2216e DIN Rail Controller
Handbook Addendum
Specials Number EU0492
2216e DIN Rail Controller
Handbook Addendum
Specials Number EU0492
2216E DIN Rail Mounting Controller
MOUNTING DETAILS
CONTENTS
The controller can be mounted either on a flat surface or on DIN rail. For rail mounting use
symmetrical DIN rail 35 x 7.5mm or 35 x 15mm. For mounting on a flat surface use the (A) holes
provides. Use M4 screws tightened with a torque of 1Nm.
The dimensions are as follows:
(A)
(A)
133
•
INTRODUCTION
•
CONFIGURATION
•
ELECTRICAL CONNECTIONS
•
MOUNTING DETAILS
INTRODUCTION
This version of the 2216e controller is designed specifically for DIN rail or flat surface mounting. The
operation and performance is identical to that of the panel mounting 2216e - apart from the use of
external CJC compensation – see below. Please therefore, refer to the main handbook for
configuration and operation instructions.
The 2216e can be used as a temperature or process controller, independent alarm unit, or as an
isolating signal conditioner. It can operate standalone, or be connected to an operator panel,
Programmable Logic Controller or Supervisory Control System using Modbus or Devicenet
communications.
This version of the 2216e contains special firmware to measure the cold junction temperature at the
terminals of the DIN housing. A Pt100 sensor, mounted under the input terminals, is used to measure
the cold junction temperature.
(A)
(A)
Please note: because of the external CJC sensing, the Pt100 input is not supported.
CONFIGURATION
In configuration level external cold junction sensing must be selected. This is done in the O0 list by
selecting ?6 as the % reference temperature.
%
?6
The configuration and operation of this controller is otherwise identical to that of the standard 2216e
panel mounting controller.
Mounting
Part No: HA027439 Issue 1.0
ENG
Removing
Applies to controller s/w version A3.56
4
Part No: HA027439 Issue 1.0
Applies to controller s/w version A3.56
1
2216e DIN Rail Controller
Handbook Addendum
Specials Number EU0492
ELECTRICAL CONNECTIONS
2216e DIN Rail Controller
Handbook Addendum
Specials Number EU0492
ELECTRICAL CONNECTIONS - CONTINUED
The connections are as follows:
Input
Thermocouple
100 - 240Vac
1
2
Line Neutral
Outputs 1, 2 & 3
Output 1
Relay
3
4
Output
1
5
6
Output
2
7
3
+
+
10
+
4
-
-
Output 2
mA input
9
10
-
2216E
Relay
+
9
-
10
+
or
-
+
9
10
Part No: HA027439 Issue 1.0
+
6
-
12
13
14
15
Relay
0-10Vdc or
0-80mV
8
Devicenet
RS232 2-wire
17
Applies to controller s/w version A3.56
2
Contact
input
7
4-wire
11
Triac
Output 3
mV
Modbus
------ Digital Communications ------
Logic
5
2.49ohm
Volts
Sensor
Input
Triac
-
8
Output
3
Logic
9
RS485
CAN
Label
Color
Chip
11
--------- Not used ------------
11
V+
Red
---- Not used ----
Rx+
12
CAN_H
White
12
13
---- Not used ----
Rx-
13
SHIELD
None
14
--------- Common ------------
14
CAN_L
Blue
15
Rx
A(+)
Tx+
15
V-
Black
16
Tx
B(-)
Tx-
16
Not used
Not used
Part No: HA027439 Issue 1.0
Applies to controller s/w version A3.56
3