HA13151, HA13152 14 W × 4-Channel BTL Power IC ADE-207-116 1st. Edition Description The HA13151/HA13152 are high output and low distortion 4 ch BTL power IC designed for digital car audio. At 13.2 V to 4 Ω load, this power IC provides output power 14 W with 10% distortion. Functions • • • • 4 ch BTL power amplifiers Built-in standby circuit Built-in muting circuit Built-in protection circuit (surge, T.S.D, and ASO) Features • • • • Few external parts lead to compact set-area possibility Popping noise minimized Low output noise Built-in high reliability protection circuit HA13151, HA13152 Block Diagram Absolute Maximum Ratings (Ta = 25°C) Item 2 Symbol Rating Unit Remarks HA13151, HA13152 Operating supply voltage VCC 18 V VCC (DC) 26 V VCC (PEAK) 50 V I O (PEAK) 3 A Power dissipation* PT 83 W Junction temperature Tj 150 °C Operating temperature Topr –30 to +85 °C Storage temperature Tstg –55 to +125 °C 1 Supply voltage when no signal* 2 Peak supply voltage* 3 Output current* 4 Notes: 1. 2. 3. 4. Tolerance within 30 seconds Tolerance in surge pulse waveform Value per 1 channel Value when attached on the infinite heat sink plate at Ta = 25 °C. The derating carve is as shown in the graph below. 3 HA13151, HA13152 Electrical Characteristics (VCC = 13.2 V, f = 1 kHz, RL = 4 Ω, Rg = 600 Ω, Ta = 25°C) HA13151 Item Symbol Min Typ Max Unit Test Conditions Quiescent current I Q1 — 270 — mA Vin = 0 Output offset voltage ∆V Q –300 0 +300 mV Gain GV 30.5 32 33.5 dB Gain difference between channels ∆G V –1.5 0 +1.5 dB Rated output power Po — 14 — W VCC = 13.2 V THD = 10%, RL = 4 Ω Max output power Pomax — 22 — W VCC = 13.7 V THD = Max, RL = 4 Ω Total harmonic distortion T.H.D. — 0.05 — % Po = 3 W Output noise voltage WBN — 0.15 — mVrms Rg = 0 Ω BW = 20 to 20 kHz Ripple rejection SVR — 55 — dB Rg = 600 Ω, f = 120 Hz Channel cross talk C.T. — 70 — dB Rg = 600 Ω Vout = 0 dBm Input impedance Rin — 25 — kΩ Standby current I Q2 — — 200 µA Standby control voltage (high) VSTH 3.5 — VCC V Standby control voltage (low) VSTL 0 — 1.5 V Muting control voltage (high) VMH 3.5 — VCC V Muting control voltage (low) VML 0 — 1.5 V Muting attenuation ATTM — 70 — dB 4 Vout = 0 dBm HA13151, HA13152 HA13152 Item Symbol Min Typ Max Unit Test Conditions Quiescent current I Q1 — 270 — mA Vin = 0 Output offset voltage ∆V Q –300 0 +300 mV Gain GV 38.5 40 41.5 dB Gain difference between channels ∆G V –1.5 0 +1.5 dB Rated output power Po — 14 — W VCC = 13.2 V THD = 10%, RL = 4 Ω Max output power Pomax — 22 — W VCC = 13.7 V THD = Max, RL = 4 Ω Total harmonic distortion T.H.D. — 0.05 — % Po = 3% Output noise voltage WBN — 0.25 — mVrms Rg = 0 Ω BW = 20 to 20 kHz Ripple rejection SVR — 45 — dB Rg = 600 Ω, f = 120 Hz Channel cross talk C.T. — 60 — dB Rg = 600 Ω Vout = 0 dBm Input impedance Rin — 25 — kΩ Standby current I Q2 — — 200 µA Standby control voltage (high) VSTH 3.5 — VCC V Standby control voltage (low) VSTL 0 — 1.5 V Muting control voltage (high) VMH 3.5 — VCC V Muting control voltage (low) VML 0 — 1.5 V Muting attenuation ATTM — 60 — dB Vout = 0 dBm 5 HA13151, HA13152 Pin Explanation Pin No. Symbol Functions Input Impedance DC Voltage 1 IN1 CH1 INPUT 25 kΩ (Typ) 0V 11 IN2 CH2 INPUT 13 IN3 CH3 INPUT 23 IN4 CH4 INPUT 2 STBY Standby control 90 kΩ (at Trs. cutoff) — 3 OUT1 + CH1 OUTPUT — VCC/2 5 OUT1 – 7 OUT2 + 9 OUT2 – 15 OUT3 + 17 OUT3 – 19 OUT4 + 21 OUT4 – 10 MUTE 25 kΩ (Typ) — 6 CH2 OUTPUT CH3 OUTPUT CH4 OUTPUT Muting control Equivalence Circuit HA13151, HA13152 Pin Explanation (cont) Pin No. Symbol Functions Input Impedance DC Voltage 22 RIPPLE Bias stability — VCC/2 6 PVCC1 Power of output stage — VCC — 18 PVCC2 14 INVCC Power of input stage — VCC — 4 CH1 GND CH1 power GND — — — 8 CH2 GND CH2 power GND 16 CH3 GND CH3 power GND 20 CH4 GND CH4 power GND 12 IN GND Input signal GND — — — Equivalence Circuit 7 HA13151, HA13152 Point of Application Board Design 1. Notes on Application Board’s Pattern Design • For increasing stability, the connected line of VCC and OUTGND is better to be made wider and lower impedance. • For increasing stability, it is better to place the capacitor between VCC and GND (0.1 µF) close to IC. • For increasing stability, it is better to place C1 to C8 and R1 to R8, which are for stopping oscillation, close to IC. • It is better to place the grounding of resistor (Rg), between input line and ground, close to INGND (Pin 12) because if OUTGND is connected to the line between Rg and INGND, THD will become worse due to current from OUTGND. Figure 1 Notes on Application Board’s Pattern Design 8 HA13151, HA13152 2. How to Reduce the Popping Noise by Muting Circuit At normal operating circuit, Muting circuit operates at high speed under 1 µs. In case popping noise becomes a problem, it is possible to reduce the popping noise by connecting capacitor, which determines the switching time constant, between pin 10 and GND. (Following figure 2) We recommend value of capacitor greater then 1 µF. Also transitional popping noise can be reduced sharply by muting before VCC and Standby are ON/OFF. Figure 2 How to use Muting Circuit Table 1 Muting ON/OFF Time C (µF) ON Time OFF Time nothing under 1 µs under 1 µs 0.47 2 ms 2 ms 4.7 19 ms 19 ms 9 HA13151, HA13152 10 HA13151, HA13152 11 HA13151, HA13152 12 HA13151, HA13152 13 HA13151, HA13152 14 HA13151, HA13152 15 HA13151, HA13152 16 HA13151, HA13152 17 HA13151, HA13152 18 HA13151, HA13152 19 HA13151, HA13152 20 HA13151, HA13152 21 HA13151, HA13152 22 HA13151, HA13152 23 HA13151, HA13152 When using this document, keep the following in mind: 1. This document may, wholly or partially, be subject to change without notice. 2. All rights are reserved: No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without Hitachi’s permission. 3. Hitachi will not be held responsible for any damage to the user that may result from accidents or any other reasons during operation of the user’s unit according to this document. 4. Circuitry and other examples described herein are meant merely to indicate the characteristics and performance of Hitachi’s semiconductor products. Hitachi assumes no responsibility for any intellectual property claims or other problems that may result from applications based on the examples described herein. 5. No license is granted by implication or otherwise under any patents or other rights of any third party or Hitachi, Ltd. 6. MEDICAL APPLICATIONS: Hitachi’s products are not authorized for use in MEDICAL APPLICATIONS without the written consent of the appropriate officer of Hitachi’s sales company. Such use includes, but is not limited to, use in life support systems. Buyers of Hitachi’s products are requested to notify the relevant Hitachi sales offices when planning to use the products in MEDICAL APPLICATIONS. 24