CD-LFM20-01
PRODUCT OVERVIEW
LFM-20
Product
Description
Isolated Contact Fixture Module
The Evolve Isolated Contact Fixture Module is a component of the Evolve lighting control system
and can handle loads of up to 277v. The device can be easily mounted in a single or multi-gang
electrical box in any existing environment and is compatible with Z-Wave security systems.
Inclusion of this Module on a Z-Wave network allows remote ON/OFF control of the load
connected and it’s fully scene capable.
This Isolated Contact Fixture Module is designed to work with other Evolve enabled devices.
Evolve nodes of other types can be included in the network and will also act as repeaters to
increase the range of the network.
As part of a Z-Wave network, the LFM-20 will also act as a wireless repeater to ensure that
commands intended for another device in the network are received. This is useful when the
device would otherwise be out of the radio range of the wireless controller.
There are no field repairable assemblies on this unit. If service is needed, the unit must be
returned where purchased.
Specifications
•
•
•
•
•
•
SKU: LFM-20
Supported Networks:
- Z-Wave – Signal (Frequency) 908.42 MHz
Range: Up to 100 feet line of sight between the Wireless Controller and/or the closest Evolve
Receiver Module
Power: 120 VAC, 60 Hz
Dimensions: 3” H x 1.875” W x 1.5” D
Weight: 0.28 lbs.
CD-LFM20-01
PRODUCT OVERVIEW
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,FS20Z-1,GO CONTROL; P/N: 10008918 X3; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500” x 11.000”; TOLERANCE ± .125”; SCALE: 1-1; PAGE 1 OF 2
Wiring
The LFM-20 is wired as follows:
•
•
•
•
Black – represents the line input, 120VAC
White – represents the neutral. The LFM-20 and the load must share the same neutral.
Blue 1 (either blue wire) – 24V – 277V input for load switching
Blue 2 (either blue wire) – 24V – 277V output for load switching
FS20Z-1
The switch also has a green wire
which
serves
as the ground.
While there120
is a yellow
Z-Wave
Radio
Frequency
(RF) Controlled,
VAC wire
present, it is not needed and should be cut and capped with either electrical tape or a wire nut.
Scene Capable, Isolated Contact Fixture Module, Series 300
DRY CONTACT WIRING
LOAD IS POWERED FROM
AN ISOLATED SUPPLY
NEUTRAL
BLUE
LOAD POWER
SOURCE
24 TO 277 VOLTS
WHITE
120 VAC
LINE
FS20
Fixtur
e
Serie Module Re
s 300,
ceive
S/N
Re
r
WHITE
NEUTRAL
LOAD
20 AMPS
MAXIMUM
WHITE
120 VAC
BLACK
Z-1
l. 5.41
120 Vol
Isolate ts AC, 60 Hz
d
277VAC Output Con 908.42 MH
1/2 HP , 5540W (matact Rating z
s (UL
Motor,
x),
120VAC 20 Amp, /CUR)
, 960W Resistiv
Incand e 120/24
Do not
escent
0VA
Load C
FCC exceed ele
ID:
ctri
Canada QIE0791-0 cal ratings
.
1
Linear IC: 4436A079101
LLC,
Carlsba
BLK:
Lin
BLUE: e, WHITE d, CA
: Neu
Load,
GRN: tral,
Ground
WET CONTACT WIRING
LOAD IS POWERED FROM
THE SAME SUPPLY AS FS20Z-1
BLUE
LOAD
20 AMPS
MAXIMUM
LINE
BLACK
BLUE
BLUE
WAR
NIN
G:
STATUS LED
3B54
M
PUSH BUTTON TO
ADD NODE TO NETWORK
STATUS LED
PUSH BUTTON TO
ADD NODE TO NETWORK
P175
3
FS20Z-1
LFM-20
FS20Z-1
LFM-20
GREEN
GROUND
GREEN
GROUND
NOTE: This unit must be added to the Network only where it will be permanently installed. The proper operation of this node in the
mesh network is dependent on it knowing its location
respect
other nodes.
You cannot
“test bench”
configure
this are
unit, then
In thewith
case
of to
a 3-way
or 4-way
circuit,
traveler
wires
notinstall.
used when building an Evolve
network. Instead, an LFM-20 may be used in conjunction with an LTM-5 to create a wireless,
Protection
“virtual” 3-way. SeeOver-current
LTM-5 for further
details.
The FS20Z-1 is protected by an internal fuse. This internal fuse is factory
GoControl™ family of Z-Wave® certified wireless lighting products
Maximum
Load: serviceable only. Check the home circuit breakers before concluding that the
art LED fixtures, bulbs, switches, dimmers, outlets, plug-in
modules, and
returned. 277 VAC, 10FLA, 60LRA, 250VAC
Isolated
Contacts:
20product
ampsmust
G.P.bemaximum,
mostats) and security devices (alert sounder, motion sensor, and door/
Motor:
1 H.P. maximum,
120/240
VAC
Adding
to a network:
dow sensor) bring a new level of intelligent wireless capability
to commercial
See the Wireless Controller operating instructions for details to include this
residential environments.
Incandescent: TV8 module
(Tungsten),
120command
VAC, 960W
under the
of themaximum
Wireless Controller.
Z-Wave wireless protocol is an international wireless standard for remote
1. Prepare the Controller to include a unit to the network, by adding it to a group
e automation, security and other applications. This product can be included
(method of adding a node to the network). Refer to Controller instructions.
operated in any Z-Wave network with other Z-Wave certified devices
2.
The FS20Z-1 must be in its permanently installed location. Press the button
other manufacturers and/or other applications. All non-battery operated
on the FS20Z-1 once.
es within the network will act as repeaters regardless of vendor to increase
Wire this module in 3.
series
with a see
20 amp
(maximum)
according
to “DEVICE
one of the
Installation
You should
an indication
on yourload
Controller
that the
WASdiagrams
bility of the network.
above. The LFM-20 hasINCLUDED”
an isolated
relay
output on the two BLUE wires. BLACK is for the 120 VAC
in
the
network.
Control Z-Wave products are easy to install, are Z-Wave certifi
ed,WHITE
and allow
Line.
is for the
VAC
Neutral.
Withadding
dry contact
wiring,
load
is be
powered
✓ 120
NOTE:
If you
have trouble
the FS20Z-1
to athe
group
it may
that the by a separate
ers to create an integrated wireless network with nearly limitless
expansion
source. With wet contact
wiring,
the
load
is
powered
from
the
same
source
as
the
Home ID and Node ID were not cleared from it after testing. You must
firstLFM-20.
interoperability with security, energy management, home entertainment,
“RESET UNIT” with your controller to remove it from the network. Although
iances, and more.
Fixture Mounted Configuration
adding it to a group includes it in the network, removing it from a group does
NGER! SHOCK HAZARD. Read and understand
Push the these
button on thenot
face
to configure
module
to operate
from the
Wireless
remove
it from the the
network.
If removed
from a group,
it functions
onlyController.
uctions before installing. This device is intended forWith
installation
in
the Wireless
Controller,
the
LFM-20
can
be
switched
ON
and
OFF
remotely,
and can be
as a repeater.
ordance with the National Electric code and local regulations
in the United
included
in groups of lights that operate at the same time (a group can also be a single module),
from a network:
es, or the Canadian Electrical Code and local regulationsand
in Canada.
is setRemoving
scenesIt that
a lighting mood.
The FS20Z-1 can be removed from the network by the Controller/Gateway.
mmended that a qualified electrician perform this installation. Make sure
otal load controlled does not exceed 20 amps.
Other Functions Refer to the Controller operating instructions for details.
1. Set the
Controller
Removal
Mode and
follow its instruction
to delete
The button on the LFM-20
also
plays ainto
role
as a reset
in addition
to including
thethe
module in
ndoor use only. Retain instructions for future use.
groups and scenes. FS20Z-1 from the Controller.
TALLATION
2. Remove the module by tapping the button three times, then press and hold.
e this module in series with a 20 amp (maximum) load according
to one Protection
3. You should see an indication on your Controller that the “device was
Over-current
e diagrams above. The FS20Z-1 has an isolated relay output
on the two
removed”
the network.
The LFM-20
is protected
by an from
internal
fuse. The internal fuse is factory serviceable only. Check
E wires. BLACK is for the 120 VAC Line. WHITE is for the 120
Neutral.
theVAC
circuit
breakers
before
concluding
that
BASIC OPERATION the product must be returned.
dry contact wiring, the load is powered by a separate source. With wet
Button (Local Control)
act wiring, the load is powered from the same source as the FS20Z-1.
For testing, the button on the FS20Z-1 allows the installer to turn the load ON
ure Mounted Configuration
or OFF.
h the button on the face to configure the module to operate from the
• Tapping button toggles the load attached ON or OFF.
eless Controller. With the Wireless Controller, the FS20Z-1 can be switched
• Also used to include or exclude the module from the Z-Wave system.
and OFF remotely, and can be included in groups of lights that operate at
When a Controller prompts to “Send Node ID” or to “Press Button on Unit”,
same time (a group can also be a single module), and in scenes that set
quickly tap the button once to satisfy those instructions. (Tapping the button
hting mood.
also toggles the load attached ON or OFF.)
0Z-1 DUPLEX RECEPTACLE
CD-LRMAS-01
PRODUCT OVERVIEW
LRM-AS
Product
Description
Dimmer
The Evolve Wall Mounted Dimmer is a component of the Evolve lighting control system. It is fully
scene capable and can handle loads of up to 500W for control of permanently installed lighting
fixtures only (not for control of receptacles). The Evolve Wall Mounted Dimmer is easily wired
in place of a standard wall dimmer in any existing environment. Inclusion of this Dimmer on a
Z-Wave network allows remote ON/OFF control and dimming of loads connected. This device is
compatible with Z-Wave security systems and the Auto-Sense feature allows for local lamp
activation independent of the Z-Wave controller status.
This Wall Mounted Dimmer is designed to work with other Evolve enabled devices. Evolve nodes
of other types can be included in the network and will also act as repeaters to increase the range
of the network. The Dimmer also has a replaceable trim ring available in assorted colors.
As part of a Z-Wave network, the LRM-AS will also act as a wireless repeater to ensure that
commands intended for another device in the network are received. This is useful when the
device would otherwise be out of the radio range of the wireless controller.
Specifications
•
•
•
•
•
•
•
SKU: LRM-AS
Supported Networks:
- Z-Wave – Signal (Frequency) 908.42 MHz
Range: Up to 100 feet line of sight between the Wireless Controller and/or the closest Evolve
Receiver Module
Power: 120 VAC, 500W, 60 Hz
Dimensions: 4.5” H x 2.75” W x 1.75” D
Weight: 0.33 lbs.
Requires a Neutral
CD-LRMAS-01
Wiring
PRODUCT OVERVIEW
The LRM-AS is wired in the same fashion as a conventional digital switch – it requires a
minimum of 3 wires to operate:
•
•
•
Black – represents the line input, 120VAC
White – represents the neutral
Blue – represents the load (switch leg)
The switch also has a green wire which serves as the ground.
WD500Z-1
In the case of a 3-way or 4-way
circuit,Radio
traveler
wires are not
when building
Evolve
Z-Wave
Frequency
(RF)used
Controlled,
500W,an120
VAC
network. Instead, an LRM-AS may be used in conjunction with an LTM-5 to create a wireless,
Wall Mounted Dimmer, Series 300
“virtual” 3-way. See LTM-5 for further details.
NEUTRAL
120 VAC
LINE
WHITE
BLACK
BLUE
LOAD
PUSH ON/HOLD TO
BRIGHTEN
YELLOW (NOT USED)
CAP YELLOW WIRE
A.G. SWITCH
IN - OPERATION
OUT - CHANGE LOAD
SUPPLIED WITH DECORATIVE SWITCH PLATE
SCORED TAB
WILL BREAK FLUSH
WITH EDGE OF
PLASTIC
PUSH OFF/ HOLD TO DIM
GREEN
GROUND
STATUS LED
PUSH TOP OR
BOTTOM OF PADDLE
SWITCH TO CONFIGURE
NOTE: This
module must be “included inWith
the Network”
onlyoff,
where
it will
permanently
installed.
The diagram
proper operation
of this
node in the
the power
wire
thebe
LRM-AS
according
to the
shown.
Caution!
Do not wire unit
Installation
mesh network is dependent on it knowing
its location
with respect
to other
nodes.
“test bench”
configure
thistomodule.
“live”
(with power
on the
circuit)
andYou
docannot
not allow
the yellow
wire
contact line voltage, neutral
or ground or you will damage the device.
WD500Z-1 WALL MOUNTED
If more than one LRM-AS is to be installed in a wall box, scored tabs on the side can be broken
with pliers to accommodate proper fit. Apply power when
DIMMERoff by bending back and forth
INSTALLATION
completed.
Linear’s family of Z-Wave certified wireless lighting controls (switches,
dimmers, outlets and plug-in modules) brings a new level of intelligent
wireless capability to commercial and residential environments.
The Z-Wave wireless protocol is an international wireless standard
for remote home automation, security and other applications.
Embedded in each device, the Z-Wave smart chip enables two-way RF
communication among hundreds of Z-Wave enabled devices, allowing
products and services from multiple manufacturers to work seamlessly.
Linear Z-Wave products are easy to install, and allow dealers to create
an integrated wireless network with nearly limitless expansion and
interoperability with security and health monitoring systems, energy
management, home entertainment, appliances, and more.
DANGER! SHOCK HAZARD. Read and understand these
instructions before installing. This device is intended for installation in
accordance with the National Electric code and local regulations in the
United States, or the Canadian Electrical Code and local regulations
in Canada. It is recommended that a qualified electrician perform this
installation. Make sure the total load controlled does not exceed 1800
watts. For indoor use only. Retain instructions for future use.
CAUTION: To reduce the risk of overheating and possible
damage to other equipment, do not install to control a receptacle,
With power off, wire this WD500Z-1 according to the diagram show.
Caution! Do not wire unit “live” (with power on the circuit) and do not
allow the yellow wire to contact line voltage, neutral or ground or you
will damage the device.
If more than one WD500Z-1 is to be installed in a wall box, scored tabs
on the side can be broken off by bending back and forth with pliers, to
accommodate proper fit. Apply power when completed
Remote Control
The WD500Z-1 will respond to BASIC and MULTILEVEL commands
that are part of the Z-Wave system. Refer to your controller’s instructions
as to whether your controller can transmit those commands.
All On/All Off
The WD500Z-1 supports the ALL ON/ ALL OFF commands.
The WD500Z-1 can be set to respond to ALL ON and ALL OFF
commands 4 different ways. Refer to your controller for information on
how to set the WD500Z-1 to operate in the manner you desire. Some
controllers may be only able to set certain settings of ALL ON/ALL OFF
response. The 4 different ways the WD500Z-1 can be setup to respond
to ALL ON and ALL OFF commands are:
• WD500Z-1 will not respond to ALL ON or the ALL OFF command.
CD-LSM15-01
PRODUCT OVERVIEW
LSM-15
Product
Description
Binary Switch
The LSM-15 Wall Mounted Binary Switch is a component of the Evolve lighting control system.
Inclusion of this Switch on a Z-Wave network allows remote ON/OFF control of loads connected
and is compatible with Z-Wave security systems. It can be used on any type of 120 VAC fixture or
bulb type, with a 15A limit.
This Wall Mounted Binary Switch is designed to work with other Evolve enabled devices. Evolve
nodes of other types can be included in the network and will also act as repeaters to increase the
range of the network. The Switch also has a replaceable trim ring available in assorted colors.
As part of a Z-Wave network, the LSM-15 will also act as a wireless repeater to ensure that
commands intended for another device in the network are received. This is useful when the
device would otherwise be out of the radio range of the wireless controller.
Specifications
•
•
•
•
•
•
SKU: LSM-15
Supported Networks:
- Z-Wave – Signal (Frequency) 908.42 MHz
Range: Up to 130 feet line of sight
Power: 120 VAC
Dimensions: 4.5” H x 2.75” W x 1.75” D
Weight: 0.29 lbs.
CD-LSM15-01
Wiring
PRODUCT OVERVIEW
The LSM-15 is wired in the same fashion as a conventional digital switch – it requires a minimum
of 3 wires to operate:
• Black – represents
the line input, 120VAC
PRINTER’S INSTRUCTIONS:
•
White
–
represents
neutral
INSTR,INSTL,WS15Z-1, GO CONTROL; P/N: 10008577 X5; INK: BLACK; MATERIAL:the
20# MEAD
BOND; SIZE: 8.500” x 11.000”; TOLERANCE ± .125”; SCALE: 1-1; PAGE 1 OF 2
• Blue – represents the load (switch leg)
The switch also has a green wire which serves as the ground. While there is a yellow wire
present, it is not needed and should be cut and capped with either electrical tape or a wire nut.
WS15Z-1
In the case of a 3-way or 4-way circuit, traveler wires are not used when building an Evolve
network. Instead, an LSM-15 may be used in conjunction with an LTM-5 to create a wireless,
“virtual” 3-way. See LTM-5 for further details.
Z-Wave Radio Frequency (RF) Controlled, 120 VAC
Scene and NWI Capable, Wall Mounted Switch, Series 300
NEUTRAL
120 VAC
LINE
WHITE
BLUE
BLACK
SCORED TAB WILL
BREAK FLUSH WITH
EDGE OF PLASTIC
LOAD
15 AMPS
MAXIMUM
PUSH ON
LSM-15 AND THE LOAD
WS15Z-1
MUST SHARE THE SAME
PROPRIETARY NEUTRAL
PUSH OFF
Shown with supplied
decorative trim plate
TAP TOP OR BOTTOM
OF SWITCH PADDLE
TO CONFIGURE
GREEN GROUND
STATUS LED
NOTE: This unit must be added to the Network only where it will be permanently installed. The proper operation of this node in the
mesh network is dependent on it knowing its location with respect to other nodes. You cannot “test bench” configure this unit, then install.
WS15Z-1 WALL MOUNTED SWITCH
Removing from a network:
Wire this switch in place of a current
wall switch
to the
diagram
When used, the
The WS15Z-1
can beaccording
removed from
the network
byabove.
the Controller/Gateway.
The GoControl family of Z-Wave® certified
wireless are
lighting
products
LSM-15’s
required
to be wired
to
the
same
line
(or
neutral)
which
is
also
wired
to the load
Refer to the Controller operating instructions for details.
(smart LED fixtures, bulbs, switches, dimmers, being
outlets,controlled,
plug-in modules,
and and
not wired to any other neutral. If multiple neutrals are tied together in one
1. Set the Controller into Removal Mode and follow its instruction to delete the
thermostats) and security devices (alert sounder,
sensor,
door/ to preserve
box,motion
separate
theand
neutrals
the integrity of the LSM-15 circuit.
WS15Z-1 from the Controller.
window sensor) bring a new level of intelligent wireless capability to commercial
Remove
the switch
by circuit).
tapping the paddle 2 times.
and residential environments.
Caution! Do not wire unit “live”2.(with
power
on the
3.
You
should
see
an
indication
on your Controller that the “device was
The Z-Wave wireless protocol is an international wireless standard for remote
removed”
from
the
network.
home automation, security and other applications. This product can be included
and operated in any Z-Wave network with other Z-Wave certified devices
BASIC OPERATION
from other manufacturers and/or other applications. All non-battery operated
(Local Control)
nodes within the network will act as repeaters regardless of vendor to increase
The switch paddle on the WS15Z-1 allows the user to:
reliability of the network.
• Turn the attached load on or off.
GoControl Z-Wave products are easy to install, are Z-Wave certified, and allow
• Tapping top of switch turns the load attached ON.
dealers to create an integrated wireless network with nearly limitless expansion
• Tapping bottom of switch turns the load attached OFF.
and interoperability with security, energy management, home entertainment,
LED
Indication
appliances, and more.
To act as a night light, the LED on the WS15Z-1 will turn ON when the load
DANGER! SHOCK HAZARD. Read and understand these instructions before
attached is OFF. However, the LED can be user configured to turn ON, when
installing. This device is intended for installation in accordance with the National
the load attached is ON, if so desired. See “CONFIGURATION” section.
Electric code and local regulations in the United States, or the Canadian
Remote
Control
Electrical Code and local regulations in Canada. It is recommended that a
The
WS15Z-1
will respond to BASIC and BINARY commands that are part of
qualified electrician perform this installation. Make sure the load controlled by
the
Z-Wave
system.
Refer to your Controller’s instructions as to whether your
the switch does not exceed 1800 watts. For indoor use only. Retain instructions
Controller can transmit those commands.
for future use.
Installation
™
INSTALLATION
Wire this switch in place of a current wall switch according to the diagram
above. When used, WS15Z-1’s are required to be wired to the same line (or
neutral) which is also wired to the load being controlled, and not wired to any
other neutral. If multiple neutrals are tied together in one box, separate the
neutrals to preserve the integrity of the WS15Z-1 circuit.
✓ CAUTION! Do not wire unit “live” (with power on the circuit).
Adding to a network:
CD-LTM5-01
PRODUCT OVERVIEW
LTM-5
Product
Description
3-Way Accessory Switch
The Evolve 3-Way Wall Mounted Switch is a component of the Evolve lighting control system and
is wired in place of a standard wall switch in any existing environment. Inclusion of this Switch on
a Z-Wave network allows remote ON/OFF control and dimming of the loads connected, creating
virtual 3-way switches. It’s fully compatible with Z-Wave security systems and does not directly
control a load - rather it communicates with other load controlling devices or plug-in modules.
This 3-Way Wall Mounted Switch is designed to work with other Evolve enabled devices. Evolve
nodes of other types can be included in the network and will also act as repeaters to increase the
range of the network. The Switch also has a replaceable trim ring available in assorted colors.
As part of a Z-Wave network, the LTM-5 will also act as a wireless repeater to ensure that
commands intended for another device in the network are received. This is useful when the
device would otherwise be out of the radio range of the wireless controller.
Specifications
•
•
•
•
•
•
SKU: LTM-5
Supported Networks:
- Z-Wave – Signal (Frequency) 908.42 MHz
Range: Up to 130 feet line of sight
Power: 120 VAC, 60 Hz
Dimensions: 4.5” H x 2.75” W x 1.75” D
Weight: 0.31 lbs.
CD-LTM5-01
Wiring
PRODUCT OVERVIEW
The LTM-5 does not control a circuit directly; rather it communicates wirelessly to another
associated Evolve device, which in turn controls the required circuit. As there is no load control
from the LTM-5, it only requires 120VAC power and neutral to operate:
•
•
Black – represents the line input, 120VAC
White – represents the neutral
The switch also has a green wire which serves as the ground. While there is a yellow wire
present, it is not needed and should be cut and capped with either electrical tape or a wire nut.
For operation after the LTM-5 has been successfully programmed:
•
•
If configured to work in conjunction with an LSM-15: Tap top paddle for ON, tap bottom
paddle for OFF.
If configured to work in conjunction with an LRM-1000: Tap top paddle for ON, and the
LRM-1000 returns to its last set brightness, which does not necessarily mean full brightness;
tap bottom paddle for OFF (0% brightness), push and hold top/bottom to control dimming
level.
This device is frequently used when creating virtual 3-way or 4-way circuits. Below is an example
of proper wiring when converting an existing 3-way circuit, into an Evolve 3-way virtual circuit:
Switch with
existing load
Switch with existing power
On an existing 3-way switch, one switch has an existing load control (on left) and one switch has
existing line power (on right). There are two traveler wires between the switches.
In an Evolve circuit, only one device is required to control the load. The LTM-5 is then used to
create a “virtual” 3-way circuit, where the LTM-5 communicates wirelessly to the load controlling
switch to either turn on, turn off, or change the dim level of the circuit. In the pictured example
above, the left hand side switch has a 120VAC, neutral, and load wire – everything required for
either an LSM-15 or LRM-1000. The right hand side switch has 120VAC and 2 wires that travel to
the left side switch. To add an LTM-5 to the right hand side the electrician would need to tie one
of these 2 wires to neutral at the left side switch. If the application called for the load bearing
switch (LSM-15 or LRM-1000) to be located on the right hand side, then both a neutral and load
wire would be tied together at the left side switch.