Intelligent Software and Metering Devices
Power
Management
Software
WinPM.Net ™
Application Features:
Web-Enabled
Power Quality Analysis
Data Acquisition
Custom Graphics
OPC
SQL Database
Alarm Notification
Database Management
Load Reporting
ACCESS
Energy Manager
Application Features:
Sub-Billing Management
Custom Billing Templates
Variable Rate
Configurations
Commercial/Industrial Use
Web-Enabled
Alarm Notification
SQL Database
Custom Graphics
Meter Panels
Application Features:
Factory Pre-wired
1 to 12 meter options
Key-lock Door available
Communication available
POWER, ENERGY and DEMAND
Voltage/current: per phase, average
Voltage/current: unbalance
Power: real, reactive, apparent, power factor,
frequency kW/kV
Energy: bi-directional, import, export
Energy: total, net
Demand: block, sliding window
Demand: thermal predicted
POWER QUALITY ANALYSIS
Sag/swell monitoring
Symmetrical components: zero, negative, positive
Transient detection, microseconds
Harmonics (individual, even, odd, total) up to
Sampling rate, maximum samples/cycle
Flicker, harmonics to EN50160, IEC 6100-4-7 / 4-15
Configurable for IEEE 519-1992, IEEE 1159, SEMI/ITIC
“Number of nines” uptime data (3 nines=99.9%)
DATA and WAVEFORM LOGS
Triggered by setpoint, schedule, or external signal
Sequence-of-event logs, variable log depth
Minimum/maximum logs
Historical logs, maximum # of channels
Waveform logs, maximum # of consecutive cycles
Time-stamps, resolution in seconds
Event Log
GPS time synchronization
COMMUNICATION PORTS and I/O
( ) = Optional
RS-232/485 ports
RS-485-only ports
Ethernet ports
Infrared optical ports
PROFIBUS ports
Built-in modems
Modbus RTU Slave on serial, modem or infrared ports
(If equipped with modem or infrared port)
Modbus RTU Master on serial ports
Modbus/TCP on Ethernet ports
DNP 3.0 on serial, modem, infrared ports
EtherGate™: 31 other meters accessible via RS-485
ModemGate: 31 other meters accessible via RS-485
MeterM@il®: data e-mailed from meter
WebMeter®: on-board web server
XML
Analog inputs
Analog outputs
Digital status/counter inputs (standard/optional add-ons)
Digital relay outputs (control/pulse)
SETPOINTS, ALARMING and CONTROL
Setpoints, minimum response time
Math, logic, trig, log, linearization formulas
Single- and multi-condition alarms
Call-out on alarm
REVENUE METERING
ANSI C12.16 accuracy compliant
ANSI C12.20 0.2 compliant
EN50160
IEC 60687 0.2S compliant
IEC 60687 accuracy class 0.5S compliant
ANSI class 10 (5A nominal, 10A max)
ANSI class 2, IEC 1/10 (1A nominal, 10A max)
ANSI class 20, IEC 5/20 (5A nominal, 20A max)
MV-90 on serial; Ethernet ports
Time-of-use
Transformer/line loss compensation
PAC 3200
9200
9330
9340
9350
9360
THD only
400+
THD only
64
15th
32
63rd
128/3
9510 ADR
9510
9610/9610H
31st
64
63rd
128/185
63rd
256
65/17
127th/256th
512/1024
800
96
0.001
800
96
0.001
1
1
(1)
1
1
1
(1)
1
1
1
(1)
1
(1)
(1)
(1)
1 sec
(1)
1
1
2/32
1
0.001
2
(1)
1
1
(1)
6/96
48
0.001
2
(1)
1
3
up to 185
0.1
1
(1)
800
(1)
(1)
(1)
1
1
2
and/or, ><
0.5S
(4)
(4)
4
4
(1)
(2)
(2)
1/(6)
1/(2)
(4)
(4)
4
4
(2)
(2)
1/(6)
1/(2)
1 sec
1 sec
0.5S
0.5S
0.5S
(4)
(4)
8/8
7
(4)
(4)
8/8
7
(4)
(4)
8/8
7
¹⁄₂ cycle
¹⁄₂ cycle
¹⁄₂ cycle
0.2S
0.2S
Some features are optional. Refer to datasheets for allowable port configurations. Products meet or exceed the accuracy requirements of the standards listed; due to form factors, not all ANSI/IEC compliance tests may apply. Some products certified by third-party laboratory.
Siemens Energy & Automation, Inc.
3333 Old Milton Parkway
Alpharetta, GA 30005
1-800-964-4114
info.sea@siemens.com
ACCESS Technical Support
1-800-427-2256
www.sea.siemens.com/access
© 2008 Siemens Energy & Automation, Inc. All Rights Reserved. Siemens is a registered trademark of Siemens AG. ACCESS and WinPM.Net are trademarks of Siemens Energy & Automation, Inc.
Product names mentioned may be trademarks or registered trademarks of their respective companies. Specifications are subject to change without notice.
Order # PMPB-POST1-0208 2.5C0208CW Printed in USA