Part Number C156.065
Wiring Instructions
™
SC1-Gen2 Control by Draper
Caution
Electrical Specifications
➀ Make sure power is disconnected before installing controls.
➁ To Reduce the Risk Of Fire, Electric Shock, Or Injury To Persons, Installation
Work And Electrical Wiring Must Be Done By Qualified Person(s) In
Accordance With All Applicable Codes And Standards.
➂ To reduce the risk of fire and electric shock, install SC1-Gen2 only with listed
window shade operator(s) rated maximum 9.8 amps at 115VAC each.
➃ SC1-Gen2 is a line voltage control, designed to operate one motor. Activation
by low voltage input commands. If you want to switch two or more motors,
ISO relays must be installed in the circuit.
➄ SC1-Gen2 is electrically “hot” on the back of the circuit board. INS-SC1
(Draper Part Number C199.004) insulation board is provided.
Input:
E317985
Data:
+12VDC BUS Commands
3SMW
Low Voltage: Dry Contact—0v AC
Window
Shade
Control
Line Voltage: 115VAC 50Hz
Output:
½ HP, 115VAC 9.8 FLA.
Signal Output is Class 2.
Dimensions: 2½" W x 2¾" L x 7/8" H.
One SC1-Gen2 fits in a deep single gang J-Box.
Please Note: This device has not been evaluated for reliability to the Standard
for Tests for Safety-Related Controls Employing Solid-State Devices, UL 991
and therefore not considered suitable for entrapment protection.
Please Note: For low voltage wiring requirements, Draper recommends consulting with a professional low voltage electrical contractor. It is very important that
shielded and stranded CAT 5 cable be used to prevent any electrical interference.
Wiring Instructions for Controlling
One Shade with One SC1
To
115VAC
Motor
11
Ho 5VAC
Ne t (bla
utr ck
al ( )
wh
ite
)
Data BUS
"Aux" Port
Dry input terminals.
This can be any Single
Pole, Double Throw switch
(Torque dry input screw
terminals to 3 Lb-In.
Inserting wire into spring terminal
➀ Open spring terminal by inserting screwdriver into upper opening.
➁ Insert wire into lower opening.
➂ Remove screwdriver.
Ground
Note: Motor red and black wires will
need to “flip” if one motor is right
hand and the other is left hand.
Motor Neutral
-white
Black - Up
Red-Down
Data BUS
"Eye" Port
Fabric unrolling from back of
roller (standard)
Please Note: When connecting data "BUS," never link an "Eye" port to another "Eye" port. You may
link your BUS from "Eye" to "Aux" or "Aux" to "Aux."
All BUS command input devices must connect to an "Eye" port in order to power the input device.
Right hand motor
(Standard)
Black—Up
Red—Down
Wiring Instructions for Controlling Multiple Shades with One SC1
Please Note: This configuration
will limit SC1-Gen2 functions.
Left hand motor
en
To
115VAC
Motor 1
Gre
ISO
PU
ISO
IN
PU
T
Note:
Motor red and
black wires will
need to "flip" if one
motor is right hand
and the other is left hand.
Right hand motor
(Standard)
Red—Up
Black—Down
Interior
side
Left hand motor
IN
Data BUS
"Eye" Port
Fabric unrolling from front of
roller (reverse roll)
Earth
Ground
To
Additional
Motor
Green Wire
Green
T
Motor Neutral
-White
Black - Up
Red-Down
Black—Down
Red—Up
To
115VAC
Motor 2
Neu
tral
U
Dow p
n
Dry input terminals.
This can be any
Single Pole, Double
Throw switch (Torque
dry input screw
terminals to 3 Lb-In).
Neu
tral
U
Dow p
n
SC1
11
Ho 5VAC
Ne t (bla
utra ck)
l (w
hite
)
Data BUS
"Aux" Port
Interior
side
To
additional
ISOs
Red—Down
Black—Up
All connection wires must conform to the motor
manufacturer’s recommendation and prevailing
electrical codes. Use appropriate Class 2 wiring as
determined by location of use or install as required by
Article 725 of the NEC and local codes. USE COPPER
CONDUCTORS ONLY rated at 75° C or higher.
Please Note:
All input devices (low voltage LED switches, IR eye, RF receiver) which connect to the Eye jack must be connected using electrically straight 6-conductor
modular cable (RJ25). This means colors do not cross over: blue leads to blue, green to green, etc. (see diagram below)
PIN 6
CORRECT
Tab facing away (down)
BLUE
YELLOW
GREEN
RED
BLACK
WHITE
INCORRECT
PIN 1
WHITE
BLACK
RED
GREEN
YELLOW
BLUE
WHITE
BLACK
RED
GREEN
YELLOW
BLUE
PIN
6
Tab facing away (down)
PIN 1
Form SC1-Gen2_WD11
PIN 1
Tab facing away (down)
PIN 1
WHITE
BLACK
RED
GREEN
YELLOW
BLUE
Tab facing away (down) PIN 6
Six-Pin Layout
®
Copyright ©2011 Draper Inc.
PIN 6
COLOR
WHITE
BLA
L CK
RED
GREEN
YELLOW
BLUE
Printed in U.S.A.
PIN #
1
2
3
4
5
6
FUNCTION
R CLOCK
RQ
COMMON
+5VDC
5VDC
R DA
RQ
D TA
RP DA
D TA
+12VDC
12VDC
If you encounter any difficulties installing/wiring your IntelliFlex control, call your
dealer or Draper, Inc., Spiceland, Ind., (765) 987-7999; or fax (765) 987-7142.
Aux
Port
Aux
Port Eye
Port
To
Motor
Neutral
Red (Dir)
Black (Dir)
Eye
Port
Dry
Aux Contacts
Port
Eye
Port
Data cable
from Aux Port
to Eye port of
next SPGC4
To
Motor
Neutral
Red (Dir)
Black (Dir)
Dry
Contacts
Aux
Port
(765) 987-7999
www.draperinc.com
Dry
Contacts
To
Eye
Port
Neutral
AC (115/VAC)
To
Bla Moto
R e ck r
Ne d (D (Dir
ut ir) )
ral
To Switch,
splitter or
other input
device
To
Bla Moto
R e ck r
Ne d (D (Dir
ut ir) )
ral
Page 2 of 2
™ SC1-Gen2 Control by Draper