FireStop™
CONDUIT AND EMT SYSTEMS
UL SYSTEM NO. C-AJ-1509
F Rating – 3 hr., T Rating – 0 hr.
3b
1
3a
2
3a
3b
1. &LOORORWALLASSEMBLY – Minimum 41/2 in. thick reinforced normal weight concrete. Wall may also be constructed of any UL
Classified concrete blocks. Maximum diameter of opening is 8 in. See Concrete Blocks (CAZT) category in the Fire Resistance Directory
for names of manufacturers.
2. Through Penetrant – One metallic pipe, conduit or tubing to be installed either concentrically or eccentrically within the firestop
system. Pipe, conduit or tubing to be rigidly supported on both sides of floor or wall assembly. A maximum of one pipe, conduit or tubing
to be installed within the opening. The space between the pipe, conduit or tubing and the periphery of opening shall be a minimum of
0 in. to a maximum of 2 in. The following types and sizes of metallic pipes, conduits or tubing may be used:
a) Steel pipe – Nom. 24 in. diameter (or smaller) Schedule 10 (or heavier) steel pipe
b) Conduit – Nom. 6 in. diameter (or smaller) electrical metallic tubing or steel conduit
c) Copper tubing – Nom. 6 in. diameter (or smaller) Type L (or heavier) copper tubing
d) Copper pipe – Nom. 6 in. diameter (or smaller) Regular (or heavier) copper pipe.
3. Firestop System – The firestop system shall consist of the following:
a) Packing material – NSi FireStop Mineral Wool. Minimum 4 in. thickness of minimum 4 pcf mineral wool batt insulation firmly packed
into opening as a permanent form. Packing material to be recessed from top surface of floor or from both surfaces of wall as required
to accommodate the required thickness of fill material
b) Fill, void or cavity material – NSi FireStop Intumescent Caulk. Minimum 1/4 in. thickness of fill material applied within the annulus,
flush with top surface of floor or with both surfaces of wall. At the point contact location between through penetrant and concrete, a
minimum 1/4 in. diameter bead of fill material shall be applied at the concrete/through penetrant interface on the top surface of floor
and on both surfaces of wall.
2
UL SYSTEM NO. C-AJ-1510
F Rating – 2 hr., T Rating – 0 hr.
4b 2
1
4a
3
1. &LOORORWALLASSEMBLY – Minimum 21/2 in. thick reinforced lightweight or normal weight (100-150 pcf) structural concrete. Floor
may also be constructed of any minimum 6 in. thick UL Classified hollow-core precast concrete units. Wall may also be constructed of
any UL Classified concrete blocks. Maximum diameter of opening is 261/4 in. Maximum diameter of opening in floors constructed of
hollow-core is 7 in. See Concrete Blocks (CAZT) or Precast Concrete Units (CFTV) category in the Fire Resistance Directory for names of
manufacturers.
2. Steel Sleeve (optional) – Nom. 26 in. diameter (or smaller) Schedule 10 (or heavier) steel pipe cast or grouted into floor or wall
assembly, flush with floor or wall surfaces.
4a
4b
3
3. Through Penetrant – One metallic pipe, conduit or tubing, rigidly supported on both sides of floor or wall assembly. The annular space
between the pipe or conduit and the periphery of opening shall be a minimum of 0 in. (point contact) to a maximum of 21/4 in. The
following types and sizes of metallic pipes, conduits or tubing may be used:
a) Copper tubing – Nom. 6 in. diameter (or smaller) Type L (or heavier) copper tube
b) Steel pipe – Nom. 24 in. diameter (or smaller) Schedule 10 (or heavier) steel pipe
c) Conduit – Nom. 6 in. diameter (or smaller) steel electrical metallic tubing (EMT)
d) Iron pipe – Nom. 24 in. diameter (or smaller) cast or ductile iron pipe.
4. Firestop System – The firestop system shall consist of the following:
a) Packing material – NSi FireStop Mineral Wool. Minimum 4.5 pcf mineral wool batt insulation, tightly compressed and firmly packed
into opening as a permanent form to a minimum depth of 21/4 in. Packing material to be recessed from top surface of floor or from
both surfaces of wall as required to accommodate the required thickness of sealant
b) Fill, void or cavity material – NSi FireStop Intumescent Caulk. Minimum 1/4 in. thickness of caulk applied within the annulus, flush
with top surface of floor or with both surfaces of wall. In floors constructed of hollow-core precast concrete units, fill material installed
symmetrically on both sides of floor. Additional material installed to form a minimum 1/4 in. crown bead at the point contact location
between the pipe and periphery of the opening. For vertical installations, sealant to be applied symmetrically on both sides of wall.
211 NSi
FireStop™
CONDUIT AND EMT SYSTEMS
UL SYSTEM NO. C-AJ-1511
F Rating – 2 hr., T Rating – 0 hr.
3
1
1. &LOORORWALLASSEMBLY – Minimum 21/2 in. thick reinforced lightweight or normal weight (100-150 pcf) concrete floor. Floor may
also be constructed of any minimum 6 in. thick UL Classified hollow-core precast concrete units. Wall may also be constructed of any UL
Classified concrete blocks. Maximum diameter of opening is 24 7/8 in. Maximum diameter of opening in floors constructed of hollow-core is
7 in. See Concrete Blocks (CAZT) or Precast Concrete Units (CFTV) category in the Fire Resistance Directory for names of manufacturers.
2. Through Penetrant – One metallic pipe, conduit or tubing to be installed within the firestop system. Pipe, conduit or tubing to be
rigidly supported on both sides of floor or wall assembly. The annular space between the pipe or conduit and the periphery of opening shall
be a minimum of 0 in. (point contact) to a maximum of 7/8 in. The following types and sizes of metallic pipes, conduits or tubing may be
used:
a) Steel pipe – Nom. 24 in. diameter (or smaller) Schedule 10 (or heavier) steel pipe
b) Iron pipe – Nom. 24 in. diameter (or smaller) cast or ductile iron pipe
c) Conduit – Nom. 6 in. diameter (or smaller) steel electrical metallic tubing or steel conduit
d) Copper pipe or tubing – Nom. 6 in. diameter (or smaller) Type L (or heavier) copper tubing.
2
3
3. Fill, void or cavity material – NSi FireStop Intumescent Caulk. Minimum 1/2 in. thickness of caulk applied within the annulus, flush
with top surface of floor or with both surfaces of wall. In floors constructed of hollow-core precast concrete units, fill material installed
symmetrically on both sides of floor. Additional material installed to form a minimum 1/4 in. crown bead at the point contact location
between the pipe and periphery of the opening. For vertical installations, sealant to be applied symmetrically on both sides of wall.
2
UL SYSTEM NO. W-L-1349
F Rating – 2 hr., T Rating – 0 hr.
1a
3
2
1b
3
2
1. 7ALL!SSEMBLY – The fire-rated gypsum wallboard/stud wall assembly shall be constructed of the materials and in the manner
described in the individual U300 or U400 Series Wall or Partition Design in the UL Fire Resistance Directory and shall include the following
construction features:
a) Studs – Wall framing may consist of either wood studs or steel channel studs. Wood studs to consist of nom. 2 x 4 in. lumber spaced
16 in. oc. Steel studs to be minimum 3 5/8 in. wide and spaced maximum 24 in. oc. When steel studs are used and the diameter
of openings exceeds the width of stud cavity, the opening shall be framed on all sides using lengths of steel stud installed between
vertical studs and screw-attached to the studs at each end. The framed opening in the wall shall be 4 to 6 in. wider and 4 to 6
in. higher than the diameter of the penetrating item such that, when the penetrating item is installed in the opening, a 2 to 3 in.
clearance is present between the penetrating item and the framing on all four sides.
b) Wallboard, Gypsum – 5/8 in. thick, 4 ft. wide with square or tapered edges. The gypsum wall board type, thickness, number of layers,
fastener type and sheet orientation shall be as specified in the individual U300 or U400 Series Design in the UL Fire Resistance
Directory. Maximum diameter of opening is 6 5/8 in.
2. Through Penetrant – One metallic pipe, conduit or tubing to be installed either concentrically or eccentrically within the firestop
system. The annular space between pipes, conduits or tubing and the periphery of opening shall be a minimum of 0 in. (point contact)
to a maximum of 1/2 in. Pipe, tubing or conduit to be rigidly supported on both sides of wall assembly. The following types and sizes of
metallic pipes, tubing or conduits may be used:
a) Steel pipe – Nom. 24 in. diameter (or smaller) Schedule 5 (or heavier) steel pipe
b) Iron pipe – Nom. 24 in. diameter (or smaller) cast or ductile iron pipe
c) Conduit – Nom. 6 in. diameter (or smaller) steel electrical metallic tubing or steel conduit
d) Copper Tubing – Nom. 6 in. diameter (or smaller) Type L (or heavier) copper tubing
e) Copper Pipe – Nom. 6 in. diameter (or smaller) Regular (or heavier) copper pipe.
3. Fill, void or cavity material – Sealant – NSi FireStop Intumescent Caulk. Minimum 11/4 in. thickness of fill material applied within
the annulus, flush with both surfaces of wall. At the point contact location between through penetrant and gypsum wall board, a minimum
1
/2 in. diameter bead of fill material shall be applied at the gypsum wallboard/through penetrant interface on both surfaces of wall.
2010 CATALOG
NSi 212
FireStop™
CONDUIT AND EMT SYSTEMS
UL SYSTEM NO. W-L-1350
1a
F Rating – 2 hr., T Rating – 0 hr.
3
4
2
1b
4
1. 7ALL!SSEMBLY – The fire-rated gypsum wallboard/stud wall assembly shall be constructed of the materials and in the manner
described in the individual U300 or U400 Series Wall or Partition Design in the UL Fire Resistance Directory and shall include the
following construction features:
a) Studs – Wall framing may consist of either wood studs or steel channel studs. Wood studs to consist of nom. 2 x 4 in. lumber
spaced 16 in. oc. Steel studs to be minimum 3 5/8 in. wide and spaced maximum 24 in. oc. When steel studs are used and the
diameter of openings exceeds the width of stud cavity, the opening shall be framed on all sides using lengths of steel stud installed
between vertical studs and screw-attached to the studs at each end. The framed opening in the wall shall be 4 to 6 in. wider and 4
to 6 in. higher than the diameter of the penetrating item such that, when the penetrating item is installed in the opening, a 2 to 3
in. clearance is present between the penetrating item and the framing on all four sides
b) Wallboard, Gypsum – 5/8 in. thick, 4 ft. wide with square or tapered edges. The gypsum wall board type, thickness, number
of layers, fastener type and sheet orientation shall be as specified in the individual U300 or U400 Series Design in the UL Fire
Resistance Directory. Maximum diameter of opening is 7 5/8 in.
2. Through Penetrant – One metallic pipe, conduit or tubing to be installed either concentrically or eccentrically within the firestop
system. The annular space between pipes, conduits or tubing and the periphery of opening shall be a minimum of 0 in. (point contact)
to a maximum of 11/2 in. Pipe, tubing or conduit to be rigidly supported on both sides of wall assembly. The following types and sizes of
metallic pipes, tubing or conduits may be used:
a) Steel pipe – Nom. 24 in. diameter (or smaller) Schedule 5 (or heavier) steel pipe
b) Iron pipe – Nom. 24 in. diameter (or smaller) cast or ductile iron pipe
c) Conduit – Nom. 6 in. diameter (or smaller) steel electrical metallic tubing or steel conduit
d) Copper Tubing – Nom. 6 in. diameter (or smaller) Type L (or heavier) copper tubing
e) Copper Pipe – Nom. 6 in. diameter (or smaller) Regular (or heavier) copper pipe.
2
3. Packing Material – NSi FireStop Mineral Wool. Minimum 2 in. thickness of minimum 4 pcf mineral wool batt insulation firmly
packed into opening as a permanent form. Packing material to be recessed from both surfaces of the wall by 5/8 in.
4. Fill, void or cavity material – Sealant – NSi FireStop Intumescent Caulk. Minimum 5/8 in. thickness of fill material applied within
the annulus, flush with both surfaces of wall. Additional material to be installed such that a 1/4 in. crown bead is formed around the
penetrating item.
UL SYSTEM NO. W-L-1351
F Rating – 1 hr., T Rating – 0 hr.
1a
3
2
1b
3
2
1. 7ALL!SSEMBLY – The 1 hr. fire-rated gypsum wallboard/stud wall assembly shall be constructed of the materials and in the manner
described in the individual U300 or U400 Series Wall or Partition Design in the UL Fire Resistance Directory and shall include the following
construction features:
a) Studs – Wall framing may consist of either wood studs or steel channel studs. Wood studs to consist of nom. 2 x 4 in. lumber spaced
16 in. oc. Steel studs to be minimum 3 5/8 in. wide and spaced maximum 24 in. oc. When steel studs are used and the diameter
of openings exceeds the width of stud cavity, the opening shall be framed on all sides using lengths of steel stud installed between
vertical studs and screw-attached to the studs at each end. The framed opening in the wall shall be 4 to 6 in. wider and 4 to 6
in. higher than the diameter of the penetrating item such that, when the penetrating item is installed in the opening, a 2 to 3 in.
clearance is present between the penetrating item and the framing on all four sides
b) Wallboard, Gypsum – 5/8 in. thick, 4 ft. wide with square or tapered edges. The gypsum wall board type, thickness, number of layers,
fastener type and sheet orientation shall be as specified in the individual U300 or U400 Series Design in the UL Fire Resistance
Directory. Maximum diameter of opening is 24 3/4 in. for steel stud walls. Maximum diameter opening is 141/2 in. for wood stud
walls.
2. Through Penetrant – One metallic pipe, conduit or tubing to be installed either concentrically or eccentrically within the firestop
system. The annular space between pipes, conduits or tubing and the periphery of opening shall be a minimum of 1/4 in. to a maximum
of 1/2 in. Pipe, tubing or conduit to be rigidly supported on both sides of wall assembly. The following types and sizes of metallic pipes,
tubing or conduits may be used:
a) Steel pipe – Nom. 24 in. diameter (or smaller) Schedule 5 (or heavier) steel pipe
b) Iron pipe – Nom. 24 in. diameter (or smaller) cast or ductile iron pipe
c) Conduit – Nom. 6 in. diameter (or smaller) steel electrical metallic tubing or steel conduit
d) Copper Tubing – Nom. 6 in. diameter (or smaller) Type L (or heavier) copper tubing
e) Copper Pipe – Nom. 6 in. diameter (or smaller) Regular (or heavier) copper pipe.
3. Fill, void or cavity material – Sealant – NSi FireStop Intumescent Caulk. Minimum 5/8 in. thickness of fill material applied within the
annulus, flush with both surfaces of wall.
213 NSi
FireStop™
CONDUIT AND EMT SYSTEMS
UL SYSTEM NO. W-L-1348
F Rating – 2 hr., T Rating – 0 hr.
1a
1. 7ALL!SSEMBLY – The 2 hr. fire-rated gypsum wallboard/stud wall assembly shall be constructed of the materials and in the manner
described in the individual U300 or U400 Series Wall or Partition Design in the UL Fire Resistance Directory and shall include the following
construction features:
a) Studs – Wall framing may consist of either wood studs or steel channel studs. Wood studs to consist of nom. 2 x 4 in. lumber spaced
16 in. oc. with nom. 2 x 4 in. lumber end plates and cross braces. Steel studs to be minimum 3 5/8 in. wide and spaced maximum
24 in. oc. When steel studs are used and the diameter of openings exceeds the width of stud cavity, the opening shall be framed on
all sides using lengths of steel stud installed between vertical studs and screw-attached to the studs at each end. The framed opening in
the wall shall be 4 to 6 in. wider and 4 to 6 in. higher than the diameter of the penetrating item, such that when the penetrating item
is installed in the opening, a 2 to 3 in. clearance is present between the penetrating item and the framing on all four sides
b) Wallboard, Gypsum – 5/8 in. thick, 4 ft. wide with square or tapered edges. The gypsum wall board type, thickness, number of
layers, fastener type and sheet orientation shall be as specified in the individual U300 or U400 Series Design in the UL Fire Resistance
Directory. Maximum diameter of opening is 5 in.
3
3
1b
2
3
2. Through Penetrant – One metallic pipe, conduit or tubing to be installed either concentrically or eccentrically within the firestop
system. The annular space between pipes, conduits or tubing and the periphery of opening shall be a minimum of 0 in. (point contact)
to a maximum of 13/4 in. Pipe, tubing or conduit to be rigidly supported on both sides of wall assembly. The following types and sizes of
metallic pipes, tubing or conduits may be used:
a) Steel pipe – Nom. 3 in. diameter (or smaller) Schedule 5 (or heavier) steel pipe
b) Conduit – Nom. 3 in. diameter (or smaller) steel electrical metallic tubing or galv. steel conduit
c) Copper Tubing – Nom. 3 in. diameter (or smaller) Type L (or heavier) copper tubing
d) Copper Pipe – Nom. 3 in. diameter (or smaller) Regular (or heavier) copper pipe.
2
3. Fill, void or cavity material – Sealant – NSi FireStop Intumescent Caulk. Minimum 11/4 in. thickness of fill material applied within
the annulus, flush with both surfaces of wall. At the point contact location between through penetrant and gypsum wall board, a minimum
3
/8 in. diameter bead of fill material shall be applied at the gypsum wallboard/through penetrant interface on both surfaces of wall.
UL SYSTEM NO. F-C-1128
F Rating – 1 hr., T Rating – 0 hr.
1a
3
1b
1c
3
2
3
2
1. &LOOR#EILING!SSEMBLY – The 1 hr. fire-rated solid or trussed lumber joist floor-ceiling assembly shall be constructed of the materials
and in the manner specified in the individual L500 Series Floor-Ceiling Designs in the UL Fire Resistance Directory and shall include the
following construction features:
a) Flooring System – Lumber or plywood subfloor with finish floor of lumber, plywood or Floor-Topping Mixture as specified in the
individual floor-ceiling design. Maximum diameter of floor opening is 5 in.
b) Wood Joists – Nom. 10 in. deep (or deeper) lumber, steel or combination lumber and steel joists, trusses or Structural Wood Members
with bridging as required and with ends firestopped
c) Wallboard, Gypsum – Nom. 4 ft. wide x 5/8 in. thick as specified in the individual floor-ceiling design. Wallboard nailed to wood joists.
2. Through Penetrant – One metallic pipe, conduit or tubing to be installed either concentrically or eccentrically within the firestop
system. The annular space between pipe, conduit or tubing and the periphery of opening shall be a minimum of 0 in. (point contact) to a
maximum of 1/2 in. Pipe, tubing or conduit to be rigidly supported on both sides of wall assembly. The following types and sizes of metallic
pipes, tubing or conduits may be used:
a) Steel pipe – Nom. 4 in. diameter (or smaller) Schedule 10 (or heavier) steel pipe
b) Iron pipe – Nom. 4 in. diameter (or smaller) cast or ductile iron pipe
c) Conduit – Nom. 4 in. diameter (or smaller) steel electrical metallic tubing or steel conduit
d) Copper Tubing – Nom. 4 in. diameter (or smaller) Type L (or heavier) copper tubing
e) Copper Pipe – Nom. 4 in. diameter (or smaller) Regular (or heavier) copper pipe.
3. Fill, void or cavity material – NSi FireStop Intumescent Caulk. Minimum 3/4 in. thickness of fill material applied within the annulus
on top surface of floor. Minimum 5/8 in. thickness of fill material applied within annulus on bottom surface of ceiling. Additional fill material to
be installed such that a minimum 1/2 in. thick crown is formed around the through penetrant on top surface of floor-ceiling assembly.
2010 CATALOG
NSi 214