Wiring diagram LINEARdrive 720D
(LIN720D2)
Other connectors:
VDC and LED connectors:
1
AWG 24-16
0.2-1.5 mm 2
{
12 -48VDC IN
-
+
LED groups
AWG 20-16
0.5-1.5 mm 2
1
2
2
9 mm
0.35 inch
Ext in +
Ext in -
9 mm
0.35 inch
R
R
R
R
TC
DMX in +
DMX in DMX in shield
Group 1
Group 1 GND
DA +
DA DA +
DA DMX in +
DMX in DMX in shield
LedSync out +
LedSync out LedSync shield
Group 2
Ext in Ext in +
DA +
DA DA +
DA -
Power
supply
Group 2 GND
LINEARdrive 720D
12-28V / 24W Direct voltage controlled LED driver
Group 3
Group 3 GND
Group 4
M
Group 4 GND
LedSync out +
LedSync out LedSync shield
CAUTION: The device may only be connected and installed by a qualified electrician. All applicable regulations, legislation and building codes must be observed. Incorrect installation of the device can cause irreparable damage to the device and the connected LEDs.
12V - 48V DC IN
DMX in/LedSync out
To connect the driver to a 12-48V DC power supply unit (PSU),
Use these connectors when the driver is used in a DMX net-
connect the PSU’s positive voltage supply wire to the VDC+
work.
connector and the PSU’s negative voltage supply wire to the
For DMX in, connect the network cable’s DMX+, DMX- and
VDC- connector. The driver and LEDs can use the same PSU.
DMX shielding wire (the orange/white, orange and brown wire
in a CAT5 cable) to the DMX in+, DMX in- and DMX in shield
EXT in
You have the possibility to connect an external control device
(0-10V control device, 10kΩ potentiometer or show selection
switch) to the driver’s Ext in+ and Ext in- connector. Configure
the driver for use with an external control device over the
3-button user interface.
connector respectively.
For LedSync out, connect the network cable’s data+, dataand shielding wire to the LedSync out+, LedSync out- and
LedSync shield connector respectively.
LED groups
Indicates the location of the connectors for your LED groups.
DA+ / DAUse these connectors to connect the driver to a DALI network.
Always combine a DA+ and a DA- connector for either data input or data output.
R(ed) represents channel 1, G(reen) represents channel 2,
B(lue) represents channel 3 and W(hite) represents channel 4.
The default group color allocation can be changed over the
3-button user interface.
© 2011 eldoLED. All rights reserved. V1.0
More product documentation and eldoLED’s terms and conditions are available at www.eldoled.com.
Wiring diagram LINEARdrive 720D
(LIN720D2)
32A
PSU
18A
Connecting an RGB LED strip
-
Maximum current per output: 6A
+
18A
Use a star connection for the ground wires and keep the
length of the wires that deal with high amperages under
10 - 15cm / 3.9 - 5.9 inch.
6A
6A
6A
6A
TC
RGB LED strip
Group 1
Group 1 GND
+
R
G
B
6A
Group 2
Group 2 GND
6A
Group 3
Group 3 GND
Configuration of the LED groups:
Group 4
Group 4 GND
Press M and + simultaneously, in the LED menu choose
RGB and save this setting by pressing M.
32A
PSU
Connecting an RGB strip and a white LED strip
24A
24A
Maximum current per output: 6A
-
Use a star connection for the ground wires and keep the
6A
6A
+
18A
6A
6A
6A
6A
TC
length of the wires that deal with high amperages under
RGB LED strip
Group 1
Group 1 GND
+
R
G
B
6A
Group 2
10 - 15cm / 3.9 - 5.9 inch.
Group 2 GND
6A
Group 3
Group 3 GND
Configuration of the LED groups:
White LED strip
6A
+
Group 4
Group 4 GND
-
Press M and + simultaneously, in the LED menu
choose RGBW and save this setting by pressing M.
Connecting warm white and cool white LED strips
24A
Maximum current per output: 6A
32A
PSU
-
Use a star connection for the ground wires and keep the
length of the wires that deal with high amperages under
6A
6A
6A
+
6A
6A
6A
6A
6A
6A
TC
Warm White LED strip
+
Group 1
Group 1 GND
6A
Group 2
10 - 15cm / 3.9 - 5.9 inch.
24A
Group 2 GND
Cool White LED strip
+
6A
Group 3
-
Group 3 GND
Configuration of the LED groups:
6A
Warm White LED strip
Group 4
+
Group 4 GND
Press M and + simultaneously, in the LED menu
-
Cool White LED strip
choose 4-4L and save this setting by pressing M.
+
-
Connecting four white or self-colored LED strips
24A
Maximum current per output: 6A
32A
PSU
-
Use a star connection for the ground wires and keep the
length of the wires that deal with high amperages under
10 - 15cm / 3.9 - 5.9 inch.
6A
6A
6A
TC
24A
+
6A
6A
6A
6A
6A
Group 1
Group 1 GND
Group 2
Group 2 GND
White LED strip
6A
+
-
6A
6A
White LED strip
+
Group 3
Group 3 GND
Configuration of the LED groups:
Press M and + simultaneously, in the LED menu
choose 1-4L and save this setting by pressing M.
6A
White LED strip
Group 4
+
Group 4 GND
-
White LED strip
+
-
eldoLED Europe bv
eldoLED America, Inc.
Luchthavenweg 18a
1762 Technology Drive # 226
5657 EB Eindhoven
San Jose, CA95110
The Netherlands T +31 40 2054050
USA
T +1 408 451 9333
F +31 40 2054058
F +1 408 451 9335
info@eldoled.com
nasales@eldoled.com