BGT24MR2
Silicon Germanium 24 GHz Twin IQ Receiver MMIC
Data Sheet
Revision 3.1, 2014-03-25
RF & Protection Devices
Edition 2014-03-25
Published by
Infineon Technologies AG
81726 Munich, Germany
© 2014 Infineon Technologies AG
All Rights Reserved.
Legal Disclaimer
The information given in this document shall in no event be regarded as a guarantee of conditions or
characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any
information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties
and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights
of any third party.
Information
For further information on technology, delivery terms and conditions and prices, please contact the nearest
Infineon Technologies Office (www.infineon.com).
Warnings
Due to technical requirements, components may contain dangerous substances. For information on the types in
question, please contact the nearest Infineon Technologies Office.
Infineon Technologies components may be used in life-support devices or systems only with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.
BGT24MR2
Silicon Germanium 24 GHz Twin IQ Receiver MMIC
BGT24MR2 Silicon Germanium 24 GHz Twin IQ Receiver MMIC
Revision History: 2014-03-25, Revision 3.1
Previous Revision: 2013-07-08, Revision 3.1
Page
Subjects (major changes since last revision)
7
update feature list
Trademarks of Infineon Technologies AG
AURIX™, BlueMoon™, C166™, CanPAK™, CIPOS™, CIPURSE™, COMNEON™, EconoPACK™, CoolMOS™,
CoolSET™, CORECONTROL™, CROSSAVE™, DAVE™, EasyPIM™, EconoBRIDGE™, EconoDUAL™,
EconoPIM™, EiceDRIVER™, eupec™, FCOS™, HITFET™, HybridPACK™, I²RF™, ISOFACE™, IsoPACK™,
MIPAQ™, ModSTACK™, my-d™, NovalithIC™, OmniTune™, OptiMOS™, ORIGA™, PRIMARION™,
PrimePACK™, PrimeSTACK™, PRO-SIL™, PROFET™, RASIC™, ReverSave™, SatRIC™, SIEGET™,
SINDRION™, SIPMOS™, SMARTi™, SmartLEWIS™, SOLID FLASH™, TEMPFET™, thinQ!™,
TRENCHSTOP™, TriCore™, X-GOLD™, X-PMU™, XMM™, XPOSYS™.
Other Trademarks
Advance Design System™ (ADS) of Agilent Technologies, AMBA™, ARM™, MULTI-ICE™, KEIL™,
PRIMECELL™, REALVIEW™, THUMB™, µVision™ of ARM Limited, UK. AUTOSAR™ is licensed by AUTOSAR
development partnership. Bluetooth™ of Bluetooth SIG Inc. CAT-iq™ of DECT Forum. COLOSSUS™,
FirstGPS™ of Trimble Navigation Ltd. EMV™ of EMVCo, LLC (Visa Holdings Inc.). EPCOS™ of Epcos AG.
FLEXGO™ of Microsoft Corporation. FlexRay™ is licensed by FlexRay Consortium. HYPERTERMINAL™ of
Hilgraeve Incorporated. IEC™ of Commission Electrotechnique Internationale. IrDA™ of Infrared Data
Association Corporation. ISO™ of INTERNATIONAL ORGANIZATION FOR STANDARDIZATION. MATLAB™ of
MathWorks, Inc. MAXIM™ of Maxim Integrated Products, Inc. MICROTEC™, NUCLEUS™ of Mentor Graphics
Corporation. Mifare™ of NXP. MIPI™ of MIPI Alliance, Inc. MIPS™ of MIPS Technologies, Inc., USA. muRata™
of MURATA MANUFACTURING CO., MICROWAVE OFFICE™ (MWO) of Applied Wave Research Inc.,
OmniVision™ of OmniVision Technologies, Inc. Openwave™ Openwave Systems Inc. RED HAT™ Red Hat, Inc.
RFMD™ RF Micro Devices, Inc. SIRIUS™ of Sirius Satellite Radio Inc. SOLARIS™ of Sun Microsystems, Inc.
SPANSION™ of Spansion LLC Ltd. Symbian™ of Symbian Software Limited. TAIYO YUDEN™ of Taiyo Yuden
Co. TEAKLITE™ of CEVA, Inc. TEKTRONIX™ of Tektronix Inc. TOKO™ of TOKO KABUSHIKI KAISHA TA.
UNIX™ of X/Open Company Limited. VERILOG™, PALLADIUM™ of Cadence Design Systems, Inc. VLYNQ™
of Texas Instruments Incorporated. VXWORKS™, WIND RIVER™ of WIND RIVER SYSTEMS, INC. ZETEX™ of
Diodes Zetex Limited.
Last Trademarks Update 2010-10-26
Data Sheet
3
Revision 3.1, 2014-03-25
BGT24MR2
Silicon Germanium 24 GHz Twin IQ Receiver MMIC
Table of Contents
Table of Contents
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2
2.1
2.2
2.3
2.4
2.4.1
2.4.2
2.5
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Thermal Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
ESD Integrity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Measured RF Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
RX Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Temperature Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3
3.1
3.2
3.3
3.4
3.5
Application Circuit and Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Application Circuit Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Application Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Equivalent Circuit Diagram of MMIC Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
13
15
16
18
20
4
4.1
4.2
4.3
Physical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Package Footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Package Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
21
22
23
Data Sheet
4
Revision 3.1, 2014-03-25
BGT24MR2
Silicon Germanium 24 GHz Twin IQ Receiver MMIC
List of Figures
List of Figures
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Data Sheet
BGT24MR2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Application Circuit with Chip Outline (Top View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Timing Diagram of the SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Cross-Section View of Application Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Detail of Compensation Structure (valid for appl. board mat. Ro4350B, 0.254mm acc. to Fig. 4) . 18
Application Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Equivalent Circuit Diagram of MMIC Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Recommended Footprint and Stencil Layout for the VQFN32-9 Package . . . . . . . . . . . . . . . . . . . 21
Reflow Profile for BGT24MR2 (VQFN32-9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Package Outline (Top, Side and Bottom View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Marking Layout VQFN32-9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Tape of VQFN32-9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5
Revision 3.1, 2014-03-25
BGT24MR2
Silicon Germanium 24 GHz Twin IQ Receiver MMIC
List of Tables
List of Tables
Table 1
Table 2
Table 3
Table 4
Table 5
Table 6
Table 7
Table 8
Table 9
Table 10
Data Sheet
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Thermal Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
ESD Integrity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Typical Characteristics TA = -40 .. 105 °C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Typical Characteristics TA = -40 .. 105 °C, f = 24.0 .. 24.25 GHz . . . . . . . . . . . . . . . . . . . . . . . . . 11
Typical Characteristics Temperature Sensor TA = -40 .. 105 °C . . . . . . . . . . . . . . . . . . . . . . . . . 12
Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Pin Definition and Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
SPI Data Bit Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
SPI Timing and Logic Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6
Revision 3.1, 2014-03-25
Silicon Germanium 24 GHz Twin IQ
Receiver MMIC
1
•
•
•
•
•
•
•
•
•
•
•
•
•
BGT24MR2
Features
Gilbert based dual homodyne quadrature receiver
Single ended RF terminals
Low noise figure: NFSSB: 12 dB
High conversion gain: 26 dB
High 1 dB input compression point: -12 dBm
Low LO input power
Single supply voltage of 3.3 V
Integrated temperature sensor for monitoring purposes
Power consumption 300 mW in continuous operating mode
200 GHz bipolar SiGe:C technology b7hf200
Fully ESD protected device
VQFN-32-9 leadless plastic package incl. LTI-feature
Pb-free (RoHS compliant) package
Description
The BGT24MR2 is a Silicon Germanium MMIC (dual channel receiver) accommodating two separate homodyne
quadrature downconversion chains, operating from 24.0 to 24.25 GHz. It complements Infineons Transceiver
MMICs BGT24MTR11 and BGT24MTR12. LO buffer amplifiers are included to relax LO drive requirements and
individual LNAs provide low noise figures. RC polyphase filters (PPF) are used for LO quadrature phase
generation. The circuit is manufactured in a 0.18µm SiGe:C technology offering a cutoff frequency of 200 GHz.
The MMIC is packaged in a 32 pin leadless RoHs compliant VQFN package.
Product Name
Package
Chip
Marking
BGT24MR2
VQFN32-9
T1525
BGT24MR2
Data Sheet
7
Revision 3.1, 2014-03-25
BGT24MR2
Silicon Germanium 24 GHz Twin IQ Receiver MMIC
Features
IFQ 2
IFQX 2
90°
LO
B uffer
PPF *
LNA
RFIN2
TEMP
SENSOR
TE MP
0°
IFI 2
LOIN
P ower
S plitter
IFQ1
IFIX 2
IFQX 1
SPI
3
S I CS CLK
90°
LO
B uffer
PPF *
LNA
RFIN 1
0°
IFI 1
IFIX 1
* Poly Phase Filter
BGT24MR2_Chip_BID.vsd
Figure 1
Data Sheet
BGT24MR2 Block Diagram
8
Revision 3.1, 2014-03-25
BGT24MR2
Silicon Germanium 24 GHz Twin IQ Receiver MMIC
Electrical Characteristics
2
Electrical Characteristics
2.1
Absolute Maximum Ratings
TA = -40 °C to 105 °C; all voltages with respect to ground, positive current flowing into pin (unless otherwise
specified)1)
Table 1
Absolute Maximum Ratings
Parameter
Symbol
Values
Min.
Typ.
Max.
Unit
Note / Test Condition
Supply voltage
VCC
-0.3
–
3.6
V
–
DC voltage at Pins RFIN1,
RFIN2, LOIN
VDCRF
0
–
0
V
MMIC provides short circuit
to GND for all RF Pins
DC voltage at Pins IFI1/2,
IFIX1/2, IFQ1/2, IFQX1/2
VDCIF
0
–
Vcc
V
–
DC current into Pins IFI1/2,
IFIX1/2, IFQ1/2, IFQX1/2
IIF
-8.5
–
3.5
mA
max. values indicate
current due to short circuit
to GND and Vcc
respectively
DC voltage at Pin TEMP
VDCTEMP
-0.3
–
3.6
V
–
DC current into Pin TEMP
ITEMP
-1
–
1.5
mA
max. values indicate
current due to short circuit
to GND and Vcc
respectively
DC voltage at SPI input Pins
SI, CLK, CS
VDCSPIIN
-0.3
–
3.6
V
–
–
–
3
mA
–
DC current into SPI input Pins ISPIIN
SI, CLK, CS
RF input power into Pins
RFIN1, RFIN2
PRF
–
–
0
dBm
–
LO input power into Pin LOIN
PLO
–
–
10
dBm
–
Total power dissipation
PDISS
–
–
500
mW
With BIST deactivated
Junction temperature
TJ
-40
–
150
°C
–
Ambient temperature range
TA
-40
–
105
°C
TA = Package soldering
point
Storage temperature range
TSTG
-40
–
150
°C
–
Attention: Stresses exceeding the max. values listed here may cause permanent damage to the device.
Exposure to absolute maximum rating conditions for extended periods may affect device
reliability. Maximum ratings are absolute ratings; exceeding only one of these values may
cause irreversible damage to the integrated circuit.
1) Not subject to production test, specified by design
Data Sheet
9
Revision 3.1, 2014-03-25
BGT24MR2
Silicon Germanium 24 GHz Twin IQ Receiver MMIC
Electrical Characteristics
2.2
Thermal Resistance
Table 2
Thermal Resistance
Parameter
Symbol
1)
Junction - soldering point
RthJS
Values
Min.
Typ.
Max.
–
–
40
Unit
Note / Test Condition
K/W
–
Unit
Note / Test Condition
1) For calculation of RthJA please refer to application note thermal resistance
2.3
ESD Integrity
Table 3
ESD Integrity
Parameter
ESD robustness, HBM
Symbol
1)
2)
ESD robustness, CDM
Values
Min.
Typ.
Max.
VESD-HBM
-1
–
1
kV
All pins
VESD-CDM
-500
–
500
V
All pins
1) According to ANSI/ESDA/JEDEC JS-001 (R = 1.5kΩ, C = 100pF) for Electrostatic Discharge Sensitivity Testing, Human
Body Model (HBM)-Component Level
2) According to JEDEC JESD22-C101 Field-Induced Charged Device Model (CDM), Test Method for Electrostatic-DischargeWithstand Thresholds of Microelectronic Components
Data Sheet
10
Revision 3.1, 2014-03-25
BGT24MR2
Silicon Germanium 24 GHz Twin IQ Receiver MMIC
Electrical Characteristics
2.4
Measured RF Characteristics
2.4.1
Power Supply
Table 4
Typical Characteristics TA = -40 .. 105 °C
Symbol
Parameter
Values
Min.
Typ.
Max.
Unit
Note /
Test Condition
Supply voltage
VCC
3.135
3.3
3.465
V
–
Supply current
ICC
70
90
120
mA
–
Unit
Note /
Test Condition
GHz
–
2.4.2
RX Section
Table 5
Typical Characteristics TA = -40 .. 105 °C, f = 24.0 .. 24.25 GHz1)
Parameter
Symbol
Values
Min.
Typ.
Max.
–
24.25
RFIN and LOIN frequency
range
fRFIN, fLOIN
24.0
RFIN and LOIN port
impedance2)
ZRFIN1
ZRFIN2
ZLOIN
–
14.0-j4.8 –
14.9-j6.3
27.3+j9.9
Ω
Typical value at
24.125GHz and
VSWR ≤ 2:1
RFIN and LOIN VSWR
VSWRRFIN,
VSWRLOIN
–
–
2:1
–
At source port of off
chip compensation
network as proposed
IF frequeny range
fIF
0
–
10
MHz
–
IF 1/f corner frequency
fc
–
10
20
kHz
–
IF port impedance
850
1000
1150
Ω
–
Leakage LOIN to RFIN
ZIF
LLOIN-RFIN
–
–
-30
dBm
Parameter based on
IFX eval board
design
Isolation RFIN1 to RFIN2
IRFIN1-RFIN2
30
–
–
dB
Parameter based on
IFX eval board
design
LOIN input power
PLOIN
-7
–
3
dBm
–
Voltage conversion gain3)
GC
19
26
31
dB
RLOAD,IF > 10kΩ
LNA gain reduction
ΔGCLG
3
5
8
dB
–
SSB Noise figure
NFSSB
–
12
20
dB
Single sideband at
100kHz
1dB input compression
IP-1dB
-17
-12
–
dBm
–
3‘rd order input intercept point
IIP3
-8
-4
–
dBm
–
Data Sheet
11
Revision 3.1, 2014-03-25
BGT24MR2
Silicon Germanium 24 GHz Twin IQ Receiver MMIC
Electrical Characteristics
Table 5
Typical Characteristics TA = -40 .. 105 °C, f = 24.0 .. 24.25 GHz1) (cont’d)
Symbol
Parameter
Values
Min.
Typ.
Max.
Unit
Note /
Test Condition
Quadrature phase imbalance
εP
-10
–
10
deg
–
Quadrat. amplitude imbalance
εA
-1
–
1
dB
–
1) Performance based on Application Circuit Figure 2 on Page 13, Cross Section of Application Board, Compensation
Structures and Application Board Layout Figure 4 on Page 18ff and Footprint Figure 8 on Page 21
2) Guaranteed by device design
3) Lowest gain at high temperature, highest gain at low temperature
2.5
Temperature Sensor
Monitoring of the chip temperature is provided by the on-chip temperature sensor which delivers temperatureproportional voltage to the TEMP output.
Table 6
Typical Characteristics Temperature Sensor TA = -40 .. 105 °C1)
Parameter
Symbol
Values
Unit
Note / Test Condition
Min.
Typ.
Max.
-40
–
105
°C
–
Temperature range
TTSENS
Output temperature voltage
VOUT,TEMP –
1.50
–
V
@ 25°C
Sensitivity
STSENS
–
4.5
–
mV/K
–
Overall accuracy error
ErrTSENS
–
–
±15
K
–
1) all voltages with respect to ground, positive current flowing into pin (unless otherwise specified)
Data Sheet
12
Revision 3.1, 2014-03-25
BGT24MR2
Silicon Germanium 24 GHz Twin IQ Receiver MMIC
Application Circuit and Block Diagram
3.1
Application Circuit Schematic
SI
CLK
CS
24
VEE
25
LOIN
26
VEE
TEST PIN
TEST PIN
n.c.
5)
1)
Application Circuit and Block Diagram
1)
3
23
22
21
20
19
18
C3
1μF
VCC
17
5)
IFIX2
IFI1
29
14
IFI2
IFQ1
30
13
IFQ2
IFQX1
31
12
IFQX2
VEE
32
11
VEE
3
4
6
5
C1
1μF
VCC
7
8
9
10
n.c.
4)
n.c.
2
4)
15
VEE
28
RFIN2
IFIX1
VEE
n.c.
VEE
16
RFIN1
27
VEE
TEMP
1
2)
3)
C2
470μF
2)
1) Connect test pin 24 and 25
2) Galvanic connection of VCC pins on silicon (pin 5, 6 and 17)
3) Optional value: according to quality of supply voltage (C2)
4) Recommendation: Connect pin 1 and 10 to VEE for better RF performance
5) Floating pin 16 and 26 - do not connect with any other pin
BGT24MR2_Appl_BID.vsd
Figure 2
Data Sheet
Application Circuit with Chip Outline (Top View)
13
Revision 3.1, 2014-03-25
BGT24MR2
Silicon Germanium 24 GHz Twin IQ Receiver MMIC
Application Circuit and Block Diagram
Table 7
Bill of Materials
Part Number
Part Type
Manufacturer
Size
Comment
C1 ... C3
Chip capacitor
Various
Various
–
Data Sheet
14
Revision 3.1, 2014-03-25
BGT24MR2
Silicon Germanium 24 GHz Twin IQ Receiver MMIC
Application Circuit and Block Diagram
3.2
Pin Description
Table 8
Pin Definition and Function
Pin No.
Name
Function
1
n.c.
Not connected
2
VEE
Ground
3
RFIN1
RF input downconverter 1
4
VEE
Ground
5
VCC
Supply voltage
6
VCC
Supply voltage
7
VEE
Ground
8
RFIN2
RF input downconverter 2
9
VEE
Ground
10
n.c.
Not connected
11
VEE
Ground
12
IFQX2
Complementary quadrature phase IF output downconverter 2
13
IFQ2
Quadrature phase IF output downconverter 2
14
IFI2
In phase IF output downconverter 2
15
IFIX2
Complementary in phase IF output downconverter 2
16
n.c.
Do not connect; DC coupled pin
17
VCC
Supply voltage
18
CS
Chip select input SPI (inverted)
19
CLK
Clock input SPI
20
SI
Data input SPI
21
VEE
Ground
22
LOIN
LO input
23
VEE
Ground
24
TEST PIN
Test pin; DC coupled pin
25
TEST PIN
Test pin; DC coupled pin
26
n.c.
Do not connect; DC coupled pin
27
TEMP
Temperature sensor output
28
IFIX1
Complementary in phase IF output downconverter 1
29
IFI1
In phase IF output downconverter 1
30
IFQ1
Quadrature phase IF output downconverter 1
31
IFQX1
Complementary quadratrue phase IF output downconverter 1
32
VEE
Ground
Data Sheet
15
Revision 3.1, 2014-03-25
BGT24MR2
Silicon Germanium 24 GHz Twin IQ Receiver MMIC
Application Circuit and Block Diagram
3.3
SPI
1.) Three signals control the serial peripheral interface of the BGT24MR2:
SI (Data); CLK (Clock); CS (Chip select)
2.) The data bits SI (MSB first) are read in the shift register with falling edge of the CLK signal.
Please make sure, that the data is present at least 10 ns before and at least 10 ns after the falling edge of the
clock signal.
3.) The CLK and CS signals are combined internally.
At least 20 ns before first rising edge of the first CLK signal CS needs to be in "low" state.
While the Data is read, CS has to remain in "low" state.
4.) When Data read in is finished, the shift register content will be written in the latch at the rising edge of the CS
signal. The time between the last falling edge of the CLK signal and the rising edge of the CS must be at least 20
ns.
Table 9
SPI Data Bit Description
Data Bit
Name
Description (Logic High)
Power ON State
15 (MSB)
GS
LNA Gain reduction
low
14
–
Not used
low
13
Test Bit
Test bit, must be low otherwise low
malfunction
12
Test Bit
Test bit, must be low otherwise low
malfunction
11
Test Bit
Test bit, must be low otherwise low
malfunction
10
Test Bit
Test bit, must be high
otherwise malfunction
high
9
Test Bit
Test bit, must be high
otherwise malfunction
high
8
Test Bit
Test bit, must be high
otherwise malfunction
high
7
Test Bit
Test bit, must be low otherwise low
malfunction
6
Test Bit
Test bit, must be low otherwise low
malfunction
5
Test Bit
Test bit, must be low otherwise low
malfunction
4
Test Bit
Test bit, must be high
otherwise malfunction
3
Test Bit
Test bit, must be low otherwise low
malfunction
2
Test Bit
Test bit, must be high
otherwise malfunction
Data Sheet
16
high
high
Revision 3.1, 2014-03-25
BGT24MR2
Silicon Germanium 24 GHz Twin IQ Receiver MMIC
Application Circuit and Block Diagram
Table 9
SPI Data Bit Description (cont’d)
Data Bit
Name
Description (Logic High)
Power ON State
1
Test Bit
Test bit, must be low otherwise low
malfunction
0
Test Bit
Test bit, must be low otherwise low
malfunction
BGT24MR2_SPI.vsd
Figure 3
Timing Diagram of the SPI
Table 10
SPI Timing and Logic Levels
Parameter
Symbol
Values
Unit
Min.
Typ.
Max.
Serial clock frequency
fSCLK
0
–
50
MHz
Serial clock high time
fSCLK(H)
10
–
–
ns
Serial clock low time
tSCLK(L)
10
–
–
ns
Chip select lead time
tCS(lead)
20
–
–
ns
Chip select lag time
tCS(lag)
20
–
–
ns
Data setup time
tSI(su)
10
–
–
ns
Data hold time
tSI(h)
10
–
–
ns
Low level (SI, CLK, CS)
VIN(L)
0
–
0.8
V
High level (SI, CLK, CS)
VIN(H)
2.0
–
VCC
V
Input capacitance (SI, CLK, CS)
CIN
–
–
2
pF
Input current (SI, CLK, CS)
IIN
-150
–
150
µA
Data Sheet
17
Revision 3.1, 2014-03-25
BGT24MR2
Silicon Germanium 24 GHz Twin IQ Receiver MMIC
Application Circuit and Block Diagram
3.4
Application Board
Blind-Vias
Vias
Ro4350B, 0.254mm
Copper
35um
FR4, 0.5mm
FR4, 0.25mm
BGT24MR2_Cross_Section_View.vsd
Figure 4
Cross-Section View of Application Board
Single-Ended RFIN
Single-Ended LOIN
0.50
0.50
0.30
0.35
0.30
0.30
All specified values in [mm]
Figure 5
Data Sheet
1.85
0.65
1.60
1.00
BGT24MR2_VQFN32-9-CS.vsd
Detail of Compensation Structure (valid for appl. board mat. Ro4350B, 0.254mm acc. to Fig. 4)
18
Revision 3.1, 2014-03-25
BGT24MR2
Silicon Germanium 24 GHz Twin IQ Receiver MMIC
Application Circuit and Block Diagram
Top layer (top view)
Mid1 and Bottom layer (top
view)
Mid2 layer (top view)
BGT24MR2_App_Board_Layout.vsd
Figure 6
Application Board Layout
Note: In order to achieve the same performance as given in this datasheet please follow the suggested PCBlayout. The compensation structure is critical for RF performance. Via holes as recommended on one of next
pages (not shown above).
Data Sheet
19
Revision 3.1, 2014-03-25
BGT24MR2
Silicon Germanium 24 GHz Twin IQ Receiver MMIC
Application Circuit and Block Diagram
3.5
Equivalent Circuit Diagram of MMIC Interfaces
Pin 12, 13, 14, 15,
28, 29, 30, 31
Pin 3, 8, 22
VCC
400Ω
RFIN1, RFIN2,
LOIN
IFx
VEE
VEE
Pin 27
Pin 18, 19, 20
VCC
VCC
CS, CLK, SI
TEMP
54kΩ
40Ω
1500Ω
VEE
VEE
Tolerance of all resistors +/- 20%
BGT24MR2_ESB.vsd
Figure 7
Data Sheet
Equivalent Circuit Diagram of MMIC Interfaces
20
Revision 3.1, 2014-03-25
BGT24MR2
Silicon Germanium 24 GHz Twin IQ Receiver MMIC
Physical Characteristics
4
Physical Characteristics
4.1
Package Footprint
Copper
4.3
Solder Mask
3.9
Vias
3.2
0.85
Pastefree
Area
3.3
2.9
2.2
0.1
1.0
0.5
0.2
PIN 1
0.3
0.1
0.7
0.3
All specified values in [mm]
Figure 8
Data Sheet
BGT24MR2_VQFN32-9-FP.vsd
Recommended Footprint and Stencil Layout for the VQFN32-9 Package
21
Revision 3.1, 2014-03-25
BGT24MR2
Silicon Germanium 24 GHz Twin IQ Receiver MMIC
Physical Characteristics
4.2
Reflow Profile
Soldering process qualified during qualification with “Preconditioning MSL-3: 30°C. 60%r.h., 192h, according to
JEDEC JSTD20”.
Reflow Profile recommended by Infineon Technologies AG
(based on IPC/JEDEC J-STD-020C)
BGT24MR2_Reflow_Profile.vsd
Figure 9
Data Sheet
Reflow Profile for BGT24MR2 (VQFN32-9)
22
Revision 3.1, 2014-03-25
BGT24MR2
Silicon Germanium 24 GHz Twin IQ Receiver MMIC
Physical Characteristics
4.3
Package Dimensions
All specified values in [mm]
BGT24MR2_VQFN32-9-PO.vsd
Figure 10
Package Outline (Top, Side and Bottom View)
BGT24MR2_VQFN32-9_ML.vsd
Figure 11
Data Sheet
Marking Layout VQFN32-9
23
Revision 3.1, 2014-03-25
BGT24MR2
Silicon Germanium 24 GHz Twin IQ Receiver MMIC
Physical Characteristics
All specified values in [mm]
BGT24MR2_VQFN32-9_CT.vsd
Figure 12
Data Sheet
Tape of VQFN32-9
24
Revision 3.1, 2014-03-25
w w w . i n f i n e o n . c o m
Published by Infineon Technologies AG