35806WHT120D-C
PACKAGE CONTENTS
PART
A
B
C
D
E
F
G
DESCRIPTION
Cabinet light
Xenon units with Type G-8 20 W 120V bulbs
Cord
Plug
3 foot extension cord
4 foot cord with sockets
3 level touch dimmer
QTY
6
6
6
6
2
1
1
WARNINGS AND CAUTIONS
WARNING: • Review important safety instructions before installation
CAUTION : • Risk of exposure to excessive ultraviolet (UV) radiation.
• Do not operate without complete bulb enclosure in place or if lens is damaged
• Prior to installation , plug your cabinet light into an available electrical outlet in order to ensure that one or more of the
bulbs have not vibrated loose during shipping.
IMPORTANT SAFETY INSTRUCTIONS
This light is equipped with a polarized attachment plug (a plug having one blade wider than the other). This plug will fit in a polarized outlet only one
way. This is a safety feature. If you are unable to insert the plug fully into the outlet, reverse the plug. If it still will not fit, contact a qualified electrician.
Never use with an extension cord unless the plug can be fully inserted. Do not attempt to alter the safety purpose of the polarized plug.
CAUTION – To prevent electrical shock do not use this (POLARIZED) plug with an extension cord receptacle or other outlet
unless the blades can be fully inserted.
UNDER CABINET ONLY – MINIMUM
SPACING 12" ON CENTRE
CAUTION:
Lighted Lamp is hot!
BULB REPLACEMENT
USE A G-8 TYPE XENON
20 W 120 V BULB
TO REMOVE LENS COVER,
TURN COUNTERCLOCKWISE
USE A SOFT CLOTH WHEN HANDLING THE BULB
(OIL FROM SKIN MAY DAMAGE BULB.)
TO REPLACE LENS COVER, TURN
CLOCKWISE UNTIL COVER IS SECURED.
WARNING – To reduce the risk of FIRE, ELECTRIC SHOCK, EXPOSURE TO EXCESSIVE UV RADIATION, OR INJURY TO PERSONS:
1. Turn off/unplug and allow to cool before replacing bulb.
2. Bulb gets hot quickly! Contact only swich/plug when turning on.
3. Do not touch hot lens, guard, or enclosure.
4. Do not remain near light if skin feels warm.
5. Do not look directly at lighted bulb.
6. Keep lamp away from materials that may burn.
7. Use only with a G-8 type 20 W 120 V xenon bulb.
8. Do not touch the bulb at any time. Use a soft cloth. Oil from skin may damage bulb.
9. Do not operate the lamp with a missing or damaged lens; lens acts as guard/shield and UV light filter.
10. This lamp is intended to be used as an under cabinet light.
11. Avoid contact with the cord or combustibles such as plastic, paper goods, etc. with the hot bulb, bulb holder or reflector.
12. During installation, position cabinet light with respect to the cabinet-walls, so as to permit reading of the lamp replacement marking.
13. This cabinet light is not intended for illumination of aquariums.
14. This cabinet light is not intended for installation in plastic cabinets.
15. The instructions (item 2 above) provided on the enclosed adhesive back should be attached to cabinet.
16. Injury to persons and damage to the lamp and/or mounting surface may result if the lamp is pulled from the surface. To reduce the likelihood of
such injury or damage, mount only on a wood or particle board surface that is mechanically sound.
17. During installation, route and secure cord so as to avoid the likelihood of the cord contacting the cabinet light.
18. When replacing the bulb, lens cover is to be turned and removed; then follow BULB INSERTION AND REPLACEMENT directions for removing bulb.
19. Use only insulation staples or plastic ties to secure cord.
20. Route and secure cords so that they will not be pinched or damaged when the cabinet is pushed to the wall.
21. Not intended for recessed installation in ceilings.
PREPARATION:
Before beginning assembly, installation or operation of product, make sure all parts are present. Compare parts with package contents list and
diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
• Estimated assembly time: 30 minutes
•Tools required for assembly (not included):
•Flathead Screwdriver
•Star-head Screwdriver
•Safety Glasses
•Drill
•1/16" Drill Bit
•Hammer
•Soft Cloth
ASSEMBLY AND INSTALLATION INSTRUCTIONS
SURFACE MOUNTING
1. Locate desired position for the cabinet light.
2. Remove the lens cover from housing by rotating counterclockwise.
3. Route the wire through surface can notch, or if desired, drill a hole through the mounting surface and route wires through hole. Be sure to position the
surface can so the notch faces the rear of the cabinet.
4. Make sure there is no contact between the hot bulb, or reflector, and any combustible material such as plastic or paper goods, or the wire insulation.
5. Mount surface can and housing assembly with the three wood screws provided (tools not supplied).
6. Replace lens cover by rotating clockwise.
7. Route unit’s wire to “WIRE PLUG”.
CAUTION: DO NOT ROUTE WIRES AND EXTENSION CORDS THROUGH WALLS. USE FOR
EXTERNAL CABINET APPICATIONS ONLY.
8. Not intended for permanent hardwire installation inside built-in furnishings or trophy cases.
9. Do not conceal power supply cord (or power supply) inside a wall, ceiling, soffit, or permanent structure, and do not run the power supply cord
through holes in walls, ceiling, or floors.
10. If wire plug cover is still attached to plug, slide cover off by pushing away from plug. (See Illustration 1 )
11. Insert trimmed end of cord into plug pocket nearest the polarized blade (wide blade). Be sure that the ribbed side of cord goes over the right piercing
point and smooth side of cord goes over left piercing point. (See Illustration 2 )
12. Slide plug cover back onto wire plug (Illustration 3 ), and route plug to nearest outlet.
13. It will take about 30 minutes to finalize assembly.
RECESSED MOUNTING
CAUTION: RISK OF FIRE, Perform recessed installation only where top of cabinet light housing is not enclosed.
1. Drill a 2-1/8" hole in the desired location.
2. Remove the lens cover from housing by rotating counterclockwise.
3. Do not use surface can for recessed applications.
4. Feed wires through hole and push light housing into hole. Make sure there is no contact between the hot, bulb-holder, or
reflector, and the wire or any combustible material such as plastic or paper goods. Secure the light supply leads to avoid the
likelihood of the leads contacting the light. Use the three wood screws to fasten the housing in place (tools not supplied).
5. Replace lens cover by rotating clockwise.
6. Route unit’s wire to “WIRE PLUG”,
CAUTION: DO NOT ROUTE WIRES AND EXTENSION CORDS THROUGH
WALLS. USE FOR EXTERNAL CABINET APPLICATIONS ONLY.
7. If wire plug cover is still attached to plug, slide cover off by pushing away from plug. (See Illustration 1)
8. Not intended for permanent hardwire installation inside built-in furnishings or trophy cases.
9. Do not conceal power supply cord (or power supply) inside a wall, ceiling, soffit, or permanent structure.
Do not run the power supply cord through holes in walls, ceiling, or floors.
10. Insert trimmed end of cord into plug pocket nearest the polarized blade (wide blade). Be sure that the ribbed side of cord goes over the right piercing
point and smooth side of cord goes over left piercing point. (See Illustration 2)
11. Slide plug cover back onto wire plug (Illustration 3), and route plug to nearest outlet.
12. It will take about 30 minutes to finalize assembly.
TROUBLESHOOTING
RROBLEM
POSSIBLE CAUSE
One or more bulbs fail
to light
Vibration during shipping
SOLUTION
A. Unplug unit
B. Remove lens cover by rotating counterclockwise.
C. Refit bulb pins snugly into socket holders using a
tissue or cloth.(Oil from the skin may damage bulb.)
D. Replace lens cover by aligning tabs on cover with flat areas
on reflector then turn clockwise until cover locks into place.
ONE-YEAR LIMITED WARRANTY
The manufacturer warrants this product to be free from defects in workmanship and material present at time of shipment from the factory for one year
from the date of purchase. This warranty applies only to the original purchaser. The manufacturer agrees to correct such defect at no charge or at our
option replace the product with a comparable or superior model.
Any damage to the product by accident, misuse or improper installation, or by affixing accessories not produced by the manufacturer, is the purchaser’s
responsibility. The manufacturer assumes no responsibility whatsoever for product installation during the warranty period.
There is no further expressed warranty. The manufacturer disclaims any and all implied warranties. The manufacturer shall not be liable for incidental,
consequential or special damages arising at or in connection with product use or performance except as may otherwise be accorded by law. This
warranty gives you specific legal rights and you may also have other rights which vary from province to province. This warranty supersedes all prior
warranties.
Imported By: CANARM LTD., 2157 Parkedale Ave., Brockville Ontario,K6V 5V6,
Tel: (613) 342-5424, FAX: (613) 342-8437