JSJS LW562 BC 3 Pack of CFR Bulbs with

advertisement
LightwaveRF
connect
Dimmable Energy Saving CFR
with Mood Remote
Operation Manual
Model No’s: JSJS LW560/561/562
It is important to install this product in accordance
with the fitting instructions below. Failure to do so
may render your guarantee void.
IMPORTANT: PLEASE RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE AND FOR GUIDANCE ON
THE ASSOCIATION OF REMOTE HANDSETS. FOR
HELP AND SETUP GUIDANCE PLEASE VISIT
www.lightwaverf.com
OVERVIEW:
Mood 3
Mood 2
Mood 1
All Off
On
Off
Channel
Selector
The LightwaveRF Connect CFR (Compact
Fluorescent Radio lamp) is a remotely operable,
dimmable, low energy light bulb. It is designed to
be a direct replacement for CFL light bulbs and
incandescent bulbs using standard fittings.
NOTE: The CFR is not designed to be used with any
mains dimmer switch inc. LightwaveRF dimmers.
FITTING INSTRUCTIONS:
IMPORTANT: Before commencing work, switch off
the power supply. Isolate the mains power supply or
switch off the circuit breaker in the consumer unit.
Install the CFR light bulb into lamp holder.
Reconnect the mains supply then switch ON the
light switch. The lamp will be at the brightest level.
To turn OFF, switch OFF the light switch.
NOTE: When first turned on the CFR will be at its
brightest. If after setting a dim level the light is then
switched off, the next time that the light is switched
on the light level will automatically return to the
previous setting.
SETUP:
Pairing with handheld Remote transmitters
The CFR can pair with up to 6 different remote
transmitters at any one time as it has a maximum of 6
memories.
1. Before any operation, the CFR must be turned ON to
operate correctly
2. The light switch must be turned OFF/ON 4 times
quickly (do not wait for the bulb to fully illuminate
each time) ending lastly at the ON position; the lamp
will start to slowly flash to illustrate it has entered
learning mode.
3. On a LightwaveRF Remote press the ‘ON’ button to
send the ‘ON’ command to the CFR.
IMPORTANT: On the Mood Remote (included in pack)
there is a slider labelled ABCD. Sliding between the
letters allows you to pair CFRs/other LightwaveRF
devices to separate channels (A,B,C or D). Which ever
position the slider is in when you pair the remote to
the CFR/other LightwaveRF device it will be paired to
THAT channel. You can then turn your CFRs/devices on
or off independently using the same set of on/off keys
with the slider in the relevant position. You can also
pair multiple devices to the SAME channel. Every
device that you pair to the remote will become part of
your mood selections (see ‘setting moods’) regardless
of which channel it is paired to.
4. The bulb will quickly flash a number of times to
confirm that the code is stored.
NOTE: If during learning mode no signal is received
the CFR will stop flashing after 20 seconds and exit
learning mode.
On
NOTE: To operate the CFR bulb with a remote control,
make sure the light switch is turned ON. If the light is
switched OFF by a remote control, remember the wall
switch remains at ON status; so next time switching
ON with the wall switch remember to switch from
OFF to ON.
Un-pairing remotes and clearing the CFR memory
Removing single device:
1. Before any operation, the light switch must be
turned ON to operate correctly.
2. Switch the light switch OFF/ON 4 times quickly (do
not wait for the bulb to fully illuminate each time)
ending lastly at the ON position; the lamp will start
to slow flash to illustrate it has entered learning
mode.
3. On the remote press the ‘OFF’ button to send the
OFF command to the CFR.
4. The bulbs will quickly flash a number of times to
confirm single code is deleted.
Off
Clearing Memory (will remove all paired remotes):
1. Before any operation, the light switch must be
turned ON to operate correctly.
2. Switch the light switch OFF/ON 4 times quickly (do
not wait for the bulb to fully illuminate each time)
ending lastly at the ON position; the lamp will start
to slow flash to illustrate it has entered learning
mode.
3. Switch the light switch OFF/ON another 4 times
quickly (do not wait for the bulb to fully illuminate
each time) ending last at ON position; lamp will
quickly flash to confirm all memorized codes are
deleted.
NOTE: If the RF distance between the transmitter and
receiver is too great to achieve reliable operation, the
LightwaveRF Connect SIGNAL BOOSTER may be
used in conjunction with this product to increase the
signal strength over greater distances.
OPERATION:
Using the existing light Switch
Switch ON/OFF by operating the light switch.
Dimming:
1. Ensure the CFR is ON. Switch the light switch OFF
and then ON quickly. Dimming will automatically
start.
2. To stop at the desired dim level switch the light
switch OFF then ON once.
NOTE: If no action is taken dimming will automatically
stop after 4 cycles and the brightness will return to
the previous level.
Using a LightwaveRF remote control
Make sure that the wall switch is turned ON first.
Switch ‘ON/OFF’
IMPORTANT: There is one set of ON/OFF buttons on
the Mood Remote provided (as indicated on previous
diagrams). However, by sliding the slider switch below
the on-off buttons to position A,B,C or D, the on and
off buttons can be treated as separate on-off buttons
for 4 separate devices. Which device is selected
depends on which position the slider is in (i.e. on-off
device ‘A’, on-off device ‘B’ and so on).
• Press the ‘ON’ Button once to switch paired devices
on.
• Press the ‘OFF’ Button once to switch paired devices
off.
• Press the ‘ALL OFF’ Button once to switch off all
paired bulbs.
Dimming down
1. Make sure the light is switched on.
2. Hold down the ‘OFF’ button on the remote.
3. After 1 second the light will start to dim down.
4. At the desired brightness level release the ‘OFF’
button.
NOTE: If the ‘OFF’ button is not released, the light will
continue to dim until no light is emitted and stop,
although the switch remains on, illustrated by the
illuminated blue LED.
Raising Dim Level
1. Make sure the light is switched on.
2. Hold down the ‘ON’ button on the remote.
3. After 1 second the light will start to become
brighter.
4. At the desired brightness release the ‘ON’ button.
NOTE: If the ‘ON’ button is not released, the light
level will increase until it stops at the maximum
possible level of brightness.
SPECIFICATION:
Power: 20W
RF frequency: 433.92 MHz
Input voltage: 220-240VAC
Power Factor: > 0.9
Luminous: 1200 lm
Current consumption: 90mA
Colour: 2700 K
Ra: 81
Dimming range: 5%~100%
Life time: 12,000 hours.
Birmingham Science Park Aston
Faraday Wharf
Holt Street
Birmingham
B7 4BB
Tel: 01902 500 562
Email: support@jsjsdesigns.com
Setting Moods Using the Mood Remote
1. Ensure that LightwaveRF devices (CFRs /dimmers/
sockets etc.) that you wish to include in the ‘mood’ are
paired with the Mood Remote (they can be paired to
any channel - A,B,C or D).
2. Using the Remote, or via manual control, set the
status (on or off ) and dim level of the devices that you
want to include in the mood.
3. When you are satisfied with the current setup,
press and hold one of the Mood buttons. The LEDs
on any devices paired with the Mood Remote will
flash to indicate that the Mood is now set.
4. Press the ‘All Off’ Button to turn off the mood. To
return to the saved mood at any time simply press the
relevant mood button once again.
5. Repeat the process for other mood buttons to
create multiple mood settings.
Download