BEEDSPEED CONVERSION WIRING HARNESS LAMBRETTA

advertisement
BEEDSPEED CONVERSION WIRING HARNESS
LAMBRETTA VARITRONIC ELECTRONIC CONVERSION SERIES 2 and 3
OPTIONAL
FRONT BRAKE
LIGHT SWITCH FACILITY
REMOVER COVERS
IF REQUIRED.
PINK
12 VOLT AC LIGHTING with DC AUXILIARIES
Optional Facilities for Inside Legshield Toolbox and Front Brake Light Switch.
Spare wire from the top to the rear for Additional instruments.
BROWN
REAR LIGHT UNIT
BLACK
BLACK ( REAR LIGHT SUPPLY )
COLOUR CODED:
CONNECT COLOUR
TO COLOUR FROM
IGNITION SWITCH
/ LIGHT SWITCH.
BRAKE LIGHT SWITCH
BROWN (AC POWER )
PINK
BROWN
GREEN ( IGNITION CUT OUT )
HEADLIGHT
JUNCTION BOX
PINK
BROWN
BLUE/WHITE
BLUE/WHITE - SPARE WIRE FROM TOP TO BOTTOM ( AC/DC revs counter / fuel gauge? )
RED/WHITE DC
RED/WHITE DC POWER SUPPLY TO HEADSET AREA
WHITE FROM
HORN BUTTON
BLACK
EARTH
OPTIONAL INSIDE LEGSHIELD TOOLBOX.
REMOVE THE CAPS FROM THE
RED/WHITE - BLUE/WHITE AND GREEN
WIRES IF REQUIRED.
_
LIGHTING REGULATOR BOX
/ BATTERY CHARGER.
12 V BATTERY
+
REGULATOR BOX CONNECTIONS: Left to Right
TERMINAL 3 ( LIGHTS SUPPLY ). STATOR PLATE YELLOW/WHITE
( or plain YELLOW ) AND MAIN WIRING LOOM BROWN.
TERMINAL 2 - BLACK ( EARTH ).
TERMINAL 4 - STATOR PLATE RED/WHITE ( or plain RED ).
TERMINAL B+ - RED - FOR BATTERY CHARGING - TOO THE
BATTERY AND THEN RUN DC ITEMS FROM THE BATTERY.
RED
BROWN
BROWN (POWER SUPPLY TO LIGHTS/BRAKE LIGHT/HORN)
YELLOW / WHITE
HORN
RED/WHITE
BEEDSPEED PRODUCE A SEPARATE RANGE OF BATTERY
CHARGING TYPE WIRING HARNESSES TO RUN
DC INSTRUMENTS / ADD ON’S AND EXTRA SPOT LAMPS etc.
CONTACT [email protected] or visit BEEDSPEED.COM
+44 (0)1472 722222
GREEN
ELECTRONIC HT COIL
OPTIONAL INSIDE LEGSHIELD TOOLBOX.
RED/WHITE - DC SUPPLY FOR
INSTRUMENTS / SPOT LAMPS.
BLUE/WHITE - SPARE WIRE.
GREEN - REVS COUNTER.
BLACK / RED
BLUE
1
2
CDI
TERMINAL 1: GREEN and BLACK/RED ( LIVE )
TERMINAL 2: BLUE ( EARTH )
ALAN BEED
EARTH
STATOR PLATE
TO SET THE IGNITION TIMING :
BOLT THE STATOR PLATE DOWN IN THE CENTER OF ITS ADJUSTMENT SLOTS AND FIT THE FLYWHEEL.
WHILE THE PISTON IS AT TOP DEAD CENTER (TDC), PAINT A WHITE MARK ACROSS THE FLYWHEEL AND THE
MAG FLANGE AT ANY POINT THAT IS EASY TO VIEW, THIS IS NOW THE "TDC" MARK. TURN THE FLYWHEEL
BACK ANTI CLOCKWISE THE REQUIRED AMOUNT OF DEGREES BEFORE TOP DEAD CENTRE (23 Check
Instructions).
THEN MAKE ANOTHER MARK ON THE MAG FLANGE IN LINE WITH THE TDC WHITE MARK ON THE
FLYWHEEL, THIS IS NOW THE "TIMING" MARK AND THIS IS THE POINT WHERE THE SPARK SHOULD
OCCUR AT LOW RPM.
CHECK THAT THE IGNITION TIMING IS CORRECT USING A STROBE LIGHT. THE WHITE MARK ON THE
FLYWHEEL SHOULD CLEARLY LINE UP WITH THE WHITE TIMING MARK ON THE MAG FLANGE AT LOW
RPM. IF NOT THEN ADJUST THE STATOR PLATE AS NECESSARY.
BEEDSPEED.COM
Tel: +44 (0) 1472 722222
[email protected]
www.beedspeed.com
Download