Switch Firmware Version 8.0.14.13 Release Notes

Switch Firmware Version 8.0.14.13
50948-30 Rev A
QLogic Corporation
All rights reserved
Table of Contents
1
2
3
4
5
6
7
8
9
1
Switch Models
Version and Date
Changes
Bug Fixes
Known Issues
Additional Information
Trademarks
Notices
Contacting Support
Switch Models
This document applies to the following switches:



2
QLogic 5800 Switch
QLogic 5802 Switch
QLogic 3810 Switch
Version and Date
These release notes describe the changes, fixes, known issues, and release details that
apply to QLogic 3810 and QLogic 5800V Series Switch firmware, version 8.0.14.13 that was
released in December, 2014.
If you intend to use Enterprise Fabric Suite to manage QLogic 5800V Series switches with
firmware version 8.0.14.xx, you must use Enterprise Fabric Suite version 8.00.12.07 or
later.
The QLogic 3810 switch can be managed with the CLI or with the QuickTools graphical user
interface. QLogic does not support the use of Enterprise Fabric Suite to manage the QLogic
3810 switch.
3
Changes
There were no changes. See Section 4 for bug fixes.
Switch Firmware Version 8.0.14.13
Page 1 of 4
4
Bug Fixes
The following fixes have been made to the firmware between versions 8.0.14.08 and
8.0.14.13 and between QuickTools versions 8.00.14.03 and 8.00.14.08:
PR Number
Problem
116414
QuickTools issues a security warning when accessing unsigned resources.
122931
EFS and Performance View applications do not open on the Windows 7 Pro 32bit
system from c:\Program Files\QLogic_Corporation\Enterprise_Fabric_Suite directory
(default installation folder).
123310
images account password can be changed, causing firmware updates and dump
supports to fail.
123456
A QuickTools session is vulnerable to a cross-site scripting attack.
125121
Update QuickTools launch for help
125634
Browser fails to open for QuickTools online help on some systems.
125816
TR mapping using QuickTools between a 5800V switch and Brocade 5100 hangs in
the TR mapping manager.
125826
Implicit hard zoning is disabled and none of the zone objects in the active zone sets
are HardACL.
126029
Java 7u51 or later is required for 8.00.14.
126391
Java exceptions are encountered when creating TR mappings with a Brocade DCX.
126411
Util application crashes while configuring RADIUS.
126454
OpenSSL ChangeCipherSpec Man-in-the-Middle (MiTM) vulnerability.
126488
Ps command does not show running cim_server.
126496
Update firmware with new detection and launch code to support modern browsers.
126499
CIMServer backtrace errors arise after 15 hours of operation.
126519
QuickTools application hangs.
126523
When using QuickTools to archive a switch, the file extension (xml) is not applied on
the first attempt.
126539
CVE-2014-6271: Remote code execution vulnerability on Linux systems through the
GNU Bourne-again shell (BASH).
126579
CVE-2014-3566: Padding oracle on downgrading legacy encryption (POODLE)
vulnerability in OpenSSL
126598
Update supported SSL certificate types.
126636
Update SSL certificate to 2,048 bits.
126657
Fix intermittent Null pointer exception in Quick tools.
Switch Firmware Version 8.0.14.13
Page 2 of 4
5
Known Issues
The following table identifies the known issues in firmware version 8.0.14.13 and the
QuickTools 8.00.14.08 web applet.
PR Number
Problem
Firmware
15409
You may see sluggish response from the CLI when the switch is in a large fabric (12
or more switches and/or more than 350 devices), and the fabric is being discovered.
For example, fabric discovery would occur when adding a new switch to the fabric.
Discovering the fabric can take from one to five minutes depending on zoning size
and the number of switches.
16756
When upgrading firmware while in maintenance mode, the message WARNING: This
key is not certified with a trusted signature ... appears. This message is
incorrect and should be ignored.
17650
When running internal port loopbacks on a QLogic 5800V/5802V switch, intermittent
failures may be seen when inter-switch links are present. The workaround is to put
the switch in diagnostic mode, or to remove the inter-switch links.
The switch may have difficulty communicating with the DHCPv6 server with certain
options enabled. The following lines in the server.conf file on the DHCPv6 server
host should be commented out:
24439
109351
#
#
#
#
#
#
#
#
#
provide VoIP parameter (SIP protocol servers and domain names)
option sip-server 2000::300,2000::302,2000::303,2000::304
option sip-domain sip1.example.com,sip2.example.com
provide NIS information (server addresses and domain name)
option nis-server 2000::400,2000::401,2000::404,2000::405,2000::405
option nis-domain nis.example.com
provide NIS+ information (server addresses and domain name)
option nis+-server 2000::501,2000::502
option nis+-domain nisplus.example.com
If QLogic 5800VSeries Switches are configured in a stack with cascading 10G ISLs
(only one ISL between each switch), an Emulex 8G adapter (LP 1200x) running
traffic can experience a timeout when a stack NDCLA or hot reset is performed
using Enterprise Fabric Suite. If the 10G ISL configuration follows QLogic best
practices, the timeout does not occur. For information about best practices and
stacking, see the Stacking section of QLogic 5800V Series Stackable Fibre Channel
Switch Installation Guide, firmware version 8.0).
QuickTools
10750
While running QuickTools, if the IP address of the entry switch is changed, online
help not will open. To access the online help, close the current QuickTools session,
and then reopen QuickTools using the new IP address.
15438
You may see sluggish response from QuickTools when the switch is in a large fabric
(12 or more switches and/or more than 350 devices), and the fabric is being
discovered. For example, fabric discovery would occur when adding a new switch to
the fabric. Discovering the fabric can take from one to five minutes depending on
zoning size and the number of switches.
16999
When a new fabric is added, the Fabric Status bar may incorrectly show a warning
condition related to Nicknames differ. This warning goes away when the fabric is
fully discovered, and nickname conflicts between switches are resolved.
18183
To open the online help in QuickTools on a Mac OS platform, the default browser
must be set to a browser other than the one used to open QuickTools.
Switch Firmware Version 8.0.14.13
Page 3 of 4
PR Number
20291
6
Problem
When using the Firefox 2.0 browser with Solaris10, and opening and closing help
windows from the dialog boxes, the following message may be displayed: Firefox
is already running but is not responding. To open a new window, you
must first close the existing Firefox process or restart your system. If
this occurs, follow the instructions to continue opening help windows.
Additional Information
Read the following document files for more information:

7
readme_firmware_8.0.14.13.pdf
Trademarks
Accelera, Accelerating Cluster Performance, FastFabric, InfiniCon Systems, InfiniNIC,
InfiniPath, InfiniView, Intelligent NIC, Networking University, NetXen, QLogic, the QLogic
logo, ReadyPath, SANdoctor, SANsurfer, and SilverStorm are registered trademarks of
QLogic Corporation.
To the extent a name or logo does not appear on this list does not constitute a waiver of
any and all intellectual property rights that QLogic Corporation or its subsidiaries has
established in any of its product, feature, or service names or logos. All other brand and
product names are trademarks or registered trademarks of their respective owners.
8
Notices
Information furnished in this document is believed to be accurate and reliable. However,
QLogic Corporation assumes no responsibility for its use, nor for any infringements of
patents or other rights of third parties which may result from its use. QLogic Corporation
reserves the right to change product specifications at any time without notice. Applications
described in this document for any of these products are only for illustrative purposes.
QLogic Corporation makes no representation nor warranty that such applications are
suitable for the specified use without further testing or modification. QLogic Corporation
assumes no responsibility for any errors that may appear in this document.
9
Contacting Support
Please feel free to contact your QLogic approved reseller or QLogic Technical Support at any
phase of integration for assistance. QLogic Technical Support can be reached by the
following methods:
Web: http://support.qlogic.com
E-mail: support@qlogic.com
Go to Top
© Copyright 2014. All rights reserved worldwide. QLogic, the QLogic logo, and the Powered by
QLogic logo are registered trademarks of QLogic Corporation. All other brand and product
names are trademarks or registered trademarks of their respective owners.
Switch Firmware Version 8.0.14.13
Page 4 of 4