internal & external reference
•
AC variable speed drives
•
Static converters for DC motor drives
•
Battery supplied applications
•
Uninterruptible Power Supplies
(UPS)
•
Switched Mode Power Supplies
(SMPS)
•
Power supplies for welding
applications.
All Data are given with a R
L
= 10 k
Ω
LEM reserves the right to carry out modifications on its transducers, in order to improve them, without previous notice.
LEM Components
050906/5
Page 1/3 www.lem.com

V b
V b
V d
V e
V w
Nominal Voltage with IEC 61010-1 standards and following conditions
- Single insulation
- Over voltage category III
- Pollution degree 2
- Heterogeneous field
Nominal Voltage with EN 50178 standards and following conditions
150
300
- Reinforced insulation
- Over voltage category III
- Pollution degree 2
- Heterogeneous field
R.m.s. voltage for AC isolation test, 50/60 Hz, 1 mn 2.5
R.m.s. voltage for partial discharge extinction @ 10pC > 1
Impulse withstand voltage 1.2/50µs 6
V r.m.s.
V r.m.s.
kV kV
kV
Notes : 1) It is possible to overdrive V
REF
with an external reference voltage between 2 - 2.8 V providing its ability to sink or source approximately
2.5 mA.
2) Excluding offset and hysteresis.
3) Small signal only to avoid excessive heatings of the magnetic core.
LEM reserves the right to carry out modifications on its transducers, in order to improve them, without previous notice.
LEM Components
050906/5
Page 2/3 www.lem.com

16.5
18.5
12
0.6
6.1
Ref
Out
GND
Vc
8
6
4
2
7
5
3
1
4-0.5*0.25
7.7
HXS 50-NP
14
5V
47nF
0V
4.7nF
Output
47nF
8-1.3d
+Vc
Vout
Vref.(IN/OUT)
0V
Ip
Number of primary turns
1
Primary current nominal maximum
I
PN
[A] I
P
[A]
50 150
2
4
25
12.5
75
37.5
Primary resistance
R
P
[m ohm]
Primary insertion inductance
L
P
[uF]
0.05
0.025
0.2
1
0.1
0.4
Recommended
PCB connections
IN 1 3 5 7
IN
2 4
1 3 5
6 8
7
OUT
IN
2 4
1 3 5
6 8
7
OUT
2 4 6 8 OUT
•
General tolerance ± 0.2 mm
•
Fastening & connection of primary jumper 8 pins Ø 1.3 mm
Recommended PCB hole
•
Fastening & connection of secondary
Ø 1.5 mm
4 pins 0.5 x 0.25
Recommended PCB hole Ø 0.7 mm
This transducer must be used in electric/electronic equipment with respect to applicable standards and safety requirements in accordance with the following manufacturer's operating instructions.
•
V
OUT
is positive when I
P
flows from terminals 1, 3, 5, 7 (IN) to terminals 2, 4, 6, 8 (OUT).
•
Temperature of the primary conductors should not exceed
100°C.
LEM reserves the right to carry out modifications on its transducers, in order to improve them, without previous notice.
LEM Components
Caution, risk of electrical shock
When operating the transducer, certain parts of the module can carry hazardous voltage (eg. primary busbar, power supply).
Ignoring this warning can lead to injury and/or cause serious damage.
This transducer is a built-in device, whose conducting parts must be inaccessible after installation.
A protective housing or additional shield could be used.
Main supply must be able to be disconnected.
050906/5
Page 3/3 www.lem.com