International O-Ring Standard Cross Reference AS 568 BS 1806 ISO 3601-1 DIN 3771 NF T 47-501 JIS B2401 BS 4518 SMS 1586 ISO 6149 Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com International O-Ring Standard Cross Reference Shortly after O-Rings first came into common use, it became obvious that standards for O-Ring sizes, tolerances, and groove design would be beneficial. The first standards were issued in 1942. Since then various government and engineering organizations have produced a multitude of O-Ring standards. From this large list we chose to include the following national and international O-Ring standards in the cross reference tables presented in the following pages: AS568 BS 1806 ISO 3601 DIN 3771 BS 4518 JIS B 2401 NF T47-501 SMS 1586 ISO 6149 All of these standards specify acceptable tolerance ranges, while some call out quality and/or material requirements. The O-Rings in this cross reference are presented without regard to any materials or tolerances specified in the actual standards. We chose to list all sizes from each standard whether or not PAI has current tooling. Short descriptions of each standard follow including any designation for tolerances, quality and material. A sample Part Number appears in brackets at the end of each description, which are presented below in the order that they appear in our tables. AS 568 is produced by the Society of Automotive Engineers AS (Aerospace Standard) 568 describes 379 O-Rings including tolerances for Cross Section (C/S) and Inside Diameter (ID). The five main cross section groups are designed to be used in standard nominal inch applications. O-Rings are identified by - (dash) numbers with the first number (0-5) of each group matching up to a nominal inch cross section. An additional group is designed for use as tube fitting boss seals. The dash numbers for these tube & boss O-Rings begin with a 9. [ AS 568 - 123 ] BS 1806 is issued by the British Standards Institution. This standard includes all of the 5 main cross section groups in AS 568 plus extended sizes in the 1/4" nominal cross section group. Additional extended sizes were included in earlier versions of this specification, but were later eliminated. We chose to include them in this document since they are still in use. [ BS 1806 - 123 ] ISO 3601-1 is authored by the International Organization for Standardization. This document contains two groups of O-Rings. The first group, designated for General Industrial applications are "inch" sizes that for the most part match up exactly to the AS 568 O-Ring sizes (the AS 568 tube fitting O-Rings are not included). The ISO 3601-1 Size Code for these O-Rings is the same as the AS 568 dash number. The second group of O-Rings are "metric" sizes and are designated for Aerospace applications. The first digit of the Size Code indicates the cross section group (A-E), while the last four digits indicate the O-Ring inside diameter rounded to one-tenth millimeter. Complete item designations for both types include the word O-Ring followed by a hyphen and ISO 3601-1, followed by another hyphen and the Size Code and a letter indicating the tolerance class, another hyphen and a description of the size, and a final hyphen and a letter code indicating the Grade. Additionally, O-Rings intended for Aerospace use will be indicated by the letter A following 3601-1 (3601-1A) in the item designation. The tolerance classes are designated by the letters A and B (A is tighter). Aerospace O-Rings have only one tolerance class. Grade codes, N, S, and CS indicate General Purpose, Special, and Critical Service respectively. The grades are primarily visual inspection standards and are defined in ISO 3601-3. [ O-ring - ISO 3601-1 - 011 A - 7,65 x 1,78 - S ] - General Industrial [ O-ring - ISO 3601-1 A - C0545 - 54,5 x 3,55 - S ] - Aerospace DIN 3771 is produced by the Duetsches Institut für Normung (German Institute for Standards). O-Ring sizes are identified by the ID x C/S, followed by a letter indicating the Quality Level, and a code indicating the rubber polymer and IRHD hardness. Two Quality levels are specified: N - Normal Quality (1.0 AQL), S - Special Quality (.65 AQL). [ O-ring DIN 3771 - 13,2 x 1,8 - N - NBR 70 ] Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 2 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com International O-Ring Standard Cross Reference NF T 47-501 is issued by the Association Française de Normalisation (French Standards Institute). It is very similar to ISO 3601-1 in both the sizes included and part nomenclature. O-Rings are designated with a size code that is made up of a letters corresponding to each of 5 cross section groups (A-E), 4 digits indicating ID rounded to .1 mm, a 2nd letter indicating Precision Class and a 3rd letter indicating Visual (inspection) Class. The Precision Class is indicated by the letter A, for Aerospace applications, and G for General Purpose applications. The visual classes are N (1.0 AQL) and S (.65 AQL). [ O-ring NF T 47-501 A0224 A S ] JIS B 2401, a Japanese Industrial Standard, has two groupings of O-Ring sizes. The first group consists of two sets of O-Rings designed for General Purpose and for Aerospace applications. These O-Rings are mostly a subset of ISO 3601-1 with a few additional sizes. O-Rings are identified simply by their dimensions, ID first and then C/S, plus a Series Letter. The Series Letter is used to indicate the application: G indicates General use, while A indicates Aerospace applications. Aerospace O-Rings are held to closer tolerances than the General Purpose O-Rings. In our tables, the ISO O-Rings are indicated solely by the letters A or G. [ O-ring 7.5 x 1.8 - G - S ] The second, more traditional group is organized into three sections: Moving (dynamic), designated by the letter P, Fixing (static), designated by the letter G, and Vacuum Flange, designated by the letter V. The O-Rings in each section have insignificant ascending numbers to complete the size code. Like the ISO group, the traditional part numbers include a Grade letter. In our tables the traditional group O-Rings are identified by their size code labels. [ O-ring Type 1A G80 N ] Unlike the other standards listed here, JIS B 2401 calls out 6 material classes: 1A, 1B, 2, 3, 4C and 4D. We do not address them in this publication— see our Compound Selection Guide, or contact us for the PAI compounds meeting these classes. BS 4518, also from the British Standards Institution, identifies British Standard metric sizes. The size code for these O-Rings is a four digit number indicating the O-Ring I.D. in tenths of millimeters followed by a hyphen and two digits indicating the O-Ring Cross Section, also in tenths of a millimeter. ] BS 4518 0645 - 24 ] SMS 1586 is a Sveriges Mekanstandardisering (Swedish Mechanical Standard). O-Rings are simply identified by ID and C/S similar to DIN 3771. SMS 1586 O-Rings are classified into two groupings. The first group, intended for dynamic and static installations is indicated in our table by the letter D. The second group, intended mainly for static applications, is indicated with an S. [ “O”-ring SMS 1586 3.3 x 2.4 - (mat’l per SMS 1587) ] IS0 6149 covers O-Rings designed for use in Metric Tube Fittings. Unlike AS 568, ISO 3601 does not include these O-Rings. There is a separate table on the last inside page of this publication that references these 13 sizes. The tables on the following pages list 1,484 different O-Ring sizes. While Precision Associates has over 2,200 O-Ring sizes, we are not tooled for all of the O-Rings in these pages. O-Rings that we are tooled for are indicated in the first column of the table. If you find that we don’t have a tool listed, please call us as we regularly ad sizes to our repertoire. If not, we can usually produce a mold in short order in our on-site mold shop. As stated earlier in this section, this publication is only intended to identify O-Ring sizes from the various specification designations. Every effort was made to make sure that the information presented here is correct, but we recommend referral to the actual specifications before proceeding with design work, etc. You may contact Precision Associates for complete information regarding tolerances, inspection requirements and materials. Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com 3 International O-Ring Standard Cross Reference -007 -008 -009 -003 003 -902 -903 -004 -005 -006 -801 -007 -008 -802 -009 SMS-1586 -902 -903 -004 -005 -006 001 BS 4518 -002 -905 -003 -001 -606 -607 -002 JIS B2401 1-902 1-903 1-004 1-005 1-006 70-125 1-007 1-008 70-187 1-009 -001 NF T47-501 * 63-594VS I.D. inch .029 .070 .100 .042 .185 .056 .122 .161 .201 .240 .280 .319 .358 .398 .437 .476 .516 .555 .594 .634 .673 .713 .752 .870 .988 1.067 1.146 1.264 1.382 1.461 .239 .301 .070 .101 .114 .125 .145 .176 .187 .208 DIN 3771 63-319 C/S inch .040 .040 .040 .050 .056 .060 .063 .063 .063 .063 .063 .063 .063 .063 .063 .063 .063 .063 .063 .063 .063 .063 .063 .063 .063 .063 .063 .063 .063 .063 .064 .064 .070 .070 .070 .070 .070 .070 .070 .070 ISO 3601 63-240 I.D. mm 0,74 1,78 2,54 1,07 4,70 1,42 3,10 4,10 5,10 6,10 7,10 8,10 9,10 10,10 11,10 12,10 13,10 14,10 15,10 16,10 17,10 18,10 19,10 22,10 25,10 27,10 29,10 32,10 35,10 37,10 6,07 7,65 1,78 2,57 2,90 3,18 3,68 4,47 4,75 5,28 BS 1806 1-002 1-905 1-003 * 63-122VS C/S mm 1,02 1,02 1,02 1,27 1,42 1,52 1,60 1,60 1,60 1,60 1,60 1,60 1,60 1,60 1,60 1,60 1,60 1,60 1,60 1,60 1,60 1,60 1,60 1,60 1,60 1,60 1,60 1,60 1,60 1,60 1,63 1,63 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 AS 568 PAI Size 1-001 40-70 0031-16 0041-16 0051-16 0061-16 0071-16 0081-16 0091-16 0101-16 0111-16 0121-16 0131-16 0141-16 0151-16 0161-16 0171-16 0181-16 0191-16 0221-16 0251-16 0271-16 0291-16 0321-16 0351-16 0371-16 S S S S S S S S S S S S S S S S S S S S S S S S 002 004 005 006 007 008 009 * Mold is cut for non-standard shrink compensation Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 4 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com International O-Ring Standard Cross Reference -014 -015 -016 -017 -018 -019 -020 -021 -022 -023 -024 -025 -026 -027 -028 -029 -030 -031 -032 -033 -034 -035 -036 -037 -038 -039 -040 -041 SMS-1586 -012 -013 010 BS 4518 -011 -010 -803 -610 -011 -804 -611 -012 -013 -806 -014 -015 -016 -017 -018 -019 -020 -021 -022 -023 -024 -025 -026 -027 -028 -517 -029 -519 -030 -031 -032 -033 -034 -035 -036 -037 -038 -039 -040 -041 -532 JIS B2401 -010 NF T47-501 I.D. inch .239 .250 .266 .301 .313 .344 .364 .426 .437 .489 .551 .614 .676 .739 .801 .864 .926 .989 1.051 1.114 1.176 1.239 1.301 1.364 1.428 1.489 1.553 1.614 1.739 1.864 1.989 2.114 2.239 2.364 2.489 2.614 2.739 2.864 2.989 3.110 DIN 3771 C/S inch .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 ISO 3601 1-030 1-031 1-032 1-033 1-034 1-035 1-036 1-037 1-038 1-039 1-040 1-041 I.D. mm 6,07 6,35 6,76 7,65 7,94 8,74 9,25 10,82 11,10 12,42 14,00 15,60 17,17 18,77 20,35 21,95 23,52 25,12 26,70 28,30 29,87 31,47 33,05 34,65 36,27 37,82 39,45 41,00 44,17 47,35 50,52 53,70 56,87 60,05 63,22 66,40 69,57 72,75 75,92 78,99 BS 1806 1-011 * 70-313ES * 70-344SS 1-012 1-013 70-437 1-014 1-015 1-016 1-017 1-018 1-019 1-020 1-021 1-022 1-023 1-024 1-025 1-026 1-027 1-028 70-1.427 1-029 C/S mm 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 AS 568 PAI Size 1-010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 Contact Precision Associates for sizes not listed Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com 5 International O-Ring Standard Cross Reference * 70-98SS 71-147 -045 -046 -047 -048 -049 -050 71-178 * Mold is cut for non-standard shrink compensation Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 6 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 1,80 X 1,80 2,00 X 1,80 2,24 X 1,80 2,50 X 1,80 2,80 X 1,80 3,15 X 1,80 3,55 X 1,80 3,75 X 1,80 4,00 X 1,80 4,50 X 1,80 A0018 A0020 A0022 A0025 A0028 A0032 A0036 A0038 A0040 A0045 A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G SMS-1586 1-050 -044 042 BS 4518 1-049 -043 -042 -534 -043 -536 -044 -538 -045 -540 -046 -542 -047 -544 -048 -546 -049 -548 -050 -550 -551 -552 -553 -554 -555 -556 -557 -558 -559 -560 -561 -562 JIS B2401 1-048 -042 NF T47-501 1-047 I.D. inch 3.239 3.360 3.489 3.610 3.739 3.860 3.989 4.110 4.239 4.360 4.489 4.610 4.739 4.860 4.989 5.095 5.239 5.345 5.470 5.595 5.720 5.845 5.970 6.095 6.220 6.345 6.470 6.695 6.720 6.845 .071 .079 .088 .098 .110 .124 .140 .148 .157 .177 DIN 3771 1-046 C/S inch .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .070 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 ISO 3601 1-044 70-3.860 1-045 I.D. mm 82,27 85,34 88,62 91,69 94,97 98,04 101,32 104,39 107,67 110,74 114,02 117,09 120,37 123,44 126,72 129,41 133,07 135,76 138,94 142,11 145,29 148,46 151,64 154,81 157,99 161,16 164,34 170,05 170,69 173,86 1,80 2,00 2,24 2,50 2,80 3,15 3,55 3,75 4,00 4,50 BS 1806 1-043 C/S mm 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,78 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 AS 568 PAI Size 1-042 043 044 045 046 047 048 049 050 A0018 A0020 A0022 A0025 A0028 A0032 A0036 A0038 A0040 A0045 www.PrecisionAssoc.com International O-Ring Standard Cross Reference A0100 A0106 A0112 10,00 X 1,80 10,60 X 1,80 11,20 X 1,80 A0118 11,80 X 1,80 A0125 12,50 X 1,80 A0132 A0140 13,20 X 1,80 14,00 X 1,80 A0150 15,00 X 1,80 A0160 A0170 A0180 A0190 A0200 16,00 X 1,80 17,00 X 1,80 A0212 A0224 A0100 A0106 A0112 A0116 A0118 A0121 A0125 A0128 A0132 A0140 A0145 A0150 A0155 A0160 A0170 A0180 A0190 A0200 A0206 A0212 A0224 SMS-1586 4,87 X 1,80 5,00 X 1,80 5,15 X 1,80 5,30 X 1,80 5,60 X 1,80 6,00 X 1,80 6,30 X 1,80 6,70 X 1,80 6,90 X 1,80 7,10 X 1,80 7,50 X 1,80 8,00 X 1,80 8,50 X 1,80 8,75 X 1,80 9,00 X 1,80 9,50 X 1,80 BS 4518 A0049 A0050 A0052 A0053 A0056 A0060 A0063 A0067 A0069 A0071 A0075 A0080 A0085 A0088 A0090 A0095 A0048 A0049 A0050 A0052 A0053 A0056 A0060 A0063 A0067 A0069 A0071 A0075 A0080 A0085 A0088 A0090 A0095 JIS B2401 71-810 NF T47-501 70-739VS I.D. inch .187 .192 .197 .203 .209 .220 .236 .248 .264 .272 .280 .295 .315 .335 .344 .354 .374 .384 .394 .417 .441 .457 .465 .476 .492 .504 .520 .551 .571 .591 .610 .630 .669 .709 .748 .787 .811 .835 .882 .906 DIN 3771 70-495SS C/S inch .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 ISO 3601 71-248 I.D. mm 4,75 4,87 5,00 5,15 5,30 5,60 6,00 6,30 6,70 6,90 7,10 7,50 8,00 8,50 8,75 9,00 9,50 9,75 10,00 10,60 11,20 11,60 11,80 12,10 12,50 12,80 13,20 14,00 14,50 15,00 15,50 16,00 17,00 18,00 19,00 20,00 20,60 21,20 22,40 23,00 BS 1806 71-210 C/S mm 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 1,80 AS 568 PAI Size G A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G G A,G A,G A,G G A,G G A,G G A,G A,G G A,G G A,G A,G A,G A,G A,G G A,G A,G G Contact Precision Associates for sizes not listed Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com 7 International O-Ring Standard Cross Reference A0475 A0500 A0530 A0560 A0600 A0630 A0670 A0710 A0750 A0800 A0850 A0900 A0950 A1000 A1060 A1120 A0300 A0315 A0325 A0335 A0345 A0355 A0365 A0375 A0387 A0400 A0412 A0425 A0437 A0450 A0462 A0475 A0487 A0500 SMS-1586 A0300 A0315 A0325 A0335 A0345 A0355 A0365 A0375 A0387 A0400 A0412 A0425 A0437 A0450 BS 4518 8 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 A0280 A0236 A0243 A0250 A0258 A0265 A0273 A0280 JIS B2401 Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 A0250 A0258 A0265 NF T47-501 * 71-4.409VS * Mold is cut for non-standard shrink compensation A0236 DIN 3771 * 71-2.638VS I.D. inch .929 .957 .984 1.016 1.043 1.075 1.102 1.142 1.181 1.240 1.280 1.319 1.358 1.398 1.437 1.476 1.524 1.575 1.622 1.673 1.720 1.772 1.819 1.870 1.917 1.969 2.087 2.205 2.362 2.480 2.638 2.795 2.953 3.150 3.346 3.543 3.740 3.937 4.173 4.409 ISO 3601 70-1.378VS C/S inch .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 .071 BS 1806 * 71-1.280VS C/S I.D. mm mm 1,80 23,60 1,80 24,30 1,80 25,00 1,80 25,80 1,80 26,50 1,80 27,30 1,80 28,00 1,80 29,00 1,80 30,00 1,80 31,50 1,80 32,50 1,80 33,50 1,80 34,50 1,80 35,50 1,80 36,50 1,80 37,50 1,80 38,70 1,80 40,00 1,80 41,20 1,80 42,50 1,80 43,70 1,80 45,00 1,80 46,20 1,80 47,50 1,80 48,70 1,80 50,00 1,80 53,00 1,80 56,00 1,80 60,00 1,80 63,00 1,80 67,00 1,80 71,00 1,80 75,00 1,80 80,00 1,80 85,00 1,80 90,00 1,80 95,00 1,80 100,00 1,80 106,00 1,80 112,00 AS 568 PAI Size A,G G A,G A,G A,G G A,G G A,G A A A A A A A A A A A A A A A A A A A A A A A A A A A A A www.PrecisionAssoc.com International O-Ring Standard Cross Reference * 94-445VS 94-523 SMS-1586 * 94-366SS BS 4518 * 94-287VS JIS B2401 * 94-248VS A1180 A1250 NF T47-501 94-142 I.D. inch 4.646 4.921 .351 .414 .110 .150 .189 .228 .268 .307 .346 .386 .468 .530 .644 .130 .142 .169 .181 .209 .220 .248 .260 .287 .299 .327 .339 .366 .378 .386 .406 .417 .425 .433 .445 .457 .465 .484 .496 .524 DIN 3771 * 75-386VS 1-906 1-907 1-908 C/S inch .071 .071 .072 .072 .075 .075 .075 .075 .075 .075 .075 .075 .078 .082 .087 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 ISO 3601 * 75-268SS I.D. mm 118,00 125,00 8,92 10,52 2,80 3,80 4,80 5,80 6,80 7,80 8,80 9,80 11,89 13,46 16,36 3,30 3,60 4,30 4,60 5,30 5,60 6,30 6,60 7,30 7,60 8,30 8,60 9,30 9,60 9,80 10,30 10,60 10,80 11,00 11,30 11,60 11,80 12,30 12,60 13,30 BS 1806 1-904 1-905 C/S mm 1,80 1,80 1,83 1,83 1,90 1,90 1,90 1,90 1,90 1,90 1,90 1,90 1,98 2,08 2,21 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 AS 568 PAI Size A A -904 -905 P3 P4 P5 P6 P7 P8 P9 P10 -906 -907 -908 D 0036-24 D 0046-24 D 0056-24 D 0066-24 D 0076-24 D 0086-24 D 0096-24 P10A D 0106-24 P11 P11.2 D 0116-24 P12 P12.5 D 0126-24 D Contact Precision Associates for sizes not listed Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com 9 International O-Ring Standard Cross Reference SMS-1586 BS 4518 JIS B2401 NF T47-501 I.D. inch .535 .543 .563 .575 .583 .602 .614 .622 .642 .654 .681 .693 .701 .732 .772 .780 .811 .819 .850 .858 .969 1.087 1.165 1.244 1.362 1.402 1.480 1.559 1.638 1.756 1.795 1.874 1.953 2.031 2.150 2.189 2.268 2.307 2.346 2.425 DIN 3771 C/S inch .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 .094 ISO 3601 I.D. mm 13,60 13,80 14,30 14,60 14,80 15,30 15,60 15,80 16,30 16,60 17,30 17,60 17,80 18,60 19,60 19,80 20,60 20,80 21,60 21,80 24,60 27,60 29,60 31,60 34,60 35,60 37,60 39,60 41,60 44,60 45,60 47,60 49,60 51,60 54,60 55,60 57,60 58,60 59,60 61,60 BS 1806 94-602 * 94-614SS C/S mm 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 2,40 AS 568 PAI Size 0136-24 P14 D 0146-24 P15 D 0156-24 P16 D 0166-24 D 0176-24 P18 0186-24 0196-24 P20 0206-24 P21 0216-24 P22 0246-24 0276-24 0296-24 0316-24 0346-24 0356-24 0376-24 0396-24 0416-24 0446-24 0456-24 0476-24 0496-24 0516-24 0546-24 0556-24 0576-24 0586-24 0596-24 0616-24 * Mold is cut for non-standard shrink compensation Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 10 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com International O-Ring Standard Cross Reference 1-119 1-120 1-121 1-122 1-123 1-124 SMS-1586 1-118 BS 4518 1-116 1-117 JIS B2401 1-115 NF T47-501 1-114 I.D. inch 2.465 2.543 2.661 2.740 .706 .755 .049 .081 .112 .143 .175 .206 .237 .299 .362 .391 .424 .469 .487 .500 .516 .549 .594 .612 .625 .674 .687 .703 .737 .799 .812 .862 .875 .924 .937 .987 1.049 1.112 1.174 1.237 DIN 3771 1-113 C/S inch .094 .094 .094 .094 .097 .097 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 ISO 3601 1-112 I.D. mm 62,60 64,60 67,60 69,60 17,93 19,18 1,24 2,06 2,84 3,63 4,45 5,23 6,02 7,59 9,19 9,93 10,77 11,91 12,37 12,70 13,11 13,94 15,09 15,54 15,88 17,12 17,45 17,86 18,72 20,29 20,62 21,89 22,23 23,47 23,80 25,07 26,64 28,24 29,82 31,42 BS 1806 1-909 1-910 1-102 1-103 1-104 1-105 1-106 1-107 1-108 1-109 1-110 103-391 1-111 C/S mm 2,40 2,40 2,40 2,40 2,46 2,46 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 AS 568 PAI Size 0626-24 0646-24 0676-24 0696-24 -909 -910 -102 -103 -104 -105 -106 -107 -108 -109 -110 -111 -112 -113 -114 -115 -116 -117 -118 -119 -120 -121 -122 -123 -124 -102 -103 -104 -105 -106 -107 -108 -109 -110 -613 -111 -614 -112 -807 -615 -113 -616 -114 -809 -115 -810 -617 -116 -117 -812 -118 -813 -119 -814 -120 -121 -122 -123 -124 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 Contact Precision Associates for sizes not listed Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com 11 International O-Ring Standard Cross Reference -153 -154 -155 -156 -157 -158 -159 -160 SMS-1586 -152 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 BS 4518 -151 -125 -126 -127 -128 -129 -130 -131 -132 -133 -134 -135 -136 -137 -138 -139 -140 -141 -142 -143 -144 -145 -146 -147 -148 -149 -150 -640 -151 -641 -642 -152 -643 -153 -154 -155 -156 -157 -158 -159 -160 JIS B2401 -125 -126 -127 -128 -129 -130 -131 -132 -133 -134 -135 -136 -137 -138 -139 -140 -141 -142 -143 -144 -145 -146 -147 -148 -149 -150 NF T47-501 I.D. inch 1.299 1.362 1.424 1.487 1.549 1.612 1.674 1.737 1.799 1.862 1.925 1.987 2.050 2.112 2.175 2.237 2.300 2.362 2.425 2.487 2.550 2.612 2.675 2.737 2.800 2.862 2.924 2.987 3.049 3.174 3.237 3.299 3.487 3.737 3.987 4.237 4.487 4.737 4.987 5.237 DIN 3771 1-153 1-154 1-155 1-156 1-157 1-158 1-159 1-160 C/S inch .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 ISO 3601 1-152 I.D. mm 32,99 34,59 36,17 37,77 39,34 40,94 42,52 44,12 45,69 47,29 48,90 50,47 52,07 53,64 55,25 56,82 58,42 59,99 61,60 63,17 64,77 66,34 67,95 69,52 71,12 72,69 74,27 75,87 77,44 80,62 82,22 83,79 88,57 94,92 101,27 107,62 113,97 120,32 126,67 133,02 BS 1806 1-151 C/S mm 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 AS 568 PAI Size 1-125 1-126 1-127 1-128 1-129 1-130 1-131 1-132 1-133 1-134 1-135 1-136 1-137 1-138 1-139 1-140 1-141 1-142 1-143 1-144 1-145 1-146 1-147 1-148 1-149 1-150 151 152 153 154 155 156 157 158 159 160 * Mold is cut for non-standard shrink compensation Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 12 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com International O-Ring Standard Cross Reference B0045 B0053 B0060 B0069 B0080 B0090 B0095 B0100 B0106 B0112 B0132 B0140 14,00 X 2,65 B0150 15,00 X 2,65 B0090 B0095 B0100 B0106 B0112 B0116 B0118 B0121 B0125 B0128 B0132 B0140 B0145 B0150 B0160 16,00 X 2,65 B0160 B0118 B0125 SMS-1586 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 BS 4518 -161 -162 -163 -164 -165 -166 -167 -168 -169 -170 -171 -172 -173 -174 -175 -176 -177 -178 JIS B2401 -161 -162 -163 -164 -165 -166 -167 -168 -169 -170 -171 -172 -173 -174 -175 -176 -177 -178 NF T47-501 I.D. inch 5.487 5.737 5.987 6.237 6.487 6.737 6.987 7.237 7.487 7.737 7.987 8.237 8.487 8.737 8.987 9.237 9.487 9.737 9.987 .177 .209 .236 .272 .315 .354 .374 .394 .417 .441 .457 .465 .476 .492 .504 .520 .551 .571 .591 .610 .630 DIN 3771 104-492 C/S inch .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .103 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 ISO 3601 * 104-417VS I.D. mm 139,37 145,72 152,07 158,42 164,77 171,12 177,47 183,82 190,17 196,52 202,87 209,22 215,57 221,92 228,27 234,62 240,97 247,32 253,67 4,50 5,30 6,00 6,90 8,00 9,00 9,50 10,00 10,60 11,20 11,60 11,80 12,10 12,50 12,80 13,20 14,00 14,50 15,00 15,50 16,00 BS 1806 * 104-272VS C/S mm 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,62 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 AS 568 PAI Size 1-161 1-162 1-163 1-164 1-165 1-166 1-167 1-168 1-169 1-170 1-171 1-172 1-173 1-174 1-175 1-176 1-177 1-178 1-179 A A A A A A A A A A A A A A,G G A,G G A,G Contact Precision Associates for sizes not listed Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com 13 International O-Ring Standard Cross Reference B0212 B0224 21,20 X 2,65 22,40 X 2,65 B0236 23,60 X 2,65 B0250 B0258 B0265 25,00 X 2,65 25,80 X 2,65 26,50 X 2,65 B0280 28,00 X 2,65 B0300 B0315 B0325 B0335 B0345 B0355 B0365 B0375 B0387 B0400 B0412 B0425 B0437 B0450 B0462 B0475 B0487 B0500 B0515 B0530 B0545 B0560 B0580 B0600 30,00 X 2,65 31,50 X 2,65 32,50 X 2,65 33,50 X 2,65 34,50 X 2,65 35,50 X 2,65 36,50 X 2,65 37,50 X 2,65 38,70 X 2,65 B0170 B0180 B0190 B0200 B0206 B0212 B0224 B0236 B0243 B0250 B0258 B0265 B0273 B0280 B0300 B0315 B0325 B0335 B0345 B0355 B0365 B0375 B0387 B0400 B0412 B0425 B0437 B0450 B0462 B0475 B0487 B0500 B0515 B0530 B0545 B0560 B0580 B0600 SMS-1586 17,00 X 2,65 18,00 X 2,65 19,00 X 2,65 20,00 X 2,65 BS 4518 B0170 B0180 B0190 B0200 JIS B2401 NF T47-501 I.D. inch .669 .709 .748 .787 .811 .835 .882 .906 .929 .957 .984 1.016 1.043 1.075 1.102 1.142 1.181 1.240 1.280 1.319 1.358 1.398 1.437 1.476 1.524 1.575 1.622 1.673 1.720 1.772 1.819 1.870 1.917 1.969 2.028 2.087 2.146 2.205 2.283 2.362 DIN 3771 C/S inch .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 ISO 3601 * 104-835VS I.D. mm 17,00 18,00 19,00 20,00 20,60 21,20 22,40 23,00 23,60 24,30 25,00 25,80 26,50 27,30 28,00 29,00 30,00 31,50 32,50 33,50 34,50 35,50 36,50 37,50 38,70 40,00 41,20 42,50 43,70 45,00 46,20 47,50 48,70 50,00 51,50 53,00 54,50 56,00 58,00 60,00 BS 1806 * 104-787VS C/S mm 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 AS 568 PAI Size A,G A,G A,G A,G G A,G A,G G A,G G A,G A,G A,G G A,G G A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G A,G * Mold is cut for non-standard shrink compensation Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 14 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com International O-Ring Standard Cross Reference B0900 B0950 B1000 B1060 B1120 B1180 B1250 B1320 B1400 B1500 B1600 B1700 B1800 B1900 B2000 B2120 B2240 B2300 SMS-1586 B0850 BS 4518 B0800 B0615 B0630 B0650 B0670 B0690 B0710 B0730 B0750 B0775 B0800 B0825 B0850 B0875 B0900 B0925 B0950 B0975 B1000 JIS B2401 B0615 B0630 B0650 B0670 B0690 B0710 B0730 B0750 NF T47-501 104-6.299 I.D. inch 2.421 2.480 2.559 2.638 2.717 2.795 2.874 2.953 3.051 3.150 3.248 3.346 3.445 3.543 3.642 3.740 3.839 3.937 4.055 4.173 4.409 4.646 4.921 5.197 5.512 5.709 5.906 6.120 6.299 6.496 6.693 6.890 7.087 7.283 7.480 7.677 7.874 8.346 8.819 9.055 DIN 3771 104-5.512 C/S inch .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 .104 ISO 3601 104-2.874 I.D. mm 61,50 63,00 65,00 67,00 69,00 71,00 73,00 75,00 77,50 80,00 82,50 85,00 87,50 90,00 92,50 95,00 97,50 100,00 103,00 106,00 112,00 118,00 125,00 132,00 140,00 145,00 150,00 155,00 160,00 165,00 170,00 175,00 180,00 185,00 190,00 195,00 200,00 212,00 224,00 230,00 BS 1806 104-2.638 C/S mm 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 2,65 AS 568 PAI Size A,G A,G A,G A,G A,G A,G A,G A,G G G G A,G G A,G G A,G G A,G G A,G A A A A A A A A A A A A A A A A Contact Precision Associates for sizes not listed Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com 15 International O-Ring Standard Cross Reference SMS-1586 BS 4518 JIS B2401 * 118-1.673VS 1-924 NF T47-501 * 118-1.543VS DIN 3771 1-920 I.D. inch 9.291 9.567 9.843 .863 .924 .986 1.047 1.109 1.171 1.355 .756 .768 .846 .874 .886 .953 .965 1.004 1.031 1.043 1.083 1.150 1.161 1.240 1.268 1.280 1.346 1.358 1.398 1.425 1.437 1.475 1.476 1.543 1.555 1.634 1.661 1.673 1.720 1.740 ISO 3601 * 118-886SS 118-953 C/S inch .104 .104 .104 .116 .116 .116 .116 .116 .116 .116 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 BS 1806 1-911 1-912 1-913 1-914 1-915 1-916 1-918 C/S I.D. mm mm 2,65 236,00 2,65 243,00 2,65 250,00 2,95 21,92 2,95 23,47 2,95 25,04 2,95 26,59 2,95 28,17 2,95 29,74 2,95 34,42 3,00 19,20 3,00 19,50 3,00 21,50 3,00 22,20 3,00 22,50 3,00 24,20 3,00 24,50 3,00 25,50 3,00 26,20 3,00 26,50 3,00 27,50 3,00 29,20 3,00 29,50 3,00 31,50 3,00 32,20 3,00 32,50 3,00 34,20 3,00 34,50 3,00 35,50 3,00 36,20 3,00 36,50 3,00 37,47 3,00 37,50 3,00 39,20 3,00 39,50 3,00 41,50 3,00 42,20 3,00 42,50 3,00 43,69 3,00 44,20 AS 568 PAI Size B2360 B2430 B2500 -911 -912 -913 -914 -916 -918 D 0195-30 0215-30 D 0225-30 D 0245-30 0255-30 D 0265-30 0275-30 D 0295-30 0315-30 D 0325-30 D 0345-30 0355-30 D 0365-30 -920 0375-30 D 0395-30 0415-30 D 0425-30 -924 D * Mold is cut for non-standard shrink compensation Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 16 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com International O-Ring Standard Cross Reference BS 4518 SMS-1586 JIS B2401 NF T47-501 118-5.492 118-5.689 I.D. inch 1.752 1.949 2.090 -928 2.146 2.185 2.264 2.337 -932 2.343 2.461 2.539 2.736 2.933 3.130 3.327 3.524 3.720 3.917 4.114 4.311 4.508 4.705 4.902 5.098 5.295 5.492 5.689 5.886 6.083 6.280 6.476 6.673 6.870 7.067 7.264 7.461 7.657 7.854 8.248 8.642 9.035 DIN 3771 118-3.130 C/S inch .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 .118 ISO 3601 1-932 118-2.342 I.D. mm 44,50 49,50 53,09 54,50 55,50 57,50 59,36 59,50 62,50 64,50 69,50 74,50 79,50 84,50 89,50 94,50 99,50 104,50 109,50 114,50 119,50 124,50 129,50 134,50 139,50 144,50 149,50 154,50 159,50 164,50 169,50 174,50 179,50 184,50 189,50 194,50 199,50 209,50 219,50 229,50 BS 1806 1-928 C/S mm 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 3,00 AS 568 PAI Size 0445-30 0495-30 S 0545-30 0555-30 0575-30 S 0595-30 0625-30 0645-30 0695-30 0745-30 0795-30 0845-30 0895-30 0945-30 0995-30 1045-30 1095-30 1145-30 1195-30 1245-30 1295-30 1345-30 1395-30 1445-30 1495-30 1545-30 1595-30 1645-30 1695-30 1745-30 1795-30 1845-30 1895-30 1945-30 1995-30 2095-30 2195-30 2295-30 S S S S S S S S S S S S S S S S S S Contact Precision Associates for sizes not listed Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com 17 International O-Ring Standard Cross Reference SMS-1586 BS 4518 JIS B2401 NF T47-501 I.D. inch 9.429 9.626 9.823 .961 1.157 1.354 1.551 1.748 1.945 2.142 2.339 2.535 2.732 2.929 3.126 3.323 3.520 3.717 3.913 4.110 4.307 4.504 4.701 4.898 5.094 5.291 5.488 5.685 .854 .870 .933 .972 .992 1.012 1.091 1.130 1.150 1.169 1.209 1.228 DIN 3771 C/S inch .118 .118 .118 .122 .122 .122 .122 .122 .122 .122 .122 .122 .122 .122 .122 .122 .122 .122 .122 .122 .122 .122 .122 .122 .122 .122 .122 .122 .138 .138 .138 .138 .138 .138 .138 .138 .138 .138 .138 .138 ISO 3601 I.D. mm 239,50 244,50 249,50 24,40 29,40 34,40 39,40 44,40 49,40 54,40 59,40 64,40 69,40 74,40 79,40 84,40 89,40 94,40 99,40 104,40 109,40 114,40 119,40 124,40 129,40 134,40 139,40 144,40 21,70 22,10 23,70 24,70 25,20 25,70 27,70 28,70 29,20 29,70 30,70 31,20 BS 1806 122-3.520 C/S mm 3,00 3,00 3,00 3,10 3,10 3,10 3,10 3,10 3,10 3,10 3,10 3,10 3,10 3,10 3,10 3,10 3,10 3,10 3,10 3,10 3,10 3,10 3,10 3,10 3,10 3,10 3,10 3,10 3,50 3,50 3,50 3,50 3,50 3,50 3,50 3,50 3,50 3,50 3,50 3,50 AS 568 PAI Size 2395-30 2445-30 2495-30 G25 G30 G35 G40 G45 G50 G55 G60 G65 G70 G75 G80 G85 G90 G95 G100 G105 G110 G115 G120 G125 G130 G135 G140 G145 P22A P22.4 P24 P25 P25.5 P26 P28 P29 P29.5 P30 P31 P31.5 * Mold is cut for non-standard shrink compensation Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 18 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com International O-Ring Standard Cross Reference SMS-1586 BS 4518 JIS B2401 NF T47-501 I.D. inch 1.248 1.327 1.366 1.386 1.406 1.484 1.524 1.563 1.602 1.642 1.720 1.760 1.799 1.878 1.917 1.957 .171 .234 .296 .359 .421 .484 .549 .609 .672 .734 .796 .859 .921 .984 1.016 1.046 1.109 1.171 1.234 1.296 1.359 1.421 1.484 1.563 DIN 3771 C/S inch .138 .138 .138 .138 .138 .138 .138 .138 .138 .138 .138 .138 .138 .138 .138 .138 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 ISO 3601 1-215 1-216 1-217 1-218 1-219 1-220 1-221 1-222 I.D. mm 31,70 33,70 34,70 35,20 35,70 37,70 38,70 39,70 40,70 41,70 43,70 44,70 45,70 47,70 48,70 49,70 4,34 5,94 7,52 9,12 10,69 12,29 13,94 15,47 17,07 18,64 20,22 21,82 23,39 24,99 25,81 26,57 28,17 29,74 31,34 32,92 34,52 36,09 37,69 39,70 BS 1806 1-201 1-202 1-203 1-204 1-205 1-206 1-207 1-208 1-209 1-210 1-211 1-212 1-213 1-214 C/S mm 3,50 3,50 3,50 3,50 3,50 3,50 3,50 3,50 3,50 3,50 3,50 3,50 3,50 3,50 3,50 3,50 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 AS 568 PAI Size P32 P34 P35 P35. P36 P38 P39 P40 P41 P42 P44 P45 P46 P48 P49 P50 -201 -202 -203 -204 -205 -206 -207 -208 -209 -210 -211 -212 -213 -214 -215 -216 -217 -218 -219 -220 -221 -222 -201 -202 -203 -204 -205 -206 -207 -208 -209 -210 -211 -212 -213 -214 -618 -215 -216 -217 -218 -219 -220 -221 -222 -824 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 Contact Precision Associates for sizes not listed Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com 19 International O-Ring Standard Cross Reference 1-231 1-232 1-233 1-234 1-235 1-236 1-237 1-238 1-239 1-240 -226 -227 -228 -229 -230 -231 -232 -233 -234 -235 -236 -237 -238 -239 -240 SMS-1586 1-230 -225 223 BS 4518 1-229 -224 -223 -825 -826 -224 -827 -828 -225 -829 -830 -226 -831 -832 -227 -833 -834 -228 -835 -836 -229 -837 -838 -230 -839 -840 -231 -841 -842 -232 -843 -844 -233 -845 -846 -234 -235 -236 -237 -238 -239 -240 JIS B2401 1-228 -223 NF T47-501 1-227 I.D. inch 1.609 1.625 1.687 1.734 1.750 1.813 1.859 1.875 1.937 1.984 2.000 2.063 2.109 2.125 2.187 2.234 2.250 2.313 2.359 2.375 2.437 2.484 2.500 2.563 2.609 2.625 2.687 2.734 2.750 2.813 2.859 2.875 2.937 2.984 3.109 3.234 3.359 3.484 3.609 3.734 DIN 3771 1-226 C/S inch .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 ISO 3601 1-225 I.D. mm 40,87 41,28 42,85 44,04 44,45 46,04 47,22 47,63 49,20 50,39 50,80 52,39 53,57 53,98 55,55 56,74 57,15 58,74 59,92 60,33 61,90 63,09 63,50 65,10 66,27 66,68 68,25 69,44 69,85 71,44 72,62 73,03 74,60 75,79 78,97 82,14 85,32 88,49 91,67 94,84 BS 1806 1-224 C/S mm 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 AS 568 PAI Size 1-223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 * Mold is cut for non-standard shrink compensation Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 20 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com International O-Ring Standard Cross Reference SMS-1586 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 BS 4518 -241 -242 -243 -244 -245 -246 -247 -248 -249 -250 -251 -252 -253 -254 -255 -256 -257 -258 -259 -260 -261 -262 -263 -264 -265 -266 -267 -268 -269 -270 -271 -272 -273 -274 -275 -276 -277 -278 -279 -280 JIS B2401 -241 -242 -243 -244 -245 -246 -247 -248 -249 -250 -251 -252 -253 -254 -255 -256 -257 -258 -259 -260 -261 -262 -263 -264 -265 -266 -267 -268 -269 -270 -271 -272 -273 -274 -275 -276 -277 -278 -279 -280 NF T47-501 I.D. inch 3.859 3.984 4.109 4.234 4.359 4.484 4.609 4.734 4.859 4.984 5.109 5.234 5.359 5.484 5.609 5.734 5.859 5.984 6.234 6.484 6.734 6.984 7.234 7.484 7.734 7.984 8.234 8.484 8.734 8.984 9.234 9.484 9.734 9.984 10.484 10.984 11.484 11.984 12.984 13.984 DIN 3771 C/S inch .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 .139 ISO 3601 I.D. mm 98,02 101,19 104,37 107,54 110,72 113,89 117,07 120,24 123,42 126,59 129,77 132,94 136,12 139,29 142,47 145,64 148,82 151,99 158,34 164,69 171,04 177,39 183,74 190,09 196,44 202,79 209,14 215,49 221,84 228,19 234,54 240,89 247,24 253,59 266,29 278,99 291,69 304,39 329,79 355,19 BS 1806 C/S mm 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 3,53 AS 568 PAI Size 1-241 1-242 1-243 1-244 1-245 1-246 1-247 1-248 1-249 1-250 1-251 1-252 1-253 1-254 1-255 1-256 1-257 1-258 1-259 1-260 1-261 1-262 1-263 1-264 1-265 1-266 1-267 1-268 1-269 1-270 1-271 1-272 1-273 1-274 1-275 1-276 1-277 1-278 1-279 1-280 Contact Precision Associates for sizes not listed Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com 21 International O-Ring Standard Cross Reference C0140 C0150 C0140 C0145 C0150 C0155 C0160 C0170 C0180 C0190 C0200 C0206 C0212 C0224 C0160 C0170 C0180 C0190 C0200 18,00 X 3,55 19,00 X 3,55 20,00 X 3,55 C0212 C0224 21,20 X 3,55 22,40 X 3,55 C0236 23,60 X 3,55 C0250 C0258 C0265 25,00 X 3,55 25,80 X 3,55 26,50 X 3,55 C0280 28,00 X 3,55 C0236 C0243 C0250 C0258 C0265 C0273 C0280 C0300 C0315 C0325 C0335 C0345 C0355 C0365 C0375 C0387 C0400 C0412 C0425 C0437 C0450 30,00 X 3,55 31,50 X 3,55 32,50 X 3,55 33,50 X 3,55 34,50 X 3,55 35,50 X 3,55 36,50 X 3,55 37,50 X 3,55 38,70 X 3,55 40,00 X 3,55 41,20 X 3,55 42,50 X 3,55 43,70 X 3,55 45,00 X 3,55 C0300 C0315 C0325 C0335 C0345 C0355 C0365 C0375 C0387 C0400 C0412 C0425 C0437 C0450 SMS-1586 281 282 283 284 BS 4518 -281 JIS B2401 -281 -282 -283 -284 NF T47-501 I.D. inch 14.984 15.955 16.955 17.955 19.960 .551 .571 .591 .610 .620 .669 .709 .748 .787 .811 .835 .882 .906 .929 .957 .984 1.016 1.043 1.075 1.102 1.142 1.181 1.240 1.280 1.319 1.358 1.398 1.437 1.476 1.524 1.575 1.622 1.673 1.720 1.772 DIN 3771 C/S inch .139 .139 .139 .139 .139 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 ISO 3601 I.D. mm 380,59 405,26 430,66 456,06 506,99 14,00 14,50 15,00 15,50 16,00 17,00 18,00 19,00 20,00 20,60 21,20 22,40 23,00 23,60 24,30 25,00 25,80 26,50 27,30 28,00 29,00 30,00 31,50 32,50 33,50 34,50 35,50 36,50 37,50 38,70 40,00 41,20 42,50 43,70 45,00 BS 1806 140-930 C/S mm 3,53 3,53 3,53 3,53 3,53 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 AS 568 PAI Size 1-281 1-282 1-283 1-284 1-286 A A A A A, G A, G A, G G A, G A, G G A, G G A, G A, G A, G G A, G G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G * Mold is cut for non-standard shrink compensation Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 22 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com International O-Ring Standard Cross Reference 46,20 X 3,55 47,50 X 3,55 48,70 X 3,55 50,00 X 3,55 51,50 X 3,55 53,00 X 3,55 54,50 X 3,55 56,00 X 3,55 58,00 X 3,55 60,00 X 3,55 61,50 X 3,55 63,00 X 3,55 65,00 X 3,55 67,00 X 3,55 69,00 X 3,55 71,00 X 3,55 73,00 X 3,55 75,00 X 3,55 77,50 X 3,55 80,00 X 3,55 82,50 X 3,55 85,00 X 3,55 87,50 X 3,55 90,00 X 3,55 92,50 X 3,55 95,00 X 3,55 97,50 X 3,55 100,00 X 3,55 103,00 X 3,55 106,00 X 3,55 109,00 X 3,55 112,00 X 3,55 115,00 X 3,55 118,00 X 3,55 122,00 X 3,55 125,00 X 3,55 128,00 X 3,55 132,00 X 3,55 136,00 X 3,55 140,00 X 3,55 C0462 C0475 C0487 C0500 C0515 C0530 C0545 C0560 C0580 C0600 C0615 C0630 C0650 C0670 C0690 C0710 C0730 C0750 C0775 C0800 C0825 C0850 C0875 C0900 C0925 C0950 C0975 C1000 C1030 C1060 C1090 C1120 C1150 C1180 C1220 C1250 C1280 C1320 C1360 C1400 A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G SMS-1586 JIS B2401 C0462 C0475 C0487 C0500 C0515 C0530 C0545 C0560 C0580 C0600 C0615 C0630 C0650 C0670 C0690 C0710 C0730 C0750 C0775 C0800 C0825 C0850 C0875 C0900 C0925 C0950 C0975 C1000 C1030 C1060 C1090 C1120 C1150 C1180 C1220 C1250 C1280 C1320 C1360 C1400 BS 4518 NF T47-501 I.D. inch 1.819 1.870 1.917 1.969 2.028 2.087 2.146 2.205 2.283 2.362 2.421 2.480 2.559 2.638 2.717 2.795 2.874 2.953 3.051 3.150 3.248 3.346 3.445 3.543 3.642 3.740 3.839 3.937 4.055 4.173 4.291 4.409 4.528 4.646 4.803 4.921 5.039 5.197 5.354 5.512 DIN 3771 C/S inch .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 ISO 3601 140-5.512 I.D. mm 46,20 47,50 48,70 50,00 51,50 53,00 54,50 56,00 58,00 60,00 61,50 63,00 65,00 67,00 69,00 71,00 73,00 75,00 77,50 80,00 82,50 85,00 87,50 90,00 92,50 95,00 97,50 100,00 103,00 106,00 109,00 112,00 115,00 118,00 122,00 125,00 128,00 132,00 136,00 140,00 BS 1806 140-3.248 C/S mm 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 AS 568 PAI Size Contact Precision Associates for sizes not listed Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com 23 International O-Ring Standard Cross Reference C1450 C1500 150,00 X 3,55 C1500 C1550 155,00 X 3,55 C1550 C1600 160,00 X 3,55 C1600 C1650 165,00 X 3,55 C1650 C1700 170,00 X 3,55 C1700 C1750 175,00 X 3,55 C1750 C1800 180,00 X 3,55 C1800 C1850 185,00 X 3,55 C1850 C1900 C1950 C2000 C2120 C2180 C2240 C2300 C2360 C2500 C2580 C2650 C2800 C2900 C3000 C3070 C3150 C3350 C3550 190,00 X 3,55 195,00 X 3,55 200,00 X 3,55 C1900 C1950 C2000 SMS-1586 145,00 X 3,55 BS 4518 C1450 JIS B2401 NF T47-501 I.D. inch 5.610 5.709 5.807 5.906 6.004 6.102 6.201 6.299 6.398 6.496 6.594 6.693 6.791 6.890 6.988 7.087 7.185 7.283 7.382 7.480 7.677 7.874 8.346 8.583 8.819 9.055 9.291 9.843 10.157 10.433 11.024 11.417 11.811 12.087 12.402 13.189 13.976 .571 .925 1.319 DIN 3771 C/S inch .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .140 .157 .157 .157 ISO 3601 I.D. mm 142,50 145,00 147,50 150,00 152,50 155,00 157,50 160,00 162,50 165,00 167,50 170,00 172,50 175,00 177,50 180,00 182,50 185,00 187,50 190,00 195,00 200,00 212,00 218,00 224,00 230,00 236,00 250,00 258,00 265,00 280,00 290,00 300,00 307,00 315,00 335,00 355,00 14,50 23,50 33,50 BS 1806 C/S mm 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 3,55 4,00 4,00 4,00 AS 568 PAI Size G A, G G A, G G A, G G A, G G A, G G A, G G A, G G A, G G A, G G A, G A, G A, G V15 V24 V34 * Mold is cut for non-standard shrink compensation Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 24 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com International O-Ring Standard Cross Reference SMS-1586 D0375 D0387 D0400 D0412 D0425 D0437 D0450 D0462 D0475 D0487 D0500 D0515 D0530 D0545 D0560 D0580 D0600 D0615 D0630 D0650 D0670 D0690 D0710 D0730 D0750 D0775 D0800 D0825 D0850 D0875 D0900 D0925 V40 V55 V70 V85 V100 V120 V150 V175 A A A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G BS 4518 40,00 X 5,30 41,20 X 5,30 42,50 X 5,30 43,70 X 5,30 45,00 X 5,30 46,20 X 5,30 47,50 X 5,30 48,70 X 5,30 50,00 X 5,30 51,50 X 5,30 53,00 X 5,30 54,50 X 5,30 56,00 X 5,30 58,00 X 5,30 60,00 X 5,30 61,50 X 5,30 63,00 X 5,30 65,00 X 5,30 67,00 X 5,30 69,00 X 5,30 71,00 X 5,30 73,00 X 5,30 75,00 X 5,30 77,50 X 5,30 80,00 X 5,30 82,50 X 5,30 85,00 X 5,30 87,50 X 5,30 90,00 X 5,30 92,50 X 5,30 JIS B2401 D0375 D0387 D0400 D0412 D0425 D0437 D0450 D0462 D0475 D0487 D0500 D0515 D0530 D0545 D0560 D0580 D0600 D0615 D0630 D0650 D0670 D0690 D0710 D0730 D0750 D0775 D0800 D0825 D0850 D0875 D0900 D0925 NF T47-501 I.D. inch 1.555 2.146 2.717 3.307 3.898 4.685 5.846 6.811 1.476 1.524 1.575 1.622 1.673 1.720 1.772 1.819 1.870 1.917 1.969 2.028 2.087 2.146 2.205 2.283 2.362 2.421 2.480 2.559 2.638 2.717 2.795 2.874 2.953 3.051 3.150 3.248 3.346 3.445 3.543 3.642 DIN 3771 C/S inch .157 .157 .157 .157 .157 .157 .157 .157 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 ISO 3601 I.D. mm 39,50 54,50 69,00 84,00 99,00 119,00 148,50 173,00 37,50 38,70 40,00 41,20 42,50 43,70 45,00 46,20 47,50 48,70 50,00 51,50 53,00 54,50 56,00 58,00 60,00 61,50 63,00 65,00 67,00 69,00 71,00 73,00 75,00 77,50 80,00 82,50 85,00 87,50 90,00 92,50 BS 1806 C/S mm 4,00 4,00 4,00 4,00 4,00 4,00 4,00 4,00 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 AS 568 PAI Size Contact Precision Associates for sizes not listed Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com 25 International O-Ring Standard Cross Reference D0950 D0975 D1000 D1030 D1060 D1090 D1120 D1150 D1180 D1220 D1250 D1280 D1320 D1360 D1400 D1450 145,00 X 5,30 D1450 D1500 150,00 X 5,30 D1500 D1550 155,00 X 5,30 D1550 D1600 160,00 X 5,30 D1600 D1650 165,00 X 5,30 D1650 D1700 170,00 X 5,30 D1750 175,00 X 5,30 D1800 180,00 X 5,30 D1850 185,00 X 5,30 D1900 D1950 D2000 190,00 X 5,30 195,00 X 5,30 200,00 X 5,30 D1700 D1725 D1750 D1775 D1800 D1825 D1850 D1875 D1900 D1950 D2000 D2030 D2060 D2120 206,00 X 5,30 212,00 X 5,30 SMS-1586 95,00 X 5,30 97,50 X 5,30 100,00 X 5,30 103,00 X 5,30 106,00 X 5,30 109,00 X 5,30 112,00 X 5,30 115,00 X 5,30 118,00 X 5,30 122,00 X 5,30 125,00 X 5,30 128,00 X 5,30 132,00 X 5,30 136,00 X 5,30 140,00 X 5,30 BS 4518 D0950 D0975 D1000 D1030 D1060 D1090 D1120 D1150 D1180 D1220 D1250 D1280 D1320 D1360 D1400 JIS B2401 NF T47-501 I.D. inch 3.740 3.829 3.937 4.055 4.173 4.291 4.409 4.528 4.646 4.803 4.921 5.039 5.197 5.354 5.512 5.610 5.709 5.807 5.906 6.004 6.102 6.201 6.299 6.398 6.496 6.594 6.693 6.791 6.890 6.988 7.087 7.185 7.283 7.382 7.480 7.677 7.874 7.992 8.110 8.346 DIN 3771 C/S inch .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 ISO 3601 I.D. mm 95,00 97,50 100,00 103,00 106,00 109,00 112,00 115,00 118,00 122,00 125,00 128,00 132,00 136,00 140,00 142,50 145,00 147,50 150,00 152,50 155,00 157,50 160,00 162,50 165,00 167,50 170,00 172,50 175,00 177,50 180,00 182,50 185,00 187,50 190,00 195,00 200,00 203,00 206,00 212,00 BS 1806 C/S mm 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 AS 568 PAI Size A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G G A, G G A, G G A, G G A, G G A, G G A, G G A, G G A, G G A, G G A, G A, G A, G G A, G A, G * Mold is cut for non-standard shrink compensation Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 26 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com International O-Ring Standard Cross Reference 230,00 X 5,30 236,00 X 5,30 D2300 D2360 D2390 D2430 D2500 D2540 D2580 D2610 D2650 D2680 D2720 D2760 D2800 D2830 D2860 D2900 D2950 D3000 D3030 D3070 D3110 D3150 D3200 D3250 D3300 D3350 D3400 D3450 D3500 D3550 D3600 D3650 D3700 D3750 D3790 D3830 D3870 243,00 X 5,30 250,00 X 5,30 258,00 X 5,30 265,00 X 5,30 272,00 X 5,30 280,00 X 5,30 290,00 X 5,30 300,00 X 5,30 307,00 X 5,30 315,00 X 5,30 325,00 X 5,30 335,00 X 5,30 345,00 X 5,30 355,00 X 5,30 365,00 X 5,30 375,00 X 5,30 387,00 X 5,30 SMS-1586 D2180 D2240 BS 4518 218,00 X 5,30 224,00 X 5,30 JIS B2401 NF T47-501 I.D. inch 8.583 8.819 8.937 9.055 9.291 9.409 9.567 9.843 10.000 10.157 10.276 10.433 10.551 10.709 10.866 11.024 11.142 11.260 11.417 11.614 11.811 11.929 12.087 12.244 12.402 12.598 12.795 12.992 13.189 13.386 13.583 13.780 13.976 14.173 14.370 14.567 14.764 14.921 15.079 15.236 DIN 3771 C/S inch .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 .209 ISO 3601 I.D. mm 218,00 224,00 227,00 230,00 236,00 239,00 243,00 250,00 254,00 258,00 261,00 265,00 268,00 272,00 276,00 280,00 283,00 286,00 290,00 295,00 300,00 303,00 307,00 311,00 315,00 320,00 325,00 330,00 335,00 340,00 345,00 350,00 355,00 360,00 365,00 370,00 375,00 379,00 383,00 387,00 BS 1806 C/S mm 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 5,30 AS 568 PAI Size A, G A, G G A, G A, G G A, G A, G G A, G G A, G G A, G G A, G G G A, G G A, G G A, G G A, G G A, G G A, G G A, G G A, G G A, G G A, G G G A, G Contact Precision Associates for sizes not listed Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com 27 International O-Ring Standard Cross Reference JIS B2401 G G A, G SMS-1586 NF T47-501 400,00 X 5,30 D3910 D3950 D4000 BS 4518 DIN 3771 1-339 1-340 1-341 -309 -310 -311 -312 -313 -314 -315 -316 -317 -318 -319 -320 -321 -322 -323 -324 -325 -326 -327 -328 -329 -330 -331 -332 -333 -334 -335 -336 -619 -337 -338 -620 -339 -340 -341 -621 ISO 3601 1-337 1-338 C/S I.D. inch inch .209 15.394 .209 15.551 .209 15.748 .210 .350 .210 .412 -309 .210 .475 -310 .210 .537 -311 .210 .600 -312 .210 .662 -313 .210 .725 -314 .210 .787 -315 .210 .850 -316 .210 .912 -317 .210 .975 -318 .210 1.037 -319 .210 1.100 -320 .210 1.162 -321 .210 1.225 -322 .210 1.287 -323 .210 1.350 -324 .210 1.475 -325 .210 1.600 -326 .210 1.725 -327 .210 1.850 -328 .210 1.975 -329 .210 2.100 -330 .210 2.225 -331 .210 2.350 -332 .210 2.475 -333 .210 2.600 -334 .210 2.725 -335 .210 2.850 -336 .210 2.938 .210 2.975 -337 .210 3.100 -338 .210 3.141 .210 3.225 -339 .210 3.350 -340 .210 3.475 -341 .210 3.531 BS 1806 1-308 1-309 1-310 1-311 1-312 1-313 1-314 1-315 1-316 1-317 1-318 1-319 1-320 1-321 1-322 1-323 1-324 1-325 1-326 1-327 1-328 1-329 1-330 1-331 1-332 1-333 1-334 1-335 1-336 C/S I.D. mm mm 5,30 391,00 5,30 395,00 5,30 400,00 5,33 8,89 5,33 10,46 5,33 12,07 5,33 13,64 5,33 15,24 5,33 16,81 5,33 18,42 5,33 19,99 5,33 21,59 5,33 23,16 5,33 24,77 5.33 26,34 5,33 27,94 5,33 29,51 5,33 31,12 5,33 32,69 5,33 34,29 5,33 37,47 5,33 40,64 5.33 43,82 5,33 46,99 5,33 50,17 5,33 53,34 5,33 56,52 5,33 59,69 5,33 62,87 5,33 66,04 5.33 69,22 5,33 72,39 5,33 74,61 5,33 75,57 5,33 78,74 5,33 79,78 5,33 81,92 5,33 85,09 5.33 88,27 5,33 89,69 AS 568 PAI Size 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 * Mold is cut for non-standard shrink compensation Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 28 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com International O-Ring Standard Cross Reference 1-356 1-357 1-358 1-359 1-360 1-361 1-362 210-6.350 1-363 1-364 -351 -352 -353 -354 -355 -356 -357 -358 -359 -360 -361 -362 -363 -364 SMS-1586 1-355 -348 -349 -350 342 343 344 BS 4518 1-354 -345 -346 -347 -342 -343 -344 -622 -345 -346 -347 -623 -348 -349 -350 -860 -351 -861 -352 -862 -353 -863 -354 -864 -355 -865 -356 -866 -357 -867 -358 -868 -359 -869 -360 -870 -361 -644 -362 -645 -363 -646 -364 -647 JIS B2401 1-353 -342 -343 -344 NF T47-501 1-352 I.D. inch 3.600 3.725 3.850 3.937 3.975 4.100 4.225 4.313 4.350 4.475 4.600 4.625 4.725 4.750 4.850 4.875 4.975 5.000 5.100 5.125 5.225 5.250 5.350 5.375 5.475 5.500 5.600 5.625 5.725 5.750 5.850 5.875 5.975 6.100 6.225 6.350 6.475 6.600 6.725 6.850 DIN 3771 1-351 C/S inch .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 ISO 3601 1-348 1-349 1-350 I.D. mm 91,44 94,62 97,79 100,00 100,97 104,14 107,32 109,54 110,49 113,67 116,84 117,48 120,02 120,65 123,19 123,83 126,37 127,00 129,54 130,18 132,72 133,35 135,89 136,53 139,07 139,70 142,24 142,88 145,42 146,05 148,59 149,23 151,77 154,94 158,12 161,29 164,47 167,64 170,82 173,99 BS 1806 1-345 1-346 1-347 C/S mm 5,33 5,33 5,33 5,33 5,33 5,33 5.33 5,33 5,33 5,33 5,33 5,33 5,33 5,33 5.33 5,33 5,33 5,33 5,33 5,33 5,33 5,33 5.33 5,33 5,33 5,33 5,33 5,33 5,33 5,33 5.33 5,33 5,33 5,33 5,33 5,33 5,33 5,33 5.33 5,33 AS 568 PAI Size 1-342 1-343 1-344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 Contact Precision Associates for sizes not listed Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com 29 International O-Ring Standard Cross Reference SMS-1586 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 BS 4518 -365 -366 -367 -368 -369 -370 -371 -372 -373 -374 -375 -376 -377 -378 -379 -380 -381 -382 -383 -384 -385 -386 -387 -388 -389 -390 -391 -392 -393 -394 -395 JIS B2401 -365 -366 -367 -368 -369 -370 -371 -372 -373 -374 -375 -376 -377 -378 -379 -380 -381 -382 -383 -384 -385 -386 -387 -388 -389 -390 -391 -392 -393 -394 -395 NF T47-501 I.D. inch 6.975 7.225 7.475 7.725 7.975 8.225 8.475 8.725 8.975 9.225 9.475 9.725 9.975 10.475 10.975 11.475 11.975 12.975 13.975 14.975 15.955 16.955 17.955 18.955 19.955 20.955 21.955 22.940 23.940 24.940 25.940 26.965 1.740 1.744 1.783 1.874 1.937 1.941 1.953 2.031 DIN 3771 C/S inch .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .210 .224 .224 .224 .224 .224 .224 .224 .224 ISO 3601 I.D. mm 177,17 183,52 189,87 196,22 202,57 208,92 215,27 221,62 227,97 234,32 240,67 247,02 253,37 266,07 278,77 291,47 304,17 329,57 354,97 380,37 405,26 430,66 456,06 481,46 506,86 532,26 557,66 582,68 608,08 633,48 658,88 684,91 44,20 44,30 45,30 47,60 49,20 49,30 49,60 51,60 BS 1806 * 224-1.941VS C/S mm 5,33 5,33 5,33 5,33 5,33 5,33 5.33 5,33 5,33 5,33 5,33 5,33 5,33 5,33 5.33 5,33 5,33 5,33 5,33 5,33 5,33 5,33 5.33 5,33 5,33 5,33 5,33 5,33 5,33 5,33 5.33 5,33 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 AS 568 PAI Size 1-365 1-366 1-367 1-368 1-369 1-370 1-371 1-372 1-373 1-374 1-375 1-376 1-377 1-378 1-379 1-380 1-381 1-382 1-383 1-384 1-385 1-386 1-387 1-388 1-389 1-390 1-391 1-392 1-393 1-394 1-395 1-396 D 0443-57 0453-57 P48A D 0493-57 P50A P52 * Mold is cut for non-standard shrink compensation Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 30 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com International O-Ring Standard Cross Reference SMS-1586 BS 4518 JIS B2401 NF T47-501 I.D. inch 2.059 2.071 2.134 2.138 2.150 2.177 2.189 2.268 2.331 2.335 2.346 2.425 2.453 2.465 2.528 2.531 2.543 2.622 2.724 2.728 2.740 2.780 2.921 2.925 2.937 3.118 3.122 3.134 3.311 3.319 3.331 3.508 3.516 3.528 3.705 3.713 3.724 3.902 3.909 3.921 DIN 3771 C/S inch .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 ISO 3601 224-3.724 I.D. mm 52,30 52,60 54,20 54,30 54,60 55,30 55,60 57,60 59,20 59,30 59,60 61,60 62,30 62,60 64,20 64,30 64,60 66,60 69,20 69,30 69,60 70,60 74,20 74,30 74,60 79,20 79,30 79,60 84,10 84,30 84,60 89,10 89,30 89,60 94,10 94,30 94,60 99,10 99,30 99,60 BS 1806 224-2.925 C/S mm 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 AS 568 PAI Size 0523-57 P53 D 0543-57 P55 0553-57 P56 P58 D 0593-57 P60 P62 0623-57 P63 D 0643-57 P65 P67 D 0693-57 P70 P71 D 0743-57 P75 D 0793-57 P80 D 0843-57 P85 D 0893-57 P90 D 0943-57 P95 D 0993-57 P100 Contact Precision Associates for sizes not listed Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com 31 International O-Ring Standard Cross Reference SMS-1586 BS 4518 JIS B2401 NF T47-501 I.D. inch 4.000 4.098 4.106 4.118 4.295 4.303 4.315 4.394 4.500 4.512 4.697 4.709 4.894 4.906 5.091 5.102 5.181 5.287 5.299 5.484 5.496 5.681 5.693 5.878 5.890 6.075 6.272 6.468 6.665 6.862 7.059 7.256 7.453 7.650 7.846 8.240 8.634 9.028 9.421 9.815 DIN 3771 224-8.240 C/S inch .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 ISO 3601 224-6.075 I.D. mm 101,60 104,10 104,30 104,60 109,10 109,30 109,60 111,60 114,30 114,60 119,30 119,60 124,30 124,60 129,30 129,60 131,60 134,30 134,60 139,30 139,60 144,30 144,60 149,30 149,60 154,30 159,30 164,30 169,30 174,30 179,30 184,30 189,30 194,30 199,30 209,30 219,30 229,30 239,30 249,30 BS 1806 224-4.098 C/S mm 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 AS 568 PAI Size P102 D 1043-57 P105 D 1093-57 P110 P112 1143-57 D 1193-57 D 1243-57 D 1293-57 D 1343-57 D 1393-57 D 1443-57 D 1493-57 S 1543-57 1593-57 1643-57 1693-57 1743-57 1793-57 1843-57 1893-57 1943-57 1993-57 2093-57 2193-57 2293-57 2393-57 2493-57 S S S S S S S S S S S S S S S P115 P120 P125 P130 P132 P135 P140 P145 G150 P150 G155 G160 G165 G170 G175 G180 G185 G190 G195 G200 G210 G220 G230 G240 G250 * Mold is cut for non-standard shrink compensation Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 32 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com International O-Ring Standard Cross Reference 2593-57 2693-57 2793-57 2893-57 2993-57 3093-57 3193-57 3393-57 3593-57 3793-57 3893-57 3993-57 4193-57 4393-57 4593-57 4793-57 4893-57 4993-57 SMS-1586 G260 G270 G280 G290 G300 BS 4518 JIS B2401 NF T47-501 I.D. inch 10.210 10.600 11.000 11.390 11.783 12.177 12.571 13.358 14.146 14.933 15.327 15.720 16.508 17.295 18.083 18.870 19.264 19.657 8.760 10.709 12.657 14.803 16.752 1.350 1.475 1.600 1.725 1.850 1.975 2.100 2.225 2.350 2.475 2.600 2.725 2.850 2.975 3.100 3.225 3.350 DIN 3771 C/S inch .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .236 .236 .236 .236 .236 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 ISO 3601 1-400 1-401 1-402 1-403 1-404 1-405 1-406 1-407 1-408 1-409 1-410 1-411 1-412 1-413 1-414 1-415 1-416 I.D. mm 259,30 269,30 279,30 289,30 299,30 309,30 319,30 339,30 359,30 379,30 389,30 399,30 419,30 439,30 459,30 479,30 489,30 499,30 222,50 272,00 321,50 376,00 425,50 34,29 37,47 40,64 43,82 46,99 50,17 53,34 56,52 59,69 62,87 66,04 69,22 72,39 75,57 78,74 81,92 85,09 BS 1806 224-14.146 C/S mm 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 5,70 6,00 6,00 6,00 6,00 6,00 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 AS 568 PAI Size S S S S S S S S S S S S S S S V225 V275 V325 V380 V430 Contact Precision Associates for sizes not listed Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com 33 International O-Ring Standard Cross Reference 1-442 1-443 1-444 -432 -433 -434 -435 -436 -437 -438 -439 -440 -441 -442 -443 -444 SMS-1586 1-441 -429 -430 -431 425 BS 4518 1-440 -426 -427 -428 -425 -624 -426 -427 -428 -625 -429 -430 -431 -626 -432 -433 -434 -435 -436 -437 -872 -438 -627 -874 -439 -628 -876 -440 -878 -441 -880 -442 -882 -443 -884 -444 JIS B2401 1-439 -425 NF T47-501 1-438 I.D. inch 3.475 3.600 3.725 3.850 3.975 4.100 4.225 4.350 4.475 4.516 4.600 4.725 4.850 4.906 4.975 5.100 5.225 5.297 5.350 5.475 5.600 5.725 5.850 5.975 6.125 6.225 6.281 6.375 6.475 6.563 6.625 6.725 6.875 6.975 7.125 7.225 7.375 7.475 7.625 7.725 DIN 3771 1-432 1-433 1-434 1-435 1-436 1-437 C/S inch .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 ISO 3601 1-429 1-430 1-431 I.D. mm 88,27 91,44 94,62 97,79 100,97 104,14 107,32 110,49 113,67 114,71 116,84 120,02 123,19 124,61 126,37 129,54 132,72 134,54 135,89 139,07 142,24 145,42 148,59 151,77 155,58 158,12 159,54 161,93 164,47 166,70 168,28 170,82 174,63 177,17 180,98 183,52 187,33 189,87 193,68 196,22 BS 1806 1-426 1-427 1-428 C/S mm 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 AS 568 PAI Size 1-417 1-418 1-419 1-420 1-421 1-422 1-423 1-424 1-425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 * Mold is cut for non-standard shrink compensation Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 34 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com International O-Ring Standard Cross Reference 1-455 1-456 1-457 1-458 1-459 1-460 1-461 1-462 1-463 1-464 1-465 1-466 1-467 1-468 1-469 1-470 1-471 1-472 -448 -449 -450 -451 -452 -453 -454 -455 -456 -457 -458 -459 -460 -461 -462 -463 -464 -465 -466 -467 -468 -469 -470 -471 -472 SMS-1586 1-454 -447 BS 4518 1-453 -446 JIS B2401 1-452 -445 -886 -445 -445A -446 -446A -447 -447A -448 -448A -449 -449A -450 -450A -451 -451A -452 -452A -453 -648 -454 -649 -455 -650 -456 -457 -458 -459 -460 -461 -462 -463 -464 -465 -466 -467 -468 -469 -470 -471 -472 NF T47-501 1-450 275-10.725 1-451 I.D. inch 7.875 7.975 8.225 8.475 8.725 8.975 9.225 9.475 9.725 9.975 10.225 10.475 10.725 10.975 11.225 11.475 11.725 11.975 12.225 12.475 12.725 12.975 13.225 13.475 13.975 14.475 14.975 15.475 15.955 16.455 16.955 17.455 17.955 18.455 18.955 19.455 19.955 20.955 21.955 22.940 DIN 3771 1-449 C/S inch .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 .275 ISO 3601 1-448 I.D. mm 200,03 202,57 208,92 215,27 221,62 227,97 234,32 240,67 247,02 253,37 259,72 266,07 272,42 278,77 285,12 291,47 297,82 304,17 310,52 316,87 323,22 329,57 335,92 342,27 354,97 367,67 380,37 393,07 405,26 417,96 430,66 443,36 456,06 468,76 481,46 494,16 506,86 532,26 557,66 582,68 BS 1806 1-445 275-8.225 1-446 275-8.275 1-447 C/S mm 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 6,99 AS 568 PAI Size 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 Contact Precision Associates for sizes not listed Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com 35 International O-Ring Standard Cross Reference E1090 E1120 E1150 E1180 E1220 E1250 E1280 E1320 E1360 E1400 E1450 E1450 E1500 E1500 E1550 E1550 E1600 E1600 E1650 E1650 E1700 E1700 E1725 E1750 E1775 E1800 E1825 E1850 E1875 E1900 E1950 E2000 E2030 E2060 E2120 E2180 E1750 E1800 E1850 E1900 E1950 E2000 E2060 E2120 E2180 206,00 X 7,00 212,00 X 7,00 218,00 X 7,00 SMS-1586 E1090 E1120 E1150 E1180 E1220 E1250 E1280 E1320 E1360 E1400 BS 4518 473 474 475 JIS B2401 -473 -474 -475 NF T47-501 I.D. inch 23.940 -473 24.940 -474 25.940 -475 26.955 4.291 4.409 4.528 4.646 4.803 4.921 5.039 5.197 5.354 5.512 5.610 5.709 5.807 5.906 6.004 6.102 6.201 6.299 6.398 6.496 6.594 6.693 6.791 6.890 6.988 7.087 7.185 7.283 7.382 7.480 7.677 7.874 7.992 8.110 8.346 8.583 DIN 3771 C/S inch .275 .275 .275 .275 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 ISO 3601 I.D. mm 608,08 633,48 658,88 684,66 109,00 112,00 115,00 118,00 122,00 125,00 128,00 132,00 136,00 140,00 142,50 145,00 147,50 150,00 152,50 155,00 157,50 160,00 162,50 165,00 167,50 170,00 172,50 175,00 177,50 180,00 182,50 185,00 185,70 190,00 195,00 200,00 203,00 206,00 212,00 218,00 BS 1806 C/S mm 6,99 6,99 6,99 6,99 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 AS 568 PAI Size 1-473 1-474 1-475 1-476 A, G A, G A, G A, G A, G A, G A, G A, G A, G A, G G A, G G A, G G A, G G A, G G A, G G A, G G A, G G A, G G A, G G A, G A, G A, G G A, G A, G A, G * Mold is cut for non-standard shrink compensation Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 36 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com International O-Ring Standard Cross Reference E2240 E2300 E2360 230,00 X 7,00 236,00 X 7,00 E2430 E2500 243,00 X 7,00 250,00 X 7,00 E2580 258,00 X 7,00 E2650 265,00 X 7,00 E2720 272,00 X 7,00 E2800 280,00 X 7,00 E2900 290,00 X 7,00 E3000 300,00 X 7,00 E3070 307,00 X 7,00 E3150 315,00 X 7,00 E3250 325,00 X 7,00 E3350 335,00 X 7,00 E3450 345,00 X 7,00 E3550 355,00 X 7,00 E3650 365,00 X 7,00 E3750 375,00 X 7,00 E3870 387,00 X 7,00 E2300 E2360 E2390 E2430 E2500 E2540 E2580 E2610 E2650 E2680 E2720 E2760 E2800 E2830 E2860 E2900 E2950 E3000 E3030 E3070 E3110 E3150 E3200 E3250 E3300 E3350 E3400 E3450 E3500 E3550 E3600 E3650 E3700 E3750 E3790 E3830 E3870 E3910 SMS-1586 224,00 X 7,00 BS 4518 E2240 JIS B2401 NF T47-501 I.D. inch 8.819 8.937 9.055 9.291 9.409 9.567 9.843 10.000 10.157 10.276 10.433 10.551 10.709 10.866 11.024 11.142 11.260 11.417 11.614 11.811 11.929 12.087 12.244 12.402 12.598 12.795 12.992 13.189 13.386 13.583 13.780 13.976 14.173 14.370 14.567 14.764 14.921 15.079 15.236 15.394 DIN 3771 C/S inch .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 ISO 3601 I.D. mm 224,00 227,00 230,00 236,00 239,00 243,00 250,00 254,00 258,00 261,00 265,00 268,00 272,00 276,00 280,00 283,00 286,00 290,00 295,00 300,00 303,00 307,00 311,00 315,00 320,00 325,00 330,00 335,00 340,00 345,00 350,00 355,00 360,00 365,00 370,00 375,00 379,00 383,00 387,00 391,00 BS 1806 C/S mm 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 AS 568 PAI Size A, G G A, G A, G G A, G A, G G A, G G A, G G A, G G A, G G G A, G G A, G G A, G G A, G G A, G G A, G G A, G G A, G G A, G G A, G G G A, G G Contact Precision Associates for sizes not listed Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com 37 International O-Ring Standard Cross Reference 425,00 X 7,00 437,00 X 7,00 450,00 X 7,00 462,00 X 7,00 475,00 X 7,00 487,00 X 7,00 500,00 X 7,00 515,00 X 7,00 530,00 X 7,00 545,00 X 7,00 560,00 X 7,00 580,00 X 7,00 600,00 X 7,00 615,00 X 7,00 630,00 X 7,00 650,00 X 7,00 G A, G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G SMS-1586 412,00 X 7,00 E3950 E4000 E4060 E4120 E4180 E4250 E4290 E4330 E4370 E4430 E4500 E4560 E4620 E4660 E4700 E4750 E4790 E4830 E4870 E4930 E5000 E5080 E5150 E5230 E5300 E5380 E5450 E5530 E5600 E5700 E5800 E5900 E6000 E6080 E6150 E6230 E6300 E6400 E6500 E6600 BS 4518 400,00 X 7,00 JIS B2401 E4000 NF T47-501 I.D. inch 15.551 15.748 15.984 16.220 16.457 16.732 16.890 17.047 17.205 17.441 17.717 17.953 18.189 18.346 18.504 18.701 18.858 19.016 19.173 19.409 19.685 20.000 20.276 20.591 20.866 21.181 21.457 21.772 22.047 22.441 22.835 23.228 23.622 23.937 24.213 24.528 24.803 25.197 25.591 25.984 DIN 3771 C/S inch .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 .276 ISO 3601 I.D. mm 395,00 400,00 406,00 412,00 418,00 425,00 429,00 433,00 437,00 443,00 450,00 456,00 462,00 466,00 470,00 475,00 479,00 483,00 487,00 493,00 500,00 508,00 515,00 523,00 530,00 538,00 545,00 553,00 560,00 570,00 580,00 590,00 600,00 608,00 615,00 623,00 630,00 640,00 650,00 660,00 BS 1806 C/S mm 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 7,00 AS 568 PAI Size * Mold is cut for non-standard shrink compensation Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 38 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com International O-Ring Standard Cross Reference BS 4518 SMS-1586 670,00 X 7,00 E6700 JIS B2401 NF T47-501 DIN 3771 C/S I.D. inch inch .276 26.378 .331 5.673 .331 5.870 .331 5.886 .331 6.067 .331 6.083 .331 6.264 .331 6.280 .331 6.461 .331 6.476 .331 6.657 .331 6.673 .331 6.854 .331 6.870 .331 7.051 .331 7.067 .331 7.248 .331 7.264 .331 7.445 .331 7.461 .331 7.642 .331 7.657 .331 7.839 .331 7.854 .331 8.035 .331 8.051 .331 8.209 .331 8.232 .331 8.248 .331 8.445 .331 8.626 .331 8.642 .331 8.839 .331 9.020 .331 9.035 .331 9.217 .331 9.232 .331 9.413 .331 9.429 .331 9.626 ISO 3601 I.D. mm 670,00 144,10 149,10 149,50 154,10 154,50 159,10 159,50 164,10 164,50 169,10 169,50 174,10 174,50 179,10 179,50 184,10 184,50 189,10 189,50 194,10 194,50 199,10 199,50 204,10 204,50 208,50 209,10 209,50 214,50 219,10 219,50 224,50 229,10 229,50 234,10 234,50 239,10 239,50 244,50 BS 1806 C/S mm 7,00 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 8,40 AS 568 PAI Size 1441-84 1491-84 D D 1541-84 D 1591-84 D 1641-84 D 1691-84 D 1741-84 D 1791-84 D 1841-84 D 1891-84 D 1941-84 D 1991-84 D G P150 P155 P160 P165 P170 P175 P180 P185 P190 P195 P200 2041-84 P205 P209 2091-84 D 2191-84 D 2291-84 D P210 P215 P220 P225 P230 2341-84 P235 2391-84 D P240 P245 Contact Precision Associates for sizes not listed Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com 39 International O-Ring Standard Cross Reference SMS-1586 BS 4518 JIS B2401 NF T47-501 DIN 3771 I.D. inch 9.807 9.823 10.020 10.217 10.413 10.610 10.807 11.004 11.201 11.398 11.594 11.791 12.382 12.579 13.169 13.366 13.957 14.154 14.744 15.138 15.728 18.701 20.650 22.795 24.941 26.890 28.839 30.787 32.933 37.027 41.102 ISO 3601 C/S inch .331 .331 .331 .331 .331 .331 .331 .331 .331 .331 .331 .331 .331 .331 .331 .331 .331 .331 .331 .331 .331 .394 .394 .394 .394 .394 .394 .394 .394 .394 .394 BS 1806 C/S I.D. mm mm 8,40 249,10 8,40 249,50 8,40 254,50 8,40 259,50 8,40 264,50 8,40 269,50 8,40 274,50 8,40 279,50 8,40 284,50 8,40 289,50 8,40 294,50 8,40 299,50 8,40 314,50 8,40 319,50 8,40 334,50 8,40 339,50 8,40 354,50 8,40 359,50 8,40 374,50 8,40 384,50 8,40 399,50 10,00 475,00 10,00 524,50 10,00 579,00 10,00 633,50 10,00 683,00 10,00 732,50 10,00 782,00 10,00 836,50 10,00 940,50 10,00 1044,00 AS 568 PAI Size 2491-84 D P250 P255 P260 P265 P270 P275 P280 P285 P290 P295 P300 P315 P320 P335 P340 P355 P360 P375 P385 P400 V480 V530 V585 V640 V690 V740 V790 V845 V950 V1055 * Mold is cut for non-standard shrink compensation Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 40 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com International O-Ring Standard Cross Reference ISO 6149 Metric Tube Fitting O-Rings PAI Size C/S mm I.D. mm C/S inch I.D. inch Thread Size 63-240 1,60 6,10 .063 .240 M8 x 1 63-319 1,60 8,10 .063 .319 M10 x 1 87-366 2,20 9,30 .087 .366 M12 x 1.5 87-445 2,20 11,30 .087 .445 M14 x 1.5 87-524 2,20 13,30 .087 .524 M16 x 1.5 87-602 2,20 15,30 .087 .602 M18 x 1.5 87-681 2,20 17,30 .087 .681 M20 x 1.5 87-760 2,20 19,30 .087 .760 M22 x 1.5 114-929 2,90 23,60 .114 .929 M27 x 2 114-1.165 2,90 29,60 .114 1.165 M33 x 2 114-1.520 2,90 38,60 .114 1.520 M42 x 2 114-1.756 2,90 44,60 .114 1.756 M48 x 2 114-2.228 2,90 56,60 .114 2.228 M60 x 2 Contact Precision Associates for sizes not listed Precision Associates, Inc. 3800 N. Washington Ave. Minneapolis, MN 55412 Phone: (612) 333-7464 Fax: (612) 342-2417 Toll: (800) 394-6590 www.PrecisionAssoc.com 41 Toll Free: 1-800-394-6590 612-333-7464 Sales: 612-334-9190 3800 North Washington Ave. Minneapolis, MN 55412-2142 FAX: 612-342-2417 info@PrecisionAssoc.com Ask us about our complete line of product literature: Standard O-Rings Special Size O-Rings U-Cups V-Rings Rod Wipers X-Rings 8-Rings™ Multiseal® Low Friction Seals Kurv-Bak™ Hard Rubber Backup Rings Rubber Balls Medical Seals Custom Moldings After 57 years in the rubber business, we’ve learned to be flexible. We’ll bend over backwards to design custom solutions that meet your needs precisely. PAI is the company you can trust for rubber seal solutions YOUR WAY! ● Over 1,000 different compounds ● Custom Molding ● More than 2,400 O-Ring Sizes ● 99% on-time delivery ● On-site Mold Shop ● ISO 14644-1 Class 7 Clean Room Copyright© 2010, 2012 Precision Associates, Inc. D20C25f www.PrecisionAssoc.com