Assembly Instructions for item : 2133
Connetix Series - Bar Pendant (Stem Version)
Important: Always disconnect the power before installing or replacing bulbs and before cleaning or other maintenance.
This light should be installed by a licensed electrician
Fig. 2
REMOVING THE CABLE SYSTEM
outlet box
1. Shut off power to the outlet box. (fig. 1)
2. Remove the mounting screws and the mounting plate.
Reserve the four mounting screws, two outlet box
screws, and three wire nuts. (Fig. 2)
3. Unscrew the wire nuts connecting the LED drivers to the fixture
power cord. Remove the LED drivers held by double-sided tape.
Reserve the four wire nuts and LED drivers. (Fig. 3)
4. Remove the cable stops by loosening the screws and sliding the
stops off of the cables. Remove the strain reliefs from the power
cords. Unscrew the hex nut with M10 wrench (exclude). Remove lock
washer and mounting plate. Reserve the mounting plate. (Fig. 4)
wire nut
mounting plate
outlet box screw
mounting screw
canopy
Fig. 1
Fig. 3
LED driver
wire nut
GRN
Fig. 4
D
mounting plate
strain relief
M10 wrench
GRN
D
1 of 4
hex nut
lock washer
cable stop
screw
©2012 SONNEMAN - A WAY OF LIGHT
Assembly Instructions for item : 2133
Connetix Series - Bar Pendant (Stem Version)
Important: Always disconnect the power before installing or replacing bulbs and before cleaning or other maintenance.
This light should be installed by a licensed electrician
Fig. 7
REMOVING THE CABLE SYSTEM
5. Loosen the set screws with Allen key and pull the power cords out
of canopy. Remove the steel cables from the canopy by pushing in the
lock and pulling the cables out of the canopy. (Fig. 5)
6. Loosen the Phillips screws, and remove the blocks. (Fig. 6)
7. Remove the steel cables. Unscrew the hex nuts using the M6 wrench
(exclude), and remove the lock washers and square plates. (Fig. 7)
8. Remove the square tubes. (Fig. 8)
9. Unscrew the hex nuts and threaded stems. (Fig. 9)
Reserve the hex nuts.
Fig. 5
power cord
M6 wrench
hex nut
lock washer
steel cable
square plate
Fig. 8
square tube
set screw
push
Allen key
steel cable
power cord
Fig. 6
Fig. 9
threaded stem
Phillips screw
block
hex nut
2 of 4
©2012 SONNEMAN - A WAY OF LIGHT
Assembly Instructions for item : 2133
Connetix Series - Bar Pendant (Stem Version)
Important: Always disconnect the power before installing or replacing bulbs and before cleaning or other maintenance.
This light should be installed by a licensed electrician
REMOVING THE CABLE SYSTEM
10. Check that all parts are reserved as shown in Fig.10.
Fig. 10
mounting plate
2x outlet box screw
from parts bag
4x mounting screw
paper tab
EVA sticker
7x wire nut
2 x LED driver
2 x hex nut
3 of 4
©2012 SONNEMAN - A WAY OF LIGHT
Assembly Instructions for item : 2133
Connetix Series - Bar Pendant (Stem Version)
Important: Always disconnect the power before installing or replacing bulb and before cleaning or other maintenance.
This light should be installed by a licensed electrician
LAMP INSTALLATION AND ASSEMBLY
11. Thread the hex nut 1/2” onto the threaded stem, then screw the threaded stem into
the block on the top of fixture.
12. Feed the cord through the square stem, corner hole on square block, square hole on
canopy, and corner hole on bracket.
13. Place the square block into the square stem, and secure with flat head screws.
14. Place the square stem onto the block on the top of the fixture, making sure the
corner holes are alligned.
15. Place the square block through the square hole on the canopy.
Left : Place the bracket, washer, ground wire washer, and lock washer on the
threaded stem, making sure the corner holes of the bracket and square block
are alligned. Secure with the hex nut using M6 the wrench (exclude).
Right : Place the ring on support cable, the bracket, lock washer on the
threaded stem, secure with the hex nut.
16. Connect the inner conductor of the fixture cord to the LED driver’s
“+” wire, connect the fixture’s “-” wire to the LED driver’s “-” wire
using wire nuts. The colors of the “+” and “-” wires are indicated on washer
the LED driver label.
17. Remove the papers tab from the center EVA stickers on the bottom of
the LED drivers (Fig. 10) and place the LED drivers inside the canopy,
against the side of the canopy without the mounting holes.
18. Attach the mounting plate to the outlet box, secure with outlet box screws.
19. Make appropriate electrical connections using wire nuts:
a. Connect the LED driver’s live wire (brown/black) to the live outlet box wire.
b. Connect the LED driver’s neutral wire (blue/white) to the neutral outlet
box wire.
c. Connect fixture’s ground wire (green or uncoated) to the ground outlet
box wire. If no ground is present in outlet box, connect fixture’s ground
wire to the mounting plate using the green screw (included).
d. Carefully place connections in outlet box.
20. Attach canopy to mounting plate, secure with mounting screws.
21. Restore power to the fixture.
outlet box
mounting plate
outlet box screw
support cable
ground wire’s washer
M6 wrench
hex nut
lock washer
bracket
mounting screw
canopy
flat head screw
square block
square stem
cord
threaded stem
hex nut
block
CARE INSTRUCTIONS
Dusting – Use a clean, dry cloth.
Cleaning – To protect the finish,
avoid any harsh abrasives or chemicals.
NOTE: This fixture is dimmable with Electronic Low Voltage
(Trailing-Edge) and Incandescent (Leading-Edge) type
dimmers. For best performance, we recommend Lutron
model CTELV-303P.
4 of 4
©2012 SONNEMAN - A WAY OF LIGHT