d:dicate™ 4006ER Omni Microphone, Rear cable
d:dicate™ 4006ES Omni Microphone, Side cable
A combination of the MMC4006 Microphone Capsule and the MMP-E
4006ER
d:dicate™
Omni
Rear d:dicate™
cable
4015C
Microphone
modular Compact
active
cable, Wide
this
micCardioid
isMicrophone,
part of the
modular
Recording
4006ES
d:dicate™
Sidenecessary
cable it is possible to
Microphone
series. At Omni
any timeMicrophone,
and with no tools
transform
theofbasic
4006E
Microphone
intothea MMP-E
new
configuration
bycable,
combinA
combination
of MMC4006
the
MMC4015
microphone
capsule
and active
the MMPA
combination
the
mic capsule
and
modular
ing 4006E
it withis another
Microphone
Preamplifier.
'TVIEQTPM½IV
the
part ofXLI'[MHIGEVHMSMHQMGMWTEVXSJXLIQSHYPEV
thed:dicate™
modular DPA
d:dicate™ Capsule
Recordingor
Microphones
series.
TMwith no tools necessary it is possible to transform the basic 4006E
At
any
time
and
series.
DPA
d:dicate
Suspension mount & windscreen
microphone into a new configuration by combining it with another DPA microphone
Suspend
the mic in the mount by securing the hook around the notch on the
capsule
or preamp.
PERFORMANCE
preamp. Subsequently twist the cable in the spiral-shaped end of the mount.
SUSPENSION
MOUNT
& WINDSCREEN
8LI
WYTTPMIH
GEPMFVEXMSR
GLEVX
WLS[W
XLI and
WTIGMEPP]
XEMPSVIH
This allows
theinMicrophone
hang in
ownaround
cable
be adjusted
Suspend
the mic
the mount byto
securing
theits
hook
the notch
the to any
MRHMZMHYEP
JVIUYIRG]
VIWTSRWI
SJ XLI
11'
GETWYPIon
QIEWYVIH
direction
by
bending
the
boom.
preamp.
Subsequently
twist
the
cable in the spiral-shaped end of the mount. This
[MXLEPMRIEV114%TVIEQT
own cable and be adjusted to any direction by
allows
the
microphone
to
hang
in
its
Mount the foam windscreen on the mic head whenever used outdoors or in
bending
the boom.
air turbulent
situations such as close miking voice in order to prevent wind
8]TMGEPSRERHSJJE\MWJVIUYIRG]VIWTSRWIWSJ11'EXGQ
or popthenoise.
Mount
foam windscreen on the mic head whenever used outdoors or in air tur(2 ft) situations
distance:such as close miking voice in order to prevent wind- or pop noise.
bulent
Grids
GRIDS
The4006E
d:dicate™
4006E
supplied
with
three
thatcharacterisare used to
The
is supplied
withisthree
different
grids
that different
are used togrids
change
change
of the microphone
extremely
careful
tics
of thecharacteristics
microphone acoustically.
Be extremely acoustically.
careful not toBe
touch
the exposed
not
to
touch
the
exposed
diaphragm
when
switching
grids.
Do
not
attempt
diaphragm when switching grids. Do not attempt to remove dust as it will not affect
to remove
dustofastheit microphone.
will not affect the performance of the Microphone.
the
performance
The pre-mounted silver near-field grid (DD0251) exhibits neutral frequency response
when used in near sound field (direct sound field).
CLIP
WINDSCREEN
The
black&diffuse-field
grid (DD0297) offers recording accuracy in diffuse sound
1SYRXXLIQMGMRXLIGPMTEXXLINYRGXMSRFIX[IIRQMGERH<06GSRRIGXSV
field
(far field) by compensating for the neutral high frequency loss caused by air
absorption.
1SYRXXLI[MRHWGVIIREXXLIQMGLIEHEJXIVLEZMRKTPYKKIHXSXLI<06
connector.
The silver trapezoid close-mic grid (DD0254) subtly rolls off the highest frequencies
to create smoother treble response when close miking sources with bright transient
[ [ [ H T E Q M G V S T L S R I W G S Q '
dpamicrophones.com / 4006E
w w w . d p a m i c r o p h o n e s . c o m / 4 0 0 6
CE marking
CE
marking
8LMWTVSHYGXGSRJSVQW[MXLEPPVIPIZERXHMVIGXMZIWETTVSZIHF]XLI)YVSTIER'SQQMWWMSR
This
product conforms to all relevant directives approved by the European Commision.
DPI-4006E-QG
Warranty
Warranty
4006E
is covered4006ER-4006ES
by five-year limited
warranty.
'MWGSZIVIHF]E½ZI]IEVPMQMXIH[EVVERX]
The
d:dicate™
Omni
Microphone, is covered by a five-year limited warranty.
DPI-4015C-QG
DPI-4006E-QG
Service
Service &
& repair
repair
If-J]SYEVIRSXWEXMW½IH[MXLXLIGLEVEGXIVMWXMGWI\LMFMXIHF]XLMWTVSHYGX
you are not satisfied with the characteristics exhibited by this product,
please go to
TPIEWIGSRXEGX]SYVRIEVIWX(4%
www.dpamicrophones.com/service
for instructions.
Microphones representative for support.
Specifications
Directional pattern
Omnidirectional
Principle of operation
Pressure
Cartridge type
Pre-polarized condenser
Frequency range
10 Hz - 20 kHz
Frequency range, ± 2 dB
20 Hz - 20 kHz
Sensitivity, nominal, ± 2 dB at 250 Hz
40 mV/Pa; -28 dB re. 1 V/Pa
Equivalent noise level, A-weighted
Typ. 15 dB(A) re. 20 μPa (max. 17 dB(A))
S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL)
Typ. 79 dB(A)
Total Harmonic Distortion (THD)
< 1 % up to 132 dB SPL peak
Dynamic range
Typ. 117 dB
Max. SPL, peak before clipping
132 dB
Output impedance
100 Ω
Minimum load impedance
2 kΩ
Cable drive capability
100 m (328 ft)
Output balance principle
Impedance balancing
Common Mode Rejection Ratio (CMRR)
> 40 dB
Power supply (for full specifications)
48 V Phantom power (±4 V)
Current consumption
3.5 mA
Connector
XLR-3M. Pin 1: shield, Pin 2: signal + phase, Pin 3: - phase
Color
Matte black
Weight
114g (4 oz)
Microphone diameter
16-19 mm (0.6 - 0.75 in)
Capsule diameter
16 mm (0.6 in)
Microphone length
35 mm (1.38 in)
Output voltage, RMS
2.2 V
Polarity
+V at Pin 2 for positive sound pressure
Temperature range
-40 to 45 °C (-40 to 113 °F)
Relative Humidity (RH)
Up to 90%