Singapore
Slovakia
Slovenia
South Africa
South Korea
Spain
Sweden
Switzerland
Syria
Taiwan
Thailand
Turkey
UAE
Ukraine
United Kingdom
Uruguay
USA
Venezuela
Vietnam
Yemen
Weidmuller is the leading manufacturer of components
for electrical connection technology to transmit energy,
signals and data. The Weidmuller product portfolio
ranges from terminal blocks, PCB connectors and
terminals, protected ­components, Industrial Ethernet
components, I/O components and relay sockets to
power supplies and overvoltage protection ­modules
suitable for all applications. Assemble Services, marking
solutions with a variety of tools and software systems,
round off the range. As an OEM supplier, the company
sets global standards in the field of electrical connection
technology.
11
Catalog
Iran
Ireland
Israel
Italy
Japan
Jordan
Kazakhstan
Kuwait
Latvia
Lebanon
Lithuania
Luxembourg
Macedonia
Malaysia
Malta
Mexico
Montenegro
Netherlands
New Zealand
Norway
Oman
Paraguay
Peru
Philippines
Poland
Portugal
Qatar
Romania
Russia
Saudi Arabia
Serbia
11
Power Delivery and Protection Solutions
Argentina
Australia
Austria
Azerbaijan
Bahrain
Belarus
Belgium
BosniaHerzegovina
Brazil
Bulgaria
Canada
Chile
China
Colombia
Costa Rica
Croatia
Czech Republic
Denmark
Ecuador
Egypt
Estonia
Finland
France
Germany
Greece
Hong Kong
Hungary
Iceland
India
Indonesia
CATALOG
www.weidmuller.com
Power Delivery and Protection Solutions
Catalog
Weidmuller, Canada
10 Spy Court
Markham, Ontario L3R 5H6
Telephone: (800) 268-4080
Facsimile: (877) 300-5635
Email:info1@weidmuller.ca
Website:www.weidmuller.ca
Weidmuller, Mexico
Blvd. Hermanos Serdán 698,
Col. San Rafael Oriente
Puebla, Puebla, Mexico
C.P. 72029
Telephone: 01 222 2686267
Facsimile: 01 222 2686219
Email:clientes@weidmuller.com.mx
Website:www.weidmuller.com.mx
Weidmuller, United States
821 Southlake Blvd.
Richmond, Virginia 23236
Telephone: (800) 849-9343
Facsimile: (804) 379-2593
Email:info@weidmuller.com
Website:www.weidmuller.com
010/11 • XM • LIT0803
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
Contents
Page
Power Distribution Blocks —WPDB
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Product Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Fuse Terminal Blocks —WSI
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Product Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Power Delivery Products
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
INSTAPOWER—Single Phase Input Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
PRO-M—Single Phase Input Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
PRO-M—Three Phase Input Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Diode Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
PRO-H Series—Single Phase Input Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
PRO-H Series—Diode Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
connectPower—Single Phase Input Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
connectPower—Three Phase Input Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
connectPower—Diode Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
connectPower DC-DC Converters
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Product Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
connectPower Battery Back Up Unit for DC Power Management
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Product Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Electronic Circuit Protection
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Product Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Branch Rated Circuit Protection
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
9926 Series—AC Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
9926 Series—AC Version with Auxiliary and Alarm Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
9926 Series—DC Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Supplemental Circuit Protection
9926 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
9926 Series with Auxiliary and Alarm Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
9926 Series—Ground Fault Current Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
9926 Series—Mounting Options and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
CB4200 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
CB2200 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
CB9100 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Overvoltage Protection — MCZ
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Product Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Surge Protection — MTL
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
SD Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
SLP Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
MA15 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
TP48 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
DIN-Rail Receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
1
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
We i d m u l l e r C a t a l o g s a t a G l a n c e
Catalog 1:
Modular Terminal Blocks
Catalog 6:
Tools
• Z-Series (Tension clamp)
• P-Series (Push-in)
• W-Series (Screw clamp)
• I-Series (IDC)
• Stud Style (Screw clamp)
• Power Distribution Blocks and Fuse Blocks
• Cutting
• Stripping
• Crimping
• Screwdrivers
Catalog 2:
PCB Terminals and Connectors
Catalog 7:
Marking Systems
• Space Saving Technologies
• Wide Variety of Clamping Technologies
• Pitches Ranging from 3.50 mm to 15.00 mm
• Orientations Ranging from 90˚ to 270˚
• Terminal Markers
• Wire and Cable Markers
• Device and Equipment Markers
• Printing Systems and Software
Catalog 3:
RockStar®– Heavy Duty Connectors
Catalog 8:
Sensor Actuator Interface
• Inserts
• Modular System
• Housings IP65 and IP69K
• Cable Glands
• SAI Passive Blocks
• SAI Universal
• SAI ASI
• Cables and Connectors
Catalog 4.1:
Analog Signal Conditioning
Catalog 9:
Industrial Ethernet
• Intrinsically Safe Conditioners
• Signal Converters and Monitoring Devices
• Indicators and Configurable Displays
• Fieldbus Distribution Boxes
• Unmanaged Switches
• Managed Switches
• Routers
• Media Converters
Catalog 4.2:
Relays and Optocouplers
Catalog 10:
Connectivity Solutions Catalog
• Mechanical Relays
• Solid-State (opto) Relays
• Power Solid-State Relays
• Multifunction Relays and Timers
• Short Form Catalog
• Product Overview
Catalog 4.4:
Surge Protection
Catalog 11:
Power Delivery and
Protection Solutions
• Surge Protection for Low-Voltage
• Surge Protection for Instrumentation and Control
• Surge Protection for Data Interfaces
• Surge Protection for Photovoltaic Systems
• Cutting
• Power Supplies
• DC/DC Converters
• Automatic Machines
• Ferrules
®
• JACKPAC IP67
®
• SteadyTEC
• IE Connectors
• Accessories
• Battery Back-up Units
• Diodes and Overvoltage
• Protection
Catalog 4.5:
Interface Units and PLC Solutions
Catalog 12:
Wireless Connectivity Solutions
• Interface Units
• PLC Interfaces – H-, R and S-System
• Byte Precabling Solution
• Wireless Ethernet
• Wireless Gateways
• Wireless Transceivers
• Antennas and Accessories
Catalog 5:
Enclosures and Cable Glands
CD ROM
• Pdf files of All Master Catalogs, Brochures, Datasheets
• Enclosures
• Cable Glands
• Cabtite (Cable Entry System)
2
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
I n t ro d u c t i o n — P o w e r D i s t r i b u t i o n B l o c k s
Power Distribution Blocks
WPDB
Now you can manage multiple load connections and a wide
range of wire sizes with Weidmuller’s Power Distribution blocks.
By using the best materials and the best technology, Wedimuller
provides the safest and most innovative connections available
in a wide area of industrial applications, including; machinery,
material handling, building/installation and power conditioning.
These DIN-rail mountable blocks combine installed cost savings
over traditional methods, high short-circuit protection, and
application flexibility. Weidmuller’s Power Distribution Blocks
deliver power and performance – without compromising safety
requirements.
• Space-saving design
• For use with a wide range of wire sizes
• SCCR rated* (UL 508-A, 100kA)
• IEC finger-safe design
• IP20 class protection
• For DIN-rail or direct mounting
* when used with fuses
508A 100kA
3
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
Power Distribution Blocks
WPDB 70 1-1
WPDB 70 1-1 AL
Type
WPDB 70 1-1
WPDB 70 1-1 AL
WPDB 70/35 1-4
WPDB 70/35 1-4 AL
Part No.
1879470000
1879460000
Type
WPDB 70/35 1-4
WPDB 70/35 1-4 AL
WPDB 185 1-1
WPDB 185 1-1 AL
Part No.
1879360000
1879480000
Type
WPDB 185 1-1
WPDB 185 1-1 AL
Part No.
1879410000
1879400000
Technical Data
Housing material
PA 66/6
Flammability class
UL 94 V0
Conductor
WPDB 70 1-1: Copper (75°C Cu wire only)
WPDB 70 1-1 AL: Aluminum (90°C Cu/Al wire)
Contact material
WPDB 70 1-1: Copper
WPDB 70 1-1 AL: Aluminum
Contact plating
Zinc
Technical Data
Housing material
PA 66/6
Flammability class
UL 94 V0
Conductor
WPDB 70/35 1-4: Copper (75°C Cu wire only)
WPDB 70/35 1-4 AL: Aluminum (90°C Cu/Al wire)
Contact material
WPDB 70/35 1-4: Copper
WPDB 70/35 1-4 AL: Aluminum
Contact plating
Zinc
Technical Data
Housing material
PA 66/6
Flammability class
UL 94 V0
Conductor
WPDB 185 1-1: Copper (75°C Cu wire only)
WPDB 185 1-1 AL: Aluminum (90°C Cu/Al wire)
Contact material
WPDB 185 1-1: Copper
WPDB 185 1-1 AL: Aluminum
Contact plating
Zinc
Current Rating
UL/CSA*
Current Rating
UL/CSA*
Current Rating
UL/CSA*
175 A at 600 V
175 A at 600 V
Line
Wire gauge, kcmil/AWG
Wire gauge, mm2
Number of poles
2/0…#14
70…2.5
1
Line
Wire gauge, kcmil/AWG
Wire gauge, mm2
Number of poles
2/0…#14
70…2.5
1
Load
Wire gauge, kcmil/AWG
Wire gauge, mm2
Number of poles
2/0…#14
70…2.5
1
Load
Wire gauge, kcmil/AWG
Wire gauge, mm2
Number of poles
#2…#14
35…2.5
4
Operating Specifications
Maximum temperature
Operating range
Storage temperature
100°C
-10°C…+60°C
-25°C…+60°C
Operating Specifications
Maximum temperature
Operating range
Storage temperature
100°C
-10°C…+60°C
-25°C…+60°C
335 A at 600 V
Line
Wire , kcmil/AWG
Wire gauge, mm2
Number of poles
400…#6
185…16
1
Load
Wire gauge, kcmil/AWG
Wire gauge, mm2
Number of poles
400…#6
185…16
1
Operating Specifications
Maximum temperature
Operating range
Storage temperature
100°C
-10°C…+60°C
-25°C…+60°C
Accessories
SK WSD-S
9008850000
(1.5-10 mm 9 piece set, Allen head screwdrivers)
SST WPDB
1879490000
(Accessory pin for fixing multi-pole block assemblies)
WEW 35/3
1879390000
(Pair of end brackets)
VK WPDB 1
1879370000
(Cap for spare 2/0 line connections)
VK WPDB 2
1879380000
(Cap for spare 350 kcmil line connections)
Accessories
SK WSD-S
9008850000
(1.5-10 mm 9 piece set, Allen head screwdrivers)
SST WPDB
1879490000
(Accessory pin for fixing multi-pole block assemblies)
WEW 35/3
1879390000
(Pair of end brackets)
VK WPDB 1
1879370000
(Cap for spare 2/0 line connections)
VK WPDB 2
1879380000
(Cap for spare 350 kcmil line connections)
Accessories
SK WSD-S
9008850000
(1.5-10 mm 9 piece set, Allen head screwdrivers)
SST WPDB
1879490000
(Accessory pin for fixing multi-pole block assemblies)
WEW 35/3
1879390000
(Pair of end brackets)
VK WPDB 1
1879370000
(Cap for spare 2/0 line connections)
VK WPDB 2
1879380000
(Cap for spare 350 kcmil line connections)
Marking Tags
KSW Strips, blank**
Marking Tags
KSW Strips, blank**
Marking Tags
KSW Strips, blank**
1629970000
*Based on NEC table 310-16 for 75°C copper wire
**Pre-printed strips standard with product. Custom strips
also available.
1629970000
*Based on NEC table 310-16 for 75°C copper wire
**Pre-printed strips standard with product. Custom strips
also available.
*Based on NEC table 310-16 for 75°C copper wire
**Pre-printed strips standard with product. Custom strips
also available.
4
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
1629970000
www.barr-thorp.com
Power Distribution Blocks
WPDB 185/35 1-8
WPDB 185/35 1-8 AL
Type
WPDB 185/35 1-8
WPDB 185/35 1-8 AL
WPDB 300 2-2
WPDB 300 2-2 AL
Part No.
1879430000
1879420000
Type
WPDB 300 2-2
WPDB 300 2-2 AL
WPDB 16/6 3/4
Part No.
1879450000
1879440000
Type
WPDB 16/6 3/4
Technical Data
Housing material
PA 66/6
Flammability class
UL 94 V0
Conductor WPDB 185/35 1-8: Copper (75°C Cu wire only)
WPDB 185/35 1-8 AL: Aluminum (90°C Cu/Al wire)
Contact material
WPDB 185/35 1-8: Copper
WPDB 185/35 1-8 AL: Aluminum
Contact plating
Zinc
Technical Data
Housing material
PA 66/6
Flammability class
UL 94 V0
Conductor
WPDB 300 2-2: Copper (75°C Cu wire only)
WPDB 300 2-2 AL: Aluminum (90°C Cu/Al wire)
Contact material
WPDB 300 2-2: Copper
WPDB 300 2-2 AL: Aluminum
Contact plating
Zinc
Technical Data
Housing material
Flammability class
Conductor
Current Rating
UL/CSA*
Current Rating
UL/CSA*
Current Rating
UL
310 A at 600 V
840 A at 600 V
Part No.
1939440000
Wemid
UL 94 V0
Copper (75ºC Cu wire only)
Contact material
Copper
Contact plating
80 A at 600 V
Line
Wire gauge, kcmil/AWG
Wire gauge, mm2
Number of poles
350…#6 / 2/0…#14
185…16 / 70…2.5
1
Line
Wire gauge, kcmil/AWG
Wire gauge, mm2
Number of poles
600…#4
300…25
2
Line
Wire gauge, kcmil/AWG
Wire gauge, mm2
Number of poles
14…6
2.5…16
1
Load
Wire gauge, kcmil/AWG
Wire gauge, mm2
Number of poles
#2…#14
35…2.5
8
Load
Wire gauge, kcmil/AWG
Wire gauge, mm2
Number of poles
600…#4
300…25
2
Load
Wire gauge, kcmil/AWG
Wire gauge, mm2
Number of poles
(2) 14…6/(4) x14…10
(2) 2.5...16/(4) 2.5…6
6
Operating Specifications
Maximum temperature
Operating range
Storage temperature
100°C
-10°C…+60°C
-25°C…+60°C
Operating Specifications
Maximum temperature
Operating range
Storage temperature
100°C
-10°C…+60°C
-25°C…+60°C
Operating Specifications
Maximum temperature
Operating range
Storage temperature
Accessories
SK WSD-S
9008850000
(1.5-10 mm 9 piece set, Allen head screwdrivers)
SST WPDB
1879490000
(Accessory pin for fixing multi-pole block assemblies)
WEW 35/3
1879390000
(Pair of end brackets)
VK WPDB 1
1879370000
(Cap for spare 2/0 line connections)
VK WPDB 2
1879380000
(Cap for spare 350 kcmil line connections)
Accessories
SK WSD-S
9008850000
(1.5-10 mm 9 piece set, Allen head screwdrivers)
SST WPDB
1879490000
(Accessory pin for fixing multi-pole block assemblies)
WEW 35/3
1879390000
(Pair of end brackets)
VK WPDB 2
1879380000
(Cap for spare 350 kcmil line connections)
VK WPDB 3
1880060000
(Cap for spare 600 kcmil line connections)
Accessories
SDK PZ1
(crosshead screwdriver, Pozidriv type)
SDK PZ2
(crosshead screwdriver, Pozidriv type)
SK-S 2.0-8.0
(7-piece hexagon wrench set)
Marking Tags
KSW Strips, blank**
Marking Tags
KSW Strips, blank**
Marking Tags
LogiMark Strips, blank
1629970000
*Based on NEC table 310-16 for 75°C copper wire
**Pre-printed strips standard with product. Custom strips
also available.
1629970000
120º C
9008530000
9008540000
9008860000
1882890000
*Based on NEC table 310-16 for 75°C copper wire
**Pre-printed strips standard with product. Custom strips
also available.
5
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
Power Distribution Blocks
WPDB 35-16/16 1-16
WPDB 70/16 1/10
Type
WPDB 35-16/16 1-16
Technical Data
Housing material
Flammability class
Conductor
WPDB 120/35-16-10 1/2-5-4
Part No.
1939450000
Type
WPDB 70/16 1/10
Part No.
1939460000
Wemid
UL 94 V0
Copper (75ºC Cu wire only)
Technical Data
Housing material
Flammability class
Conductor
Wemid
UL 94 V0
Copper (75ºC Cu wire only)
Contact material
Copper
Contact plating
Contact material
Copper
Contact plating
Current Rating
UL
115 A at 600 V
Current Rating
UL
Type
WPDB 120/35-16-10 1/2-5-4
Technical Data
Housing material
Flammability class
Conductor
Part No.
1939470000
Wemid
UL 94 V0
Copper (75ºC Cu wire only)
Contact material
Copper
Contact plating
115 A at 600V
Current Rating
UL/CSA
230 A at 600V
Line
Wire gauge, kcmil/AWG
Wire gauge, mm2
Number of poles
(1) 8…2/(1) 10…6
(1) 10…35/(1) 6…16
2
Line
Wire gauge, kcmil/AWG
Wire gauge, mm2
Number of poles
6…0
16…70
1
Line
Wire gauge, kcmil/AWG
Wire gauge, mm2
Number of poles
Load
Wire gauge, kcmil/AWG
Wire gauge, mm2
Number of poles
14…6
2.5…16
6
Load
Wire gauge, kcmil/AWG
Wire gauge, mm2
Number of poles
14…6
2.5…16
10
Load
Wire gauge, kcmil/AWG
(2) 14…2/(5) 14…6/(4) 14…8
Wire gauge, mm2
(2) 2.5…35/(5) 2.5…16/(4) 2.5…10
Number of poles
11
Operating Specifications
Maximum temperature
Operating range
Storage temperature
120º C
Accessories
SDK PZ2
(crosshead screwdriver, Pozidriv type)
SK-S 2.0-8.0
(7-piece hexagon wrench set)
Marking Tags
LogiMark Strips, blank
9008540000
Operating Specifications
Maximum temperature
Operating range
Storage temperature
Accessories
SK-S 2.0-8.0
(7-piece hexagon wrench set)
120º C
9008860000
9008860000
1882890000
Marking Tags
LogiMark Strips, blank
1882890000
Operating Specifications
Maximum temperature
Operating range
Storage temperature
Accessories
SD 1.0x5.5x150
(crosshead screwdriver, Pozidriv type)
SD 0.8x4.5x125
(crosshead screwdriver, Pozidriv type)
SK-S 2.0-8.0
(7-piece hexagon wrench set)
Marking Tags
LogiMark Strips, blank
6
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
2…4/0
35…120
1
120º C
9008350000
9009020000
9008860000
1882890000
Power Distribution Blocks
WPDB 185/35-16-10 1/2-5-4
Type
WPDB 185/35-16-10 1/2-5-4
Technical Data
Housing material
Flammability class
Conductor
WPDB 3 x 70/16 1/6
Part No.
1939480000
Wemid
UL 94 V0
Copper (75ºC Cu wire only)
Contact material
Copper
Type
WPDB 3 x 70/16 1/6
Technical Data
Housing material
Flammability class
Conductor
Contact material
WPDB 35/16/6/N 1/2/5/11
Part No.
1939490000
Wemid
UL 94 V0
Copper (75ºC Cu wire only)
Copper
Contact plating
Contact plating
Current Rating
UL/CSA
310 A at 600V
Current Rating
UL
Type
WPDB 35/16/6/N 1/2/5/11
Technical Data
Housing material
Flammability class
Conductor
115 A at 600V
Current Rating
UL
6…0
16…70
3x1
Line
Wire gauge, kcmil/AWG
Wire gauge, mm2
Number of poles
Load
Wire gauge, kcmil/AWG
(2) 14…2/(5) 14…6/(4) 16…8
Wire gauge, mm2
(2) 2.5…35/(5) 2.5…16/(4) 1.5…10
Number of poles
11
Load
Wire gauge, kcmil/AWG
Wire gauge, mm2
Number of poles
14…6
2.5…16
3x6
Load
Wire gauge, kcmil/AWG
Wire gauge, mm2
Number of poles
Operating Specifications
Maximum temperature
Operating range
Storage temperature
Operating Specifications
Maximum temperature
Operating range
Storage temperature
Accessories
SDK PZ1
(crosshead screwdriver, Pozidriv type)
SDK PZ2
(crosshead screwdriver, Pozidriv type)
SK-S 2.0-8.0
(7-piece hexagon wrench set)
Marking Tags
LogiMark Strips, blank
9008530000
Accessories
SK-S 2.0-8.0
(7-piece hexagon wrench set)
Copper
Contact plating
Line
Wire gauge, kcmil/AWG
Wire gauge, mm2
Number of poles
120º C
Wemid
UL 94 V0
Copper (75ºC Cu wire only)
Contact material
3/0…350
95…185
1
Line
Wire gauge, kcmil/AWG
Wire gauge, mm2
Number of poles
Part No.
1939510000
120º C
9008860000
9008540000
335 A at 600V
(3x1) 10…2/(3x5) 16…10/(3x2) 11…4
(3x1) 6…35/(3x5) 1.5…6/(3x2) 4…16
(3x1)/(3x5)/(3x2)
(1) 10…2/(4) 16…10/(6) 11…4
(1) 6…35/(4) 1.5…6/(6) 4…16
11
Operating Specifications
Maximum temperature
Operating range
Storage temperature
Accessories
SDK PZ1
(crosshead screwdriver, Pozidriv type)
SDK PZ2
(crosshead screwdriver, Pozidriv type)
120º C
9008530000
9008540000
9008860000
1882890000
Marking Tags
LogiMark Strips, blank
1882890000
Marking Tags
LogiMark Strips, blank
1882890000
7
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
Power Distribution Blocks
Tightening Torque Table
With recommended strip back lengths to
maintain IP20 rating
Part No.
Wire Strip
Hex
Product
Wire Hole
Back
Driver
Description
Range
Length
Size
1879460000
WPDB 70 1-1 AL
2/0…#14 AWG
0.75 in
1879470000
WPDB 70 1-1
(70…2.5 mm2)
(19.1 mm)
2/0…#14 AWG
1 in
(70…2.5 mm2)
(25.4 mm)
5 mm
5 mm
Wire
Product
Size*
Torque**
2/0…#1 AWG
100 lbs-in
(70…50 mm2)
(11.4 N-m)
#2…#6 AWG
80 lbs-in
Part No.
1939440000
Description
Wire Strip
Pozidriv
Back
Screwdriver
Size
Wire Size
Length
6…14 AWG
.47….35 in
WPDB
(16…2.5 mm2)
(12…9 mm)
16/6 3/4
10…14 AWG
.71….47 in
(35…16 mm2)
(9 N-m)
(6…2.5 mm2)
(18…12 mm)
#8…#14 AWG
35 lbs-in
6…14 AWG
.71….47 in
(10…2.5 mm2)
(3.9 N-m)
2/0…#1 AWG
100 lbs-in
(70…50 mm2)
(11.4 N-m)
#2…#6 AWG
80 lbs-in
1939450000
(16…2.5 mm2)
(18…12 mm)
WPDB
6…10 AWG
.47….39 in
35-16/16 1-16
(16…6 mm2)
(12…10 mm)
2…8 AWG
.59….55 in
(35…16 mm2)
(9 N-m)
(35…10 mm2)
(15…14 mm)
1879480000
WPDB 70/35 1-4 AL
#8…#14 AWG
35 lbs-in
6…14 AWG
.71….47 in
1879360000
WPDB 70/35 1-4
(10…2.5 mm2)
(3.9 N-m)
WPDB
(16…2.5 mm2)
(18…12 mm)
#2…#6 AWG
80 lbs-in
70/16 1/10
0…6 AWG
.63….59 in
(35…16 mm2)
(9 N-m)
(70…16)
(16…15 mm)
#8…#14 AWG
35 lbs-in
4/0…2 AWG
1.41…1.06 in
#2…#14 AWG
0.625 in
(35…2.5 mm2)
(15.9 mm)
350…#6 AWG
1.125 in
(35…2.5 mm2)
(28.5 mm)
4 mm
8 mm
1879420000 WPDB 185/35 1-8 AL
1879430000
WPDB 185/35 1-8
2/0…#14 AWG
0.875 in
(70…2.5 mm2)
(22.2 mm)
#2…#14 AWG
0.875 in
(35…2.5 mm2)
(22.2 mm)
1879400000
WPDB 185 1-1 AL
400…#6 AWG
1.3 in
1879410000
WPDB 185 1-1
(185…16 mm2)
(33 mm)
1879440000
WPDB 300 2-2 AL
600…#4 AWG
1.3 in
1879450000
WPDB 300 2-2
(300…25 mm2)
(33 mm)
5 mm
4 mm
10 mm
10 mm
1939460000
(10…2.5 mm2)
(3.9 N-m)
(120…35 mm2)
(29…27 mm)
350 kcmil…3/0 AWG
200 lbs-in
8…14 AWG
.47….39 in
(185…95 mm2)
(22.6 N-m)
WPDB
(10…2.5 mm2)
(12…10 mm)
2/0…#1 AWG
100 lbs-in
120/35-16-10 1/2-5-4
6…14 AWG
.47….39 in
(70…50 mm2)
(11.4 N-m)
(16…2.5 mm2)
(12…10 mm)
#2…#6 AWG
80 lbs-in
2…14 AWG
.47….39 in
1939470000
(35…16 mm2)
(9 N-m)
(35…2.5 mm2)
(12…10 mm)
2/0…#1 AWG
100 lbs-in
3/0…350 AWG
1.41…1.06 in
(70…50 mm2)
(11.4 N-m)
(185…95 mm2)
(29…27 mm)
#2…#6 AWG
80 lbs-in
8…16 AWG
.47….39 in
WPDB
(10…1.5 mm2)
(12…10 mm)
185/35-16-10 1/2-5-4
6…14 AWG
.47….39 in
(35…16 mm2)
(9 N-m)
#8…#14 AWG
35 lbs-in
1939480000
(10…2.5 mm2)
(3.9 N-m)
(16…2.5 mm2)
(12…10 mm)
#2…#6 AWG***
80 lbs-in***
2…14 AWG
.47….39 in
(35…16 mm2)
(9 N-m)
(35…2.5 mm2)
(12…10 mm)
#8…#14 AWG
35 lbs-in
0…4 AWG
.63….59 in
WPDB
(70…16 mm2)
(16…15 mm)
3 x 70/16 1/6
6…14 AWG
.47….39 in
(10…2.5 mm2)
(3.9 N-m)
400 kcmil…00 AWG
220 lbs-in
(185…70 mm2)
(24.9 N-m)
(16…2.5 mm2)
(12…10 mm)
0…#2 AWG
170 lbs-in
10…16 AWG
.47…35 in
(50…35 mm2)
(19.2 N-m)
#3…#6 AWG
130 lbs-in
1939490000
1939510000
(6…1.5 mm2)
(12…9 mm)
WPDB
4…11 AWG
.71…47 in
35/16/6/N 1/2/5/11
(25…16 mm2)
(14.7 N-m)
(16…4 mm2)
(18…12 mm)
600…500 kcmil AWG
310 lbs-in
2…10 AWG
.71…47 in
(35…6 mm2)
(18…12 mm)
(300…240 mm2)
(35.1 N-m)
400 kcmil…00 AWG
220 lbs-in
(185…70 mm2)
(24.9 N-m)
0…#2 AWG
170 lbs-in
(50…35 mm2)
(19.2 N-m)
#3…#4 AWG
130 lbs-in
(25 mm2)
(14.7 N-m)
PZ1
PZ2
PZ2
M4
M4
PZ2
M5
M6
SD 0.8x4.5x125
SD 0.8x4.5x125
SD 1.0x5.5x150
M6
SD 0.8x4.5x125
SD 0.8x4.5x125
SD 1.0x5.5x150
*Wire sizes based on AWG/kcmil standards with closest commercially available mm size.
**Torque values -0, +10%.
***Applies only to part number 1879420000 WPDB 185/35 1-8 AL.
8
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
M5
M3
PZ1
PZ2
PZ2
Torque
13.3…26.6 lbs-in
(1.5…3 Nm)
7.1…13.3 lbs-in
(0.8…1.5 Nm)
7.1…13.3 lbs-in
(0.8…1.5 Nm)
31…44.3 lbs-in
(3.5…5 Nm)
31…44.3 lbs-in
(3.5…5 Nm)
7.1…13.3 lbs-in
(0.8…1.5 Nm)
44.3 lbs-in
(5 Nm)
168.2 lbs-in
(19 Nm)
17.7 lbs-in
(2 Nm)
17.7 lbs-in
(2 Nm)
31 lbs-in
(3.5 Nm)
168.2 lbs-in
(19 Nm)
17.7 lbs-in
(2 Nm)
17.7 lbs-in
(2 Nm)
31 lbs-in
(3.5 Nm)
44.3 lbs-in
(5 Nm)
26.6 lbs-in
(3 Nm)
7.1 lbs-in
(0.8 Nm)
13.3 lbs-in
(1.5 Nm)
13.3 lbs-in
(1.5 Nm)
Power Distribution Blocks
Housing Dimensions
WPDB 70 1-1
WPDB 70 1-1 AL
WPDB 70/35 1-4
WPDB 70/35 1-4 AL
WPDB 185 1-1
WPDB 185 1-1 AL
9
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
Power Distribution Blocks
Housing Dimensions
WPDB 185/35 1-8
WPDB 185/35 1-8 AL
WPDB 300 2-2
WPDB 300 2-2 AL
10
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
Power Distribution Blocks
Housing Dimensions
WPDB 120/35-16-10 1/2-5-4
▲
▲
4.2
WPDB 16/6 3/4
▲
86
%
1
3
2
54
4
5
6
7
8
9
10
11
▲
29.9
4.2
WPDB 35-16/16 1-16
WPDB 185/35-16-10 1/2-5-4
86
%
61.5
1
3
2
4
5
6
7
8
9
10
11
▲
22.8
▲
22.8
▲
WPDB 70/16 1/10
▲
29.9
WPDB 3 x 70/16 1/6
29.9
▲
60.5
60.6
▲
▲
▲
52.5
17.5
11
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
Power Distribution Blocks
Housing Dimensions
60
▲
▲
WPDB 35/16/6/N 1/2/5/11
▲
62
N
N
N
L2
L1
N
L3
70.5
▲
▲
▲
▲
▲
5.3
Mounting Instructions
DIN Rail Mounting
Panel Mounting
12
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
Power Distribution Blocks
WPDB 120/35-16-10 1/2-5-4 and
WPDB 185/35-16-10 1/2-5-4
86 mm
Assembly instructions
M5
30 mm
62 mm
WPDB 35-16/16 1-16
6
M5
(3,5 N.m)
(31 In.Lbs)
PZ2
L1
WPDB 35/16/6/N 1/2/5/11
N
(2 N.m)
(17.5 In.Lbs)
L2
N
4
L3
N
N
WPDB 3x70/16 1/6
5
3
13
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
I n t ro d u c t i o n — F u s e Te r m i n a l B l o c k s
508A 200kA
WSI 25CC
WSI 4, 5 x 20 mm
WSI 25 10x38
WSI 4/2, 1 1/4" x 1/4"
WSI 25CC/LED
Fuse terminal 5 x 20 mm and 1 1/4" x 1/4"
with screw connection technology (clamping yoke)
WSI 25 10x38/LED
Weidmuller offers DIN rail mounted terminal blocks for the
popular 10.3 mm x 38 mm (13/32” x 1.5”) midget fuses.
Compact and touch safe, these terminals meet CSA, UL
and IEC requirements.
Features:
• CSA certified for 600 Vac, 30 A max.
• UL rated 600 Vac, 30 A max.
The new WSI 4 and 4/2 fuse terminal series offers you a
compact solution for implementing short-circuit and overload
protection utilizing 5 x 20 mm and 1 1/4" x 1/4" fuses.
Features:
• Standard screw clamp technology to accommodate
maximum 10 AWG conductors
• Blown fuse indication by means of LED voltage ranges
(10 - 250 V)
• 1, 2, 3 pole with or without indicator
• Combi-foot for mounting on TS 32 and TS 35 DIN-rails
(WSI 4/2 only)
• Mounting on 35 mm DIN rail
• Special interlocking of levers for multiple phase disconnection
• Only 17.8 mm wide per pole
• Large marking area to accommodate standard WS and
DEK markers
• Lever mechanism for quick and safe fuse
replacement
• Vented housing to reduce internal heating
and extend fuse life
• 3 W power dissipation maximum
• Two versions are available:
- WSI 25 10x38 accepts all types of 13/32" x 1.5" midget
fuses including CC type.
- WSI 25CC ONLY accepts CC type fuses which have
a typical interrupting capacity of 200kA and in compliance
to UL508A standard.
• Both version are available with or without LED
14
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
F u s e Te r m i n a l B l o c k s
25 mm2
WSI 25 10x38
For fuses 10x38
width x length x height with TS 35 x 7.5
mm
max. current / max. cond. cross-section A/mm2
max. clamping range
mm2
Technical data
Rated data
Rated voltage, adjacent terminal
Rated current
Rated cross-section
Rated isolation voltage
Power loss 1 pole / 2 pole / 3 pole
UL94 Flammability class
Approvals
Allowable power dissipation for standard version fuse
Allowable power dissipation for semi-conductor
protection version fuse
Interrupting Capacity
Clamped conductors (H05V/H07V)
Solid / stranded
Flexible / Flexible with wire end ferrule
Tightening torque range (clamping screw)
Stripping length
V
A
mm2
V
17.8 x 58 x 81
32 / 25
1.5 ... 25
25 mm2
WSI 25 CC
For fuses CC
17.8 x 58 x 81
32 / 25
1.5 ... 25
IEC 60947-7-3
IEC
UL
CSA
690
600
600
32
30
30
25
AWG 18 ... 4 AWG 18 ... 4
800
0.3 / 0.6 / 0.9
V-0
EN 60079-7
ar
IEC 60947-7-3
IEC
UL
CSA
690
600
600
32
30
30
25
AWG 18 ... 4 AWG 18 ... 4
800
0.3 / 0.6 / 0.9
V-0
EN 60079-7
ar
3W
4.3W (10mm2, 25A)
200kA
mm2
mm2
Nm
mm
Rated connection
1.5 ... 16 / 1.5 ... 16
0.75 … 25 / 0.75 … 25
2.0 ... 2.4
11
Rated connection
1.5 ... 16 / 1.5 ... 16
0.75 … 25 / 0.75 … 25
2.0 ... 2.4
11
Ordering data
Version
1 pole without LED
2 pole without LED
3 pole without LED
1 pole with LED
2 pole with LED
3 pole with LED
Type
WSI 25/1
WSI 25/2
WSI 25/3
WSI 25/1
WSI 25/2
WSI 25/3
10x38
10x38
10x38
10x38/LED
10x38/LED
10x38/LED
Qty.
12
6
4
12
6
4
Part No.
1966020000
1966090000
1966080000
1966060000
7940029427
7940029428
LED: 110-600Vac/dc, 2mA leakage
Note
Type
WSI 25/1
WSI 25/2
WSI 25/3
WSI 25/1
WSI 25/2
WSI 25/3
CC
CC
CC
CC/LED
CC/LED
CC/LED
Qty.
12
6
4
12
6
4
Part No.
1966050000
1966040000
1966030000
1966070000
7940029425
7940029426
Qty.
200
10
10
1
Part No.
1880100000
1044440000
1044450000
1044460000
LED: 110-600Vac/dc, 2mA leakage
Accessories
Marking Systems
2 pole ganging kit
3 pole ganging kit
Single phase bus bar (insulated)
Type
ESG 6/15 K MC WHITE
SET 2 POLE WSI 25
SET 3 POLE WSI 25
WQB 18MM/90 1METER
Qty.
200
10
10
1
Part No.
1880100000
1044440000
1044450000
1044460000
Type
ESG 6/15 K MC WHITE
SET 2 POLE WSI 25
SET 3 POLE WSI 25
WQB 18MM/90 1METER
Dimensions
15
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
F u s e Te r m i n a l B l o c k s
4 mm2
WSI 4
Fuse terminal 5 x 20 mm
Width/Length/Height with TS35x7.5
mm
Width/Length/Height with TS32x15
mm
Max. current / max. cond. cross-section A/mm2
Max. clamping range
mm2
Technical data
Rated data
Rated voltage / to adjoining terminal
V
Rated current / to adjoining terminal
A
Rated cross-section
mm2
Rated impulse voltage / Pollution severity
kV/Plug gauge IEC 60-947-1 / flammability class acc. UL94
Approvals
Clampable conductors (H05V/H07V)
Solid / stranded
Flexible / flexible w. wire end ferrule
Tightening torque range (clamping screw)
Stripping length / blade size
mm2
mm2
Nm
mm / -
2 clampable conductors of equal cross-section
Solid / stranded
Flexible / flexible w. wire end ferrule
mm2
mm2
Fuse terminal 1 1/4" x 1/4"
9.1 x 81.6 x 54
9.1 x 81.6 x 58.5
15 / 6
0.05 ... 6
8 x 50.7 x 39.4
15 / 4
0.05 ... 4
IEC 60947-7-3 / VDE 0100-537
IEC
UL
CSA
500
300
300
12
15
15
4
AWG 22…12 AWG 22…12
6 / 3
A3 / V-0
r
4 mm2
WSI 4/2
EN 60079-7
IEC 60947-7-3 / VDE 0100-537
IEC
UL
CSA
500
300
300
15
15
15
4
AWG 30…10 AWG 30…10
6 / 3
A3 / V-0
{
r
EN 50019
{
Rated connection
0.5…4 / 0.5…4
0.5…4 / 0.5…4
0.5…0.6 (M 3)
8 / 0.6 x 3.5
Rated connection
0.2…6
0.2…4
0.5…0.6 (M 3)
10 / 0.6 x 3.5
0.5…1.5
0.5…1.5 / 0.5…1.5
0.34…2.5
0.34…2.5 / 0.34…1.5
Ordering Data
Version
black Wemid
without LED
10 - 36 V
30 - 70 V
60 - 150 V
140 - 250 V
Type
WSI 4
WSI 4/LD
WSI 4/LD
WSI 4/LD
WSI 4/LD
10 - 36 V AC/DC
30 - 70 V AC/DC
60 - 150 V AC/DC
140 - 250 V AC/DC
Part No.
1886580000
1886590000
1886560000
1886570000
1886550000
Type
WSI 4/2
WSI 4/2/LD
WSI 4/2/LD
WSI 4/2/LD
WSI 4/2/LD
Part No.
Type
GZ 0.5A/F
GZ 1.0A/F
GZ 2.0A
GZ 3.0A
GZ 5.0A
GZ 7.0A
GZ 10.0A
GZ 12.5A/FF
Dummy fuse
Type
10 - 36 V AC/DC
30 - 70 V AC/DC
60 - 150 V AC/DC
140 - 250 V AC/DC
Part No.
1880430000
1880410000
1880440000
1880420000
1880390000
Accessories
Fuse cartridges 1 1/4" x 1/4" without indicator
33 kA breaking capacity
(F) = fast
Nominal voltage (V)
440 V
Fuse cartridges 5 x 20 mm (IEC 60127-2)
Rated voltage 250 V
0.25
Rated breakage capacity 1500 A
0.5
(at 250V / 50Hz / cos j = 0.7)
1
2
External jumper comb
A
A
A
A
Type
E 0.5
E1
E2
E3
E5
E7
E 10
E 12.5
Current [A]
A
A
A
A
A
A
A
A
quick-blow
quick-blow
quick-blow
quick-blow
Insulated
Type
Current
G 20/0.25A/F
G 20/0.5A/F
G 20/1A/F
G 20/2A/F
Type
Current
QB/WSI 4, 2-pole (8 mm)
QB/WSI 4, 3-pole (8 mm)
QB/WSI 4, 4-pole (8 mm)
[A]
[A]
15
15
15
Part No.
0430500000
0430600000
0430700000
0430900000
Part No.
0461100000
0461200000
0461300000
Type
Current [A]
QB/WSI 4/2, 10-pole (9 mm)
30
End plate / partition
black Wemid
Not Required
Current [A]
0.5
1
2
3
5
7
10
12.5
15
Current [A]
WAP WSI 4/2
Width [mm]
2.5
Part No.
0533800000
0525500000
0294500000
0295700000
0294600000
0295800000
0293900000
0245400000
1582770000
Part No.
Part No.
67603346
1880450000
End bracket
dark beige
EW35
0383560000 (TS 35)
EW35
EWK 1
0383560000 (TS 35)
0206160000 (TS32)
Screwdriver
Standard version
SD 0.6X3.5X100
9008330000
SD 0.6X3.5X100
9008330000
WS 12/6.5 MC
DEK 5/6 MC
1609920000
1609820000
WS 12/6.5 MC
DEK 5/6 MC
1609920000
1609820000
Marking systems
Tags
16
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
I n t ro d u c t i o n — P o w e r D e l i v e r y P ro d u c t s
Weidmuller offers a full range of power supplies for process control
and manufacturing automation applications.
INSTAPOWER
The INSTAPOWER family of power supplies is designed in compact and robust
housings for quick and easy TS35 DIN-rail mounting.
• Output voltage adjustable via potentiometer
• Wide-range input: 85…264 VAC /120…300 VDC
(24 W) / 110…370 VDC (25/48W)
• LED status indicator (25/48 W)
• Option for connecting in parallel
• International approvals for use world-wide
PRO-M Series
Weidmuller’s new compact PRO-M Series Switchmode Power Supplies
are optimized for machinery and offer a host of advantages.
•
•
•
•
•
Slim housings for space saving installation in the cabinet
DIN-rail mountable without any gap (no clearance necessary)
Operating temperature range of -25°C to +70°C
Autoselect Input for wide input range without any switch; for DC and AC voltages
Power boost of 120% enables inductive and capacitive loads;
additional starting capacity with up to a 2-minute boost
• Parallel connections allow simple power increase for up to
five units without diode module
• MTBF > 500,000 Hours
T-SERIES
The T-SERIES is a new generation of high performance DIN-rail mounted single-phase
power supplies designed to work reliably even under demanding factory floor conditions.
• Autoselect input eliminates the possibility of selecting the wrong input type
• Hazardous approvals - designed for use in process
automation and other harsh industrial environments.
• Operating temperature range of -25°C to +70°C
• Capable of cold start-up at full load at -25°C.
• Indefinite short circuit, overvoltage and overtemperature protection
• Remote On/Off
• Shock and vibration proof
• Variable output voltage automatically adjusts and overcomes voltage drops/dips
• Easy installation with detachable screw terminal block and snap-on DIN-rail mounting
• DC-OK signal and external shut down function
connectPower
The connectPower Series power supplies are available in both single phase
and three phase, and offer a number of features designed for demanding applications.
• Fulfill the demand for high quality power delivery solutions
• Designed with packaging advantages that include a rugged housing,
ability to panel mount, pluggable connectors and load sharing capability
• Feature up to 200% of maximum rated output for a specified
amount of time (power boost)
• Available with low residual ripple (< 10mV in some cases)
• Most models have universal AC/DC input
• Longer hold-up time for most models
• Feature greater galvanic isolation between
input and output
• Operate over a broader range of ambient temperatures
• Many available in 5, 12, 24, 28, and 48V versions
17
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
I N S TA P O W E R — S i n g l e P h a s e I n p u t S u p p l i e s
CP SNT 12W 0.5A
CP SNT 24W
Approvals:
r
®
LISTED
%
Diagram/Schematic Circuit Diagram
– secondary through plug-in jumpers ZQV
cross-connectable to other WAVE-modules
Ordering Data
Type
CP SNT 12W 0.5A
24 VDC / 0.5 A
Output voltage/maximum current
Technical Data
Input voltage
Minimum
Typical
Maximum
at 115 VAC
at 230 VAC
at 125 VDC
at 250 VDC
Input current
(Average values for reference only)
Input protection
Fuse
Inrush current
Overvoltage protection
Switching frequency
Efficiency at maximum load
Maximum ripple
Regulation
Load (10-100% load)
at input voltage
Overload protection
Maximum capacitance at output
Hold time
(Maximum output current following input loss)
Temperature
Humidity
Galvanic isolation
at 115 VAC
at 230 VAC
Storage
Operating
Operating temperature
Storage temperature
Input-output
Input/output to mounting rail
Input to ground
Output to ground
Wire size
Dimensions (L x W x H)
Weight
Mounting position
Clearance
Part No.
9918840024
Type
CP SNT
24 VDC
28 VDC
15 VDC
Part No.
24W
/1A
/1A
/ 1.5 A
9928890024
9928890028
9928890015
12 VDC / 1.5 A
5 VDC / 2 A
9928890012
9928890005
85 VAC, 120 VDC
115-230 VAC ± 10%, 50/60 Hz
85 VAC, 120 VDC
115-230 VAC ± 10%, 50/60 Hz
265 VAC, 300 VDC
260 mA RMS ± 20%
180 mA RMS ± 20%
125 mA ± 20%
65 mA ± 20%
265
480
270
280
140
2 A slow fuse (internal, not user serviceable)
Thermistor
2 A slow fuse (internal, not user serviceable)
Thermistor
Varistor
Varistor
100 kHz PWM
80%
100 kHz PWM
78%
0.1% RMS Vp-p
0.2%
0.3% RMS Vp-p
2% (12, 15 and 5 V) 0.5% (24 and 28 V)
0.2% 85 VAC - 265 VAC In
Overcurrent shutdown with automatic restart plus thermal
shutdown/short circuit
0.2%
Overcurrent shutdown with automatic restart plus thermal
shutdown/short circuit
8000 μF
30 ms
80 ms
8000 μF
35 ms
160 ms
-40°C…+85°C (-40°F…+185°F)
-20°C…+50°C (-4°F…+122°F) full rated load
Derating: 33% at 60°C (140°F)
20…85% RH non-condensing
-40°C…+85°C (-40°F…+185°F)
-20°C…+50°C (-4°F…+122°F) full rated load
Derating: 33% at 60°C (140°F)
20…85% RH non-condensing
20…90% RH
3 kV RMS
20…90% RH
3 kV RMS
4 kV RMS
1.5 kV RMS
4 kV RMS
1.5 kV RMS
500 V RMS
0.1…4.0 mm2 (26…12 AWG)
90 x 18 x 112.5 mm (3.54 x 0.71 x 4.43 in.)
140 g (0.311 lbs.)
Horizontal on mounting rail TS35
20 mm left and right
30 mm above and below if next to non-heat producing (lowpower) module
60 mm above and below if next to high heat producing module,
(i.e. another power supply)
500 V RMS
0.1…4.0 mm2 (26…12 AWG)
90.5 x 52 x 62.5 mm (3.56 x 2.05 x 2.46 in.)
160 g (0.35 lbs.)
Horizontal on mounting rail TS35
20 mm left and right
30 mm above and below if next to non-heat producing (lowpower) module
60 mm above and below if next to high heat producing module,
(i.e. another power supply)
CSA, UL 508 Listed, CE
CSA, UL 508 Listed, CE
VAC, 300 VDC
mA RMS ± 20%
mA RMS ± 20%
mA ± 20%
mA ± 20%
Approvals/Certifications
CSA Class 1 Div. 2 and Zone 2 for 9928890012 and 9928890024
UL 1310 (Class 2) for 9928890024
18
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
I N S TA P O W E R — S i n g l e P h a s e I n p u t S u p p l i e s
CP SNT 25W 5A
CP SNT 48W
Approvals:
r
%
®
LISTED
Diagram/Schematic Circuit Diagram
Ordering Data
Derating Curves
Derating Curves
Diagram/Schematic Circuit Diagram
Diagram/Schematic Circuit Diagram
Type
CP SNT 25W 5V 5A
4…8 VDC (adjustable via potentiometer) / 5 A
Output voltage/maximum current
Part No.
8754960000
Type
46…55 VDC (adjustabe via potentiometer)/1A
Technical Data
Input voltage
Minimum
Typical
85 VAC, 110 VDC
115/230 VAC
85 VAC, 110 VDC
115/230 VAC
Maximum
at 115 VAC
264 VAC, 370 VDC
950 mA
264 VAC, 370 VDC
950 mA
at 230 VAC
at 125 VDC
at 250 VDC
500 mA
500 mA
Fuse 2.5A (T) / 250V
Varistor
Fuse 2.5A (T) /250V
Varistor
Switching frequency
limited
100 kHz PWM
limited
100 kHz PWM
Efficiency at maximum load
Maximum ripple
78%
120 mVp-p
78%
120 mVp-p
1%
0.2%
105%…150% max. rated output power,
1%
0.2%
105%…150% max. rated output power,
automatic restart
>70%
35 ms
>50 ms
-40°C…+85°C (-40°F…+185°F)
-20°C…+50°C (-4°F…+122°F) full rated load
Derating: 33% at 60°C (140°F)
automatic restart
>75% / >78% / >80%
35 ms
>50 ms
-40°C…+85°C (-40°F…+185°F)
-20°C…+50°C (-4°F…+122°F) full rated load
Derating: 33% at 60°C (140°F)
20…85% RH non-condensing
20…90% RH
20…85% RH non-condensing
20…90% RH
3 kV RMS
4 kV RMS
3 kV RMS
4 kV RMS
1.5 kV RMS
500 V RMS
0.1…4.0 mm2 (26…12 AWG)
62.5 x 70 x 90.5 mm (2.46 x 2.76 x 3.56 in.)
Ca. 2 kg
Horizontal on mounting rail TS35
>30 mm above and below
1.5 kV RMS
500 V RMS
0.1…4.0 mm2 (26…12 AWG)
62.5 x 70 x 90.5 mm (2.46 x 2.76 x 3.56 in.)
Ca. 2 kg
Horizontal on mounting rail TS35
>30 mm above and below
Input current
(Average values for reference only)
Input protection
Fuse
Inrush current
Overvoltage protection
Regulation
Load (10-100% load)
at input voltage
Overload protection
Maximum capacitance at output
Hold time
(Maximum output current following input loss)
Temperature
Humidity
Galvanic isolation
at 115 VAC
at 230 VAC
Storage
Operating
Operating temperature
Storage temperature
Input-output
Input/output to mounting rail
Input to ground
Output to ground
Wire size
Dimensions (L x W x H)
Weight
Mounting position
Clearance
Approvals/Certifications
CSA / CE / UL 508 / cURus 60950 / GS
UL 1310 (Class 2)
Part No.
CP SNT 48W
9…15 VDC (adjustable via potentiometer)/4A 8754970000
15…28 VDC (adjustable via potentiometer)/2A 8739140000
8879230000
CSA / CE / UL 508 / cURus 60950 / GS
UL 1310 (Class 2)
19
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
NEW
PRO-M—Single Phase Input Supplies
CP M SNT 70W 24V 3A
CP M SNT 120W 24V 5A
Derating Curve
Temperature De-Rating
% of Nominal Current
120%
100%
80%
60%
40%
20%
0%
-10%
0%
10%
20%
30%
40%
50%
60%
70%
Ambient Temperature (°C)
Ordering Data
Type
CP M SNT 70W 24V 3A
Technical Data
Input Specifications
Rated input voltage
AC input voltage range
AC frequency range
DC input voltage range
AC current consumption
DC current consumption
Input fuse (internal)/Inrush current
Circuit Protection
Part No.
8951330000
Type
CP M SNT 120W 24V 5A
Part No.
8951340000
100...240 V AC (wide-range input)
85...264 V AC
47...63 Hz
80...370 V DC
0.80 A @ 230 V AC / 1.5A @ 115 V AC
0.25 A @ 370 V DC / 1.1 A @ 80 V DC
100...240 V AC (wide-range input)
85...264 V AC
47...63 Hz
80...370 V DC
1.3 A @ 230 V AC / 2.4 A @ 115 V AC
0.5 A @ 370 V DC / 1.8 A @ 80 V DC
yes/max. 20 A
2 A / DI, safety fuse
6 A, Char. B, Circuit breaker
2...4 A, Char. C, Circuit breaker
yes/max. 30 A
4 A / DI, safety fuse
6 A, Char. B, Circuit breaker
3...5 A, Char. C, Circuit breaker
24 V DC ± 1 %
24 V DC ± 1 %
22.5…29.5 V DC (adjustable via potentiometer on front)
100 mVss @ 24 V DC, IN
22.5…29.5 V DC (adjustable via potentiometer on front)
100 mVss @ 24 V DC, IN
3 A @ 55 °C
3.6 A @ 45 °C
3.3 A @ 50 °C
1.8 A @ 70 °C
3.6 A for 1 min, ED=5 %
5 A @ 55 °C
6.0 A @ 45 °C
5.5 A @ 50 °C
3.1 A @ 70 °C
6 A for 1 min, ED=5 %
88 % @ 230 V AC / > 85 % @ 115 V AC
> 0.5 @ 230 V AC / > 0.53 @ 115 V AC
89 % @ 230 V AC / > 85 % @ 115 V AC
> 0.5 @ 230 V AC / > 0.53 @ 115 V AC
> 100 ms @ 230 V AC / > 20 ms @ 100 V AC
yes
125 x 33 x 130
0.69 kg
> 100 ms @ 230 V AC / > 20 ms @ 100 V AC
yes
125 x 40 x 130
0.8 kg
CE, cURus, cULus Listed to UL508A and CSA C22.2 No. 107.1
CE, cURus, cULus Listed to UL508A and CSA C22.2 No. 107.1
Input
Screw connection
3 for L/N/PE
0.5 / 6
Output
Screw Connection
4 (++/--)
0.5 / 6
Input
Screw connection
3 for L/N/PE
0.5 / 6
Output
Screw Connection
5 (++/---)
0.5 / 6
0.5 / 2.5
26 / 12
0.5 / 2,.5
26 / 12
0.5 / 2.5
26 / 12
0.5 / 2.5
26 / 26
Output Specifications
Rated output voltage
Output voltage
Residual ripple, switching peaks
Rated output current @ Vrated
Continuous output current @ 24 V DC
Power boost @ 24 V DC, 60 °C
General Specifications
Efficiency
Power factor (approx.)
Mains buffering @ Irated
Parallel connection option
Length x Width x Height
Weight
mm
Approvals/Certifications
Connection Data
Type of connection
Number of terminals
Conductor cross-section, rigid min/max
Conductor cross-section, flexible min/max
Conductor cross-section, AWG/kcmil min/max
mm²
mm²
Accessories
* Recommendation applies only for AC operation; the max.
permissible operating voltage is to be observed in all cases!
* Recommendation applies only for AC operation; the max.
permissible operating voltage is to be observed in all cases!
20
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
NEW
PRO-M—Single Phase Input Supplies
CP M SNT 180W 24V 7.5A
CP M SNT 250W 24V 10A
Derating Curve
Temperature De-Rating
% of Nominal Current
120%
100%
80%
60%
40%
20%
0%
0%
10%
20%
30%
40%
50%
60%
65%
70%
Ambient Temperature (°C)
Ordering Data
Type
CP M SNT 180W 24V 7.5A
Technical Data
Input Specifications
Rated input voltage
AC input voltage range
AC frequency range
DC input voltage range
AC current consumption
DC current consumption
Input fuse (internal)/Inrush current
Circuit Protection
Part No.
8951350000
Type
CP M SNT 250W 24V 10A
Part No.
8951360000
100...240 V AC (wide-range input)
85...264 V AC
100...240 V AC (wide-range input)
85...264 V AC
47...63 Hz
80...370 V DC
1.9 A @ 230 V AC / 3.6 A @ 115 V AC
0.6 A @ 370 V DC / 2.6 A @ 80 V DC
yes
6 A / DI, safety fuse
16 A, Char. B, Circuit breaker
47...63 Hz
80...370 V DC
1.3 A @ 230 V AC / 2.5 A @ 115 V AC
0.9 A @ 370 V DC / 3.4 A @ 80 V DC
yes
6 A / DI, safety fuse
16 A, Char. B, Circuit breaker
5...10 A, Char. C, Circuit breaker
5...10 A, Char. C, Circuit breaker
24 V DC ± 1 %
24 V DC ± 1 %
22.5…29.5 V DC (adjustable via potentiometer on front)
100 mVss @ 24 V DC, IN
7.5 A @ 60 °C
9.0 A @ 45 °C
8.2 A @ 55 °C
5.6 A @ 70 °C
9 A for 1 min, ED=5 %
22.5…29.5 V DC (adjustable via potentiometer on front)
100 mVss @ 24 V DC, IN
10 A @ 60 °C
12 A @ 45 °C
11 A @ 55 °C
7.5 A @ 70 °C
12 A for 1 min, ED=5 %
90 % @ 230 V AC / > 85 % @ 115 V AC
> 0.5 @ 230 V AC / > 0.53 @ 115 V AC
> 40 ms @ 230 V AC / > 20 ms @ 100 V AC
yes
150 x 50 x 130
1.0 kg
90 % @ 230 V AC / > 85 % @ 115 V AC
> 0.98 @ 230 V AC / > 0.98 @ 115 V AC
> 40 ms @ 230 V AC / > 20 ms @ 100 V AC
yes
150 x 60 x 130
1.2 kg
CE, cURus, cULus Listed to UL508A and CSA C22.2 No. 107.1
CE, cURus, cULus Listed to UL508A and CSA C22.2 No. 107.1
Input
Screw connection
3 for L/N/PE
0.5 / 6
Output
Screw Connection
5 (++/---)
0.5 / 6
Input
Screw connection
3 for L/N/PE
0.5 / 6
Output
Screw Connection
5 (++/---)
0.5 / 6
0.5 / 2.5
26 / 12
0.5 / 2.5
26 / 12
0.5 / 2.5
26 / 12
0.5 / 2.5
26 / 12
Output Specifications
Rated output voltage
Output voltage
Residual ripple, switching peaks
Rated output current @ Vrated
Continuous output current @ 24 V DC
Power boost @ 24 V DC, 60 °C
General Specifications
Efficiency
Power factor (approx.)
Mains buffering @ Irated
Parallel connection option
Length x Width x Height
Weight
mm
Approvals/Certifications
Connection Data
Type of connection
Number of terminals
Conductor cross-section, rigid min/max
Conductor cross-section, flexible min/max
Conductor cross-section, AWG/kcmil min/max
mm²
mm²
Accessories
* Recommendation applies only for AC operation; the max.
permissible operating voltage is to be observed in all cases!
* Recommendation applies only for AC operation; the max.
permissible operating voltage is to be observed in all cases!
21
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
NEW
PRO-M—Single Phase Input Supplies
CP M SNT 500W 24V 20A
CP M SNT 1000W 24V 40A
Derating Curve
Temperature De-Rating
% of Nominal Current
120%
100%
80%
60%
40%
20%
0%
0%
10%
20%
30%
40%
50%
60%
65%
70%
Ambient Temperature (°C)
Ordering Data
Type
CP M SNT 500W 24V 20A
Technical Data
Input Specifications
Rated input voltage
AC input voltage range
AC frequency range
DC input voltage range
AC current consumption
DC current consumption
Input fuse (internal)/Inrush current
Circuit Protection
Part No.
8951370000
Type
CP M SNT 1000W 24V 40A
Part No.
8951380000
100...240 V AC wide-range input)
85...264 V AC
47...63 Hz
80...370 V DC
2.5 A @ 230 V AC / 4.9 A @ 115 V AC
1.6 A @ 370 V DC / 6.8 A @ 80 V DC
100...240 V AC (wide-range input)
85...264 V AC
47...63 Hz
80...370 V DC
4.9 A @ 230 V AC / 9.6 A @ 115 V AC
3.0 A @ 370 V DC / 13.5 A @ 80 V DC
yes
10 A / DI, safety fuse
20 A, Char. B, Circuit breaker
10...12 A, Char. C, Circuit breaker
yes
16 A / DI, safety fuse
25 A, Char. B, Circuit breaker
14...16 A, Char. C, Circuit breaker
24 V DC ± 1 %
24 V DC ± 1 %
22.5…29.5 V DC (adjustable via potentiometer on front)
100 mVss @ 24 V DC, IN
22.5…29.5 V DC (adjustable via potentiometer on front)
100 mVss @ 24 V DC, IN
20
24
22
15
24
40
48
44
30
48
Output Specifications
Rated output voltage
Output voltage
Residual ripple, switching peaks
Rated output current @ Vrated
Continuous output current @ 24 V DC
Power boost @ 24 V DC, 60 °C
General Specifications
Efficiency
Power factor (approx.)
Mains buffering @ Irated
Parallel connection option
Length x Width x Height
Weight
mm
A
A
A
A
A
@ 60 °C
@ 45 °C
@ 55 °C
@ 70 °C
for 1 min, ED=5 %
A
A
A
A
A
@ 60 °C
@ 45 °C
@ 55 °C
@ 70 °C
for 1 min, ED=5 %
> 90 % @ 230 V AC / > 85 % @ 115 V AC
> 0.98 @ 230 V AC / > 0.98 @ 115 V AC
> 90 % @ 230 V AC / > 85 % @ 115 V AC
> 0.98 @ 230 V AC / > 0.98 @ 115 V AC
> 40 ms @ 230 V AC / > 20 ms @ 100 V AC
yes
150 x 121 x 130
1.5 kg
> 40 ms @ 230 V AC / > 20 ms @ 100 V AC
yes
150 x 180 x 130
1.5 kg
CE, cURus, cULus Listed to UL508A and CSA C22.2 No. 107.1
CE, cURus, cULus Listed to UL508A and CSA C22.2 No. 107.1
Input
Screw connection
3 for L/N/PE
0.5 / 6
Output
Screw Connection
5 (++/---)
0.5 / 6
Input
Screw connection
3 for L/N/PE
0.5 / 6
Output
Screw Connection
5 (++/---)
0.5 / 16
0.5 / 2.5
26 / 10
0.5 / 2.5
26 / 10
0.5 / 2.5
26 / 10
2.5 / 10
26 / 6
Approvals/Certifications
Connection Data
Type of connection
Number of terminals
Conductor cross-section, rigid min/max
Conductor cross-section, flexible min/max
Conductor cross-section, AWG/kcmil min/max
mm²
mm²
Accessories
* Recommendation applies only for AC operation; the max.
permissible operating voltage is to be observed in all cases!
* Recommendation applies only for AC operation; the max.
permissible operating voltage is to be observed in all cases!
22
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
NEW
P R O - M — T h re e P h a s e I n p u t S u p p l i e s
CP M SNT3 120W 24V 5A
CP M SNT3 250W 24V 10A
Derating Curve
Temperature De-Rating
% of Nominal Current
120%
100%
80%
60%
40%
20%
0%
0%
10%
20%
30%
40%
50%
60%
65%
70%
Ambient Temperature (°C)
Ordering Data
Type
CP M SNT3 120W 24V 5A
Technical Data
Input Specifications
Rated input voltage
AC input voltage range
AC frequency range
DC input voltage range
AC current consumption
DC current consumption
Input fuse (internal)
Circuit Protection
Output Specifications
Rated output voltage
Output voltage
Residual ripple, switching peaks
Rated output current @ Vrated
Continuous output current @ 24 V DC
Part No.
8951390000
3 x 400...3 x 500 V AC (wide-range input)
3 x 320...3 x 575 V AC / 2 x 360...2 x 575 V AC
47...63 Hz
450...800 V DC (max. 500 V DC acc. to UL508)
0.5 A @ 3 x 500 V AC / 0.6 A @ 3 x 400 V AC
0.4 A @ 800 V DC / 0.7 A @ 450 V DC
no
2 A / DI, safety fuse
1...2 A, Char. C, Circuit breaker
no
2 A / DI, safety fuse
2...3 A, Char. C, Circuit breaker
24 V DC ± 1 %
22.5…29.5 V DC (adjustable via potentiometer on front)
24 V DC ± 1 %
22.5…29.5 V DC (adjustable via potentiometer on front)
100 mVss @ 24 V DC, IN
5 A @ 60 °C
6.0 A @ 45 °C
5.5 A @ 55 °C
100 mVss @ 24 V DC,IN
10 A @ 60 °C
12 A @ 45 °C
11 A @ 55 °C
7.5 A @ 70 °C
12 A for 1 min, ED=5 %
3.7 A @ 70 °C
6 A for 1 min, ED=5 %
General Specifications
Efficiency
Power factor (approx.)
Mains buffering @ Irated
90 % @ 3 x 500 V AC / > 90 % @ 3 x 400 V AC
> 0.75 @ 3 x 500 V AC / > 0.78 @ 3 x 400 V AC
> 25 ms @ 3 x 500 V AC / > 20 ms @ 3 x 400 V AC
mm
Weight
Part No.
8951400000
3 x 400...3 x 500 V AC (wide-range input)
3 x 320...3 x 575 V AC / 2 x 360...2 x 575 V AC
47...63 Hz
450...800 V DC (max. 500 V DC acc. to UL508)
0.25 A @ 3 x 500 V AC / 0.3 A @ 3 x 400 V AC
0.2 A @ 800 V DC / 0.4 A @ 450 V DC
Power boost @ 24 V DC, 60 °C
Parallel connection option
Length x Width x Height
Type
CP M SNT3 250W 24V 10A
yes
125 x 40 x 130
0.55 kg
90 % @ 3 x 500 V AC / > 90 % @ 3 x 400 V AC
> 0.75 @ 3 x 500 V AC / > 0.78 @ 3 x 400 V AC
> 25 ms @ 3 x 500 V AC / > 20 ms @ 3 x 400 V AC
yes
150 x 60 x 130
0.9 kg
CE, cURus, cULus Listed to UL508A and CSA C22.2 No. 107.1
CE, cURus, cULus Listed to UL508A and CSA C22.2 No. 107.1
Input
Screw connection
4 for L1/L2/L3/PE
0.5 / 6
0.5 / 2.5
Output
Screw Connection
5 (++/---)
0.5 / 6
0.5 / 2.5
Input
Screw connection
4 for L1/L2/L3/PE
0.5 / 6
0.5 / 2.5
Output
Screw Connection
5 (++/---)
0.5 / 6
0.5 / 2.5
26 / 12
26 / 12
26 / 12
26 / 12
Approvals/Certifications
Connection Data
Type of connection
Number of terminals
Conductor cross-section, rigid min/max
Conductor cross-section, flexible min/max
Conductor cross-section, AWG/kcmil min/max
mm²
mm²
Accessories
* Recommendation applies only for AC operation; the max.
permissible operating voltage is to be observed in all cases!
* Recommendation applies only for AC operation; the max.
permissible operating voltage is to be observed in all cases!
23
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
NEW
P R O - M — T h re e P h a s e I n p u t S u p p l i e s
CP M SNT3 500W 24V 20A
CP M SNT3 1000W 24V 40A
Derating Curve
Temperature De-Rating
% of Nominal Current
120%
100%
80%
60%
40%
20%
0%
0%
10%
20%
30%
40%
50%
60%
65%
70%
Ambient Temperature (°C)
Ordering Data
Type
CP M SNT3 500W 24V 20A
Technical Data
Input Specifications
Rated input voltage
AC input voltage range
AC frequency range
DC input voltage range
AC current consumption
DC current consumption
Input fuse (internal)
Circuit Protection
Part No.
8951410000
Type
CP M SNT3 1000W 24V 40A
Part No.
8951420000
3 x 400...3 x 500 V AC (wide-range input)
3 x 320...3 x 575 V AC / 2 x 360...2 x 575 V AC
47...63 Hz
450...800 V DC (max. 500 V DC acc. to UL508)
0.9 A @ 3 x 500 V AC / 1.1 A @ 3 x 400 V AC
0.7 A @ 800 V DC / 1.3 A @ 450 V DC
3 x 400...3 x 500 V AC (wide-range input)
3 x 320...3 x 575 V AC / 2 x 360...2 x 575 V AC
47...63 Hz
450...800 V DC (max. 500 V DC acc. to UL508)
1.8 A @ 3 x 500 V AC / 2.1A @ 3 x 400 V AC
1.4 A @ 800 V DC / 2.5A @ 450 V DC
no
2 A / DI, safety fuse
3...5 A, Char. C, Circuit breaker
no
4 A / DI, safety fuse
10 A, Char. B, Circuit breaker
6...8 A, Char. C, Circuit breaker
24 V DC ± 1 %
22.5…29.5 V DC (adjustable via potentiometer on front)
100 mVss @ 24 V DC, IN
24 V DC ± 1 %
22.5…29.5 V DC (adjustable via potentiometer on front)
100 mVss @ 24 V DC, IN
20
24
22
15
24
40
48
44
30
48
Output Specifications
Rated output voltage
Output voltage
Residual ripple, switching peaks
Rated output current @ Vrated
Continuous output current @ 24 V DC
Power boost @ 24 V DC, 60 °C
General Specifications
Efficiency
Power factor (approx.)
Mains buffering @ Irated
Parallel connection option
Length x Width x Height
Weight
mm
A
A
A
A
A
@ 60 °C
@ 45 °C
@ 55 °C
@ 70 °C
for 1 min, ED=5 %
A
A
A
A
A
@ 60 °C
@ 45 °C
@ 55 °C
@ 70 °C
for 1 min, ED=5 %
> 90 % @ 3 x 500 V AC / > 91 % @ 3 x 400 V AC
> 0.75 @ 3 x 500 V AC / > 0.78 @ 3 x 400 V AC
> 90 % @ 3 x 500 V AC / 92 % @ 3 x 400 V AC
> 0.75 @ 3 x 500 V AC / > 0.78 @ 3 x 400 V AC
> 25 ms @ 3 x 500 V AC / > 20 ms @ 3 x 400 V AC
yes
150 x 121 x 130
1.5 kg
> 25 ms @ 3 x 500 V AC / > 20 ms @ 3 x 400 V AC
yes
150 x 180 x 130
2.9 kg
CE, cURus, cULus Listed to UL508A and CSA C22.2 No. 107.1
CE, cURus, cULus Listed to UL508A and CSA C22.2 No. 107.1
Input
Screw connection
4 for L1/L2/L3/PE
0.5 / 6
0.5 / 2.5
26 /10
Input
Screw connection
4 for L1/L2/L3/PE
0.5 / 6
0.5 / 2.5
26 / 10
Approvals/Certifications
Connection Data
Type of connection
Number of terminals
Conductor cross-section, rigid min/max
Conductor cross-section, flexible min/max
Conductor cross-section, AWG/kcmil min/max
mm²
mm²
Output
Screw Connection
5 (++/---)
0.5 / 6
0.5 / 2.5
26 / 10
Output
Screw Connection
5 (++/---)
0.5 / 16
0.5 / 10
26 / 6
Accessories
* Recommendation applies only for AC operation; the max.
permissible operating voltage is to be observed in all cases!
* Recommendation applies only for AC operation; the max.
permissible operating voltage is to be observed in all cases!
24
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
I n t ro d u c t i o n — D i o d e M o d u l e s f o r R e d u n d a n c y
Redundancy, Load Sharing,
Increased Power Delivery
Weidmuller’s diode modules are designed
to enhance the ConnectPower series of
DC power supplies and provide a more
reliable Power Delivery Solution. They are
cost effective products that enable redundancy as well as load sharing between
power supplies, thus extending the useful
life of the power supply.
It is important to keep in mind that before
paralleling power supplies, their output
voltage must be calibrated to be within
±50mV of each other, and the parallel
connection must be positioned as close
as possible to the load.
Diode modules can increase the reliability
of a Power Delivery Solution by preventing current feedbacks between paralleled
power supplies.
25
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
I n t ro d u c t i o n — D i o d e M o d u l e s f o r R e d u n d a n c y
Parallel Connection for Increased Power Delivery
24VDC/20Amp
10Amp Power Supply
10Amp Power Supply
OUT
+V
+V
-V
-V
230VAC
230VAC
115VAC
115VAC
8710620000
CP DM 10
8708680000
CP SNT 250W 24V 10A
Input
24V=2x10A
Output
24V=20A
8708680000
CP SNT 250W 24V 10A
DC OK
L
N
• The amount of power needed is
provided by two power supplies
combined in parallel
PE
12
11
14
+V
DC OK
+V
-V
E1
-V
-V
-V
E2
L
N
PE
12
11
14
+V
+V
-V
-V
IN
24VDC/10Amp
24VDC/10Amp
• Diode modules provide galvanic
isolation between power supplies
Provide Uninterrupted DC Power with Redundancy and Fault Indication
(this example supplying 7A to load)
Diode Module
24VDC/7Amp
10Amp Power Supply
10Amp Power Supply
• Use status relays for remote alarm
indication
OUT
+V
+V
-V
-V
230VAC
230VAC
115VAC
115VAC
8708680000
CP SNT 250W 24V 10A
8710620000
CP DM 10
Input
24V=2x10A
Output
24V=20A
8708680000
CP SNT 250W 24V 10A
DC OK
L
N
PE
12
11
14
+V
DC OK
+V
-V
-V
E1
-V
-V
E2
L
N
PE
12
11
14
+V
+V
-V
-V
IN
24VDC/3.5Amp
24VDC/3.5Amp
Status Relays (Change-Over-Contact)
e.g. to PLC, IPC or Fieldbus
Status Relays (Change-Over-Contact)
e.g. to PLC, IPC or Fieldbus
• The amount of power needed is
provided by two power supplies
combined in parallel
Increase DC Power Delivery to Control Systems
(this example supplying 14A to load)
Diode Module
24VDC/14Amp
10Amp Power Supply
10Amp Power Supply
OUT
+V
+V
-V
-V
230VAC
230VAC
115VAC
115VAC
8708680000
CP SNT 250W 24V 10A
8710620000
CP DM 10
Input
24V=2x10A
Output
24V=20A
8708680000
CP SNT 250W 24V 10A
DC OK
L
N
• Use status relays for remote alarm
indication
PE
12
11
14
+V
DC OK
+V
-V
E1
-V
-V
-V
E2
L
N
PE
12
11
14
+V
+V
-V
-V
IN
24VDC/7Amp
24VDC/7Amp
Status Relays (Change-Over-Contact)
e.g. to PLC, IPC or Fieldbus
Status Relays (Change-Over-Contact)
e.g. to PLC, IPC or Fieldbus
• Under normal operating conditions,
the critical load is provided by both
the 10A and 3A power supply
Guarantee DC Power to Critical Loads
(this example supplying 3A to critical load)
24VDC/3Amp
10Amp Power Supply
24VDC/10Amp
Critical Loads
OUT
+V
+V
-V
-V
Diode Module
24VDC/10Amp
230VAC
115VAC
8708680000
CP SNT 250W 24V 10A
8710620000
CP DM 10
Input
24V=2x10A
Output
24V=20A
Status Relays (Change-Over Contact)
e.g. to PLC, IPC or Fieldbus
DC OK
L
N
PE
12
11
14
+V
+V
-V
E1
-V
-V
-V
E2
• If the larger power supply fails,
the critical load will continue to be
maintained by the 3A power supply
• This ensures uninterrupted power to
the critical load
IN
Non-critical Loads
24VDC/10Amp
Status Relays (Change-Over Contact)
e.g. to PLC, IPC or Fieldbus
12 11 10
V+ V+ V- V-
DC OK
8703660000
CP SNT 70A 24V 3A
24Amp Power Supply
24VDC/3Amp
L
N
PE
Note: Two power supplies in parallel must be calibrated to within ± 50 mv
of each other.
26
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
Diode Modules for Redundancy
CP DM 10
10A per Input Diode Module
CP DM 20
20A per Input Diode Module
Approvals:
% \
Derating Curve
Schematic
Schematic
3/5/10/20A
Output load / ambient temperature
+V
120
-V
+V
-V
Load (%)
100
80
60
40
20
E1
0
-10
0
10
20
30
40
50
60
70
E2 -V
E1
E2 -V
Ambient temperature (°C)
Type
CP DM 10
Ordering Data
Technical Data
Input
Input voltage
Input current
Output
Output voltage
Output current
General Specifications
Temperature
Operating
Storage
Efficiency under max. load
Mount onto mounting rail
Mounting position
Mounting
Weight
Dimensions (L x W x H)
Type of Connection
Clamping area input (nominal / min. / max.)
Clamping area output (nominal / min. / max.)
Indication signals
Voltage
Alarm
Fault Relay
Voltage
Current
Configuration
Other
Terminations
Set point
Voltage drop input-output
Fan
Input/output
Alarm contact
Qty.
1
Part No.
8710620000
Type
CP DM 20
Qty.
1
Part No.
8768650000
40 VDC max.
10 A per input max.
Vin - 0.5 typ.
20 A max.
40 VDC max.
20 A per input max.
Vin - 0.5 typ.
40 A max.
-10°C…+55°C (+14°F…+131°F)
-20°C…+85°C (-4°F…+185°F)
approx. 95.5% at 24 VDC
-10°C…+55°C (+14°F…+131°F)
-20°C…+85°C (-4°F…+185°F)
approx. 95% at 24 VDC
Mounting rail TS35 to DIN 50022
Horizontal
Clearance: side 2 4 cm; above/below 2 10 cm
Mounting rail TS35 to DIN 50022
Horizontal
Clearance: side 2 4 cm; above/below 2 10 cm
approx. 0.15 kg (0.33 lbs.)
125.0 x 55.5 mm x 110.0 (4.92 x 2.19 x 4.33 in.)
approx. 0.5 kg (1.1 lbs.)
125.0 x 55.5 mm x 110.0 (4.92 x 2.19 x 4.33 in.)
Screw
4 / 0.13 / 6 mm2 (12 / 26 / 10 AWG)
4 / 0.13 / 6 mm2 (12 / 26 / 10 AWG)
None
Screw
4 / 0.13 / 6 mm2 (12 / 26 / 10 AWG)
10.0 / 0.32 / 16.0 mm2 (8 / 22 / 6 AWG)
None
None
None
None
None
None
None
0.5 V typ.
None
None
None
None
None
0.5 V typ.
None
N/A
N/A
N/A
N/A
CE, cURus, cULus Listed to UL508 and CSA C22.2 No. 107.1
CE, cURus, cULus Listed to UL508 and CSA C22.2 No. 107.1
Approvals/Certifications
27
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
NEW
PRO-H Series—Single Phase Input Supplies
CP T SNT 70W 12V 6A
L (+)
N(-
CP T SNT 90W 24V 3.8A
+
AC
PE
CP T SNT 140W 12V 12A
DC
-
Ordering Data
Type
CP T SNT 70W 12V 6A
Technical Data
Input Specifications
Input voltage
Input voltage range
Input voltage frequency
Harmonic limits
Hold up time
Inrush current
Recommended Circuit breaker,
Curve 1 or fuse, slow blow type
Efficiency
Output Specifications
Output voltage
Output voltage adj. range
Output current
Output power max.
Regulation – Input variation
– Load variation (10–100 %)
Ripple and Noise (20MHz Bandwidth)
Electronic short circuit protection
Output overvoltage protection
Overload protection
Overtemperature protection
Status indicator
Power OK signal – trigger threshold:
– active output signal: (reference to –Vout)
– relay output
General Specifications
Operating temperature range
Cooling
Mounting
Storage temperature
Humidity (non condensing)
Pollution degree
Temperature coefficient
Reliability, calculated MTBF @ 25°C acc. to
IEC 61709
Remote On/Off
(See LIT0917 - Installation Instructions)
Isolation
Environment – Vibration acc. IEC 60068-2-6
– Shock acc. IEC 60068-2-27
Dimension (W x D x H)
Clearances – Above /Below
– Sides
Weight
Approvals
Part No.
1105430000
Type
CP T SNT 140W 12V 12A
Part No.
1105440000
Type
CP T SNT 90W 24V 3.8A
Part No.
1105790000
115VAC/230VAC autoselect
85-132/187-264 VAC autoselect (output current derating below 100VAC)
47Hz - 63Hz
EN 61000-3-2, Class A (for limited output power)
20ms min. 115/230 VAC
<12A @ 115VAC; <20A @ 230VAC
6A
115VAC/230VAC autoselect
85-132/187-264 VAC autoselect (output current derating below 100VAC)
47Hz - 63Hz
EN 61000-3-2, Class A (for limited output power)
20ms min. 115/230 VAC
<13A @ 115VAC; <25A @ 230VAC
6A
115VAC/230VAC autoselect
85-132/187-264 VAC autoselect (output current derating below 100VAC)
47Hz - 63Hz
EN 61000-3-2, Class A (for limited output power)
20ms min. 115/230 VAC
<12A @ 115VAC; <20A @ 230VAC
6A
87% typ.
87% typ.
87% typ.
12 VDC
12-14 VDC
6.5A
70W
0.5 % max.
0.5 % max.
100 mV pk-pk typ. (200 mV pk-pk max. at Imax)
Current limitation at Imax., constant current,
automatic recovery
20V
electronic overload protection
Switch off at overtemperature, automatic restart
Dual color LED (green: DC ok; red: DC off)
9–11 V
11.0 V ±1.0 V (20 mA max.)
rated: 30 VDC/1.0 A
12 VDC
12-14 VDC
13.0A
140W
0.5 % max.
0.5 % max.
100 mV pk-pk typ. (200 mV pk-pk max. at Imax)
Current limitation at Imax., constant current,
automatic recovery
20V
electronic overload protection
Switch off at overtemperature, automatic restart
Dual color LED (green: DC ok; red: DC off)
9–11 V
11.0 V ±1.0 V (20 mA max.)
rated: 30 VDC/1.0 A
24 VDC
24-28 VDC
3.75A
90W
0.5 % max.
0.5 % max.
100 mV pk-pk typ. (200 mV pk-pk max. at Imax)
Current limitation at Imax., constant current,
automatic recovery
35V
electronic overload protection
Switch off at overtemperature, automatic restart
Dual color LED (green: DC ok; red: DC off)
18-22 V
22.0 V ±2.0 V (10 mA max.)
rated: 30 VDC/1.0 A
–25 °C to +70 °C max. (–13 °F to +158°F)
convection cooling, no internal fan
TS35 DIN-rail (Horizontal) to allow for cooling
–25 °C to +85 °C (– 13°F to +185°F)
95 % rel. H max.
2
0.02 %/K
>1.8 Million hours, max. load
–25 °C to +70 °C max. (–13 °F to +158°F)
convection cooling, no internal fan
TS35 DIN-rail (Horizontal) to allow for cooling
–25 °C to +85 °C (– 13°F to +185°F)
95 % rel. H max.
2
0.02 %/K
>1.2 Million hours, max. load
–25 °C to +70 °C max. (–13 °F to +158°F)
convection cooling, no internal fan
TS35 DIN-rail (Horizontal) to allow for cooling
–25 °C to +85 °C (– 13°F to +185°F)
95 % rel. H max.
2
0.02 %/K
>1.8 Million hours, max. load
by ext. contact.
DC on: -S contact open
DC off: -S connected via 1Kohm to -Vout
according to IEC/EN 60950-1, UL 60950-1,
UL 508
3 axis, sine sweep, 10–55 Hz, 1 g, 1 oct/min
3 axis, 15 g half sine, 11 ms
35 x 110 x 110 mm
80 mm (3.15 in)
10 mm (0.39 in)
0.5kg
by ext. contact.
DC on: -S contact open
DC off: -S connected via 1Kohm to -Vout
according to IEC/EN 60950-1, UL 60950-1,
UL 508
3 axis, sine sweep, 10–55 Hz, 1 g, 1 oct/min
3 axis, 15 g half sine, 11 ms
54 x 110 x 110 mm
80 mm (3.15 in)
10 mm (0.39 in)
0.7kg
by ext. contact.
DC on: -S contact open
DC off: -S connected via 1Kohm to -Vout
according to IEC/EN 60950-1, UL 60950-1,
UL 508
3 axis, sine sweep, 10–55 Hz, 1 g, 1 oct/min
3 axis, 15 g half sine, 11 ms
35 x 110 x 110 mm
80 mm (3.15 in)
10 mm (0.39 in)
0.5kg
UL file E236157 cULus Listed to UL508, CSA
C22.2 No. 14
UL file E255651 cRUus to ANSI/UL60950,
CSA60950
CSA file 246286 CSA to C22.2 No. 107.1
CSA file 246286 cCSAus to CSA60950,
ANSI/UL60950
CSA file 246286 cCSAus C1D2 to C22.2 No.
213 UL1604, Group A, B, C, D
CSA file 246286 cCSAus C1Z2 to CSA60079-15
& ANSI/ISA 12.012.01, Ex nC IIC T4U, Aex nC
IIC T4U
IEC file SI-1729 B3, CE marked
LCIE file 10, ATEX 1015 U EN60079-0,
EN60079-15 (Ex nAC IIC T4 or T5 with derating)
II 3G Ex nA nC IIC t4 Gc
UL file E236157 cULus Listed to UL508, CSA
C22.2 No. 14
UL file E255651 cRUus to ANSI/UL60950,
CSA60950
CSA file 246286 CSA to C22.2 No. 107.1
CSA file 246286 cCSAus to CSA60950,
ANSI/UL60950
CSA file 246286 cCSAus C1D2 to C22.2 No.
213 UL1604, Group A, B, C, D
CSA file 246286 cCSAus C1Z2 to CSA60079-15
& ANSI/ISA 12.012.01, Ex nC IIC T4U, Aex nC
IIC T4U
IEC file SI-1729 B3, CE marked
LCIE file 10, ATEX 1015 U EN60079-0,
EN60079-15 (Ex nAC IIC T4 or T5 with derating)
II 3G Ex nA nC IIC t4 Gc
UL file E236157 cULus Listed to UL508, CSA
C22.2 No. 14
UL file E255651 cRUus to ANSI/UL60950,
CSA60950
CSA file 246286 CSA to C22.2 No. 107.1
CSA file 246286 cCSAus to CSA60950,
ANSI/UL60950
CSA file 246286 cCSAus C1D2 to C22.2 No.
213 UL1604, Group A, B, C, D
CSA file 246286 cCSAus C1Z2 to CSA60079-15
& ANSI/ISA 12.012.01, Ex nC IIC T4U, Aex nC
IIC T4U
IEC file SI-1729 B3, CE marked
LCIE file 10, ATEX 1015 U EN60079-0,
EN60079-15 (Ex nAC IIC T4 or T5 with derating)
II 3G Ex nA nC IIC t4 Gc
28
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
NEW
PRO-H Series—Single Phase Input Supplies
CP T SNT 180W 24V 7.5A
L (+)
N(-
CP T SNT 600W 24V 25A
+
AC
PE
CP T SNT 360W 24V 15A
DC
-
Ordering Data
Type
CP T SNT 180W 24V 7.5A
Technical Data
Input Specifications
Input voltage
Input voltage range
Input voltage frequency
Harmonic limits
Hold up time
Inrush current
Recommended Circuit breaker,
Curve 1 or fuse, slow blow type
Efficiency
Output Specifications
Output voltage
Output voltage adj. range
Output current
Output power max.
Regulation – Input variation
– Load variation (10–100 %)
Ripple and Noise (20MHz Bandwidth)
Electronic short circuit protection
Output overvoltage protection
Overload protection
Overtemperature protection
Status indicator
Power OK signal – trigger threshold:
– active output signal: (reference to –Vout)
– relay output
General Specifications
Operating temperature range
Cooling
Mounting
Storage temperature
Humidity (non condensing)
Pollution degree
Temperature coefficient
Reliability, calculated MTBF @ 25°C acc.
to IEC 61709
Remote On/Off
(See LIT0917 - Installation Instructions)
Isolation
Environment – Vibration acc. IEC 60068-2-6
– Shock acc. IEC 60068-2-27
Dimension (W x D x H)
Clearances – Above /Below
– Sides
Weight
Approvals
Part No.
1105810000
Type
CP T SNT 360W 24V 15A
Part No.
1105820000
Type
CP T SNT 600W 24V 25A
Part No.
1105840000
115VAC/230VAC autoselect
85-132/187-264 VAC autoselect (output current derating below 100VAC)
47Hz - 63Hz
EN 61000-3-2, Class A (for limited output power)
20ms min. 115/230 VAC
<13A @ 115VAC; <25A @ 230VAC
6A
115VAC/230VAC autoselect
85-132/187-264 VAC autoselect (output current derating below 100VAC)
47Hz - 63Hz
EN 61000-3-2, Class A (for limited output power)
20ms min. 115/230 VAC
<16A @ 115VAC; <25A @ 230VAC
10A
115VAC/230VAC autoselect
85-132/187-264 VAC autoselect (output current derating below 100VAC)
47Hz - 63Hz
EN 61000-3-2, Class A (for limited output power)
20ms min. 115/230 VAC
<25A @ 115VAC; <30A @ 230VAC
15A
87% typ.
87% typ.
87% typ.
24 VDC
24-28 VDC
7.5A
180W
0.5 % max.
0.5 % max.
100 mV pk-pk typ. (200 mV pk-pk max. at Imax)
Current limitation at Imax., constant current,
automatic recovery
35V
electronic overload protection
Switch off at overtemperature, automatic restart
Dual color LED (green: DC ok; red: DC off)
18-22 V
22.0 V ±2.0 V (20 mA max.)
rated: 30 VDC/1.0 A
24 VDC
24-28 VDC
15A
360W
0.5 % max.
0.5 % max.
100 mV pk-pk typ. (200 mV pk-pk max. at Imax)
Current limitation at Imax., constant current,
automatic recovery
35V
electronic overload protection
Switch off at overtemperature, automatic restart
Dual color LED (green: DC ok; red: DC off)
18-22 V
22.0 V ±2.0 V (20 mA max.)
rated: 30 VDC/1.0 A
24 VDC
24-28 VDC
25A
600W
0.5 % max.
0.5 % max.
100 mV pk-pk typ. (200 mV pk-pk max. at Imax)
Current limitation at Imax., constant current,
automatic recovery
35V
electronic overload protection
Switch off at overtemperature, automatic restart
Dual color LED (green: DC ok; red: DC off)
18-22 V
22.0 V ±2.0 V (20 mA max.)
rated: 30 VDC/1.0 A
–25 °C to +70 °C max. (–13 °F to +158°F)
convection cooling, no internal fan
TS35 DIN-rail (Horizontal) to allow for cooling
–25 °C to +85 °C (– 13°F to +185°F)
95 % rel. H max.
2
0.02 %/K
>0.9 Million hours, max. load
–25 °C to +70 °C max. (–13 °F to +158°F)
convection cooling, no internal fan
TS35 DIN-rail (Horizontal) to allow for cooling
–25 °C to +85 °C (– 13°F to +185°F)
95 % rel. H max.
2
0.02 %/K
>0.9 Million hours, max. load
–25 °C to +70 °C max. (–13 °F to +158°F)
convection cooling, no internal fan
TS35 DIN-rail (Horizontal) to allow for cooling
–25 °C to +85 °C (– 13°F to +185°F)
95 % rel. H max.
2
0.02 %/K
>0.9 Million hours, max. load
by ext. contact.
DC on: -S contact open
DC off: -S connected via 1Kohm to -Vout
according to IEC/EN 60950-1, UL 60950-1,
UL 508
3 axis, sine sweep, 10–55 Hz, 1 g, 1 oct/min
3 axis, 15 g half sine, 11 ms
54 x 110 x 110 mm
80 mm (3.15 in)
10 mm (0.39 in)
0.7kg
by ext. contact.
DC on: -S contact open
DC off: -S connected via 1Kohm to -Vout
according to IEC/EN 60950-1, UL 60950-1,
UL 508
3 axis, sine sweep, 10–55 Hz, 1 g, 1 oct/min
3 axis, 15 g half sine, 11 ms
80 x 125 x 125 mm
80 mm (3.15 in)
10 mm (0.39 in)
1.1kg
by ext. contact.
DC on: -S contact open
DC off: -S connected via 1Kohm to -Vout
according to IEC/EN 60950-1, UL 60950-1,
UL 508
3 axis, sine sweep, 10–55 Hz, 1 g, 1 oct/min
3 axis, 15 g half sine, 11 ms
165 x 125 x 125 mm
80 mm (3.15 in)
10 mm (0.39 in)
2.8kg
UL file E236157 cULus Listed to UL508, CSA
C22.2 No. 14
UL file E255651 cRUus to ANSI/UL60950,
CSA60950
CSA file 246286 CSA to C22.2 No. 107.1
CSA file 246286 cCSAus to CSA60950,
ANSI/UL60950
CSA file 246286 cCSAus C1D2 to C22.2 No.
213 UL1604, Group A, B, C, D
CSA file 246286 cCSAus C1Z2 to CSA60079-15
& ANSI/ISA 12.012.01, Ex nC IIC T4U, Aex nC
IIC T4U
IEC file SI-1729 B3, CE marked
LCIE file 10, ATEX 1015 U EN60079-0,
EN60079-15 (Ex nAC IIC T4 or T5 with derating)
II 3G Ex nA nC IIC t4 Gc
UL file E236157 cULus Listed to UL508, CSA
C22.2 No. 14
UL file E255651 cRUus to ANSI/UL60950,
CSA60950
CSA file 246286 CSA to C22.2 No. 107.1
CSA file 246286 cCSAus to CSA60950,
ANSI/UL60950
CSA file 246286 cCSAus C1D2 to C22.2 No.
213 UL1604, Group A, B, C, D
CSA file 246286 cCSAus C1Z2 to CSA60079-15
& ANSI/ISA 12.012.01, Ex nC IIC T4U, Aex nC
IIC T4U
IEC file SI-1729 B3, CE marked
LCIE file 10, ATEX 1015 U EN60079-0,
EN60079-15 (Ex nAC IIC T4 or T5 with derating)
II 3G Ex nA nC IIC t4 Gc
UL file E236157 cULus Listed to UL508, CSA
C22.2 No. 14
UL file E255651 cRUus to ANSI/UL60950,
CSA60950
CSA file 246286 CSA to C22.2 No. 107.1
CSA file 246286 cCSAus to CSA60950,
ANSI/UL60950
CSA file 246286 cCSAus C1D2 to C22.2 No.
213 UL1604, Group A, B, C, D
CSA file 246286 cCSAus C1Z2 to CSA60079-15
& ANSI/ISA 12.012.01, Ex nC IIC T4U, Aex nC
IIC T4U
IEC file SI-1729 B3, CE marked
LCIE file 10, ATEX 1015 U EN60079-0,
EN60079-15 (Ex nAC IIC T4 or T5 with derating)
II 3G Ex nA nC IIC t4 Gc
29
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
NEW
PRO-H Series—Single Phase Input Supplies
CP T SNT 180W 48V 4A
L (+)
N(-
CP T SNT 600W 48V 12.5A
+
AC
PE
CP T SNT 360W 48V 7.5A
DC
-
Ordering Data
Type
CP T SNT 180W 48V 4A
Technical Data
Input Specifications
Input voltage
Input voltage range
Input voltage frequency
Harmonic limits
Hold up time
Inrush current
Recommended Circuit breaker,
Curve 1 or fuse, slow blow type
Efficiency
Output Specifications
Output voltage
Output voltage adj. range
Output current
Output power max.
Regulation – Input variation
– Load variation (10–100 %)
Ripple and Noise (20MHz Bandwidth)
Electronic short circuit protection
Output overvoltage protection
Overload protection
Overtemperature protection
Status indicator
Power OK signal – trigger threshold:
– active output signal: (reference to –Vout)
– relay output
General Specifications
Operating temperature range
Cooling
Mounting
Storage temperature
Humidity (non condensing)
Pollution degree
Temperature coefficient
Reliability, calculated MTBF @ 25°C acc.
to IEC 61709
Remote On/Off
(See LIT0917 - Installation Instructions)
Isolation
Environment – Vibration acc. IEC 60068-2-6
– Shock acc. IEC 60068-2-27
Dimension (W x D x H)
Clearances – Above /Below
– Sides
Weight
Approvals
Part No.
1105850000
Type
CP T SNT 360W 48V 7.5A
Part No.
1105860000
Type
CP T SNT 600W 48V 12.5A
Part No.
1105870000
115VAC/230VAC autoselect
85-132/187-264 VAC autoselect (output current derating below 100VAC)
47Hz - 63Hz
EN 61000-3-2, Class A (for limited output power)
20ms min. 115/230 VAC
<13A @ 115VAC; <25A @ 230VAC
6A
115VAC/230VAC autoselect
85-132/187-264 VAC autoselect (output current derating below 100VAC)
47Hz - 63Hz
EN 61000-3-2, Class A (for limited output power)
20ms min. 115/230 VAC
<16A @ 115VAC; <25A @ 230VAC
10A
115VAC/230VAC autoselect
85-132/187-264 VAC autoselect (output current derating below 100VAC)
47Hz - 63Hz
EN 61000-3-2, Class A (for limited output power)
20ms min. 115/230 VAC
<25A @ 115VAC; <30A @ 230VAC
15A
87% typ.
87% typ.
87% typ.
48 VDC
48-56 VDC
4.0A
180W
0.5 % max.
0.5 % max.
100 mV pk-pk typ. (200 mV pk-pk max. at Imax)
Current limitation at Imax., constant current,
automatic recovery
60V
electronic overload protection
Switch off at overtemperature, automatic restart
Dual color LED (green: DC ok; red: DC off)
36-46 V
44.0 V ±4.0 V (15 mA max.)
rated: 48 VDC/0.5 A
48 VDC
48-56 VDC
7.5A
360W
0.5 % max.
0.5 % max.
100 mV pk-pk typ. (200 mV pk-pk max. at Imax)
Current limitation at Imax., constant current,
automatic recovery
60V
electronic overload protection
Switch off at overtemperature, automatic restart
Dual color LED (green: DC ok; red: DC off)
36-46 V
44.0 V ±4.0 V (15 mA max.)
rated: 48 VDC/0.5 A
48 VDC
48-56 VDC
12.5A
600W
0.5 % max.
0.5 % max.
100 mV pk-pk typ. (200 mV pk-pk max. at Imax)
Current limitation at Imax., constant current,
automatic recovery
60V
electronic overload protection
Switch off at overtemperature, automatic restart
Dual color LED (green: DC ok; red: DC off)
36-46 V
44.0 V ±4.0 V (15 mA max.)
rated: 48 VDC/0.5 A
–25 °C to +70 °C max. (–13 °F to +158°F)
convection cooling, no internal fan
TS35 DIN-rail (Horizontal) to allow for cooling
–25 °C to +85 °C (– 13°F to +185°F)
95 % rel. H max.
2
0.02 %/K
>0.9 Million hours, max. load
–25 °C to +70 °C max. (–13 °F to +158°F)
convection cooling, no internal fan
TS35 DIN-rail (Horizontal) to allow for cooling
–25 °C to +85 °C (– 13°F to +185°F)
95 % rel. H max.
2
0.02 %/K
>0.9 Million hours, max. load
–25 °C to +70 °C max. (–13 °F to +158°F)
convection cooling, no internal fan
TS35 DIN-rail (Horizontal) to allow for cooling
–25 °C to +85 °C (– 13°F to +185°F)
95 % rel. H max.
2
0.02 %/K
>0.9 Million hours, max. load
by ext. contact.
DC on: -S contact open
DC off: -S connected via 1Kohm to -Vout
according to IEC/EN 60950-1, UL 60950-1,
UL 508
3 axis, sine sweep, 10–55 Hz, 1 g, 1 oct/min
3 axis, 15 g half sine, 11 ms
54 x 110 x 110 mm
80 mm (3.15 in)
10 mm (0.39 in)
0.7kg
by ext. contact.
DC on: -S contact open
DC off: -S connected via 1Kohm to -Vout
according to IEC/EN 60950-1, UL 60950-1,
UL 508
3 axis, sine sweep, 10–55 Hz, 1 g, 1 oct/min
3 axis, 15 g half sine, 11 ms
80 x 125 x 125 mm
80 mm (3.15 in)
10 mm (0.39 in)
1.1kg
by ext. contact.
DC on: -S contact open
DC off: -S connected via 1Kohm to -Vout
according to IEC/EN 60950-1, UL 60950-1,
UL 508
3 axis, sine sweep, 10–55 Hz, 1 g, 1 oct/min
3 axis, 15 g half sine, 11 ms
165 x 125 x 125 mm
80 mm (3.15 in)
10 mm (0.39 in)
2.8kg
UL file E236157 cULus Listed to UL508, CSA
C22.2 No. 14
UL file E255651 cRUus to ANSI/UL60950,
CSA60950
CSA file 246286 CSA to C22.2 No. 107.1
CSA file 246286 cCSAus to CSA60950,
ANSI/UL60950
CSA file 246286 cCSAus C1D2 to C22.2 No.
213 UL1604, Group A, B, C, D
CSA file 246286 cCSAus C1Z2 to CSA60079-15
& ANSI/ISA 12.012.01, Ex nC IIC T4U, Aex nC
IIC T4U
IEC file SI-1729 B3, CE marked
LCIE file 10, ATEX 1015 U EN60079-0,
EN60079-15 (Ex nAC IIC T4 or T5 with derating)
II 3G Ex nA nC IIC t4 Gc
UL file E236157 cULus Listed to UL508, CSA
C22.2 No. 14
UL file E255651 cRUus to ANSI/UL60950,
CSA60950
CSA file 246286 CSA to C22.2 No. 107.1
CSA file 246286 cCSAus to CSA60950,
ANSI/UL60950
CSA file 246286 cCSAus C1D2 to C22.2 No.
213 UL1604, Group A, B, C, D
CSA file 246286 cCSAus C1Z2 to CSA60079-15
& ANSI/ISA 12.012.01, Ex nC IIC T4U, Aex nC
IIC T4U
IEC file SI-1729 B3, CE marked
LCIE file 10, ATEX 1015 U EN60079-0,
EN60079-15 (Ex nAC IIC T4 or T5 with derating)
II 3G Ex nA nC IIC t4 Gc
UL file E236157 cULus Listed to UL508, CSA
C22.2 No. 14
UL file E255651 cRUus to ANSI/UL60950,
CSA60950
CSA file 246286 CSA to C22.2 No. 107.1
CSA file 246286 cCSAus to CSA60950,
ANSI/UL60950
CSA file 246286 cCSAus C1D2 to C22.2 No.
213 UL1604, Group A, B, C, D
CSA file 246286 cCSAus C1Z2 to CSA60079-15
& ANSI/ISA 12.012.01, Ex nC IIC T4U, Aex nC
IIC T4U
IEC file SI-1729 B3, CE marked
LCIE file 10, ATEX 1015 U EN60079-0,
EN60079-15 (Ex nAC IIC T4 or T5 with derating)
II 3G Ex nA nC IIC t4 Gc
30
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
NEW
PRO-H Series—Diode Modules for Redundancy
Redundancy Modules
CP T RM 10
Redundancy Module
With a redundancy module
and two PRO-H Series
power supplies (of same
type) you can configure a
highly reliable, truly redundant power system without
any additional components.
This module enforces the
equivalent sharing of the
output current by each
power supply. The system
is fully redundant and
provides output power even
if one power supply has
completely failed e.g. by
short circuit on the output.
In the event that either
power supply fails or is
disconnected, the second
unit will automatically supply
the full current to the load.
The redundancy of the
system is monitored and if
lost, indicated by an alarm
output. The inputs are hot
swappable and can be
loaded up to 15A each.
CP T RM 20
Redundancy Module
Technical Data
Input Specifications
Input
Input current
Output Specifications
Output voltage
Output voltage adj. range
Output power max.
Output current
General Data
Status indicator
Operating temperature
Redundancy OK signal (Alarm)
MTBF in acc. To IEC 61709
Alarm relay contact
Environment - Vibration
- Shock
Dimension (W x D x H)
Weight
Remote link cable (0.5m)
Remote On/Off
2 x 24 VDC
15A
2 x Control Input
25A
24 VDC
24-27 VDC
360 W
15A @ 24VDC, @ 40°C
24 VDC
24-27 VDC
600 W
25A @ 24VDC, @ 40°C
LED
– 25 °C to 70 °C max. (–13 °F...+158 °F)
derating above 40 °C (104 °F): 1.5 %/K
trigger threshold at 18...22VDC,
contact open if both inputs failed
>350,000 hours, max. load
30VDC/1A
3 axis, sine sweep, 10…55Hz, 1g, 1oct/min.
3 axis, 15g half sine, 11ms
35 x 110 x 110 mm
0.5kg
2 cables included
by ext. contact: contact open = On,
contact closed = Off
LED
– 25 °C to 70 °C max. (–13 °F...+158 °F)
derating above 40 °C (104 °F): 1.5 %/K
trigger threshold at 18...22VDC,
contact open if both inputs failed
>350,000 hours, max. load
3 axis, sine sweep, 10…55Hz, 1g, 1oct/min.
3 axis, 15g half sine, 11ms
54 x 110 x 110 mm
0.7kg
2 cables included
by ext. contact: contact open = On,
contact closed = Off
II 3G Ex nA nC IIC t4 Gc
Approvals
II 3G Ex nA nC IIC t4 Gc
Ordering Data
Type
CP T RM 10
Function Diagram
Part No.
1105880000
+
TSP
J1.2
J1.1
J2
J2.3
J2.4
+
J2.1
J2.2
_
Bottom view
Output
Load
Output
Remote
Link 1
1
2
1
2
Volt adjust
DC IN 2_
J1.4
Power
Supplies
Remote
Link 2
J4
J3
J1.3
J4.1
TSP
Top view
1 2 3 4
J3.1
J3.2
+
Part No.
1105890000
Connector Positions
Front view
DC IN 1_
Type
CP T RM 20
J5
REM Controller
J4.2
1
DC IN 1 DC IN 2
J5.1
Alarm
Redundancy
ok
J5.2
J5.3
2
3
4
J5.4
J1
Remote On/Off
1 2 3 4
J1
For detailed installation instructions, please
visit www.weidmuller.com/power_supplies
and download LIT0917
Pin
Pin
Pin
Pin
1
2
3
4
Input 1
Input 1
Input 2
Input 2
J2
-Vin
+Vin
-Vin
+Vin
GND (-)
GND (-)
Vout (+)
Vout (+)
J3
Voltage Control 1
For Input 1
S+
S-
J4
Voltage Control 2
For Input 2
S+
S-
J5
DC-OK Signal
DC-OK Relay Contact
Remote ON/OFF
Remote ON/OFF
31
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
connectPower—Single Phase Input Supplies
CP SNT 55W
CP SNT 160W
Approvals:
r
®
LISTED
%
Diagram/Schematic Circuit Diagram
Ordering Data
Type
Output voltage/maximum current
Technical Data
Input voltage
Minimum
Typical
Maximum
at 115 VAC
at 230 VAC
at 125 VDC
at 250 VDC
CP SNT 55W
24 VDC-28 VDC / 2.3 A
48 VDC / 1.04 A
Part No.
Type
Part No.
9927480024
CP SNT 160W
24 VDC-28 VDC / 6.5 A
9925340024
9927480048
5 VDC / 10 A
9925340005
12 VDC - 15 VDC / 3 A
9927480012
12 VDC / 10 A
9925340012
5 VDC / 3 A
9927480005
48 VDC / 3.25 A
9925340048
85 VAC, 120 VDC
115-230 VAC ± 10%, 50/60 Hz
85 VAC / 195 VAC
115 VAC / 230 VAC ± 10%, (selectable) 50/60Hz
265 VAC, 300 VDC
1.10 A RMS ± 20%
0.55 A RMS ± 20%
590 mA ± 20%
315 mA ± 20%
138 VAC / 250 VAC
2.9 A RMS ± 20%
1.45 A RMS ± 20%
2 A slow fuse (internal, not user serviceable)
Thermistor
Varistor
100 kHz PWM
80%
0.1% RMS Vp-p
1.0%
6.3 A slow fuse (internal, not user serviceable)
Thermistor
Varistor
65 kHz PWM
85%
0.2% RMS Vp-p
2.0%
Overload protection
0.8%
Overcurrent shutdown with automatic restart plus thermal
shutdown/short circuit
0.5%
Overcurrent shutdown with automatic restart plus thermal
shutdown/short circuit
Output surge capability
Maximum capacitance at output
Parallel connection for load sharing
10,000 μF
13 A / 1 sec
6000 μF
up to 3 devices (passive current division)
30 ms
30 ms
180 ms
-40°C…+85°C (-40°F…+185°F)
-20°C…+50°C (-4°F…+122°F) full rated load
Derating: 24 V-1.5 A at 60°C (140°F)
20…85% RH non-condensing
20…90% RH
3 kV RMS
3 kV RMS
1.5 kV RMS
30 ms
-40°C…+85°C (-40°F…+185°F)
-10°C…+50°C (40°F…+122°F) max. full rated load
Derating: 24 V-5.2 A at 60°C (140°F)
20…85% RH non-condensing
20…90% RH
3 kV RMS
3 kV RMS
1.5 kV RMS
500 V RMS
0.1…4.0 mm2 (26…12 AWG)
98 x 57 x 131 mm (3.86 x 2.24 x 5.16 in.)
478 g (1.05 lbs.)
500 V RMS
0.1…4.0 mm2 (26…12 AWG)
127 x 57 x 175 mm (5.00 x 2.24 x 6.9 in.)
880 g (1.94 lbs.)
Horizontal on mounting rail TS35, Chassis
20 mm left and right
30 mm above and below if next to non-heat producing (lowpower) module
60 mm above and below if next to high heat producing module,
(i.e. another power supply)
Horizontal on mounting rail TS35, Chassis
20 mm left and right
30 mm above and below if next to non-heat producing (lowpower) module
60 mm above and below if next to high heat producing module,
(i.e. another power supply)
Changeover contact, 30 VDC / 125 VAC @ 1 A max.
Passive Power Factor Correction
CSA, UL 508 Listed, CE
CSA Class 1 Div. 2 and Zone 2 for 9927480012 and 9927480024
UL 1310 (Class 2) for 9927480024
Part No.
7920560000
CSA, UL 508 Listed, CE
CSA Class 1 Div. 2 and Zone 2 for 9925340024 and 9925340012
Input current
(Average values for reference only)
Input protection
Switching frequency
Efficiency at maximum load
Maximum ripple
Regulation
Fuse
Inrush Current
Overvoltage
load (10-100% load)
at Input voltage
Hold time
(Maximum output current following input loss)
Temperature
Humidity
Galvanic isolation
at 115 VAC
at 230 VAC
Storage
Operating
Operating temperature
Storage temperature
Input-output
Input/output to mounting rail
Input to ground
Output to ground
Wire size
Dimensions (L x W x H)
Weight
Mounting position
Clearance
Fault relay
Approvals/Certifications
Accessories
Chassis Mounting Kit
Side mount Bracket—DIN rail
Part No.
7920560000
7940000542
32
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
connectPower—Single Phase Input Supplies
CP SNT 300W
Approvals:
r
®
LISTED
%
Diagram/Schematic Circuit Diagram
Type
Ordering Data
CP SNT 300W
Technical Data
Input voltage
Minimal
Typical
Input current at 300 W
Topology
Input protection
Switching frequency
Efficiency
Output ripple
Regulation
265 VAC, 200 VDC
3.3 A ± 10%
at 230 VAC
at 100 VDC
1.65 A ± 10%
3.7 A ± 10%
at 200 VDC
1.85 A ± 10%
0.99 (under all load conditions)
Sinusoidal (active power factor corrected)
Fuse
Inrush current
Overvoltage
at max.load
Load (10-100%)
Line (86-265 VAC RMS)
Protection
86 VAC, 100 VDC
115-230 VAC ± 10% 50/60 Hz
Maximum
at 115 VAC
Input power factor
Input current
Overvoltage
Undervoltage
Overload
Output surge capability
Thermal
Adjustable output voltage
Rated output current
Part No.
9916250024
Boost PFC / forward PWM
5 A slow blow 5x20 mm
Thermistor
Varistor
100 kHz ± 5%
80% typical
at 100 kHz: 2 mVp-p
1%
0.2%
Vout > 30 VDC
Vout < 14 VDC
at Vout = 22 VDC, lout > 13.8 A
18.5 A / 300 mSec
Heat sink temperature > 100°C (212°F)
22 VDC…28 VDC (pot. adj.)
at Vout = 24 VDC, lout > 13.5 A
at Vout = 28 VDC, lout > 11.6 A
at Vout = 22 VDC…13.6 A
at Vout = 24 VDC…12.5 A
at Vout = 28 VDC…10.7 A
LED indicator
Shut down
The 300 W power supply offers
the following additional functions
Current limiting: LED yellow
Fault: LED red
On: LED green
Power supply goes to fault mode overvoltage, undervoltage or over temperature for more than 2 sec. fault relay drops out/short circuit
– universal input voltage with PFC (active power factor corrections)
– analog monitoring function
of the output voltage 0…30 V corresponds to 0…10 V ± 3%
Monitoring output impedance
Load share
Maximum capacitance at output
Hold time
of the output current 0…15 A corresponds to 0…10 V ± 3%
of the internal temperature 0°C…+100°C (+32°F…+212°F) corresponds to 0…10 V ± 3%
– Fault relay, 1 changeover, closed-circuit current principle
10 kM min. or 5 mA max.
Current increase up to 60 A by wiring up to 5 300 W power supplies in parallel (active current division)
10,000 μF
30 ms
30 ms
-40°C…+85°C (-40°F…+185°F)
-20°C…+50°C (-4°F…+122°F)
at 115 VAC
at 230 VAC
Storage
Temperature
Galvanic isolation
Operating
Derating
Input-output
Input/output to mounting rail
Input to ground
Output to ground
Dimensions (L x W x H)
Weight
Mounting position
Clearance
Output current derating of approx. 20% at 60°C (140°F)
3 kV RMS
3 kV RMS
1.5 kV RMS
500 V RMS
104 x 240 x 155 mm (4.10 x 9.45 x 6.10 in.)
1180 g (2.60 lbs.)
Horizontal on mounting rail TS35, chassis
20 mm left and right; 30 mm above and below if next to non-heat producing (low-power) module; 60 mm above and below if next to
high heat producing module, (i.e. another power supply)
Approvals/Certifications
UL 508 Listed, CE, CSA Class 1, Div 2 and Zone 2
Part No.
79205600001)
Accessories
Chassis Mounting Kit
1) Order 2 mounting kits for power supply shown above.
33
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
c o n n e c t P o w e r — T h re e P h a s e I n p u t S u p p l i e s
CP SNT 55W 2.3A
3 Phase Input
CP SNT 160W 6.5A
3 Phase Input
Approvals:
r \ %
Diagram/Schematic Circuit Diagram
Ordering Data
Type
CP SNT 55W 2.3A 3 Phase
24 VDC / 2.3 A
Output voltage/maximum current
Technical Data
Input voltage
Minimum
Typical
Maximum
at 360 VAC
at 230 VAC
Fuse
Input current
(Average values for reference only)
Input protection
Inrush Current
Overvoltage
Switching frequency
Efficiency at maximum load
Maximum ripple
Regulation
Load (10-100% load)
at Input voltage
Fault relay
Output surge
Overload protection
Maximum capacitance at output
Parallel connection for load sharing
Hold time
(Maximum output current following input loss)
Temperature
Humidity
Galvanic isolation
9917790324
at 360 VAC
at 480 VAC
Storage
Operating
Input to ground
Output to ground
Type
CP SNT 160W 6.5A 3 Phase
24 VDC-28 VDC / 6.5 A
Part No.
9925340324
306 VAC
342 VAC
360 - 480 VAC
550 VAC
120 mA / Phase
100 mA / Phase
3 x 1 A slow fuse (internal)
480 VAC
528 VAC
0.36 A / Phase
0.34 A / Phase
3 x 12 A slow fuse (internal)
Thermistor
Varistor
100 kHz
85%
0.1% RMS
1.0%
0.8%
Thermistor
Varistor
100 kHz PWM
83%
0.2% RMS
2%
0.5%
10A / 180 ms typ.
Overcurrent shutdown with automatic restart plus thermal
Changeover contact, 30 VDC / 125 VAC @ 1 A max.
13A / 1 sec.
Overcurrent shutdown with automatic restart plus thermal
shutdown/short circuit
10,000 μF
Operating
Storage
Input-output
Input/output to mounting rail
Wire size
Dimensions (L x W x H)
Weight
Mounting position
Clearance
Part No.
shutdown/short circuit
10,000 μF
up to 3 devices (passive current division)
10 ms
15 ms
-40°C…+85°C (-40°F…+185°F)
-20°C…+50°C (-4°F…+122°F)
120 ms
120 ms
-40°C…+85°C (-40°F…+185°F)
-25°C…+50°C (-13°F…+122°F) full rated load
Derating: 10% at 60°C (140°F)
20…85% RH non-condensing
20…90% RH non-condensing
3 kV RMS
3 kV RMS
20…85% RH non-condensing
20…90% RH
3 kV RMS
3 kV RMS
1.5 kV RMS
500 V RMS
0.1…4.0 mm2 (26…12 AWG)
108 x 60 x 168 mm (4.25 x 2.36 x 6.61 in.)
526 g (1.16 lbs.)
Horizontal on mounting rail TS35, Chassis
20 mm left and right
30 mm above and below if next to non-heat producing (lowpower) module
60 mm above and below if next to high heat producing module,
(i.e. another power supply)
1.5 kV RMS
500 V RMS
0.1…4.0 mm2 (26…12 AWG)
138.2 x 58.4 x 177.8 mm (5.44 x 2.3 x 7 in.)
993 g (2.2 lbs.)
Horizontal on mounting rail TS35, Chassis
20 mm left and right
30 mm above and below if next to non-heat producing (lowpower) module
60 mm above and below if next to high heat producing module,
(i.e. another power supply)
CSA, cULus 508 Listed, CE
cULus 508 Listed, CE
Approvals/Certifications
Accessories
Chassis Mounting Kit
L Bracket Mounting Kit—Panelmount
Side mount Bracket—DIN rail
Part No.
7920560000
7940000543
Part No.
7920560000
7940000543
7940000542
34
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
connectPower—Diode Modules for Redundancy
Ordering Data
CP DM 30 (SP-RS-RED./PARR.30A)
15A per Input Diode Module
RSD-40A
20A per Input or 40A Input per Unit
Diode Module with Status Indication
Type
CP DM 30 with voltage sensing and fault relay
Part No.
9987390000
Type
RSD-40A (20 A per input max.) (2 x 20)
Part No.
7940005219
CP DM 30 without voltage sensing
9987860000
RSD-40A (40 A input per unit max.,
2 units required) (1 x 40)
7940005218
Technical Data
Input
Input voltage
Output
14-24 VDC
24 VDC nominal
Input current
Output voltage
15 A per input max.
24 VDC
20 A per input max. / 40 A (7940005218)
24 VDC
Output current
30A Maximum
40 A Maximum
0°C…+50°C (32°F…+122°F)
(40°C rise (104°F) above ambient at 30 A)
-20°C…+85°C (-4°F…+185°F)
0°C…+40°C (32°F…+104°F) ambient
General Specifications
Temperature
Operating
Storage
Heat dissipation
Efficiency under max. load
Mount onto mounting rail
95%
TS32 or TS35 mm DIN rails
12W @ 40A (7940005218 only)
95%
TS32 or TS35 mm DIN rails
Mounting position
Mounting
Horizontal
Clearance: side 2 4 cm; above/below 2 10 cm
Horizontal
Clearance: side 2 4 cm; above/below 2 10 cm
Weight
Dimensions (L x W x H)
Type of Connection
226.8 g (0.5 lbs.)
70 x 110 x 90 mm (2.75 x 4.33 x 3.5 in.)
Screw
317.5 g (0.7 lbs.)
109.2 x 109.2 x 99 mm (4.3 x 4.3 x 3.9 in.)
Screw
Clamping area input (nominal / min. / max.)
4 / 0.32 / 16 mm2 (12 / 22 / 6 AWG)
1.5 / 0.32 / 16 mm2 (14 / 22 / 6 AWG)
Clamping area output (nominal / min. / max.)
Indication signals
4 / 0.32 / 16 mm2 (12 / 22 / 6 AWG)
None for 998786
Actual voltage for 998739
1.5 / 0.32 / 16 mm2 (14 / 22 / 6 AWG)
“AN.1” = input 1 (2 x 20 A version)
“AN.2” = input 2 (2 x 20 A version)
“AN.1” = “AN.2” = input voltage (1 x 40 A version)
Voltage
Alarm
Fault Relay
Other
Terminations
Voltage
Current
Configuration
Set point
Voltage drop input-output
Fan
Input/output
Alarm contact
“CATH” = output voltage
0-10 VDC = 0°C…+100°C (32°F…+212°F)
15 VDC Max. output (150°C [302°F])
24 VDC under normal operating conditions
0 VDC if heatsink temperature exceeds 90°C (194°F)
None
125 VAC Maximum
6 A Maximum
1 Form C / SPDT
14-24 VDC, ± 5% typ.
0.38 V typ.
None
N/A
N/A
N/A
N/A
0.40 V typ.
Turns on when heatsink temperature exceeds 60°C (140°F)
Proportional control (fan speed increases as heatsink
2.5 mm2 (26…14 AWG)
26…12 AWG
temperature increases–fully on at 80°C [176°F])
13 mm2 (22…6 AWG)
26…14 AWG
UL recognized, a
cULus Listed
Approvals/Certifications
RSD-40A Schematics
7940005218
7940005219
OUT 1
OUT 2
OUT 3
OUT 4
IN 1
IN 2
Alarm
& Fan
Control
OUT 1
OUT 2
OUT 3
OUT 4
IN 1
IN 2
AN.1
AN.1
AN.2
AN.2
CATH
CATH
Deg. C
(0-10 VDC = 0-100°C)
Alarm
(0V = Deg. C > 90°C)
Alarm
& Fan
Control
Deg. C
(0-10 VDC = 0-100°C)
Alarm
(0V = Deg. C > 90°C)
COM (0V)
COM (0V)
35
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
I n t ro d u c t i o n — c o n n e c t P o w e r — D C - D C C o n v e r t e r s
DC to DC converters enable customers
to derive low voltage DC signals from
either 12 VDC or 24 VDC sources. They
are typically connected at the output of
a DC power source and can deliver
DC voltages of 5, 12, 15 or 24 volts.
DC voltage converters (DC to DC
converters) are intended in particular
for the decentralized power supply of
circuits, assemblies and modules.
DC voltage converters are often required
for emergency generators to supply
electrical devices from batteries or other
DC systems.
DC-DC Converters
• 12V and 24V input versions
• Just 57mm (2.24”) wide
• 5V, 12V, 15V and 24V output
variations
• Robust metal housing
• User adjustable output voltage
• Input and output plug-socket
connectors
• CSA Class 1 Div 2 and Zone 2
• UL508 listed
• Output status LED
• DIN rail (TS35) mountable
• Chassis mountable with
optional hardware
The CP-DCDC 50W family is available in
2 input versions and 4 output versions,
making them very versatile.
Typical applications include feeding TTL
level circuits (5 VDC) and providing emergency power to low voltage circuits.
Remote Monitoring
SUN
Antenna
Antenna
Solar Cell
24VDC
I/O Devices
and Sensors
I/O 24VDC
Radio
Transmitter
12V (powered)
• DC-DC converter used to convert solar
array output (24 VDC in this case) that
is used for powering 24 VDC
input/output devices, to 12 VDC used
for power to lower cost radio transmitter. The transmitter panel (remote monitoring system) transmits information to
SCADA system that can monitor the
conditions/physical properties at the
remote site, taking corrective actions,
alarming, or simply providing information on conditions at remote site.
12VDC
+
+ OUTPUT
-
15VDC
3A
-
SCADA System
or Other Type
of Control System
V out Adjust
DC ON
+
-
INPUT
12VDC ±15%
2.37A ±15%
24VDC
36
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
connectPower—DC-DC Converters
CP-DCDC 50W
12 VDC Input
CP-DCDC 50W
24 VDC Input
Approvals:
r v %
Ordering Data
Output voltage/maximum current
Technical Data
Input voltage
Type
CP-DCDC 50W
22 - 24 VDC @ 2 A
15 VDC @ 3 A
12 VDC @ 3 A
5 VDC @ 8 A
Part No.
9919371224
Type
CP-DCDC 50W
22-24 VDC @ 2 A
Part No.
9919372424
9919371215
9919371212
15 VDC @ 3 A
12 VDC @ 3 A
9919372415
9919372412
9919371205
5 VDC @ 8 A
9919372405
12 VDC
10.2 VDC
24 VDC
18 VDC
Typical
Maximum
5 VDC @8A
12 VDC @3A
15 VDC @3A
12 VDC
16 VDC
4.53 A
3.88 A
4.7 A
24 VDC
30 VDC
2.3 A
1.93 A
2.37 A
24 VDC @2A
Fuse
4.96 A
internal (not user serviceable) 2 A
2.49 A
internal (not user servicable) 2 A
Switching frequency
Efficiency at Maximum load
180 kHz PWM
80% (75% 5 VDC @8 A)
330 kHz PWM
80% (75% 5 VDC @8 A)
Maximum ripple
0.2% RMS
0.2% RMS
Overload protection
Maximum capacitance at output
Hold time
5 VDC @8A
12 VDC @3A
15 VDC @3A
Overvoltage switch-off with automatic reset/short circuit
10,000 μF (8000 μF 5 VDC @8 A)
2.5 mS
3.8 mS
3.5 mS
Overvoltage switch-off with automatic reset/short circuit
8000 μF
7.8 mS
10 mS
7 mS
24 VDC @2A
Storage
Operating
3.5 mS
-40°C…+85°C (-40°F…+185°F)
-10°C…+50°C (+14°F…+122°F) full rated load
7 mS
-40°C…+85°C (-40°F…+185°F)
-10°C…+50°C (+14°F…+122°F) full rated load
20…85% RH
20…90% RH non-condensing
500 VAC RMS
4 KV RMS
500 VAC RMS
20…85% RH
20…90% RH non-condensing
500 VAC RMS
4 KV RMS
500 VAC RMS
500 VAC RMS
500 VAC RMS
0.1…4.0 mm2 (26…12 AWG)
98 x 57 x 131 mm (3.86 x 2.24 x 5.16 in.)
454 g (1 lb.)
Horizontal on mounting rail TS35, Chassis w/ optional kit
20 mm left and right
30 mm above and below if next to non-heat producing (lowpower) module
60 mm above and below if next to high heat producing module,
(i.e. another power supply)
0.1…4.0 mm2 (26…12 AWG)
98 x 57 x 131 mm (3.86 x 2.24 x 5.16 in.)
454 g (1 lb.)
Horizontal on mounting rail TS35, Chassis w/ optional kit
20 mm left and right
30 mm above and below if next to non-heat producing (lowpower) module
60 mm above and below if next to high heat producing module,
(i.e. another power supply)
CSA, UL Listed, CE
CSA Class 1 Div. 2 and Zone 2
CSA, UL Listed, CE
CSA Class 1 Div. 2 and Zone 2
Minimum
Input Current for output of:
Input protection
Temperature
Humidity
Operating temperature
Storage temperature
Input to output
Input/output to rail
Input to ground
Galvanic isolation
Output to ground
Wire size
Dimensions (L x W x H)
Weight
Mounting position
Clearance
Approvals/Certifications
Accessories
Part No.
Chassis Mounting Kit
L Bracket Mounting Kit—Panelmount
Part No.
7920560000
7940000543
7920560000
7940000543
37
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
Introduction—connectPower—Battery Back Up Unit for DC Power Management
Weidmuller’s Battery Back Up Unit
(BBU) is designed to be the heart of an
uninterruptible DC power management
system. The connectPower BBU combines with Weidmuller power supplies
and a customer-supplied battery pack to
form a scalable DC power system. This
enables users to put together a system
uniquely tailored to their needs.
Battery Back Up Units:
These full-featured units have all the
diagnostics needed to monitor the status
of the power system. These DC power
management units interface with the DC
power supplies in the control cabinet. In
addition, they monitor the status of the
DC loads and the DC batteries. If the AC
is removed or experiences a voltage sag,
the load is switched seamlessly to the
batteries. When the AC line is restored, the
batteries are recharged and maintained.
• Continuously monitors DC output
voltage of power supply
• DC backup system that actively
manages DC battery banks
• Increases system uptime by providing
DC power to load in the event of an
AC power failure
• If the input fails, the load is switched
seamlessly to batteries
• Extensive monitoring is provided via
LEDs and outputs
With the BBU Power Supply, 2A of
battery charging current is available at
24 VDC, and 3A with the 12 VDC units.
Extensive monitoring is provided via
LEDs. Relay contacts provide battery
status indication and fault indication.
Battery Back Up Unit for DC Power Management
LOADS
Battery Back Up
Power Supply
BATTERY +
Battery
BATTERY EXT. PS +
991628 0024
24VDC BATTERY
BACK-UP UNIT
r
CLASS 1, DIVISION 2
GROUPS A, B, C &D T4A
SEE SIDE PANEL
EXT. PS LOAD +
DC OUTPUT
LOAD +
LOAD -
15A MAX.
LOAD -
CHARGING
FULL CHARGE
BATTERY
OPEN
BATTERY
LOW
BATTERY
REVERSE
FAULT
115-230VAC. 1.0A-0.6A B.B.U. ONLY
I MAX. = 10A (RMS) = B.B.U. + EXT. PS
50/60Hz
+ ENABLE
+ DRAIN
+ DRAIN
RESET
- COM
BAT
STATUS
MAX. 1A
@30VDC
FAULT
RELAY
MAX. 1A
@30VDC
L
IN
g AC
B.B.U.
N
L
AC OUT
g EXT. PS
N
%
®
LISTED
9ZX0
AC INPUT
r
PS AC INPUT
LGN
BBU AC IN
38
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
connectPower—Battery Back Up Unit for DC Power Management
BBU
12 VDC Input
BBU
24 VDC Input
Approvals:
r v %
Ordering Data
Type
BBU 12 VDC
Part No.
9916280012
Type
BBU 24 VDC
Part No.
9916280024
Technical Data
Input voltage
Minimum
Typical
Maximum
Input current
Input protection
Output to Load
85 VAC
115-230 VAC ± 10%
265 VAC
85 VAC
115-230 VAC ± 10%
265 VAC
at 115 VAC
at 230 VAC
0.8 A
0.5 A
1.0 A
0.6 A
Fuse
Input current
2 A slow blow (internal, not user serviceable)
Thermistor 40 A maximum
2 A slow blow (internal, not user serviceable)
Thermistor 40 A maximum
Varistor
12 VDC syst.
15 A maximum
Varistor
24 VDC syst.
15 A maximum
20 A max for 300 mS
30 A max for 100 mS
12-14 VDC
10 A maximum
< 0.5 mS
Limited by internal 4.0 A fuse
16 V
20 A max for 300mS
30 A max for 100mS
24-28 VDC
10 A maximum
< 0.5 mS
Limited by internal 4.0 A fuse
32 V
9.3 V
120°C (248°F) ±10%
18.3 V
120°C (248°F) +10%
Overvoltage
Voltage Nominal
Load Current
Surge Current from no load
Load voltage
AC input current
Switching time from external PS to battery
Protection
Battery Polarity Protection
Battery Overvoltage
Battery Undervoltage
BBU Over Temperature Shutdown
Charger Short Circuit
Continuous
Continuous
Load Short Circuit
Storage
Operating
Storage
Operating
Continuous
-20°C…+85°C (-4°F…+185°F)
-20°C…+50°C (-4°F…+122°F)
20…90%
20…85% non-condensing
Continuous
-20…+85°C (-4°F…+185°F)
-20…+50°C (-4°F…+122°F)
20…90%
20…85% non-condensing
Input to output
Input/output to rail
3 KV
3 KV
3 KV
3 KV
1.5 KV
500 V
0.1…4 mm2 (26…12 AWG)
0.5…1.5 mm2 (28…14 AWG)
1.5 KV
500 V
0.1…4 mm2 (26…12 AWG)
0.5…1.5 mm2 (28…14 AWG)
Dimensions (L x W x H)
127.5 x 72.5 x 161 mm (5.02 x 2.85 x 6.34 in.)
127.5 x 72.5 x 161 mm (5.02 x 2.85 x 6.34 in.)
Weight
950 g (2.09 lbs.)
950 g (2.09 lbs.)
dry contact/open collector
dry contact/open collector
dry contact/open collector
Form C Relay and LED
Form C Relay and LED
3.0 A
Regulates to 13.65 V
LED
dry contact/open collector
dry contact/open collector
dry contact/open collector
Form C Relay and LED
Form C Relay and LED
2.0 A
Regulates to 27.3V
LED
LED
Yellow LED on below 11 V
4 AH
scalable, see example on page 41
Horizontal on mounting rail TS35 (optional direct panel mount)
20 mm left and right
30 mm above and below if next to non-heat producing (lowpower) module
60 mm above and below if next to high heat producing module,
LED
Yellow LED on below 22 V
4 AH
scalable, see example on page 41
Horizontal on mounting rail TS35 (optional direct panel mount)
20 mm left and right
30 mm above and below if next to non-heat producing (lowpower) module
60 mm above and below if next to high heat producing module,
(i.e. another power supply)
plug and socket
(i.e. another power supply)
plug and socket
CSA, UL 508 Listed, CE, CSA Class 1 Div. 2 and Zone 2
Part No.
7920560000
CSA, UL 508 Listed, CE, CSA Class 1 Div. 2 and Zone 2
Part No.
7920560000
Temperature
Humidity
Galvanic Isolation
Wire Size
Control inputs
Status outputs
Battery Charger
Battery Capacity
Mounting position
Clearance
Connections
Approvals/Certifications
Accessories
Chassis Mounting Kit
Input to ground
Output to ground
Power Connections
Control inputs/relay outputs
Enable
Drain
Drain Reset
Battery Status
Fault
Charge Current
Full Charge
Battery Reverse
Battery Open
Battery Low
Minimum
Maximum
39
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
connectPower—Battery Back Up Unit for DC Power Management—Operation
Functional Outline
The BBU is at its basic level a scalable
UPS for 12 VDC or 24 VDC power. It is
the heart or center of the system with
everything wired through it. In this way it
can monitor the status of the AC mains,
the AC to the power supply, the DC out
of the power supply and the battery condition. The BBU does NOT have built-in
batteries. The batteries are sized based
on the current and time demand for the
back-up power.
up current and the length of time that the
current is required. There is no upper limit
to the size of the batteries; we do not
recommend that a battery pack smaller
then 4Ahr be used due to the bulk
charge rates of the BBU (3A for the 12V
version and 2A for the 24V version), as
they may be damaged with a bulk charge
at this level.
The BBU switches the output current
from Power supply to Battery through an
internal Mosfet. This allows the unit to
switch over in milliseconds.
The BBU has two form C relays, one for
Battery status and the other for Fault
monitoring. There are three inputs as
follows: Enable, Drain and Drain Reset.
These I/O are explained in detail below.
The typical system is comprised of the
following: the BBU, the battery pack and
the power supply. The power supply is
sized as per normal requirements (how
much current is needed). The batteries
are sized based on the amount of back-
Under normal conditions the BBU operates
as a battery charger. It trickles the batteries to a minimum voltage (if necessary)
then bulk charges at a rate of 3A for the
12V version and 2A for the 24V version
until the batteries reach 14.75V / 29.5V.
At this point the BBU floats the batteries
to 13.65V / 27.3V.
Digital Inputs
Diagnostic LEDs
Relay Outputs
Enable:
A connection between the “Enable”
and “COM” terminals enables the BBU.
If terminals are open circuit (Disabled),
the BBU functions as a battery charger
only. In the event of AC failure the
batteries are not connected to the load
via the BBU. The BBU is factory preset
as Enabled.
Full Charged LED (green):
On when battery voltage is
14.75/29.5V or greater.
Bat Status relay is energized.
Once fully charged the BBU drops the
charge voltage to 13.65/27.3V (“float”
voltage).
Bat Status:
Battery status, this changes state
based on whether the batteries
are charging or fully charged.
See Diagnostic LEDs (Full Charge,
Battery Low and Full Charge) for
more detailed information.
Battery Low LED (yellow):
On when battery voltage is <11/22 VDC.
Bat Status relay is off.
If the battery voltage drops below
9.7/18.7V the load is switched off.
Fault Relay:
De-energizes under a fault condition.
See Diagnostic LEDs (Fault LED,
Battery Reverse, and Battery Open)
for more detailed information.
Drain:
A temporary short between the “Drain”
and “COM” terminals switches the load
to the batteries until the battery voltage
reaches 11/22V. At this point the AC
power is returned to the power supply
and the BBU starts recharging the batteries. The Drain cycle can also be
reset / terminated by activating the
“Drain Reset” input.
Drain Reset:
A temporary short between the
“Drain Reset” and “COM” terminals disables the Drain cycle to the batteries.
Charging LED (yellow):
On when BBU is charging the batteries.
Off when the “Full Charged” LED is on.
Fault LED (red):
On when AC fails.
On when the external power supply
voltage is <11V/21.5V.
On when the batteries are not connected.
On when the battery voltage is <9.7/18.7V.
Fault relay de-energizes for the above
conditions.
Battery Reverse LED (red):
Batteries connected in reverse.
Fault relay de-energizes and fault LED
turns on.
There is an internal fuse that will open
to prevent damage to BBU or to the
batteries.
Battery Open LED (red):
No batteries connected – takes approx.
60 seconds to detect after turning on
BBU.
Fault LED is on and Fault relay is
de-energized.
40
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
connectPower—Battery Back Up Unit for DC Power Management—Operation
Typical Schematic
• The 15A Critical Load limit is a limit of
the BBU itself and not the power supply.
• This schematic is representative of a
24 VDC system. For a 12 VDC system
use a 12 VDC battery pack, a 12 VDC
power supply and a 12 V BBU, part
number 991628 0012.
• The fuses may be replaced by another
means of circuit protection, i.e. circuit
breakers.
• It is recommended to monitor the
power supply Fault/Status relay/output
if available.
• The power supply shown is for illustration purposes only. The power supply
needs to be chosen based on load
requirements.
Recommendations for Operation
A drain cycle should be run as often as the application permits,
six to twelve times per year is recommended. This allows the
batteries to maintain their capacity, and it also allows you to
validate their condition by monitoring the length of time that it
takes to recharge. By knowing the capacity of the battery, you
can calculate the approximate length of time that it will take to
recharge by monitoring the “Bat Status” relay.
Example
30Ahr battery at 24 VDC
The 24 VDC BBU has a bulk charge current of 2A
The formula to calculate the time to recharge a
dead battery is:
(30Ahr / 2A) x 2 = 30 hrs
The formula to calculate the time to recharge after
a drain cycle is:
((30Ahr / 2A) x 0.56) x 2 = 16.8 hrs
The “x 2” in both formulas is because we overcharge
the batteries so that they are fully charged—otherwise
they only charge to just above 90%.
When running a drain cycle, the system only discharges
the batteries to 22V / 11V. The batteries still have a fair
bit of capacity left.
Please note that these formulas are NOT exact and are
only approximations. This is due to variables such as actual
battery capacity tolerance, temperature, voltage drop in cables,
rate of discharge, etc.
In systems that run 24/7, there is never a good time to run the
drain cycle. In these cases it is recommended to upsize the
batteries as much as possible. It is still recommended to run
drain cycles in these conditions. This is one of the key features
of this product allowing you to validate the condition of the
batteries. Please keep in mind that the batteries are NOT completely drained by running a drain cycle. The drain cycle runs
the batteries to a voltage of 22V / 11V. In the worst case
scenario, if you happen to lose power during a drain cycle,
the drain cycle will reset at a battery voltage of 22V /11V. The
BBU will continue to power the load until the batteries reach
18V / 9V. Then and only then it will shut down power to the
load. Because of this, and assuming that the batteries are bigger than needed, you shouldn’t have a situation that leaves you
without power.
We cannot stress how important it is to choose the batteries
carefully for your application. The BBU is designed to work
with many types of batteries, and works well with sealed
lead acid, Gel cell and automotive / marine batteries. When
selecting batteries keep in mind variables such as temperature
extremes, cycle frequency (frequency of power outages) and
many other environmental conditions. Many battery types can
vent, creating a dangerous condition in a sealed panel. Please
consult the battery manufacturer for recommendations
specific to your application.
The temperature to which batteries are subjected is very
important. Many manufacturers do not recommend recharging
batteries if they are colder then 0°C (32°F) or hotter then 40°C
(104°F). Again, please consult the battery manufacturer for
recommendations.
It is recommended to use at least a 25% hysterisis on the
calculated number of hours. Keep in mind that the battery
capacity will decrease over time, and this is normal. The best
thing to do is to run a test on a known good set of batteries
at room temperature and base the midpoint on the actual
number of hours it takes to recharge after a drain cycle.
41
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
I n t ro d u c t i o n — E l e c t ro n i c C i rc u i t P ro t e c t i o n E S X 1 0 - T
Electronic circuit protection type ESX10-T
is designed to ensure selective disconnection of 24VDC load systems.
24VDC power supplies, which are widely
used in industry today, will shut down
the output in the event of an overload
with the result that one faulty load in the
system can lead to complete disconnection of all loads.
Upon detection of overload or short
circuit in the load circuit, the MOSFET
of the load output will be blocked to
interrupt the current flow. The load
circuit can be re-activated via the
remote electronic reset input, control
input or manually by means of the
ON/OFF button.
Through selective disconnection the
ESX10-T responds much faster to overload or short circuit conditions than
the switch-mode power supply. This is
achieved by active current limitation.
The ESX10-T limits the highest possible
current to 1.3 to 1.8 times the selected
rated current of the circuit protector. Thus
it is possible to switch on capacitive loads
of up to 20,000 μF, but they are disconnected only in the event of an overload
or short circuit.
Features
For optimal alignment with the characteristics of the application the current rating
of the ESX10-T can be selected in fixed
values from 0.5 A...12 A. Failure and
status indication are provided by a
multicolour LED and an integral shortcircuit-proof status output or a relay signal
contact. Remote operation is possible
by means of a remote reset signal or
a remote ON/OFF control signal.
The manual ON/OFF button allows
separate actuation and reset of
individual load circuits.
• Manual ON/OFF button (S1)
• Ease of wiring through busbar LINE+
and 0 V as well as signal bars and
bridges
• Control input IN+ for remote ON/OFF
signal (option)
• UL/CSA Hazardous area approved–
Class 1, Div 2
• Selective load protection, electronic trip
characteristics
• Active current limitation for safe connection of capacitive loads up to 20,000 μF
and on overload/short circuit
• Clear status and failure indication
through LED, status output SF or
Si contact F
• Integral fail-safe element adjusted
to current rating
• Current ratings 0.5 A...12 A
• Width per unit only 12.5 mm
• Reliable overload disconnection with
1.1 x In plus, even with long load lines or
small cable cross sections (see table 3)
• Rail mounting
• Electronic reset input RE (option)
42
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
E l e c t ro n i c C i rc u i t P ro t e c t i o n E S X 10 - T
Approvals
Technical data
Authority
UL2367 (E306740)
UL1604 (E322549)
(class 1, div. 2, group A, B, C, D)
UL508/ cUL 508
CSA file 165971:
CSA C22.2 No: 213 (class I, div. 2)
Groups A, B, C, D, T5
CSA C22.2 No: 142
Class 2
Meets requirements for Class 2 current limitation
(ESX10-T... 0.5 A / 1 A / 2 A / 3 A
Voltage rating
24VDC
24VDC
Current ratings
0.5...12 A
0.5...12 A
24VDC
0.5...12 A
24VDC
0.5...12 A
24VDC
0.5...12 A
(Tambient = 40°C, operating voltage Ub = 24VDC)
Status output SF
Electrical data
Status OUT
OFF condition
Technical data
(Tambient = 40°C, operating voltage Ub = 24VDC)
Operating data
Operating voltage Ub
Current rating In
Closed current I0
Status indication
by means of
Load circuit
Load output
Overload disconnection
Short-circuit current IK
Trip time
for electronic disconnection
Temperature disconnection
Low voltage monitoring
load output
24VDC (18...32 V)
fixed current ratings: 0.5, 1 A, 2 A, 3 A, 4 A,
6 A, 8 A, 10 A, 12 A
ON condition: typically 20...30 mA
depending on signal output
• multicolour LED:
GREEN: unit is ON, power-MOSFET
is switched on
- status output SF ON,
supplies + 24VDC
ORANGE: in the event of overload or
short circuit until electronic
disconnection
RED: - unit electronically disconnected
- load circuit/Power-MOSFET
OFF
OFF: - manually switched off
(S1 = OFF)
or device is dead
- undervoltage (Ub < 8 V)
- after switch-on till the end
of the delay period
• status output SF (option)
• potential-free signal contact F (option)
• ON/OFF/ condition of switch S1
Power-MOSFET switching output
(high side switch)
typically 1.1 x In (1.05...1.35 x In)
active current limitation (see table 1)
see time/current characteristics
typically 3 s at ILoad > 1.1 x In
typically 3 s...100 ms at ILoad > 1.8 x In
(or 1.5 x In/1.3 x In)
internal temperature monitoring with
electronic disconnection
with hysteresis, no reset required
load “OFF” at Ub < 8 V
Starting delay tstart
typically 0.5 sec after every switch-on
and after applying Ub
Disconnection of load circuit
electronic disconnection
Free-wheeling circuit
external free-wheeling diode
recommended with inductive load
Several load outputs must not be connected in parallel
Signal output F
Electrical data
ON condition LED green
OFF condition LED off
Fault condition LED orange
Fault condition LED red
ESX10-TB-101
ESX10-TB-102
Fault
Reset input RE
Electrical data
Reset signal RE
(terminal 22)
Control input IN+
Electrical data
Control signal IN+
(terminal 21)
Switch S1 ON/OFF
ESX10-TB-114/-124/
plus-switching signal output,
connects Ub to terminal 12 of module 17plus
nominal data: 24VDC / max. 0.2 A (short circuit proof)
status output is internally connected to
GND with a 10 kOhm resistor
ESX10-TB-114/-124 (signal status OUT),
at Ub = +24 V
+24 V = S1 is ON, load output connected through
0V = S1 is ON, load output blocked and/or
switch S1 is OFF
red LED lit
0 V level at status output when:
• switch S1 is in ON position, but device is
still in switch-on delay
• switch S1 is OFF, or control signal OFF,
device is switched off
• no operating voltage Ub
ESX10-TB-101/-102
potential-free signal contact
max. 30VDC/0.5 A, min. 10 V/10 mA
voltage Ub applied, switch S1 is in ON position
no overload, no short circuit
• device switched off (switch S1 is in OFF position)
• no voltage Ub applied
overload condition > 1.1 x In up to
electronic disconnection
electronic disconnection upon
overload or short circuit
device switched off with control signal
(switch S1 is in ON position)
single signal, make contact
contact SC/SO-SI open
single signal, break contact
contact SC/SO-SI closed
signal output fault conditions:
• no operating voltage Ub
• ON/OFF switch S1 is in OFF position
• red LED lighted
(electronic disconnection)
ESX10-TB-124
voltage: max. +32VDC
high > 8VDC ≤ 32VDC
low ≤ 3VDC > 0 V
power consumption typically 2.6 mA
(+24VDC)
min. pulse duration typically 10 ms
The electronically blocked ESX10-TB-124
may remotely be reset via an external
momentary switch due to the falling edge of
a +24 V pulse.
A common reset signal can be applied to
several devices simultaneously.
Switched on devices remain unaffected.
ESX10-TB-114
see reset input RE
+24V level (HIGH): device will be switched
on by a remote ON/OFF signal
0 V level (LOW): device will be switched
off by a remote ON/OFF signal
unit can only be switched on with S1 if a
HIGH level is applied to IN+
43
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
E l e c t ro n i c C i rc u i t P ro t e c t i o n E S X 1 0 - T
Technical data
(Tambient = 40°C, operating voltage Ub = 24VDC)
General data
Fail-safe element:
Mounting
Ambient temperature
Storage temperature
Humidity
backup fuse for ESX10-T not required
because of the integral
redundant fail-safe element
LINE+ / LOAD+ / 0V
Terminals
screw terminals
max. cable cross section
flexible with wire end ferrule w/wo plastic sleeve
multi-lead connection
(2 identical cables)
rigid/flexible
flexible with wire end ferrule without plastic sleeve
flexible with TWIN wire end ferrule with plastic sleeve
wire stripping length
tightening torque (EN 60934)
Terminals
aux. contacts
screw terminals
max. cable cross section
flexible with wire end ferrule w/wo plastic sleeve
wire stripping length
tightening torque (EN 60934)
Housing material
moulded
M4
symmetrical rail to EN 50022-35x7.5
0...+50 °C (without condensation, see EN 60204-1)
-20...+70 °C
96 hrs/95 % RH/40 °C to IEC 60068-2-78-Cab
climate class 3K3 to EN 60721
3 g, test to IEC 68-2-6 test Fc
housing: IP20 DIN 40050
terminals: IP20 DIN 40050
emission: EN 61000-6-3
susceptibility: EN 61000-6-2
0.5 kV/2 pollution degree 2
re-inforced insulation in operating area
max. 32VDC (load circuit)
Vibration
Degree of protection
20-6 AWG (0.5 - 10 mm2)
20-11 AWG (0.5 - 4 mm2)
20-13 AWG (0.5 - 2.5 mm2)
20-9 AWG (0.5 - 6 mm2)
10 mm
1.2 Nm
EMC
(EMC directive, CE logo)
Insulation co-ordination
(IEC 60934)
dielectric strength
Insulation resistance
(OFF condition)
Approvals
n/a, only electronic disconnection
UL2367, File E306740,
Solid State Overcurrent Protectors
UL1604 (class I, div. 2, zone 2), UL508, CE logo
CSA C22.2 No. 142 - file 165971, C22.2 No. 213 - file
165971, C1D2 Groups A, B, C, D, Temp Code T5;
Ambient 0°-40°C
12.5 x 80 x 83 mm
approx. 65 g
M3
23-13 AWG (0.25 – 2.5 mm2)
8 mm
0.5 Nm
Dimensions (W x H x D)
Mass
Table 1:
voltage drop, current limitation, max. load current
current rating
In
0.5 A
1A
2A
3A
4A
6A
8A
10 A
12 A
typically voltage drop active current
Uon at In
limitation (typically)
70 mV
1.8 x In
80 mV
1.8 x In
130 mV
1.8 x In
80 mV
1.8 x In
100 mV
1.8 x In
130 mV
1.8 x In
120 mV
1.5 x In
150 mV
1.5 x In
180 mV
1.3 x In
max. load current at 100% ON duty
Tu = 40 °C
Tu = 50 °C
0.5 A
0.5 A
1A
1A
2A
2A
3A
3A
4A
4A
6A
5A
8A
7A
10 A
9A
12 A
10.8 A
Please note:
•
The user should ensure that the cable cross sections of the relevant load
•
Automatic start-up of machinery after shut down must be prevented
circuit are suitable for the current rating of the ESX10-T used.
(Machinery Directive 98/37/EG and EN 60204-1). In the event of a short
circuit or overload the load circuit will be disconnected electronically by
the ESX10-T.
•
Refer to UL/CSA file for proper wiring and installation techniques.
Attention: when mounted side-by-side without convection the ESX10-T should not carry more
than 80% of its rated load with 100% ON duty due to thermal effects.
Table 2: ESX10-T - Ordering Information
Version
Signal input
without
Signal
Input
ESX10-TA-100
x
ESX10-TB-101
x
ESX10-TB-102
x
Control input
ON/OFF Reset
Signal output
Remote
Reset
without
Signal
Output
Status output
Status OUT
Positive 24V
= OK
without
Signal
Output
x
x
x
x
x
x
ESX10-TB-124
x
x
ESX10-TB-127
x
x
ESX10-TA-100
ESX10-TB-101
Circuit
Protection
Part Number
Current
Rating
(amps)
0.5
6720005305
1
6720005301
2
3
ESX10-TB-102
N/O
Contact
Part Number
Current
Rating
(amps)
0.5
6720005320
1
6720005321
6720005302
2
6720005303
3
4
6720005304
6
x
x
ESX10-TB-114*
N/C
Contact
Part Number
Current
Rating
(amps)
0.5
6720005340
1
6720005341
6720005322
2
6720005323
3
4
6720005324
6720005306
6
8
6720005308
10
12
ESX10-TB-124**
Control
Input
Part Number
Current
Rating
(amps)
0.5
6720005360
1
6720005361
6720005342
2
6720005343
3
4
6720005344
6720005326
6
8
6720005328
6720005310
10
6720005312
12
* Control force input on/off
Status OUT
ØV = OK
x
x
ESX10-TB-114
Current
Rating
(amps)
Signal contact
single signal
single signal
N/O
N/C
(normally open NO)
(normally closed NC)
ESX10-TB-127
Reset
Input
Part Number
Current
Rating
(amps)
0.5
6720005380
0.5
6720005309
1
6720005381
1
6720005319
6720005362
2
6720005382
2
6720005329
6720005363
3
6720005383
3
6720005339
4
6720005364
4
6720005384
4
6720005349
6720005346
6
6720005366
6
6720005386
6
6720005369
8
6720005348
8
6720005368
8
6720005388
8
6720005389
6720005330
10
6720005350
10
6720005370
10
6720005390
10
6720005399
6720005332
12
6720005352
12
6720005372
12
6720005392
12
6720005313
** Reset input only to reset under fault conditions
44
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
Reset
Input
Part Number
E l e c t ro n i c C i rc u i t P ro t e c t i o n E S X 1 0 - T
ESX10-T Signal inputs / outputs (wiring diagram)
ESX10-TA-100
without signal input/output
1
LINE+
2
ESX10-TB-101
without signal input
with signal output F
(single signal, N/O)
LINE+
LOAD+
1
SF 23
13
11
IN 21
LOAD+
0V
2
3
operating condition: 13-14 closed
fault condition:
13-14 open
LINE+
LINE+
LOAD+
0V
2
LOAD+
0V
3
operating condition: 11-12 open
fault condition:
11-12 closed
1
3
operating condition: SF +24 V = OK
fault condition:
SF 0 V
Dimensions
12.5
.492
83
3.27
1
LINE
LINE
LOAD
LOAD
SF 23
RE 22
2
ESX10-TB-127
with reset input RE
(+DC 24 V ↓)
with inverse status output SF
(0 V = load output ON)
1
SF 23
LINE+
1
12
3
ESX10-TB-124
with reset input RE
(+24VDC ↓)
with status output SF
(+24 V = load output ON)
LINE+
14
2
0V
ESX10-TB-114
with control input IN+
(+24VDC)
with status output SF
(+24 V = load output ON)
ESX10-TB-102
without signal input
with signal output F
(single signal, N/C)
LOAD+
0V
2
3
80
3.15
RE 22
LOAD+
0V
operating condition: SF +24 V = O
fault condition:
SF 0 V
80
3.15
3
operating condition: SF 0 V = OK
fault condition:
SF +24 V
label
snap-on socket for
symmetrical rail EN 50022-35x7.5
mm
This is a metric design and millimeter dimensions take precedence ( inch )
45
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
E l e c t ro n i c C i rc u i t P ro t e c t i o n E S X 1 0 - T
Time/Current characteristic curve (Ta = 25 °C)
• The trip time is typically 3 s in the range between 1.1 and 1.8
x In*1).
disconnection
typically 1.1 x In 1.8 x In *1)
• Electronic current limitation occurs at typically 1.8 x In*1) which
means that under all overload conditions (independent of the
power supply and the resistance of the load circuit) the max.
overload before disconnection will not exceed 1.8 x In*1) times
the current rating. Trip time is between 100 ms and 3 sec
(depending on overload or at short circuit).
10000
1000
100
trip time in seconds
current limitation *1)
typically 1.8 x In
10
5
• Without this current limitation a considerably higher overload
current would flow in the event of an overload or short circuit.
1
0.1
0.01
0
1
2
3
5 IK
4
...times rated current
*1)
current limitation typically 1.8 x In times rated current at In = 0.5 A...6 A
current limitation typically 1.5 x In times rated current at In = 8 A or 10 A
current limitation typically 1.3 x In times rated current at In = 12 A
Table 3: Reliable trip of ESX10-T
Reliable trip of ESX10-T with different cable lengths and cross sections
Resistivity of copper ρ0 =
Ub = DC 19.2 V (= 80 % of 24 V)
0.0178 (Ohm x mm2) / m
voltage drop of ESX10-T and tolerance of
trip point (typically 1.1 x In = 1.05 ... 1.35 x In) have been taken into account.
ESX10-T-selected rating In (in A)
3
6
e. g. trip current Iab = 1.25 x In (in A)
3.75
7.5
Rmax in Ohm = (Ub / Iab) - 0.050
5.07
2.51
The ESX10-T reliably trips from 0 Ohm to max. circuitry resistance Rmax
Cable cross section A in mm2
cable length L in meter
(= single length)
0.14
ESX10-T trips after 3 s
0.25
0.34
0.5
0.75
1
1.5
cable resistance in Ohm = (R0 x 2 x L) / A
5
1.27
0.71
0.52
0.36
0.24
0.18
0.12
10
2.54
1.42
1.05
0.71
0.47
0.36
0.24
15
3.81
2.14
1.57
1.07
0.71
0.53
0.36
20
5.09
2.85
2.09
1.42
0.95
0.71
0.47
25
6.36
3.56
2.62
1.78
1.19
0.89
0.59
30
7.63
4.27
3.14
2.14
1.42
1.07
0.71
35
8.90
4.98
3.66
2.49
1.66
1.25
0.83
40
10.17
5.70
4.19
2.85
1.90
1.42
0.95
45
11.44
6.41
4.71
3.20
2.14
1.60
1.07
50
12.71
7.12
5.24
3.56
2.37
1.78
1.19
75
19.07
10.68
7.85
5.34
3.56
2.67
1.78
100
25.34
14.24
10.47
7.12
4.75
3.56
2.37
125
31.79
17.80
13.09
8.90
5.93
4.45
2.97
150
38.14
21.36
15.71
10.68
7.12
5.34
3.56
175
44.50
24.92
18.32
12.46
8.31
6.23
4.15
200
50.86
28.48
20.94
14.24
9.49
7.12
4.75
225
57.21
32.04
23.56
16.02
10.68
8.01
5.34
250
63.57
35.60
26.18
17.80
11.87
8.90
5.93
Example 1:
max. length at 1.5 mm2 and 3 A
Example 2:
max. length at 1.5 mm2 and 6 A
106 m
Example 3:
mixed wiring:
(Control cabinet – sensor/actuator level)
R1 = 40 m in 1.5 mm2 and R2 = 5 m in 0.25 mm2:
R1 = 0.95 Ohm, R2 = 0.71 Ohm
Total (R1 + R2) = 1.66 Ohm
214 m
46
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
E l e c t ro n i c C i rc u i t P ro t e c t i o n E S X 1 0 - T
Mounting examples for ESX10-T
The ESX10-T features an integral power distribution system.
LINE+ busbar
6720005315
(12.5 x n)-3 = length of busbars ± 0.5
e. g. (12.5 x 5)-3 = 59.5 ± 0.5
continuous busbar
500 mm length, cut
Up to 40 pole
signal bar
6720005316
or
jumper
6720005317
(2 pole only)
remove protection
against brush contact
located on bottom side
side walls or barriers for protection
against brush contact on LINE+ and
OV jumper locations
insert protection against
brush contact
0V busbar
6720005315
12.5 x n = width of protector block
e. g. 12.5 x 5 = 62.5
insert busbars
and protection slides
to be flush with housing sides
insert signal
bars to be flush with
housing and place them
centrally over the contacts
5 ESX10-TB
with busbars
and jumpers
5 ESX10-TA
with busbars
Mounting procedure:
Before wiring insert busbars into protection block.
47
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
E l e c t ro n i c C i rc u i t P ro t e c t i o n E S X 1 0 - T
Connection diagrams and application examples ESX10-T
Signal contacts are shown in OFF or fault concition.
ESX10-TA-100
ESX10-TB-101
group signaling (series connection)
terminals for
busbars
screw
terminals
+ line entry for the SI
+ line entry
+ line entry
LINE+ busbar
1
LINE+
1
LINE+
+24V
1
LINE+
LINE + busbar
1
LINE+
+24V
14
13
1
LINE+
1
LINE+
14
13
14
13
group signalling
by means of an LED
power supply
DC 24 V
ESX10-TA-100
ESX10-TA-100
ESX10-TA-100
power supply
DC 24 V
0V
2 LOAD+
2 LOAD+
jumpers are staggered
3 0V
3 0V
3 0V
0V
ESX10-TB-101
ESX10-TB-101
ESX10-TB-101
2 LOAD+
2 LOAD+
2 LOAD+
2 LOAD+
3 0V
3 0V
3 0V
0 V busbar
0 V busbar
- line entry
- line entry
+
load
-
+
-
+
load
load
-
+
-
+
load
ESX10-TB-102
ESX10-TB-124
Single signaling with common line entry
Single signaling with common reset
+
-
load
reset
button
single signalling per way
by means of an LED
+ line entry
for the SI
-
load
single signalling per way
by means of an LED
+ line entry
+ line entry
LINE+ busbar
LINE+ busbar
1
LINE+
1
LINE+
+24V
12
11
1
LINE+
12
11
12
11
power supply
DC 24 V
22
signal busbar for
common line entry
ESX10-TB-102
ESX10-TB-102
0V
2 LOAD+
2 LOAD+
2 LOAD+
3 0V
3 0V
RE
23
SF
22
RE
SF
1
LINE+
23
22
RE
SF
ESX10-TB-124
0V
ESX10-TB-124
ESX10-TB-124
2 LOAD+
2 LOAD+
2 LOAD+
3 0V
3 0V
3 0V
- line entry
+
load
-
+
load
-
+
load
-
signal busbar for
common reset
0 V busbar
0 V busbar
- line entry
23
power supply
DC 24 V
ESX10-TB-102
3 0V
1
LINE+
1
LINE+
+24V
+
load
-
+
load
-
+
load
48
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
-
E l e c t ro n i c C i rc u i t P ro t e c t i o n E S X 1 0 - T
Accessories for ESX10-T
Description
Description
Busbars for LINE+ and 0 V
Part No.
6720005315
max. load with one line entry
(recommended: centre line entry)
Imax
50 A
• LINE +(24VDC)
max. load with two line entries
Imax
63 A
•0V
length:
500 mm
Signal busbars for signal contacts
and reset inputs
6720005316
max. load with one line entry
Imax
1A
with one series connection of signal contacts
Imax
0.5 A
length:
500 mm
Jumpers for signal contacts
6720005317
length:
21 mm
packing unit:
10 pcs
TS32 rail adapter
9102100000
The ESX10-T features an integral power distribution system.
The following wiring modes are possible with various pluggable current and signal busbars:
Caution: The electronic devices ESX10-T require
a 0 V connection
• signal contacts
• reset inputs
(Remove protection walls/barriers before using adapter.)
For detailed installation instructions and approvals contact
Weidmuller at 1-800-849-9343 or go to www.weidmuller.com
49
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
I n t ro d u c t i o n — C i rc u i t P ro t e c t i o n
Weidmuller’s DIN-rail mounted circuit breakers are available for use in applications where circuit protection must
be able to distinguish between circuit overloads and short
circuits. Each circuit breaker has the ability to be reset
without the need to change components. All circuit
breakers are available with an assortment of jumpers and
marking tags.
Circuit breakers in the 9926
Series are cULus listed
according to UL489 and
CSA 22.2 No. 5.02, CE,
VDE. The hydraulic magnetic trip mechanism offers
10,000A of interrupting
capacity in 120V and 240V,
50/60Hz applications.
9926 Series
The CB4200 Series of
thermal magnetic circuit
breakers feature a pushbutton style of trip reset.
This reset provides a
visual indication of status
which allows for rapid
troubleshooting.
The CB2200 Series feature
integrated alarm contacts
within a narrow profile,
thereby allowing increased
enclosure capacity. All of
these circuit breakers
demonstrate consistent
reliability through 100%
calibration and testing, and
feature a touch safe design
to prevent injury from accidental contact with live
components.
CB2200 Series
The CB9100 Series of
thermal magnetic circuit
breakers provide a rugged
and industry-standard form
factor (18 mm/pole). For
supplemental circuit
protection.
CB4200 Series
CB9100 Series
50
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
9 9 2 6 S e r i e s B r a n c h R a t e d C i rc u i t B re a k e r s – A C Ve r s i o n
Circuit Breakers
Hydraulic Magnetic Type
9926 Series
Double Pole
Single pole and double pole versions
120/240 VAC, 50/60 Hz
Up to 25A
Just 13 mm wide
Mounts on 35mm DIN-rail
cULus listed according to UL489 CSA C22.2
No. 5.02, CE, VDE
Ordering Data
Type: Single Pole (up to 120 VAC)
Current Ratings
Part No.
(amps)
TS 35
0.5
9926251000
Technical Data
Description
QL-1-13-DM-KM-0.5
Part No.
TS 35
9926252000
Description
QL-2-13-DM-KM-0.5
1
2
9926251001
9926251002
QL-1-13-DM-KM-01
QL-1-13-DM-KM-02
1
2
9926252001
9926252002
QL-2-13-DM-KM-01
QL-2-13-DM-KM-02
3
4
5
9926251003
9926251004
9926251005
QL-1-13-DM-KM-03
QL-1-13-DM-KM-04
QL-1-13-DM-KM-05
3
4
5
9926252003
9926252004
9926252005
QL-2-13-DM-KM-03
QL-2-13-DM-KM-04
QL-2-13-DM-KM-05
6
9926251006
QL-1-13-DM-KM-06
6
9926252006
QL-2-13-DM-KM-06
7
8
9926251007
9926251008
QL-1-13-DM-KM-07
QL-1-13-DM-KM-08
7
8
9926252007
9926252008
QL-2-13-DM-KM-07
QL-2-13-DM-KM-08
10
13
9926251010
9926251013
QL-1-13-DM-KM-10
QL-1-13-DM-KM-13
10
13
9926252010
9926252013
QL-2-13-DM-KM-10
QL-2-13-DM-KM-13
15
16
20
25
9926251015
9926251016
9926251020
9926251025
QL-1-13-DM-KM-15
QL-1-13-DM-KM-16
QL-1-13-DM-KM-20
QL-1-13-DM-KM-25
15
16
20
25
9926252015
9926252016
9926252020
9926252025
QL-2-13-DM-KM-15
QL-2-13-DM-KM-16
QL-2-13-DM-KM-20
QL-2-13-DM-KM-25
9926 Series AC Version - dimensions in mm (in.)
Voltage
Current
minimum
120/240 VAC, 50/60Hz
Although the 9926 series uses a magnetic only trip mechanism, CSA
testing indicates a trip characteristic similar to thermal magnetic trip
mechanisms. No de-rating is required at elevated temperatures.
Additional trip curves and amp ratings are available
upon request.
Tripping Time
10
10
1
Seconds
1
1
0.1
0.1
0.01
0.01
0.001
0.001
4000
5000
0.4
1
10
2000
2500
3000
0.6
10
Ambient Temperature 30°C
1500
1.5
Ambient Temperature 30°C
1000
4
100
Minutes
100
400
500
28
Operating Characteristics
Curve KM
Operating Characteristics
Curve 1
300
90
1000
1000
100
105
125
150
200
125% 150% 200% 400% 600% 800% 1000%
minimum 15
8
4
0.7
0.09 0.007 0.005
(sec)
9926 Series–AC version Trip Curve
4000
5000
Sample trip characteristics - KM
57
(2.24)
9926 Series–AC version Trip Curve
Tripping Time
Trip Curves—Hydraulic Magnetic Type
Typical time/current characteristics at 30ºC
45
(1.77)
64.8
(2.55)
*Wire sizes: gauges specified are the minimum allowable as per CSA
and UL standards.
The 9926 circuit breakers do not have provisions for marking tags.
A possible solution is to cut the adhesive SchS2 tag rail to length
(approximately 20 mm on a single pole unit so the current rating
remains visible or approximately 30 mm on a two pole unit).
The SchS2 accepts DEK, WS and ESG 8/17 marking tags.
The part number for adhesive SchS2 is 1720600000.
92.8
(3.65)
28.5
(1.12)
5
(0.2)
2000
2500
3000
67101960
67101961
67101913
13
(0.51)
1500
Power lug, straight
Power lug, 90°
Lock-out handle
26
(1.02)
32
(1.26)
400
500
67101973
67101974
13
(0.51)
19
(0.75)
300
Bus-bar end cap, 1 pole
Bus-bar end cap, 2 pole
71.4
(2.81)
Operating temperature
-40…+65°C
Wire size*
0.5-15A:
14AWG min., 10AWG max.
20-25A:
10AWG min.
Torque
20 in.-lb
Approval
cULus listed according to UL489 CSA C22.2 No. 5.02, CE, VDE
Accessories
Part No.
Bus-bar (1 pole, insulated, 1 m)
67101904
Bus-bar (2 pole, insulated, 1 m)
67101972
Minutes
100MM
10000 mechanical operations
100
105
130
150
200
Insulation resistance
Operating life
66
(2.6)
Seconds
25A
10,000A
1500V, 50/60Hz
17.9
(0.7)
74
(2.91)
0.5A
maximum
Interrupting capacity
Dielectric strength
maximum 300
(sec)
Type: Double Pole (up to 240 VAC)
Current Ratings
(amps)
0.5
1000
•
•
•
•
•
•
9926 Series
Single Pole
(%) Rated Current
(%) Rated Current
Trip Curve 1 applies to the following part numbers where
"XX" is the current rating:
Single Pole— 99262512XX
Double Pole— 99262522XX
51
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
9 9 2 6 S e r i e s B r a n c h R a t e d C i rc u i t B re a k e r s – A C Ve r s i o n w i t h C o n t a c t s
Circuit Breakers with
Auxiliary switch, Trip alarm,
Combination of both
9926 Series
Single Pole
w/ Auxiliary Contact†
9926 Series
Single Pole Trip
(Alarm Contact)
9926 Series
Single Pole Combination
(Auxiliary & Alarm Contact)†
• AC voltages (120/240V)
• Single and double pole versions
• cULus listed according to UL489
and C22.2 No. 5.02, CE, VDE
• Factory fitted auxiliary or trip alarm
• Compact 6.5mm width
• Attached to right hand side of circuit breaker
Technical Data
Type: Single Pole Aux (up to 120 VAC)
Voltage
120/240 VAC, 50/60Hz
Current
minimum
maximum
Current
Ratings
(amps) Part No.
1 9926261001
2 9926261002
5 9926261005
10 9926261010
15 9926261015
20 9926261020
25 9926261025
0.5A
25A
Interrupting capacity
10,000A
Dielectric strength
Insulation resistance
Operating life
1500V, 50/60Hz
100MM
10000
mechanical operations
Operating temperature
-40…+65°C
Description
QL-A-1-13-DM-KM-1
QL-A-1-13-DM-KM-2
QL-A-1-13-DM-KM-5
QL-A-1-13-DM-KM-10
QL-A-1-13-DM-KM-15
QL-A-1-13-DM-KM-20
QL-A-1-13-DM-KM-25
Type: Single Pole Combo (up to 120 VAC)
Type: Single Pole Trip (up to 120 VAC)
Current
Ratings
(amps) Part No.
1
9926271001
2
9926271002
5
9926271005
10 9926271010
15 9926271015
20 9926271020
25 9926271025
Current
Ratings
(amps) Part No.
1
9926281001
2
9926281002
5
9926281005
10 9926281010
15 9926281015
20 9926281020
25 9926281025
Description
QL-T-1-13-DM-KM-1
QL-T-1-13-DM-KM-2
QL-T-1-13-DM-KM-5
QL-T-1-13-DM-KM-10
QL-T-1-13-DM-KM-15
QL-T-1-13-DM-KM-20
QL-T-1-13-DM-KM-25
Description
QL-AT-1-13-DM-KM-1
QL-AT-1-13-DM-KM-2
QL-AT-1-13-DM-KM-5
QL-AT-1-13-DM-KM-10
QL-AT-1-13-DM-KM-15
QL-AT-1-13-DM-KM-20
QL-AT-1-13-DM-KM-25
Wire size*
0.5-15A:
20-25A:
Torque
14AWG min., 10AWG max.
10AWG min.
20 in.-lb
9926 Series
Double Pole Trip
(Alarm Contact)
9926 Series
Double Pole
w/ Auxiliary Contact†
Approval
cULus listed according to UL489 and C22.2
No. 5.02, CE, VDE
9926 Series
Double Pole Combination
(Auxiliary & Alarm Contact)†
†UL 489 listed
(5A, 250 VAC; 0.5A, 80 VDC Auxiliary; 0.5A,
125 VDC Trip Alarm)
IEC 60947-5-1 Approved
(5A, 250 VAC; 0.5A, 110 VDC Auxiliary; 0.5A,
125 VDC Trip Alarm)
*Wire sizes: gauges specified are the minimum
allowable as per CSA and UL standards.
The 9926 circuit breakers do not have provisions for
marking tags. A possible solution is to cut the adhesive
SchS2 tag rail to length (approximately 20 mm on a single pole unit so the current rating remains visible or
approximately 30 mm on a two pole unit). The SchS2
accepts DEK, WS and ESG 8/17 marking tags. The
part number for adhesive SchS2 is 1720600000.
Type: Double Pole Aux (up to 240 VAC)
Current
Ratings
(amps) Part No.
1
9926262001
2
9926262002
5
9926262005
10 9926262010
15 9926262015
20 9926262020
25 9926262025
Description
QL-A-2-13-DM-KM-1
QL-A-2-13-DM-KM-2
QL-A-2-13-DM-KM-5
QL-A-2-13-DM-KM-10
QL-A-2-13-DM-KM-15
QL-A-2-13-DM-KM-20
QL-A-2-13-DM-KM-25
Part No.
Description
9926272001 QL-T-2-13-DM-KM-1
9926272002 QL-T-2-13-DM-KM-2
9926272005 QL-T-2-13-DM-KM-5
9926272010 QL-T-2-13-DM-KM-10
9926272015 QL-T-2-13-DM-KM-15
9926272020 QL-T-2-13-DM-KM-20
9926272025 QL-T-2-13-DM-KM-25
Dual Mount Dimensions in mm (in.)
1000
Operating Characteristics
Curve KM
(N/O)16
(N/C)18
(C)15
Ambient Temperature 30°C
TRIP ALARM Q. CONNECTORS
21.1
(0.83)
10
5.5
(0.22)
0.5
(0.02)
Tripping Time
Minutes
100
31.3
(1.23)
26.2
(1.03)
57.0
(2.24)
1
10
7
(0.28)
0.1
21.3
(0.84)
0.01
32.9
(1.3)
10.7
(0.42)
0.5
(0.02)
2.8
(0.11)
11(C)
Seconds
14(N/O)
AUX SWITCH Q. CONNECTORS
1
12(N/C)
Trip Curves—Hydraulic
Magnetic Type Typical
time/current characteristics
at 30ºC
Additional trip curves and
amp ratings are available
upon request.
Type: Double Pole Combo (up to 240 VAC)
Current
Ratings
(amps) Part No.
1
9926282001
2
9926282002
5
9926282005
10 9926282010
15 9926282015
20 9926282020
25 9926282025
2
(0.08)
9926 Series–AC version Trip Curve
Type: Double Pole Trip (up to 240 VAC)
Current
Ratings
(amps)
1
2
5
10
15
20
25
4000
5000
2000
2500
3000
1500
1000
400
500
300
100
105
125
150
200
0.001
(%) Rated Current
52
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
Description
QL-AT-2-13-DM-KM-1
QL-AT-2-13-DM-KM-2
QL-AT-2-13-DM-KM-5
QL-AT-2-13-DM-KM-10
QL-AT-2-13-DM-KM-15
QL-AT-2-13-DM-KM-20
QL-AT-2-13-DM-KM-25
9 9 2 6 S e r i e s B r a n c h R a t e d C i rc u i t B re a k e r s – D C Ve r s i o n
Circuit Breakers
Hydraulic Magnetic Type
9926 Series
Single Pole
(80 VDC)
9926 Series
Single Pole
(125 VDC)
• Single pole versions only
• U2 trip curve for general purpose
applications
• 80 and 125 VDC
• Up to 60A
• Just 13 mm wide
• Mounts on 35mm DIN-rail
• UL 489A listed
• VDE
Type: Single Pole (80 VDC)
Current
Ratings
(amps)
0.5
1
2
3
4
5
10
15
20
25
30
35
40
45
50
60
Accessories
Part No.
9926251900
Description
QY-1-13-DM-U2-0.5
9926251901
9926251902
9926251903
QY-1-13-DM-U2-01
QY-1-13-DM-U2-02
QY-1-13-DM-U2-03
9926251904
9926251905
QY-1-13-DM-U2-04
QY-1-13-DM-U2-05
9926251910
QY-1-13-DM-U2-10
9926251915
9926251920
9926251925
QY-1-13-DM-U2-15
QY-1-13-DM-U2-20
QY-1-13-DM-U2-25
9926251930
9926251935
QY-1-13-DM-U2-30
QY-1-13-DM-U2-35
9926251940
9926251945
9926251950
9926251960
QY-1-13-DM-U2-40
QY-1-13-DM-U2-45
QY-1-13-DM-U2-50
QY-1-13-DM-U2-60
9926 Series–DC version Trip Curve
9926251805
QY-1-13-DM-U2-05-B1
9926251810
9926251815
QY-1-13-DM-U2-10-B1
QY-1-13-DM-U2-15-B1
9926251820
9926251825
QY-1-13-DM-U2-20-B1
QY-1-13-DM-U2-25-B1
9926251830
QY-1-13-DM-U2-30-B1
9926251835
9926251840
9926251845
QY-1-13-DM-U2-35-B1
QY-1-13-DM-U2-40-B1
QY-1-13-DM-U2-45-B1
9926251850
9926251860
QY-1-13-DM-U2-50-B1
QY-1-13-DM-U2-60-B1
74
(2.91)
66
(2.6)
13
(0.51)
28.5
(1.12)
92.8
(3.65)
Ambient Temperature 30°C
57
(2.24)
Minutes
Tripping Time
10
1
10
19
(0.75)
1
32
(1.26)
0.1
5
(0.2)
45
(1.77)
64.8
(2.55)
0.01
4000
5000
300
0.001
100
105
130
150
200
10,000 A
1500 V, 50/60 Hz
100 MM
10000
mechanical operations
Operating temperature
-40…+65°C
Wire size*
1-15A:
14 AWG min.,
10 AWG max.
20-25A:
10 AWG min.
Torque
20 in.-lb
Approval
UL 489A Listed, CE, VDE
Seconds
Interrupting capacity
Dielectric strength
Insulation resistance
Operating life
QY-1-13-DM-U2-02-B1
QY-1-13-DM-U2-03-B1
QY-1-13-DM-U2-04-B1
Dimensions in mm (in.)
Operating Characteristics
Curve U2 DC
(4% Ripple Factor)
100
80,125 VDC
0.5 A
60 A
9926251802
9926251803
9926251804
71.4
(2.81)
1000
Technical Data
minimum
maximum
Description
QY-1-13-DM-U2-01-B1
Additional trip curves and amp ratings
are available upon request.
2000
2500
3000
67101973
67101960
67101961
67101913
1500
Bus bar end cap, 1 pole
Power lug, straight
Power lug, 90°
Lock-out handle
Part No.
9926251801
Trip Curves—Hydraulic
Magnetic Type Typical
time/current characteristics
at 30ºC
1000
Part No.
67101904
400
500
Type
Bus-bar (1 pole, insulated 1m)
Voltage
Current
Type: Single Pole (125 VDC)
Current
Ratings
(amps)
1
2
3
4
5
10
15
20
25
30
35
40
45
50
60
17.9
(0.7)
Ordering Data
(%) Rated Current
*Wire sizes: gauges specified are the minimum allowable as per CSA and UL standards.
The 9926 circuit breakers do not have provisions for
marking tags. A possible solution is to cut the adhesive
SchS2 tag rail to length (approximately 20 mm on a single pole unit so the current rating remains visible or
approximately 30 mm on a two pole unit). The SchS2
accepts DEK, WS and ESG 8/17 marking tags. The
part number for adhesive SchS2 is 1720600000.
53
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
9 9 2 6 S e r i e s S u p p l e m e n t a l C i rc u i t B re a k e r s
Circuit Breakers
Hydraulic Magnetic Type
9926 Series
Single Pole
9926 Series
Double Pole
9926 Series
Triple Pole
• AC Voltages 277/480V
• Trip curve 2 for general purpose
applications
• UL 1077 recognized
• VDE approved and CE marked
• Just 13 mm wide
• Mounts to 35 mm DIN-rail
• Factory fitted auxiliary or trip alarm
• Single, double and triple pole versions
Ordering Data
Type: Single Pole (up to 277 VAC)
Current
Ratings
(amps)
1
2
3
4
5
6
8
10
15
20
25
35
40
50
60
Accessories
Description
QZ-1-13-D-2-01
QZ-1-13-D-2-02
9926251503
QZ-1-13-D-2-03
9926251504
9926251505
9926251506
QZ-1-13-D-2-04
QZ-1-13-D-2-05
QZ-1-13-D-2-06
9926251508
9926251510
QZ-1-13-D-2-08
QZ-1-13-D-2-10
9926251515
QZ-1-13-D-2-15
9926251520
9926251525
9926251535
9926251540
9926251550
QZ-1-13-D-2-20
QZ-1-13-D-2-25
QZ-1-13-D-2-35
QZ-1-13-D-2-40
QZ-1-13-D-2-50
9926251560
QZ-1-13-D-2-60
Part No.
Description
9926252501
9926252502
QZ-2-13-D-2-01
QZ-2-13-D-2-02
9926252504
QZ-2-13-D-2-04
9926252505
9926252506
9926252510
QZ-2-13-D-2-05
QZ-2-13-D-2-06
QZ-2-13-D-2-10
9926252515
9926252520
QZ-2-13-D-2-15
QZ-2-13-D-2-20
9926252525
QZ-2-13-D-2-25
9926252530
9926252535
9926252540
9926252550
9926252560
QZ-2-13-D-2-30
QZ-2-13-D-2-35
QZ-2-13-D-2-40
QZ-2-13-D-2-50
QZ-2-13-D-2-60
Type: Triple Pole (up to 480 VAC)
Current
Rating
(amps)
10
15
20
25
30
40
50
60
Part No.
Description
9926253510
9926253515
QZ-3-13-D-2-10
QZ-3-13-D-2-15
9926253520
QZ-3-13-D-2-20
9926253525
9926253530
9926253540
QZ-3-13-D-2-25
QZ-3-13-D-2-30
QZ-3-13-D-2-40
9926253550
9926253560
QZ-3-13-D-2-50
QZ-3-13-D-2-60
9926 Series Supplemental – dimensions in mm (in.)
65
(2.56)
13
(0.51)
60
(2.36)
26
(1.02)
39
(1.54)
92.8
(3.65)
25.9
(0.94)
45
(1.77)
44
(1.73)
13
(0.51)
63.8
(2.51)
73
(2.87)
9926 Series–Supplemental Trip Curve
Trip Curves—Hydraulic
Magnetic Type Typical
time/current characteristics
at 30ºC
1
10
1
0.1
0.01
(%) Rated Current
†cURus recognized to UL1077 and C22.2 No. 235
54
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
4000
5000
2000
2500
3000
1500
1000
0.001
400
500
The 9926 circuit breakers do not have provisions for marking tags. A possible solution is to cut the adhesive
SchS2 tag rail to length (approximately 20 mm on a single pole unit so the current rating remains visible or
approximately 30 mm on a two pole unit).The SchS2 accepts DEK, WS and ESG 8/17 marking tags.
The part number for adhesive SchS2 is 1720600000.
Ambient Temperature 30°C
10
300
*Wire sizes: gauges specified are the minimum allowable as per CSA and UL standards.
Operating Characteristics
Curve 2
100
Minutes
Additional trip curves and
amp ratings are available
upon request.
1000
100
105
130
150
200
Technical Data
Voltage
277/480 VAC @ 50/60 Hz
Current
minimum
0.5 A
maximum
60 A
Interrupting capacity
5 kA @ 277/480 V, 5 kA @ 120 V, 5 kA @ 240 V
Dielectric strength
1500 V, 50/60 Hz
Insulation resistance
100 MM
Operating life
10000 mechanical operations
Operating temperature
-40…+65°C
Wire size*
1-15A:
14 AWG min., 10 AWG max.
20-25A:
10 AWG min.
Torque
20 in.-lb
Approval
†UL 1077 Recognized, VDE (EN 60947-2) Approved, CSA C22.2 No. 235, CE Marked
Tripping Time
5.0
(0.2)
13
(0.51)
Seconds
Part No.
67101904
67101972
67101971
67101973
67101974
67101960
67101961
67101913
22.5
(0.86)
Type
Bus bar (1 pole, insulated 1m)
Bus bar (2 pole, insulated 1m)
Bus bar (3 pole, insulated 1m)
Bus bar end cap, 1 pole
Bus bar end cap, 2 pole or 3 pole
Power lug, straight
Power lug, 90°
Lock-out handle
Part No.
9926251501
9926251502
Type: Double Pole (up to 480 VAC)
Current
Rating
(amps)
1
2
4
5
6
10
15
20
25
30
35
40
50
60
9 9 2 6 S e r i e s S u p p l e m e n t a l C i rc u i t B re a k e r s w i t h C o n t a c t s
Circuit Breakers
Auxiliary switch, Trip alarm,
Combination of both
9926 Series
Single Pole
w/ Auxiliary Contact‡
9926 Series
Single Pole Trip
(Alarm Contact)
9926 Series
Single Pole Combination
(Auxiliary & Alarm Contact)‡
• AC Voltages 277/480V
• Trip curve 2 for general purpose
applications
• UL 1077 recognized
• VDE approved and CE marked
• Just 13 mm wide
• Mounts to 35 mm DIN-rail
• Factory fitted auxiliary or trip alarm
• Single, double and triple pole versions
Type: Single Pole Aux (up to 277 VAC)
Technical Data
Voltage
277/480 VAC @ 50/60 Hz
Current
minimum
0.5 A
maximum
60 A
Interrupting capacity
5 kA @ 277/480 V,
5 kA @ 120 V, 5 kA @ 240 V
Dielectric strength
Insulation resistance
Operating life
1500 V, 50/60 Hz
100 MM
10000
mechanical operations
Operating temperature
-40…+65°C
Wire size*
1-15A:
Current
Ratings
(amps)
1
2
5
10
15
20
25
Part No.
9926261501
9926261502
Description
QZ-A-1-13-D-2-01
QZ-A-1-13-D-2-02
9926261505
9926261510
9926261515
QZ-A-1-13-D-2-05
QZ-A-1-13-D-2-10
QZ-A-1-13-D-2-15
9926261520
9926261525
QZ-A-1-13-D-2-20
QZ-A-1-13-D-2-25
Type: Single Pole Trip (up to 277 VAC)
Current
Ratings
(amps)
1
2
5
10
15
20
25
Part No.
9926271501
9926271502
Description
QZ-T-1-13-D-2-01
QZ-T-1-13-D-2-02
9926271505
9926271510
9926271515
QZ-T-1-13-D-2-05
QZ-T-1-13-D-2-10
QZ-T-1-13-D-2-15
9926271520
9926271525
QZ-T-1-13-D-2-20
QZ-T-1-13-D-2-25
Type: Single Pole Combo (up to 277 VAC)
Current
Ratings
(amps)
1
2
5
10
15
20
25
Part No.
9926281501
9926281502
Description
QZ-AT-1-13-D-2-01
QZ-AT-1-13-D-2-02
9926281505
9926281510
9926281515
QZ-AT-1-13-D-2-05
QZ-AT-1-13-D-2-10
QZ-AT-1-13-D-2-15
9926281520
9926281525
QZ-AT-1-13-D-2-20
QZ-AT-1-13-D-2-25
14 AWG min., 10 AWG max.
20-25A:
10 AWG min.
Torque
20 in.-lb
Approval
†UL 1077 Recognized, VDE (EN 60947-2)
Approved, CSA C22.2 No. 235, CE Marked
9926 Series
Double Pole
w/ Auxiliary Contact‡
9926 Series
Double Pole Trip
(Alarm Contact)
9926 Series
Double Pole Combination
(Auxiliary & Alarm Contact)‡
‡UL 489 listed
(5A, 250 VAC; 0.5A, 80 VDC Auxiliary; 0.5A,
125 VDC Trip Alarm)
IEC 60947-5-1 Approved
(5A, 250 VAC; 0.5A, 110 VDC Auxiliary; 0.5A,
125 VDC Trip Alarm)
*Wire sizes: gauges specified are the minimum allowable as per CSA and UL standards.
The 9926 circuit breakers do not have provisions for
marking tags. A possible solution is to cut the adhesive
SchS2 tag rail to length (approximately 20 mm on a
single pole unit so the current rating remains visible or
approximately 30 mm on a two pole unit). The SchS2
accepts DEK, WS and ESG 8/17 marking tags.The part
number for adhesive SchS2 is 1720600000.
9926 Series–Supplemental Trip Curve
Trip Curves—Hydraulic
Magnetic Type Typical
time/current characteristics
at 30ºC
1000
Type: Double Pole Aux (up to 480 VAC)
Current
Ratings
(amps)
1
2
5
10
15
20
25
Part No.
Description
9926262501
9926262502
QZ-A-2-13-D-2-01
QZ-A-2-13-D-2-02
9926262505
QZ-A-2-13-D-2-05
9926262510
QZ-A-2-13-D-2-10
9926262515
9926262520
9926262525
QZ-A-2-13-D-2-15
QZ-A-2-13-D-2-20
QZ-A-2-13-D-2-25
9926 Series
Triple Pole
w/ Auxiliary Contact‡
Type: Double Pole Trip (up to 480 VAC)
Current
Ratings
(amps)
1
2
5
10
15
20
25
Part No.
Description
9926272501
9926272502
QZ-T-2-13-D-2-01
QZ-T-2-13-D-2-02
9926272505
QZ-T-2-13-D-2-05
9926272510
QZ-T-2-13-D-2-10
9926272515
9926272520
9926272525
QZ-T-2-13-D-2-15
QZ-T-2-13-D-2-20
QZ-T-2-13-D-2-25
9926 Series
Triple Pole Trip
( Alarm Contact)
Type: Double Pole Combo (up to 480 VAC)
Current
Ratings
(amps)
1
2
5
10
15
20
25
Part No.
Description
9926282501
9926282502
QZ-AT-2-13-D-2-01
QZ-AT-2-13-D-2-02
9926282505
QZ-AT-2-13-D-2-05
9926282510
QZ-AT-2-13-D-2-10
9926282515
9926282520
9926282525
QZ-AT-2-13-D-2-15
QZ-AT-2-13-D-2-20
QZ-AT-2-13-D-2-25
9926 Series
Triple Pole Combination
(Auxiliary & Alarm Contact)‡
Operating Characteristics
Curve 2
Tripping Time
Minutes
100
Ambient Temperature 30°C
10
1
10
Seconds
1
Type: Triple Pole Aux (up to 480 VAC)
0.1
0.01
(%) Rated Current
†cURus recognized to UL1077 and C22.2 No. 235
4000
5000
2000
2500
3000
1500
1000
400
500
300
100
105
130
150
200
0.001
Current
Ratings
(amps)
1
2
5
10
15
20
25
Part No.
Description
9926263501
9926263502
9926263505
9926263510
9926263515
QZ-A-3-13-D-2-01
QZ-A-3-13-D-2-02
QZ-A-3-13-D-2-05
QZ-A-3-13-D-2-10
QZ-A-3-13-D-2-15
9926263520
9926263525
QZ-A-3-13-D-2-20
QZ-A-3-13-D-2-25
Type: Triple Pole Trip (up to 480 VAC)
Current
Ratings
(amps)
1
2
5
10
15
20
25
Part No.
Description
9926273501
9926273502
9926273505
9926273510
9926273515
QZ-T-3-13-D-2-01
QZ-T-3-13-D-2-02
QZ-T-3-13-D-2-05
QZ-T-3-13-D-2-10
QZ-T-3-13-D-2-15
9926273520
9926273525
QZ-T-3-13-D-2-20
QZ-T-3-13-D-2-25
Type: Triple Pole Combo (up to 480 VAC)
Current
Ratings
(amps)
1
2
5
10
15
20
25
Part No.
Description
9926283501
9926283502
9926283505
9926283510
9926283515
QZ-AT-3-13-D-2-01
QZ-AT-3-13-D-2-02
QZ-AT-3-13-D-2-05
QZ-AT-3-13-D-2-10
QZ-AT-3-13-D-2-15
9926283520
9926283525
QZ-AT-3-13-D-2-20
QZ-AT-3-13-D-2-25
55
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
9 9 2 6 S e r i e s S u p p l e m e n t a l C i rc u i t B re a k e r s – G F C I
Ground Fault Current Interrupt
Ordering Data
Description
73
(2.87)
65
(2.56)
QF17A2505 - CB W/GFI
QF17A2510 - CB W/GFI
QF17A2515 - CB W/GFI
QF17A2520
QF17A2525
QF17A2530
QF17A2550
-
CB
CB
CB
CB
W/GFI
W/GFI
W/GFI
W/GFI
9926 Series–AC version Trip Curve
Technical Data
Ground Leakage/GFCS
230 (CE) / 240 (UL)
5 kA
1000
Operating Characteristics
Curve 2
Minutes
100
44
(1.73)
Ambient Temperature 30°C
10
68.8
(2.71)
1
10
26
(1.02)
1
Seconds
Approval
UL 1077 and UL 1053, CE
–
0.26
2
-40 to +65ºC
Tripping Time
Withstand Capacity (kA)
Weight (kg)
Trip Curve (standard)
Operating Temperature
Trip Curves—Hydraulic Magnetic
Type Typical
time/current characteristics
at 30ºC
0.1
7.8
(0.307)
Standard Ampere Ratings (A)
5 to 50A
Sensitivity (mA)
30 (CE) / 22 (UL)
Number of Poles
1+N
Equipment Type
Rated Voltage (V)
Rated Interrupting/
9926 Series GFCI – dimensions in mm (in.)
Type: Single Pole GFCI
Current
Ratings
(amps) Part No.
5
9926291105
10
9926291110
15
9926291115
20
9926291120
25
9926291125
30
9926291130
50
9926291150
4000
5000
2000
2500
3000
1500
1000
400
500
300
100
105
130
150
200
0.001
16.4
(0.646)
8.0
(0.315)
71.4
(2.81)
0.01
26
(1.02)
•
(2.24)
•
•
57
•
CE approved
UL1077 and UL1053 recognized
Small frame size (26mm wide)
Single pole plus switched neutral
ground leakage protection
Trip point is unaffected by ambient
temperature
Current ratings up to 50A
Trip indication
(mid trip handle position)
Trip curve 2 for general purpose
applications
93
(3.66)
82.4
(3.24)
•
•
•
•
9926 Series
GFCI
(%) Rated Current
35.7
(1.406)
56
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
9926 Series Mounting Options and Accessories
Mounting Options
93%
95
ON
OFF
95
OF
F
ON
OF
F
ON
5 N VERT 45
W
ON
OFF
100%
ON
VERT D 4
O
R
5 N HO IZ DO 4
W
10
ON
OF F
ON
OF
F
%
ON
OF
F
5%
100%
HORIZ 4
5
OFF
UP
UP
It is important to note that in environments that are exposed to
a high degree of vibration, the cables that connect to the circuit
breaker must be securely held in place, as the breaker is not
designed to carry the weight of the cables. A maximum of 35N
can be applied to the terminal area, in a direction perpendicular
to the mounting axis.
%
%
If the product is not vertically mounted in the normal DIN-rail
mounting orientation, a rating factor must be applied. Figure 1
shows a diagram of the rating factor to apply. The published
curves for these circuit breaker products are produced with
the circuit breaker in the vertical mounting position. The rating
factor only applies to the must hold and must trip points of the
curve as the other parts (instantaneous trip point) stay largely
unaffected.
10
5
107%
Accessories
Technical Data
Current Rating
Voltage
Part Number Table - Example
80A max.
500V max.
Short Circuit Strength
25kA
Type
Part No.
Bus bar (1 pole, insulated 1m)
Bus bar (2 pole, insulated 1m)
Bus bar (3 pole, insulated 1m)
67101904
67101972
67101971
To order 9926 Series Single Pole Circuit Breaker
Part No. 9926251100
• Current Rating of 1.0 amp
• Internal Resistance per Pole of 1.1 ohms
• Trip Curve – M1, Medium (Standard)
9 9 2 6 2 5 1 0 0 0
Amperage
Type
"00" - 0.5A
"01" - 1A
"02" - 2A
Part No.
Bus bar end cap, 1 pole
Bus bar end cap, 2 pole or 3 pole
/
"60" - 60A
67101973
67101974
Trip Curves (Types 5-9)
"0" - Branch AC KM (Standard)
"1" - Branch AC OP (Instantaneous)
"2" - Branch AC 1 (Fast)
"3" - Supplemental 9 (Slow)
"4" - Branch 80VDC 1 (Fast)
"5" - Supplemental 2 (Standard)
"6" - Branch 125VDC OP (Instantaneous)
"7" - Branch 80VDC OP (Instantaneous)
"8" - Branch 125VDC U2 (Standard)
"9" - Branch 80VDC U2 (Standard)
Poles
1 Pole
2 Pole
3 Pole
Technical Data
Current Rating
Wire Size
Dimensions
Type
Power lug, straight
Power lug, 90°
85A max.
10 AWG min., 4 AWG max.
A: 6 mm B: 32 mm
Type
"5" - Base Breaker
"6" - With Auxiliary Contact
"7" - With Trip Alarm Contact
"8" - Combo Aux/Trip Contact
"9" - GFCI
Part No.
67101960
67101961
9 9 2 6 2 4 1 0 0 0
Amperage
Type
Lock-out handle
Part No.
67101913
"00" - 0.5A
"01" - 1A
"02" - 2A
/
"60" - 60A
Trip Curves (Type 4)
"0" - Supplemental 1 (Slow)
"1" - Supplemental 3 (Fast)
"3" - Branch AC 9 (Slow)
Poles
1 Pole
2 Pole
3 Pole
Type
"4" - Base Breaker
57
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
C B 4 2 0 0 S e r i e s S u p p l e m e n t a l C i rc u i t B re a k e r s
Circuit Breakers
Thermal Magnetic Type
CB4200 Series
Single Pole
CB4200 Series
Double Pole
• Rated from 0.05 to 16.0 amps
• Available in single or double pole configurations
• Features a tease free design to reduce contact
damage
• Offers push button trip/reset function
• Trip free design means the breaker cannot be held
closed against a fault
• Mounts on 32mm* or 35mm DIN-rail
• UL 1077 recognized
• CSA C22.2 No. 235
Ordering Data
Type: Single Pole
Type: Double Pole
Current
Ratings
(amps)
Part No. TS 35
*For TS 32 Rail,
see adapter below
Current
Ratings
(amps)
Part No. TS 35
*For TS 32 Rail,
see adapter below
0.05
9124083500
0.05
9124223500
0.08
9124653500
0.08
9124233500
0.1
9104173500
0.1
9120353500
0.2
0.3
0.4
9104183500
9129813500
9124093500
0.2
0.3
0.4
9124243500
9124263500
9124273500
0.5
9101003500
0.5
9129583500
0.6
9124113500
0.6
9124283500
0.7
0.8
1.0
1.2
1.3
9129563500
9101103500
9101203500
9101303500
9124123500
0.7
0.8
1.0
1.2
1.3
9124293500
9129593500
9129613500
9129623500
9124313500
1.4
1.5
9124133500
9101403500
1.4
1.5
9124323500
9129633500
1.8
2.0
2.5
3.0
3.5
9124143500
9101503500
9101603500
9101703500
9124163500
1.8
2.0
2.5
3.0
3.5
9124333500
9129643500
9129653500
9129663500
9124343500
4.0
4.5
5.0
9104353500
9124173500
9101803500
4.0
4.5
5.0
9129713500
9124353500
9129673500
5.5
6.0
6.5
7.0
8.0
9107833500
9103813500
9120043500
9104153500
9103003500
5.5
6.0
6.5
7.0
8.0
9124363500
9124373500
9124383500
9124393500
9104673500
9.0
10.0
9104613500
9101903500
9.0
10.0
9124423500
9129683500
11.0
12.0
9124183500
9107843500
11.0
12.0
9124433500
9124443500
13.0
14.0
15.0
16.0
9124193500
9107853500
9102003500
9124213500
13.0
14.0
15.0
16.0
9124453500
9124463500
9129693500
9124473500
Trip Curves
Thermal Magnetic Type
Typical time/current characteristics at 23ºC
CB4200 Series
*Adapter foot – dimensions in mm (in.)
M1+
0.05 to 7.5 A
100
Trip time in seconds
100
Trip time in seconds
1,000
10
1
10
TS32 adapter
0.1
0.01
0.01
0.001
2
3
4
6
8 10
20 30
… times rated current
50 70 100
9102100000
1
0.1
0.8 1
–30°C
+23°C
+55°C
20
–30°C
+23°C
+55°C
1,000
0.001
8 to 16 A
10,000
(.787)
M1+
10,000
0.8 1
2
3
4
6
8 10
20 30
50 70 100
… times rated current
58
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
C B 4 2 0 0 S e r i e s S u p p l e m e n t a l C i rc u i t B re a k e r s
CB4200 Series
Single Pole
CB4200 Series
Double Pole
Internal Wiring Diagram
Internal Wiring Diagram
Dimensions in mm
Technical Data
Rated voltage & current†
UL
Voltage Ratings
AC 250 V, DC 65 V, 50/60 Hz
Current Ratings
0.05…16 A
CSA
VDE
AC 250 V, DC 65 V, 50/60 Hz
AC 250 V, DC 65 V, 50/60 Hz
0.05…16 A
0.05…16 A
Creepage resistance
Dielectric strength
Insulation resistance
Interrupting capacity
(VDE 0660, Part 101, P-2)
PTI 600 to IEC 112
4,000 VAC; IEC 664 & 664 A
> 100 MM (DC 500 V)
Interrupting capacity; 4201
(UL 1077/EN 60934 PC1)
4201-10
0.05…0.8 A
1…2 A
2.5…16 A
Rated current
Maximum capacity
Self-limiting
200 A
400 A
Rated voltage
Maximum capacity
0.05…2.0 A
2.0…16 A
20 A
AC 250 V
AC 250 V
AC 125 V
200 A
200 A
400 A
Typical life at 2 x rated current
Shock
Torque
5,000 operations
25 g (11 ms) to IEC 68-2-27, Test Ea
1.2 Nm
Vibration
Temperature range
5 g (57 to 500 Hz / ±0.38 mm, 10 to 57 Hz) to IEC 68-2-6, Test Fc
-30°C…+55°C (-22°F…+131°F)
Corrosion
Humidity
Weight
Wire size (UL)
96 hours at 5% salt spray, to IEC 68-2-11, Test Ka
240 hours at 95% RH, to IEC 68-2-3, Test Ca
60 g per pole
#20…8 AWG
solid/0.5…6 mm2
Accessories
Jumpers
Daisy Chain 50*
Straight CQB**
insulated
Angled CQB**
insulated
Adapter foot (for TS 32 Rail)
Busbar
Busbar end cap for 6720000227
Power lug for 6720000227
Dimensions in mm
Type
Part No.
BDC 50
9970290000
CQB
CQB
CQB
CQB
CQB
2
3
4
10
2
9970560000
9970570000
9970580000
9970590000
9970600000
CQB 3
CQB 4
CQB 10
MCBAF/TS 32
9970610000
9970620000
9970630000
9102100000
6720000227
6720000225
6720000226
WS 8/5 MC
DEK 5/5
DEK 5/5
1640750000***
0473460001
0473560001
Single pole 1 meter
Marking Tags
Note: Part numbers are shown
for a single card of pre-printed
tags numbered 1-50.
Special print only
Consecutive horizontal
Consecutive vertical
†Note: Resistive and inductive loads (0.05 - 16 A)
*BDC will accommodate 20 A per pin, 20 A total
**CQB will accommodate 18 A per pin, 18 A total; dedicated to 4201 Series
***Please specify horizontal or vertical print when ordering.
Standard quantity = 144 tags per card.
59
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
C B 2 2 0 0 S e r i e s S u p p l e m e n t a l C i rc u i t B re a k e r s
Circuit Breakers
Thermal Magnetic Type
CB2200 Series
Single Pole
CB2200 Series
Double Pole
CB2200 Series
Triple Pole
• Rated from 0.1 to 32.0 amps
• Available in single, double and triple
pole configurations
• Offers normally open (N/O) and normally
closed (N/C) auxiliary contacts
• Lever-switch trip/reset function
• Mounts on 32mm or 35mm DIN-rail
• UL 1077 recognized
• CSA C22.2 No. 235
Ordering Data
Type: Single Pole*
Type: Double Pole
Type: Triple Pole
Current Ratings
(amps)
0.1
N/O Aux.
Part No.
9911010005
Current Ratings
(amps)
0.1
N/O-N/C
Part No.
9912010003
Current Ratings
(amps)
0.1
N/O-N/C
Part No.
9913010003
0.2
0.3
0.4
9911020005
9911030005
9911040005
0.2
0.3
0.4
9912020003
9912030003
9912040003
0.2
0.3
0.4
9913020003
9913030003
9913040003
0.5
0.6
9911050005
9911060005
0.5
0.6
9912050003
9912060003
0.5
0.6
9913050003
9913060003
0.8
1.0
9911080005
9911100005
0.8
1.0
9912080003
9912100003
0.8
1.0
9913080003
9913100003
1.5
2.0
2.5
9911150005
9911200005
9911250005
1.5
2.0
2.5
9912150003
9912200003
9912250003
1.5
2.0
2.5
9913150003
9913200003
9913250003
3.0
4.0
5.0
6.0
8.0
10
12
9911300005
9911400005
9911500005
9911600005
9911800005
9921100005
9921120005
3.0
4.0
5.0
6.0
8.0
10
12
9912300003
9912400003
9912500003
9912600003
9912800003
9922100003
9922120003
3.0
4.0
5.0
6.0
8.0
10
12
9913300003
9913400003
9913500003
9913600003
9913800003
9923100003
9923120003
15
16
18
9921150005
9921160005
9921180005
15
16
18
9922150003
9922160003
9922180003
15
16
18
9923150003
9923160003
9923180003
20
9921200005
20
9922200003
20
9923200003
25
32
9921250005
9921320005
*All part numbers with N/O Auxiliary Contacts on each pole when the main breaker contact is open (in the OFF position)
Ordering Data
Type: Single Pole
Type: Double Pole
Type: Triple Pole
All part numbers with N/C Auxiliary Contacts on each pole when the main breaker contact is open (in the OFF position)
Current Ratings
Current Ratings
Current Ratings
(amps)
Part No.
(amps)
Part No.
(amps)
Part No.
0.1
9911010000
0.1
9912010000
0.1
9913010000
0.2
9911020000
0.2
9912020000
0.2
9913020000
0.3
9911030000
0.3
9912030000
0.3
9913030000
0.4
9911040000
0.4
9912040000
0.4
9913040000
0.5
9911050000
0.5
9912050000
0.5
9913050000
0.6
0.8
1.0
1.5
2.0
9911060000
9911080000
9911100000
9911150000
9911200000
0.6
0.8
1.0
1.5
2.0
9912060000
9912080000
9912100000
9912150000
9912200000
0.6
0.8
1.0
1.5
2.0
9913060000
9913080000
9913100000
9913150000
9913200000
2.5
9911250000
2.5
9912250000
2.5
9913250000
3.0
4.0
5.0
6.0
8.0
10
12
15
16
18
20
25
9911300000
9911400000
9911500000
9911600000
9911800000
9921100000
9921120000
9921150000
9921160000
9921180000
9921200000
9921250000
3.0
4.0
5.0
6.0
8.0
10
12
15
16
18
20
25
9912300000
9912400000
9912500000
9912600000
9912800000
9922100000
9922120000
9922150000
9922160000
9922180000
9922200000
9922250000
3.0
4.0
5.0
6.0
8.0
10
12
15
16
18
20
25
9913300000
9913400000
9913500000
9913600000
9913800000
9923100000
9923120000
9923150000
9923160000
9923180000
9923200000
9923250000
32
9921320000
32
9922320000
32
9923320000
60
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
C B 2 2 0 0 S e r i e s S u p p l e m e n t a l C i rc u i t B re a k e r s
CB2200 Series
Trip Curves—Thermal Magnetic Type
Typical time/current characteristics at 23ºC
CB2200 Series
F1
0.1 to 32 A
10,000
–30°C
+23°C
+55°C
Trip time in seconds
1,000
100
10
1
0.1
0.01
0.001
.8 1
3 4
2
6 8 10
20 30
50 70 100
…times rated current
-M1
0.1 to 7.5 A
10,000
–30°C
AC +23°C
DC +23°C
+55°C
Technical Data
UL
Voltage Ratings
277 / 480 VAC (50/60 Hz); 65 VDC
Current Ratings
0.1…32 A
CSA
VDE
277 / 480 VAC (50/60 Hz); 65 VDC
250 / 415 VAC / 65 VDC
0.1…32 A
0.1…32 A
Auxiliary contacts
Creepage resistance
Dielectric strength
250 VAC / 65 VDC, 1 A
PTI 600 to IEC 112
3,000 VAC; IEC 664 & 664 A
Insulation resistance
Interrupting capacity
(VDE 0660, Part 101, P-2)
> 100 MM (DC 500 V)
Rated current Rated voltage
0.05…0.8 A 250 / 415 VAC
6…32 A
250 / 415 VAC
Rupture capacity (3 times)
400 A
800 A
Interrupting capacity
(UL 1077/EN 60934 PC1)
Rated current
0.1…16 A
20…32 A
0.1…32 A
Max. rupture capacity (3 times)
5000 A
2000 A
2000 A
Rated voltage
277 / 480 VAC
277 / 480 VAC
65 VDC
Nm (lb. in.)
AC
.8 1
2
3 4
6 8 10
-M1
20 30
50 70 100
–30°C
AC +23°C
DC +23°C
+55°C
1,000
100
10
DC
0.1
AC
0.001
.8 1
0.6 (5.3)
Auxiliary contact: 0.5 (4.4)
5 g (57 to 500 Hz / ±0.38 mm, 10 to 57 Hz) to IEC 68-2-6, Test Fc
Part No.
9970290000
1 pole (CB2200)
2 pole (CB2200)
9986510000
9987360000
2
3 4
6 8 10
20 30
50 70 100
…times rated current
-T1
0.1 to 7.5 A
10,000
–30°C
+23°C
+55°C
1,000
Trip time in seconds
Type
BDC 50, 20 A maximum
8 to 32 A
10,000
0.01
96 hours at 5% salt spray, to IEC 68-2-11, Test Ka
240 hours at 95% RH, to IEC 68-2-3, Test Ca
Approximately 60 g per pole
max 6 mm2…8 AWG max 1.5 mm2…14 AWG (Aux. contact)
Daisy Chain 50
DC
…times rated current
-30…+60°C (-22°F…+140°F)
Accessories
Jumpers
Busbars
10
0.01
0.001
5,000 operations
25 g (11 ms) to IEC 68-2-27, Test Ea
Typical life at 2 x rated current
Shock
Torque
Vibration
Temperature range
Corrosion
Humidity
Weight
Wire size (UL)
10
0.1
Trip time in seconds
Rated voltage & current†
100
T
Dimensions in mm
Trip time in seconds
1,000
100
10
0.1
0.01
Marking Tags
1 2 3 4 5 6
Note: Part numbers shown are for a single
card of pre-printed tags numbered 1-50.
Special print only
Consecutive horizontal
Consecutive vertical
DEK 5/6
DEK 5/6
0490360000*
0468660001
DEK 5/6
0468760001
0.001
.8 1
2
3 4
6 8 10
20 30
50 70 100
…times rated current
-T1
8 to 32 A
10,000
†Note: Resistive and inductive loads (0.05 - 16 A)
*Please specify horizontal or vertical print when ordering.
–30°C
+23°C
+55°C
Trip time in seconds
1,000
100
10
1
0.1
0.01
0.001
.8 1
2
3 4
6 8 10
20 30
50 70 100
…times rated current
61
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
C B 9 1 0 0 S e r i e s S u p p l e m e n t a l C i rc u i t B re a k e r s
Circuit Breakers
Thermal Magnetic Type
CB9100 Series
Single Pole
CB9100 Series
Double Pole
CB9100 Series
Triple Pole
• Rated from 0.5 to 63 amps
• Available in single, double and triple
pole configurations
• Optional auxiliary contacts
• Mounts on 35mm DIN-rail
• UL and CSA approvals
• CSA 277 VAC (1 pole) or
480 VAC (2 and 3 pole)
• 50 VDC (0.5 A to 50 A) 1 pole
• 110 VDC (0.5 A to 50 A) 2 pole
Ordering Data
Type: Single Pole
Current Ratings
(amps)
0.5
1.0
2.0
3.0
4.0
6.0
10.0
13.0
16
20
25
32
40
50
63
Type: Double Pole
Part No.
Current Ratings
(amps)
9925350000
9925360000
0.5
1.0
9925380000
9925390000
9925400000
9925410000
Type: Triple Pole
Part No.
Current Ratings
(amps)
Part No.
9925650000
9925660000
0.5
1.0
9925810000
9925820000
2.0
9925680000
2.0
9925840000
3.0
4.0
6.0
9925690000
9925700000
9925710000
3.0
4.0
6.0
9925850000
9925860000
9925870000
9925430000
10.0
9925730000
10.0
9925890000
9929820000
9925440000
13.0
16
9929830000
9925740000
13.0
16
9929840000
9925900000
9925450000
9925460000
20
25
9925750000
9925760000
20
25
9925910000
9925920000
9925470000
9925480000
9925490000
32
40
50
9925770000
9925780000
9925790000
32
40
50
9925930000
9925940000
9925950000
9925500000
63
9925800000
63
9925960000
Trip Curves
Thermal Magnetic Type
Typical time/current characteristics at 23°C
CB9100 Series
M1
0.5 to 6 A
10,000
M1
AC 10 to 40 A
10,000
M1
10,000
23°C
23°C
23°C
100
100
100
1
Trip time in seconds
1,000
Trip time in seconds
1,000
Trip time in seconds
1,000
10
10
1
10
1
0.1
0.1
0.1
0.01
0.01
0.01
0.001
0.8 1
2
3
4
6
8 10
20 30
… times rated current
50 70 100
AC 63 A
0.001
0.8 1
2
3
4
6
8 10
20 30
… times rated current
50 70 100
0.001
0.8 1
2
3
4
6
8 10
20 30
50 70 100
… times rated current
62
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
C B 9 1 0 0 S e r i e s S u p p l e m e n t a l C i rc u i t B re a k e r s
CB9100 Series
70
45
54
44
36
18
59
1 pole
2 pole
6
3 pole
86
Dimensions in mm
Internal Wiring Diagram
Auxiliary Contact Modules
Technical Data
Rated voltage & current
UL 1077
277 V (1 pole)
480 V (2 and 3 pole)
50 VDC (1 pole)
110 VDC (2 pole)
CSA C 22.2 No. 235
277 V (1 pole)
480 V (2 and 3 pole)
50 VDC (1 pole)
110 VDC (2 pole)
91.4
VDE
80.6
Creepage resistance
PTI 250 to IEC 112
Insulation resistance
Interrupting capacity
(UL 1077/EN 609334 PC1) 1 pole
>100 MM at 500 VDC
Current ratings
0.5...63 A
Mechanical/Electrical endurance
Shock
0.5...32 A
0.5...63 A
0.5...50 A
20,000/10,000
20 g (10 ms)
Torque
2 Nm
Vibration
Temperature range - operating
3 g (10 to 55 Hz)
-25°C...+55°C (-13°F to 131°F)
Weight
Strip length
Auxiliary contact rating
Wire size - #22…12 AWG
1 pole (130 g); 2 pole (280 g); 3 pole (430 g)
12 mm
Voltage
AC 220/240
5.8
Interrupting Rupture capacity (3X)
10,000 A (UL)
Voltage
277 VAC/50 VDC
2,000 A (UL)
6,000 A (UL)
6,000 A (UL)
277 / 480 AC
50 VDC (1) pole
110 VDC (2) poles
45.2
Current
5A
Type
Accessories
Jumpers
9
Current
Side/Middle
Part No.
3 pole bus, 10 x 1010 mm, buses (19) 3 phase groupings
3 pole bus, 16 x 210 mm, buses (4) 3 phase groupings
80A/100A
120A/130A
9970330000
9970340000
3 pole bus, 16 x 1010 mm, buses (19) 3 phase groupings
1 pole bus, 12 x 210 mm, buses 12 breakers
120A/130A
80A/100A
9970350000
9970360000
1 pole bus, 12 x 210 mm (insulated), buses 12 breakers
Bus bar clamp
5
69
AC 277
3A
DC 24 V
4A
DC 60 V
1A
DC220 V
0.4 A
#18…2 AWG (line); #18…3 AWG (load)
Wire size
44
44
63A
130A
Internal Auxiliary Wiring Diagram
9991990000
9970370000
14 12 11
Auxiliary contacts
SPDT
Security hardware
Auxiliary contacts
9970300000
Lock out cover
9970380000
ETO 10/26, yellow (26 mm x 10 mm)
1686401687
Marking Tags
Adhesive label
63
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
I n t ro d u c t i o n — M C Z O v e r v o l t a g e P ro t e c t i o n
Slim overvoltage protection terminals for
instrumentation and control engineering
Weidmuller MCZ ovp overvoltage protection terminals are
characterized by their high level of protection concentrated in
a compact space of 6 mm. The tension clamp connection
and direct grounding via the terminal rail contact results in timesavings during installation. The MCZ ovp terminals are suitable
for installing in the narrowest of places in automated process,
industrial and building services systems.
The different models
MCZ ovp CL is a three-stage protective combination with
a suppression diode between the current paths. It limits the
overvoltage in analog signal circuits, e.g. current loops.
MCZ ovp SL is a three-stage protective combination with two
suppression diodes, each from the signal line to ground. It limits
the overvoltage in binary circuits, e.g. for actuators.
MCZ ovp CL FG is a three-stage protective combination with
a suppression diode between the current paths. It limits the
overvoltage in analog signal circuits. A high-resistance ground
connection is achieved with a gas discharge tube.
MCZ ovp SL FG is a three-stage protective combination with
two suppression diodes, each from the signal line to ground.
It limits the overvoltage in binary circuits, e.g. for actuators.
A high-resistance ground connection is achieved with three
gas discharge tubes.
MCZ ovp filter terminals contain selected varistors,
capacitors and series inductances. They form reliable noise
filters. Coupled interference in the kHz range is safely
discharged to ground. For example, the signal inputs of a PLC,
which can be protected against interference voltages and RF
interference.
The three-stage overvoltage protection terminals are fitted with
gas discharge tubes, varistors, suppression diodes (TAZ) and
decoupling inductors. Individual protective components such as
varistors and suppression diodes complement the range.
EMC regulations require the terminal rail to be securely screwed
to a grounded mounting plate. Optimum protection is achieved
when the PE contact is made via a tension clamp terminal
every 600 mm.
Derating curve MCZ ovp filter
loading current in A
The MCZ ovp overvoltage protection terminals are available with
rated voltages of 24, 48, 115 and 230 V. The ground contact is
produced by clipping the terminal to a grounded terminal rail. To
guarantee a safe energy discharge of up to 10 kA (8/20 μs) via
these terminals, the TS 35 DIN rail must therefore be grounded.
mounted on rail
without clearance
mounted on rail
with clearance 20 mm
ambient temperature in °C
Derating curve MCZ ovp filter
Derating curve MCZ ovp filter
loading current in A
derating curve 1,25 A
mounted on rail
without clearance
mounted on rail
with clearance 20 mm
ambient temperature in °C
64
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
M C Z O v e r v o l t a g e P ro t e c t i o n
3- or 1-stage protection with
tension clamp connection
MCZ OVP CL 24 V DC 0.5 A
Protection for current loops
MCZ OVP CL 24 V AC 0.5 A
Protection for current loops
• Slimline overvoltage protection terminal
with tension clamp connection
• 6 mm Slimline fine overvoltage protection
• fast wiring thanks to TS contact and
tension clamp connections
• can be cross-connected using ZQV
1
4
1
4
U
5
5
TS
TS
U
IN
Ordering data
2
3
2
Type
3
OUT
Qty.
10
Part No.
Type
Version
MCZ OVP CL 24VDC 0.5A
Technical data
Rated voltage (AC)
Rated voltage (DC)
24 V
24 V
28 V
max. continuous voltage, Uc
Operating current, Imax
Volume resistivity
28 V
0.50 A
2.50 Ω
38 V
0.50 A
1.00 Ω
Gas discharge tube
Varistor
yes
yes
yes
yes
Suppression diodes
Cut-off frequency (-3 dB) at load impedance
Discharge current, max. (8/20 μs)
Protection level on output side sym., input 1 kV/μs, typ.
Protection level on output side sym., input 8/20 μs, typ.
Protection level on output side unsym., input 1kV/μs, typ.
Protection level on output side unsym., input 8/20 μs, typ.
yes
500.0 kHz 240 Ω
2.5 kA
40 V
65 V
40 V
65 V
yes
500.0 kHz 240 Ω
2.5 kA
45 V
70 V
45 V
70 V
Design
Type of connection
terminal
tension clamp connection
terminal
tension clamp connection
Storage temperature, min./max.
Operating temperature, min./max.
-25 °C/85 °C
-25 °C/60 °C
-25 °C/85 °C
-25 °C/60 °C
CE; UL listed
CE; UL listed
tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 63.5
tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 63.5
Note: see derating curve
Note: see derating curve
8448920000
MCZ OVP CL 24VAC 0.5A
Qty.
10
Part No.
8472880000
Approvals
Dimensions
Clamping range (rating- / min. / max.)
Length x width x height
Accessories
End plate
mm2
mm
AP MCZ 1.5
8389030000
AP MCZ 1.5
8389030000
65
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
M C Z O v e r v o l t a g e P ro t e c t i o n
3- or 1-stage protection with
tension clamp connection
MCZ OVP CL 24 V UC 1.25 A
Protection for current loops
MCZ OVP SL 24 V DC 0.5 A
Protection for binary signals
• Slimline overvoltage protection terminal
with tension clamp connection
• 6 mm Slimline fine overvoltage protection
• fast wiring thanks to TS contact and
tension clamp connections
• can be cross-connected using ZQV
1
4
1
4
5
5
TS
TS
2
3
Qty.
10
Part No.
8448960000
2
Ordering data
Version
Type
MCZ OVP CL 24VUC 1.25A
Type
MCZ OVP SL 24VDC 0.5A
Technical data
Rated voltage (AC)
24 V
Rated voltage (DC)
max. continuous voltage, Uc
Operating current, Imax
24 V
27 V
1.25 A
24 V d
28 V
0.50 A
Volume resistivity
Gas discharge tube
Varistor
Suppression diodes
1.00 Ω
yes
yes
yes
2.50 Ω
yes
yes
yes
Cut-off frequency (-3 dB) at load impedance
Discharge current, max. (8/20 μs)
Protection level on output side sym., input 1 kV/μs, typ.
Protection level on output side sym., input 8/20 μs, typ.
Protection level on output side unsym., input 1kV/μs, typ.
Protection level on output side unsym., input 8/20 μs, typ.
Design
Type of connection
Storage temperature, min./max.
Operating temperature, min./max.
500.0 kHz 240 Ω
2.5 kA
80 V
130 V
40 V
65 V
terminal
tension clamp connection
-25 °C/85 °C
-25 °C/60 °C
500.0 kHz 240 Ω
2.5 kA
80 V
130 V
40 V
65 V
terminal
tension clamp connection
-25 °C/85 °C
-25 °C/60 °C
CE; UL listed
CE; UL listed
tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 63.5
tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 63.5
Note: see derating curve
Note: see derating curve
3
Qty.
10
Part No.
8448940000
Approvals
Dimensions
Clamping range (rating- / min. / max.)
Length x width x height
Accessories
End plate
mm2
mm
AP MCZ 1.5
8389030000
AP MCZ 1.5
66
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
8389030000
M C Z O v e r v o l t a g e P ro t e c t i o n
3- or 1-stage protection with
tension clamp connection
MCZ OVP SL 24 V UC 1.25 A
Protection for binary signals
MCZ OVP CL 48 V UC 0.5 A
Protection for current loops
• Slimline overvoltage protection terminal
with tension clamp connection
• 6 mm Slimline fine overvoltage protection
• fast wiring thanks to TS contact and
tension clamp connections
• can be cross-connected using ZQV
1
4
1
5
4
5
TS
TS
2
2
3
Ordering data
Version
Type
MCZ OVP SL 24VUC 1.25A
Qty.
10
Part No.
8448970000
Type
MCZ OVP CL 48VUC 0.5A
Technical data
Rated voltage (AC)
24 V
48 V
Rated voltage (DC)
max. continuous voltage, Uc
Operating current, Imax
24 V
28 V
1.25
48 V
53 V
0.50 A
Volume resistivity
Gas discharge tube
Varistor
Suppression diodes
1.00 Ω
yes
yes
yes
2.50 Ω
yes
yes
yes
Cut-off frequency (-3 dB) at load impedance
Discharge current, max. (8/20 μs)
Protection level on output side sym., input 1 kV/μs, typ.
Protection level on output side sym., input 8/20 μs, typ.
Protection level on output side unsym., input 1kV/μs, typ.
Protection level on output side unsym., input 8/20 μs, typ.
Design
Type of connection
Storage temperature, min./max.
Operating temperature, min./max.
500.0 kHZ 240 Ω
2.5 kA
80 V
130 V
40 V
65 V
terminal
tension clamp connection
-25 °C/85 °C
-25 °C/60 °C
500.0 kHz 240 Ω
2.5 kA
80 V
150 V
80 V
150 V
terminal
tension clamp connection
-25 °C/85 °C
-25 °C/60 °C
CE; UL listed
CE; UL listed
tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 63.5
tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 63.5
Note: see derating curve
Note: see derating curve
3
Qty.
10
Part No.
8449000000
Approvals
Dimensions
Clamping range (rating- / min. / max.)
Length x width x height
Accessories
End plate
mm2
mm
AP MCZ 1.5
8389030000
AP MCZ 1.5
8389030000
67
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
M C Z O v e r v o l t a g e P ro t e c t i o n
3- or 1-stage protection with
tension clamp connection
MCZ OVP SL 48 V UC 0.5 A
Protection for binary signals
MCZ OVP CL 48 V UC 1.25 A
Protection for current loops
• Slimline overvoltage protection terminal
with tension clamp connection
• 6 mm Slimline fine overvoltage protection
• fast wiring thanks to TS contact and
tension clamp connections
• can be cross-connected using ZQV
1
1
4
4
5
5
TS
TS
2
2
3
Ordering data
Version
Type
MCZ OVP SL 48VUC 0.5A
Qty.
10
Part No.
8449030000
Type
MCZ OVP CL 48VUC 1.25A
Technical data
Rated voltage (AC)
48 V
48 V
Rated voltage (DC)
max. continuous voltage, Uc
Operating current, Imax
48 V
53 V
0.50
48 V
53 V
1.25 A
Volume resistivity
Gas discharge tube
Varistor
Suppression diodes
2.50 Ω
yes
yes
yes
1.00 Ω
yes
yes
yes
Cut-off frequency (-3 dB) at load impedance
Discharge current, max. (8/20 μs)
Protection level on output side sym., input 1 kV/μs, typ.
Protection level on output side sym., input 8/20 μs, typ.
Protection level on output side unsym., input 1kV/μs, typ.
Protection level on output side unsym., input 8/20 μs, typ.
Design
Type of connection
Storage temperature, min./max.
Operating temperature, min./max.
500.0 kHz 240 Ω
2.5 kA
160 V
300 V
80 V
150 V
terminal
tension clamp connection
-25 °C/85 °C
-25 °C/60 °C
500.0 kHz 240 Ω
2.5 kA
80 V
150 V
80 V
150 V
terminal
tension clamp connection
-25 °C/85 °C
-25 °C/60 °C
CE; UL listed
CE; UL listed
tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 63.5
tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 63.5
Note: see derating curve
Note: see derating curve
3
Qty.
10
Part No.
8449040000
Approvals
Dimensions
Clamping range (rating- / min. / max.)
Length x width x height
Accessories
End plate
mm2
mm
AP MCZ 1.5
8389030000
AP MCZ 1.5
68
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
8389030000
M C Z O v e r v o l t a g e P ro t e c t i o n
3- or 1-stage protection with
tension clamp connection
MCZ OVP SL 48 V UC 1.25 A
Protection for binary signals
MCZ OVP CL 115 V UC 1.25 A
Protection for current loops
• Slimline overvoltage protection terminal
with tension clamp connection
• 6 mm Slimline fine overvoltage protection
• fast wiring thanks to TS contact and
tension clamp connections
• can be cross-connected using ZQV
1
4
1
4
5
5
TS
TS
2
3
Qty.
10
Part No.
8449050000
2
Ordering data
Version
Type
MCZ OVP SL 48VUC 1.25A
Type
MCZ OVP CL 115VUC 1.25A
Technical data
Rated voltage (AC)
48 V
115 V
Rated voltage (DC)
max. continuous voltage, Uc
Operating current, Imax
48 V
53 V
1.25
115 V
127 V
1.25 A
Volume resistivity
Gas discharge tube
Varistor
Suppression diodes
1.00 Ω
yes
yes
yes
1.00 Ω
yes
yes
yes
Cut-off frequency (-3 dB) at load impedance
Discharge current, max. (8/20 μs)
Protection level on output side sym., input 1 kV/μs, typ.
Protection level on output side sym., input 8/20 μs, typ.
Protection level on output side unsym., input 1kV/μs, typ.
Protection level on output side unsym., input 8/20 μs, typ.
Design
Type of connection
Storage temperature, min./max.
Operating temperature, min./max.
500.0 kHZ 240 Ω
2.5 kA
160 V
300 V
80 V
150 V
terminal
tension clamp connection
-25 °C/85 °C
-25 °C/60 °C
500.0 kHz 240 Ω
2.5 kA
220 V
360 V
220 V
360 V
terminal
tension clamp connection
-25 °C/85 °C
-25 °C/60 °C
CE; UL listed
CE; UL listed
tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 63.5
tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 63.5
Note: see derating curve
Note: see derating curve
3
Qty.
10
Part No.
8449060000
Approvals
Dimensions
Clamping range (rating- / min. / max.)
Length x width x height
Accessories
End plate
mm2
mm
AP MCZ 1.5
8389030000
AP MCZ 1.5
8389030000
69
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
M C Z O v e r v o l t a g e P ro t e c t i o n
3- or 1-stage protection with
tension clamp connection
MCZ OVP SL 115 V UC 1.25 A
Protection for binary signals
MCZ OVP CL 230 V UC 1.25 A
Protection for current loops
• Slimline overvoltage protection terminal
with tension clamp connection
• 6 mm Slimline fine overvoltage protection
• fast wiring thanks to TS contact and
tension clamp connections
• can be cross-connected using ZQV
1
4
5
1
4
5
TS
TS
2
3
3
OUT
2
IN
Ordering data
Version
Type
MCZ OVP SL 115VUC 1.25A
Qty.
10
Part No.
8449070000
Type
MCZ OVP CL 230VUC 1.25A
Technical data
Rated voltage (AC)
115 V
230 V
Rated voltage (DC)
max. continuous voltage, Uc
Operating current, Imax
115 V
127 V
1.25 A
230 V
250 V
1.25 A
Volume resistivity
Gas discharge tube
Varistor
Suppression diodes
1.00 Ω
yes
yes
yes
1.00 Ω
yes
yes
yes
Cut-off frequency (-3 dB) at load impedance
Discharge current, max. (8/20 μs)
Protection level on output side sym., input 1 kV/μs, typ.
Protection level on output side sym., input 8/20 μs, typ.
Protection level on output side unsym., input 1kV/μs, typ.
Protection level on output side unsym., input 8/20 μs, typ.
Design
Type of connection
Storage temperature, min./max.
Operating temperature, min./max.
500.0 kHz 240 Ω
2.5 kA
440 V
720 V
220 V
360 V
terminal
tension clamp connection
-25 °C/85 °C
-25 °C/60 °C
500.0 kHz 240 Ω
2.5 kA
420 V
710 V
420 V
710 V
terminal
tension clamp connection
-25 °C/85 °C
-25 °C/60 °C
CE; UL listed
CE; UL listed
tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 63.5
tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 63.5
Note: see derating curve
Note: see derating curve
Qty.
10
Part No.
8449080000
Approvals
Dimensions
Clamping range (rating- / min. / max.)
Length x width x height
Accessories
End plate
mm2
mm
AP MCZ 1.5
8389030000
AP MCZ 1.5
70
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
8389030000
M C Z O v e r v o l t a g e P ro t e c t i o n
3- or 1-stage protection with
tension clamp connection
MCZ SL FG 24 V AC 0.5 A
not grounded
MCZ CL FG 24 V AC 0.5 A
not grounded
• Slimline overvoltage protection terminal
with tension clamp connection
• 6 mm Slimline fine overvoltage protection
• fast wiring thanks to TS contact and
tension clamp connections
• can be cross-connected using ZQV
Ordering data
Version
Type
MCZ OVP SL FG 24VAC 0.5A
Qty.
10
Part No.
8823280000
Type
MCZ OVP CL FG 24VUC 0.5A
Technical data
Rated voltage (AC)
24 V
24 V
Rated voltage (DC)
max. continuous voltage, Uc
Operating current, Imax
24 V
28 V
0.50 A
24 V
28 V
0.50 A
Volume resistivity
Gas discharge tube
Varistor
Suppression diodes
1.00 Ω
90 V / 10 kA
30 V
2.50 Ω
90 V / 10 kA
30 V
Cut-off frequency (-3 dB) at load impedance
Discharge current, max. (8/20 μs)
Protection level on output side sym., input 1 kV/μs, typ.
Protection level on output side sym., input 8/20 μs, typ.
Protection level on output side unsym., input 1kV/μs, typ.
Protection level on output side unsym., input 8/20 μs, typ.
Design
Type of connection
Storage temperature, min./max.
Operating temperature, min./max.
500.0 kHz / 240 Ω
2.5 kA
40 V
65 V
40 V
65 V
terminal
tension clamp connection
-25 °C/85 °C
-25 °C/60 °C
500.0 kHz / 240 Ω
2.5 kA
40 V
65 V
40 V
65 V
terminal
tension clamp connection
-25 °C/85 °C
-25 °C/60 °C
CE; UL listed
CE; UL listed
tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 63.5
tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 63.5
Note: see derating curve
Note: see derating curve
Qty.
25
Part No.
8704240000
Approvals
Dimensions
Clamping range (rating- / min. / max.)
Length x width x height
Accessories
End plate
mm2
mm
AP MCZ 1.5
8389030000
AP MCZ 1.5
8389030000
71
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
M C Z O v e r v o l t a g e P ro t e c t i o n
3- or 1-stage protection with
tension clamp connection
MCZ OVP SL 230 V UC 1.25 A
Protection for binary signals
MCZ OVP 24 V 0.5 A
Filter
• Slimline overvoltage protection terminal
with tension clamp connection
• 6 mm Slimline fine overvoltage protection
• fast wiring thanks to TS contact and
tension clamp connections
• can be cross-connected using ZQV
1
4
4
5
5
TS
TS
3
OUT
2
IN
Ordering data
1
Type
Qty.
10
Part No.
IN
Type
Version
MCZ OVP SL 230VUC 1.25A
Technical data
Rated voltage (AC)
Rated voltage (DC)
230 V
230 V
24 V
24 V
max. continuous voltage, Uc
Operating current, Imax
Volume resistivity
Gas discharge tube
Varistor
250 V
1.25 A
1.00 Ω
yes
yes
26 V
0.50 A
1.50
no
yes
Suppression diodes
Cut-off frequency (-3 dB) at load impedance
Discharge current, max. (8/20 μs)
Protection level on output side sym., input 1 kV/μs, typ.
Protection level on output side sym., input 8/20 μs, typ.
yes
500.0 kHz 240 Ω
2.5 kA
840 V
1420 V
no
50.0 kHz 50 Ω
0.5 kA
140 V
190 V
Protection level on output side unsym., input 1kV/μs, typ.
Protection level on output side unsym., input 8/20 μs, typ.
Design
Type of connection
Storage temperature, min./max.
420 V
710 V
terminal
tension clamp connection
-25 °C/85 °C
70 V
100 V
terminal
tension clamp connection
-25 °C/85 °C
Operating temperature, min./max.
-25 °C/60 °C
-25 °C/60 °C
CE; UL listed
CE; UL listed
tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 63.5
tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 63.5
Note: see derating curve
Note: see derating curve
8449090000
3
OUT
2
MCZ OVP FILTER 24V 0.5A
Qty.
10
Part No.
8449100000
Approvals
Dimensions
Clamping range (rating- / min. / max.)
Length x width x height
Accessories
End plate
mm2
mm
AP MCZ 1.5
8389030000
AP MCZ 1.5
72
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
8389030000
M C Z O v e r v o l t a g e P ro t e c t i o n
3- or 1-stage protection with
tension clamp connection
MCZ OVP 90 V
Gas discharge tube
MCZ OVP S10K30
Varistor S10K30
• Slimline overvoltage protection terminal
with tension clamp connection
• 6 mm Slimline fine overvoltage protection
• fast wiring thanks to TS contact and
tension clamp connections
• can be cross-connected using ZQV
1
4
1
4
5
5
TS
TS
2
IN
3
OUT
Part No.
8449130000
2
3
OUT
IN
Ordering data
Version
Type
Qty.
MCZ OVP gas charge eliminator, 90 V 10
Type
MCZ OVP VARISTOR S10K30
Technical data
Rated voltage (AC)
50 V
24 V
Rated voltage (DC)
max. continuous voltage, Uc
Operating current, Imax
70 V
72 V
16.00 A
24 V
30 V
16.00 A
Volume resistivity
Gas discharge tube
Varistor
Suppression diodes
0.20 Ω
90 V / 10 kA
no
no
0.20 Ω
no
yes
no
Cut-off frequency (-3 dB) at load impedance
Discharge current, max. (8/20 μs)
Protection level on output side sym., input 1 kV/μs, typ.
Protection level on output side sym., input 8/20 μs, typ.
Protection level on output side unsym., input 1kV/μs, typ.
Protection level on output side unsym., input 8/20 μs, typ.
Design
Type of connection
Storage temperature, min./max.
Operating temperature, min./max.
2.5 kA
700 V
800 V
700 V
800 V
terminal
tension clamp connection
-25 °C/85 °C
-25 °C/60 °C
125
45 V
55 V
45 V
55 V
terminal
tension clamp connection
-25 °C/85 °C
-25 °C/60 °C
CE; UL listed
CE; UL listed
tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 63.5
tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 63.5
Note: see derating curve
Note: see derating curve
Qty.
10
Part No.
8449140000
Approvals
Dimensions
Clamping range (rating- / min. / max.)
Length x width x height
Accessories
End plate
mm2
mm
AP MCZ 1.5
8389030000
AP MCZ 1.5
8389030000
73
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
M C Z O v e r v o l t a g e P ro t e c t i o n
3- or 1-stage protection with
tension clamp connection
MCZ OVP TAZ 24 V DC
Diode unipolar
MCZ OVP TAZ 24 V UC
Diode bipolar
• Slimline overvoltage protection terminal
with tension clamp connection
• 6 mm Slimline fine overvoltage protection
• fast wiring thanks to TS contact and
tension clamp connections
• can be cross-connected using ZQV
1
4
4
5
5
TS
TS
2
3
OUT
IN
Ordering data
Version
1
Type
MCZ OVP TAZ DIODE 24VDC
Qty.
10
Part No.
8449150000
Technical data
Rated voltage (AC)
3
OUT
2
IN
Type
MCZ OVP TAZ DIODE 24VUC
Qty.
10
Part No.
8449160000
24 V
Rated voltage (DC)
max. continuous voltage, Uc
Operating current, Imax
24
30
16.00 A
27 V
27 V
16.00 A
Volume resistivity
Gas discharge tube
Varistor
Suppression diodes
0.20 Ω
no
no
yes
0.20 Ω
no
no
yes
Cut-off frequency (-3 dB) at load impedance
Discharge current, max. (8/20 μs)
Protection level on output side sym., input 1 kV/μs, typ.
Protection level on output side sym., input 8/20 μs, typ.
Protection level on output side unsym., input 1kV/μs, typ.
Protection level on output side unsym., input 8/20 μs, typ.
Design
Type of connection
Storage temperature, min./max.
Operating temperature, min./max.
112
55 V
65 V
55 V
65 V
terminal
tension clamp connection
-25 °C/85 °C
-25 °C/60 °C
0.5 kA
55 V
65 V
110 V
130 V
terminal
tension clamp connection
-25 °C/85 °C
-25 °C/60 °C
CE; UL listed
CE; UL listed
tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 63.5
tension clamp connection
1.5 / 0.5 / 1.5
91 x 6 x 63.5
Note: see derating curve
Note: see derating curve
Approvals
Dimensions
Clamping range (rating- / min. / max.)
Length x width x height
Accessories
End plate
mm2
mm
AP MCZ 1.5
8389030000
AP MCZ 1.5
74
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
8389030000
I n t ro d u c t i o n — S u r g e P ro t e c t i o n D e v i c e s
SD Series
SLP Series
Data and Signal Protection
The SD Series are ultra-slim user-friendly devices for protecting
electronic equipment and systems against surges on signal
and I/O cabling, and the SLP Series provides 20kA power surge
protection for process control, equipment systems and
distribution panels.
Product Features:
• Range of ATEX Certified intrinsically safe surge protectors
• Ultra-slim and space saving designs; easy installation
• Multistage hybrid protection circuitry - 10kA maximum surge
current for SD Series, and 20kA maximum surge current for
SLP Series
• Range of voltage ratings ideal for process I/O applications
• Designed for high bandwidth, low resistance applications;
RTD, Public Switch Telephone Network (PSTN) and 3-wire
transmitter versions available in SD Series
MA15 Series
AC & DC Power Protection
The MA15 Series of surge protection devices protects
electronic equipment and computer networks against the
effects of noise pollution induced in power supplies. MA15
units filter out and suppress the effects of industrial noise
and surges caused by lightning, switching devices, thyristor
controls, transmission system overloads and power-factor
correction circuits.
• Surge protection for two loops or one 4-wire circuit per
SLP Series module
• 10 year product warranty
The SD and SLP Series surge protection devices provide
unparalleled packing densities, application versatility, proven
and reliable hybrid circuitry, simple installation and optional ‘loop
disconnect’ facilities (SD Series). These features make the SD and
SLP Series the ultimate surge protection solutions for process
control equipment, I/O systems and communications networks.
Product Features:
• 18kA surge protection and RFI filtering
TP48 Series
• Protects panel loads up to 15 Amps in series,
unlimited Amps in parallel
Transmitter and Sensor Protection
• Suitable for AC or DC application
• Thermal and short circuit protection
• LED status indication feature
• 10 year product warranty
The TP48 Series of transmitter protectors safeguards electronic
process transmitters against induced surges and transients from
field cabling. They uniquely provide a level of protection for 2, 3
and 4 wire field-mounted transmitters that greatly exceeds the
optional transient protection facilities available from the transmitter
manufacturers without any additional wiring, conduit modifications
or other expensive extras.
Product Features:
• Easy and direct mounting – simply screw into spare
conduit entry
• Intrinsically safe; flameproof to CENELEC standards; ATEX
approved
• Parallel connection avoids introduction of resistance into loop
75
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
I n t ro d u c t i o n — S u r g e P ro t e c t i o n D e v i c e s
SD Series
SLP Series
The exceptionally high packing densities are the result of an
ultra slim footprint for individual modules, which can double-up
as feedback terminals. Each module provides full hybrid surge
protection for 2 and 3-wire loop protection.
The multi-stage hybrid surge protection network at the heart of
the SLP uses a combination of solid state electronics and a gas
filled discharge tube (GDT) to provide surge protection up to
20kA. This impressive surge protection circuit is designed to
exhibit exceptionally low line resistance and adds only a minimal
voltage drop to the circuit.
Modules with a comprehensive range of voltage ratings cover all
process related signals such as RTDs, Thermo- couples (THCs),
4 - 20mA loops, telemetry outstations, shut-down systems and
fire and gas detectors.
The optional loop disconnect featured on the SD07, SD16,
SD32 and SD55 modules allows users to perform commissioning
and maintenance without removing the surge protection device. In
addition, a third connection on the field and safe side of the
module is provided for safe termination of shields.
For three wire applications the specially designed SDRTD
(Resistance Temperature Detector) and the SD32T3, (for separately
powered 4 - 20mA loops) provide full 3-wire protection in a single
compact unit. The SD07R3 provides protection of 3-wire pressure
transducers on low power circuits.
For higher bandwidth applications, the SDR Series meets the
demands of today’s highest speed communication systems.
The SLP device does not adversely affect the performance or
operation of the loop or combined equipment during operation.
The device allows signals to pass with very little attenuation,
while diverting surge currents safely to the ground and clamping
output voltages to safe levels.
Fully automatic in operation, SLP devices react immediately to
ensure that equipment is never exposed to damaging surges
between lines or the lines and ground. Reacting instantly, the SLP
redirects surges safely to the ground and resets automatically.
The versatile SLP series provides full hybrid surge protection,
combining protection for two process loops into
one case.
For higher bandwidth applications, the SLP series has been
developed to meet the demands of today’s highest speed
communication systems.
120V and 240V AC versions are available for I/O and power
supplies up to three Amps of load current.
Publc Switched telephone networks can be protected by
the SDPSTN.
All modules are DIN-rail mountable on a TS-35 rail. A comprehensive range of mounting and grounding accessories are
available.
76
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
S u r g e P ro t e c t i o n D e v i c e s — S D S e r i e s
SD Series Guide to applications and selection
The SD Series of signal protection devices includes models for
a full range of applications operating at voltages up to 250V ac.
The optional fuse/disconnect package provides both fused
protection against fault currents and a convenient method of
isolating field circuitry from protected circuitry without requiring
additional disconnect terminals. The standard fuse (replaceable)
is rated 250mA. 50mA fuses are available by special request.
Solid links can be used in applications where only the
disconnect feature is required.
This feature is important in applications where a signal protection
device is used with a bulk power supply feeding multiple loops.
The individual fuse module prevents a fault or follow on
current on one loop disrupting the power supply to the
others. In addition, loops can be removed from the circuit for
maintenance or added without requiring additional disconnect
terminals.
The following guide provides application information for the
SD series. For technical information, see page 84.
PROTECTED CIRCUIT
FIELD CIRCUIT
Analog inputs (high-level)
Bulk
PSU
2-wire transmitters, 4-20mA, conventional and smart
SD32 and SD55 are recommended for use with conventional
and smart 4-20mA transmitters (fed by a well-regulated supply),
the choice dependent upon the maximum working voltage of the
system (32V and 55V respectively). The diagram illustrates an
application using the fuse/disconnect. Both models are available
in ‘X’ versions without the optional fuse/disconnect feature.
1 Up to 50V dc
4/20mA
1 to 5V
2
4
TP48
transmitter
protector
5
6
3
SD32
SD55
SD32X
SD55X
(no fuse)
Multiple
Loops
2-wire transmitters
Analog inputs (low-level)
SDRTD
RTDs, Thermocouples (THCs) and mV sources
using the SDRTD.
1
4
5
For optimum accuracy, the energizing current should be chosen
to ensure the voltage across the RTD does not exceed 1V over
the full measurement range. When using a PT100 device, an
energizing current of 1mA is recommended.
Recorder
Controller
Computer
etc.
2
6
3
SDRTD
3-wire RTDs
2xSD07X
or 2xSD16X
Photocells and turbine flowmeters
Depending upon the operational voltage, the SD07 or SD16 are
the preferred choices for this application. SD07X and SD16X are
also suitable.
1
4
Photocell
Thermocouple (THC)
Signal
5
mV source
2
Turbine
Flowmeter
6
3
SD07
SD16
SD07X
SD16X
(no fuse)
photocells,
thermocouples (THCs),
mV sources and
turbine flowmeters
77
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
S u r g e P ro t e c t i o n D e v i c e s — S D S e r i e s
Analog outputs
PROTECTED CIRCUIT
FIELD CIRCUIT
Controller outputs (I/P converters)
2xSD15X, SD32X
Dependent on the working voltage, recommendations
include the SD16, SD32 and SD55, and the equivalent
‘X’ versions.
1
4
P
V
I
5
2
6
OV
3
SD16
SD32
SD35
SD16
SD32X
SD55X
(no fuse)
Controller outputs
(I/P converters)
Digital (on/off) inputs - Switches
SD
Suitable signal protection devices include the SD07, SD16,
SD32 and SD55 modules, and the equivalent “X” versions. The
choice is dependent upon the operating voltage of the system.
1
4
5
V
2
6
Logic Signal
3
SD07
SD16
SD32
SD55
SD07X
SD16X
SD32X
SD55X
OV
(no fuse)
Switches
Digital (on/off) outputs Alarms, LEDs, solenoid valves, etc.
SD32X
1
4
LED
Alarm
5
The SD32 or SD32X are the recommended choice for
this application.
32V max
2
6
3
SD32
SD32X
(no fuse)
Alarms, LEDs, solenoid
values, etc.
4
Incoming
Telephone
Line
Telemetry Public Switch Telephone Network
(PSTN) - Telemetry outstations
1
5
Modem,
fax or
telephone
2
6
3
The SDPSTN has been designed specifically for the protection
of signals transmitted on public switched telephone networks.
Telecom line
AC supplied equipment - PLC, I/O systems
4
110/120V ac
or
220/240V ac
The recommended choice or systems on 110-120V ac is the
SD150X ; for 220-240V ac systems, the SD275X is
recommended.
5
PLC,
DCS,
SCADA,
etc.
2
6
3
PLC, I/O systems
78
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
Final output from
1
www.barr-thorp.com
S u r g e P ro t e c t i o n D e v i c e s — S D S e r i e s
Transmitter and sensor protection
Transmitters and sensors are widely used in highly exposed areas and where lightning damage is common. In many cases, the ideal
solution for 2-wire transmitters or sensors is the TP48, which mounts directly onto the transmitter via spare conduit entries or a tee
fitting. Where these entries are not available or 3-wire devices are used, the compact design and simple installation of the SD Series
makes it an ideal choice for transmitter protection.
The SDs within the junction box should be installed as close as possible to the sensor or transmitter they are protecting, but no
further than one meter away. A bond is required from the general mass of steelwork to the sensor or transmitter housing, using either
a flat short braid or a cable at least 0.16 inch2 (4mm2) cross sectional area. In most instances, this bond is made automatically by
fixing the metallic transmitter housing to the plant structure and ensures the voltage difference between the signal conductors and
the transmitter housing is below the transmitter’s insulation rating. Please note that the transmitters or sensors are connected to the
SD protected equipment terminals, not the field cables.
2-wire transmitters or sensors
TO HOST CIRCUIT
SD PROTECTED FIELD CIRCUIT
4-20mA transmitters - conventional and smart
The SD16X, SD32X and SD55X are an excellent alternative if the
TP48 is not an acceptable solution, either because of technical
suitability or mounting difficulties.
1
4
4-20mA
2
5
6
3
Plant structure
SD16X
SD32X
SD55X
SPD DIN rail
2-wire transmitter or sensor
3-wire transmitters or sensors
Vibration Sensors and 4-20mA loop process control systems
generally require three wire connections when powered from an
external source. This may be accomplished in one unit by using
the SD32T3 3- terminal Surge Protection Device (SPD). Because
the SD32T3 protects all three conductors within the same unit,
higher protection is achieved because the SPD hybrid circuitry is
common to all three wires.
4
1
2
Plant structure
24V
5
3
4-20mA
6
Common OV
SD32T3
The SD07R3, SD16R3, SD32R3 and SD55R3 are also suitable
for the protection of 3-wire pressure transducers on low power
circuits.
SPD DIN rail
3-wire transmitter or sensor
1
4-wire transmitters or sensors Flow meters, level detectors, etc.
4-wire systems such as level detectors require two SDs, one
for the supply and the other for the transmitter output. Generally
the voltages across the pairs are similar, so the recommended
choice is a pair of SD16X, SD32X or SD55Xs. Dependent upon
the supply voltage, AC powered transmitters should be
protected with an SD150X for the supply inputs.
4
4-20mA
2
5
6
3
1
4
Supply voltage
Plant structure
2
5
Supply OV
6
3
SD16X
SD32X
SD55X
SPD DIN rail
4-wire transmitter or sensor
79
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
S u r g e P ro t e c t i o n D e v i c e s — S D S e r i e s
Communication systems protection
High-speed data links between buildings or one part of a plant to another have become more common with the widespread use of
smart transmitters and the increase in remote installations. The SD Series has an SPD suitable for all process I/O applications with
a choice of low resistance units, high bandwidth and a variety of voltage ranges. Featuring an extremely high bandwidth, the SDR
Series is designed to meet the requirements for high speed data links.
Communication systems
RS232, RS422, RS485
SD PROTECTED HOST CIRCUIT
TP PROTECTED
FIELD CIRCUIT
The recommended choice for these applications is the SD16R
or SD32R depending on the maximum driver signal.
4
TP48
1
5
2
6
3
RS232, RS422, RS485
SD PROTECTED HOST CIRCUIT
PROTECTED FIELD CIRCUIT
Bus powered systems
4
1
There are a variety of bus powered systems specially designed
for the process industry. The ideal surge protection device for
these systems is the SD32R, with a very high bandwidth and
modest in-line resistance.
4
5
2
6
3
1
5
2
6
SD32R
(no fuse)
3
SD32R
(no fuse)
TP48
4
5
6
1
2
3
SD32R
(no fuse)
Bus powered systems
Table 1
Typical Applications
Table 1 shows suitable SD devices for different applications. In
some applications alternative devices may be used, for example,
where lower in-line resistance or a higher voltage power supply
is used.
MTL Surge Technologies has operationally tested the recommended SD Series units with the representative highways listed.
However, no formal approval for their use in these systems has
been sought from the respective bodies.
Application
Allen Bradley Data Highway Plus
Preferred Part No.
Alternate Part No.
SD16R
Foundation Fieldbus
31.25kbits/s voltage mode
SD32R
1.0/2.5 Mbits/s
SD55R
HART
SD32X
SD32, SD32R
Honeywell DE
SD32X
SD32, SD32R
LonWorks
FFT-10
SD32R
LPT-10
SD55R
TP-78
SD07R
IS78†
SD32R
Modbus & Modbus Plus (RS485)
SD16R
PROFIBUS
DP
PA (IEC 1158, 31.25 kbits/s)
SD32R
SD32R
RS232
SD16
RS422
SD07R
RS423
SD07R
RS485
SD07R
WorldRP (IEC 1158)
SD32R
31.25 kbits/s voltage mode
1.0/2.5 Mbits/s
SD55R
80
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
SD16X
S u r g e P ro t e c t i o n D e v i c e s — S D S e r i e s
Hazardous area applications
Zone0/Zone1
The dangers from lightning induced sparking in Zone 0 are
considered real enough to require preventative measures. IEC
60079-14 (1996-12) Electrical apparatus for explosive gas
atmospheres Part 14: Electrical installations in hazardous areas
(other than mines) stresses the importance of SPDs in hazardous
areas. An outdoor installation where there is a high likelihood of
both lightning induced transients and combustible gases
requires the installation of SPDs to prevent possible ignition of
the gases. Areas seen particularly at risk include flammable liquid
storage tanks, effluent treatment plants, distillation columns in
petrochemical works and gas pipelines.
SPDs for transmitter protection should be installed in Zone 1,
sufficiently close to the Zone 0 boundary to prevent high
voltages entering Zone 0. The distance from the SPD to Zone 0
should be less than 36” where possible. In practice the SPD
would normally be mounted on the transmitter or sensor housing
which usually lies in Zone 1 and is very close to Zone 0. Because
there is only a very small free volume, the SD series is suitable for
mounting in flameproof or explosion proof enclosures.
Zone 2
The SD series is suitable for protecting electrical circuits in Division
2, Zone 2 and can be used without affecting the safety aspects of
the circuit. Non-incendive (low-current) circuits can be protected
using any SD series unit mounted in either the safe or hazardous
area, including those with the fuse disconnects facility. Non-arcing
(high current) circuits can also be protected, however SPDs with
the fuse disconnect facility may only be mounted in the safe area.
For use in these circuits the units must be mounted in a suitable
enclosure. In most cases the minimum requirements are IP54 and
7Nm resistance to impact. The SD series is self certified by MTL
Surge Technologies as suitable for this purpose.
The certification parameters for the SD**R, SD**R3
and SDRTD are:
EEx ia IIC T4, Li = 0
li = 260mA for Ui up to 60V
The power rating for each of the above is dependent on the table
shown below.
Pi = 1W (–30°C to +75°C)
Pi = 1.2W (–30°C to +60°C)
Pi = 1.3W (–30°C to +40°C)
The SD** series are classified as simple apparatus and are
intended for use in Zone 2 or safe areas only, because their fuses
are not fully encapsulated.
Installation
Positioning
The SDs should be mounted on the field wiring side to ensure
that any surges entering from the field do not damage any
intrinsically safe barriers or galvanic isolators in the system.
The SDs and intrinisically safe interface should be mounted
close to each other but on separate DIN-rails in order to maintain
the required 1.97” (50mm) clearance between safe area and
hazardous area terminals of the IS interface.
SD series DIN rail
IS barrier DIN rail
Instrument
Field cables
Instrument earth
Substation ground mat
Certification
Introducing surge protection into Intrinsically Safe (IS)
circuits is trouble free as long as the current and power
parameters are not exceeded. In the SD series, the SD**X,
SD**R, SD**R3, SDRTD and SD**T3 all have ATEX certification
for use in IS circuits located in Zones 0, 1 or 2. The certification
parameters for the SD**X and SD**T3 are:
EEx ia IIC T4, Li = 0.22mH
li
li
li
li
=
=
=
=
260mA for Ui up to 20V
175mA for Ui up to 26V
140mA for Ui up to 28V
65mA for Ui up to 60V
Grounding
The recommended grounding for field-mounted devices has
been illustrated previously. The grounding at the control panel
is more critical as there are usually a number of grounding
systems, each with their own requirements.The grounding
system illustrated here replaces the instrument 0V bond, the
control system PSU bond and the IS ground with one single
ground connection to meet all the design requirements and
give the most effective protection against the effects of lightning
induced surges.
Marshalling cabinet
System Connection Cable
SPD
Isolated instrument rail
Isolated instrument rail
Electrical earth
Frame
connection
Floor void
System earth
To plant/neutral
star point
In all installations utilizing safety related apparatus, consideration
should be given to protecting the system supply and any long
communication cable.
81
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
S u r g e P ro t e c t i o n D e v i c e s — S D S e r i e s
Protection
Full hybrid line to line
Each line to screen/ground
Max. discharge surge current (Imax) (8/20µs)
10kA (8/20μs)
6.5kA (SD150X and SD275X only)
Max. discharge surge current (isn)
3kA (8/20μs)
Lightning impulse current (Iimp) (10/350µs)
2.5kA
1.0kA (SD150X and SD275X only)
Response time
<1ns
RTD resistance range (SDRTD)
10 to 1500Ω
Degradation accuracy (SDRTD at 1mA)
0.1% (RTD resistance > 100)
0.1W (RTD resistance < 100)
Ambient temperature
–40°C to +80°C - working (-40°F to 176°F)
–40°C to +80°C - storage (-40°F to 176°F)
Humidity
5 to 95% RH (non-condensing)
Category tested
A2, B2, C1, C2, C3
Overstressed fault mode In=3kA
12kA
9kA (SD150X and SD275X only)
Impulse durability (8/20µs)
10kA
6.5kA (SD150X and SD275X only)
Terminals
2.5mm2 (12 AWG)
Mounting
T-section DIN-rail 35 x 7.5 or 35 x 15mm rail
(1.38” x 0.3” x 0.6”)
Weight
70g approximately (2.5oz)
Case flammability
UL94 V-2
AC durability
1Arms, 5T
Service conditions
80kPa - 160kPa
5% - 95% RH
EMC compliance
To Generic Immunity Standards,
EN 50082, part 2 for industrial
environments
R&TTE compliance
EN 50082-2 : 1995
EN 41003 : 1999
EN 60950 : 1992
(not applicable to SD150X and SD275X)
LVD compliance
SD150X & SD275X
EN 60950 : 1992
EN 61010 : 1995
SDPSTN
EN 41003 : 1999
IEC compliance
EN 61643-21:2001
Approvals
Standard
Certificate/File No.
Approved for
Product
Canada, USA
(CSA/C/US)
Country (Authority)
CSA C22.2 No. 0-M1991
CSA C22.2 No. 157-M1992
UL 913, 5th edition
CSA C22.2 No. 142-M1987
CSA C22.2 No. 213-M1987
UL 508, 17th edition
UL 1604, 3rd edition
LR 103652-3
EEx ia Class 1,
Groups A, B
C and D, T4
Class 1, Div 2
Groups A,B,C, D T4
SD07,SD16,SD32,SD55,
SD07X,SD16X,SD32X,
SD55X,SD07R,SD16R,
SD32R,SD55R,SDRDT,
SD32T3,SD07R3,SD16R3,
SD32R3,SD55R3
USA
(UL)
UL 497B Listed
E220693
Isolated loop
communication
circuits
SD07,SD16,SD32,SD55
SD07X,SD16X,SD32X
SD55X,SD07R,SD16R
SD32R,SD55R,SD07R3
SD16R3,SD32R3,SD55R3
SD32T3,SD55T3,
SD07X3,SD16X3,SD32X3,
SD55X3,SDRTD
USA, Canada
(UL)
UL 1449
Recognized Component
E217523
AC power
protection
SD150X,SD275X
0.28”
+0.02”
-0.0”
+0.4mm
-0.0mm
4
7.0mm
1
5
2
6
3
4.03” (102.1mm)
0.28” rail (7mm)
4.32” (109.6mm)
0.6” rail (16mm)
All figures typical at 77°F (25°C)
unless otherwise stated
3.99”
(101.3mm)
Specifications SD Series
3.9”
(99mm)
Ordering Data
Technical Data
Nominal voltage+(Un) Vdc
Nominal voltage+(Un) Vac
Nominal current (In) mA
Series resistance W/line
Max. leakage current μA
Rated voltage (MCOV) Uc
Voltage protection level (Up)
@1kV/μs V
Residual voltage @ isn V
Bandwidth frequency fG
Special feature
Ordering Data
Technical Data
Nominal voltage+(Un) Vdc
Nominal voltage+(Un) Vac
Nominal current (In) mA
Series resistance W/line
Max. leakage current μA
Rated voltage (MCOV) Uc
Voltage protection level (Up)
@1kV/μs V
Residual voltage @ isn V
Bandwidth frequency fG
Special feature
Part No.
SD07
Part No.
SD16
Part No.
SD32
Part No.
SD55
7
5
250
4.2
500
7.7
<12
16
11
250
4.2
5
17
<25
32
22
250
4.2
5
36
<45
55
38
250
4.2
5
62
<90
30
25
fuse disconnect
40
25
fuse disconnect
60
25
fuse disconnect
100
25
fuse disconnect
Part No.
SD07R
Part No.
SD16R
Part No.
SD32R
Part No.
SD55R
7
5
400
2.7
500
7.7
<12
16
11
400
4.7
5
17
<25
32
22
400
10
5
36
<45
55
38
400
10
5
62
<90
30
50
high Bandwidth
40
50
high Bandwidth
60
50
high Bandwidth
100
50
high Bandwidth
82
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
S u r g e P ro t e c t i o n D e v i c e s — S D S e r i e s
Ordering Data
Technical Data
Nominal voltage+(Un) Vdc
Nominal voltage+(Un) Vac
Nominal current (In) mA
Series resistance W/line
Max. leakage current μA
Rated voltage (MCOV) Uc
Voltage protection level (Up)
@1kV/μs V
Residual voltage @ isn V
Bandwidth frequency fG
Special feature
Ordering Data
Technical Data
Nominal voltage+(Un) Vdc
Nominal voltage+(Un) Vac
Nominal current (In) mA
Series resistance W/line
Max. leakage current μA
Rated voltage (MCOV) Uc
Voltage protection level (Up)
@1kV/μs V
Residual voltage @ isn V
Bandwidth frequency fG
Special feature
Ordering Data
Technical Data
Nominal voltage+(Un) Vdc
Nominal voltage+(Un) Vac
Nominal current (In) mA
Series resistance W/line
Max. leakage current μA
Rated voltage (MCOV) Uc
Voltage protection level (Up)
@1kV/μs V
Residual voltage @ isn V
Bandwidth frequency fG
Special feature
Part No.
SD07X
Part No.
SD16X
Part No.
SD32X
Part No.
SD55X
7
5
400
2.2
500
7.7
<12
16
11
400
2.2
5
17
<25
32
22
400
2.2
5
36
<45
55
38
400
2.2
5
62
<90
30
25
low resistance
40
25
low resistance
60
25
low resistance
100
25
low resistance
Part No.
SD32T3
Part No.
SD07R3
Part No.
SD16R3
Part No.
SD32R3
Part No.
SD55R3
32
22
400
2.2
5
36
<45
7
5
400
2.7
500
7.7
<12
16
11
400
4.7
5
17
<25
32
22
400
10
5
36
<45
55
38
400
10
5
62
<90
60
720
3 terminal
30
50
3 terminal
40
50
3 terminal
60
50
3 terminal
100
50
3 terminal
Part No.
SDRTD
Part No.
SDPSTN
Part No.
SD150X
Part No.
SD275X
1
0.75
>10
2.7
0.3
5
<12
162
114
550
4.7
5
175
<200
170
120
3A
0.1
250 ac rms; 170 ac
130 ac rms
<400
339
240
3A
0.1
250 ac rms; 350 ac
275 ac rms
<700
30
50
3-wire RTD
235
4
PSNT
450
high current
850
high current
Mounting Accessories
0494920000 Rail Holder
Grounding/Ground Rail Accessories
1010100000 Ground terminal, DIN rail mounted
Accessories (Replacement)
SDF25
Replacement fuse pack 250mA standard
Preferred
Alternate
Application
Part No.
Part No.
Application
Allen Bradley Data Highway Plus
Foundation Fieldbus
31.25kbits/s voltage mode
1.0/2.5 Mbits/s
HART
Honeywell DE
LonWorks
FFT-10
LPT-10
TP-78
IS78†
Modbus & Modbus Plus (RS485)
SD16R
SD32, SD32R
SD32, SD32R
PROFIBUS
DP
PA (IEC 1158, 31.25 kbits/s)
RS232
RS422
RS423
RS485
WorldRP (IEC 1158)
31.25 kbits/s voltage mode
1.0/2.5 Mbits/s
SD32R
SD55R
SD32X
SD32X
SD32R
SD55R
SD07R
SD32R
SD16R
Preferred
Alternate
Part No.
Part No.
SD32R
SD32R
SD16
SD07R
SD07R
SD07R
SD32R
SD16X
SD55R
83
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
S u r g e P ro t e c t i o n D e v i c e s — S L P S e r i e s
Specifications SLP Series
Approvals
All figures typical at 77°F (25°C)
unless otherwise stated
Standard
Certificate/File No.
Approved for
Product
ATEX
BS EN 60950:1992
BS EN 61000-6-2:1999
BS EN 61010-1:1993
ATEX0377X
EEx N IIC T4
SLP07D, SLP16D,
SLP32D
USA (FM)
Class Nos. 3600 (1998),
3610 (1999),
3611 (1999), 3615
(1989), 3810 incl.
Supp 1 (1995-07 (1989-03),
ANSI/NEMA 250 (1991),
ISA-S12.0.01 (1999)
3011208
Intrinsically Safe:
I/1/A-D, I/O/II C
Non incendive: I/2/A-D,
I/2/II C
SLP07D, SLP16D,
SLP32D
Canada (FM)
C22.2 No. 213, 142, 94,
157, 30
ANSI/NEMA 250
CAN/CSA-E79-0
CAN/CSA-E79-11
3025374
IS/I/1/ABCD
I/0/Ex ia/IIC
I/0/Ex ib/IIC
NE/I/2/ABCD
NE/I/2/IIC
SLP07D, SLP16D,
SLP32D
Maximum surge current
20kA (8/20μs waveform) per line
Leakage Current
<1mA @ working voltage
Maximum rated load current
1.50A
Loop resistance
2 Ohm
Capacitance
Line - Line - 60pF
Bandwidth
-0.1db @9kHz - 37MHz
-3dB @50MHz
Response time
<1ns
Ambient temperature
–40°C to +80°C (working)
–40°F to +176°F (working)
–40°C to +80°C (storage)
–40°F to +176°F (storage)
Humidity
5 to 95% RH (non-condensing)
Country (Authority)
Terminals
2.5mm2 (12 AWG)
Electrical connections
Plug/header screw terminal strip
Mounting
T-section DIN-rail (35 x 15mm rail)
Weight
5oz (140g approximately)
Case flammability
UL94-V0
EMC compliance
BS EN 60950:1992
BS EN 61000-6-2:1999
BS EN 61010-1:1993
Dimensions
Connections
Ordering Data
Technical Data
Nominal voltage Un
Rated voltage (MCOV) Uc
Nominal current In
Nominal discharge current (8/20μs) isn
Max discharge current (8/20μs) Imax
Lightning impulse current (10/350μs) Iimp
Residual voltage @ isn Up
Voltage protection level @ 1kV/μs Up
Bandwidth fG
Capitance C
Series resistance R
Operating Temperature Range
Category tested
Overstressed fault mode in=3kA
Impulse durability (8/20μs)
Degree of protection
AC durability
Service conditions
Part No.
SLP07D
Part No.
SLP16D
Part No.
SLP32D
7V
8V
1.50A
3kA
20kA
2.5kA
10V
<8V
50MHz
60pF
1.0
-40°C to +80°C
A2, B2, C1, C2, C3, D1
22kA
10kA
IP20
1Arms, 5T
80kPa - 160kPa
5% - 95% RH
16V
18V
1.50A
3kA
20kA
2.5kA
23V
<18V
50MHz
60pF
1.0
-40°C to +80°C
A2, B2, C1, C2, C3, D1
22kA
10kA
IP20
1Arms, 5T
80kPa - 160kPa
5% - 95% RH
24V
32V
1.50A
3kA
20kA
2.5kA
40V
<38V
50MHz
60pF
1.0
-40°C to +80°C
A2, B2, C1, C2, C3, D1
22kA
10kA
IP20
1Arms, 5T
80kPa - 160kPa
5% - 95% RH
Installation
84
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
S u r g e P ro t e c t i o n D e v i c e s — M A 1 5 S e r i e s
Specifications MA15 Series
MA15 Series
Although industrial computers and PLCs
are designed to be rugged, the extra
protection provided by the DIN-rail
mounting MA15 units is critical. Ideally
suited for protecting panel mounted
equipment and typically used in the
controls section of a motor control center
(MCC), the MA15 range provides surge
and RFI protected power.
With a unique ‘three-stage’ combination of
protection elements, these units suppress
conducted RFI and voltage surges. The
circuit elements are: (1) surge clipping
components to absorb transient surges
that may otherwise damage equipment,
(2) a filter to suppress noise in the system
and, (3) ring suppression. Ring suppression
prevents surges causing the filter to ‘ring’
(oscillate) under low load conditions – an
effect that actually accentuates interference
in most commercially available filters.
Suitable for AC or DC application, MA15
units reduce both electromagnetic
emissions and the susceptibility of the
associated equipment to emissions from
other sources. MA15 devices also offer
installation flexibility. To protect circuits
rated 15A or less, MA15 devices should
be installed in series. To protect higher
current circuits, simply install the MA15
in parallel.
LED status indication is standard with
the MA15 units. Thermal fusing is also
incorporated into each 18kA rated device
as an additional safety feature. MA15
modules also offer short circuit protection
for added safety.
Dimensions
Maximum surge current: 18kA (8/20 μs) per mode
Maximum leakage current: <0.3mA
Maximum continuous operating current
15A series connection
Unlimited Amps in parallel
Maximum continuous operating voltage
25% above nominal
Limiting voltage
Let through voltage
@ 500A ring
120V/140V versions
295V
240V/280V versions
356V
@ 500A 8/20 µs
120V/140V versions
320V
240V/280V versions
800V
@ 3kA 8/20 µs
120V/140V versions
396V
240V/280V versions
975V
@ 10kA 8/20 µs
120V/140V versions
585V
240V/280V versions
1210V
Maximum attenuation (typical): -55dB @ 100MHz
Modes protected: L-N, L-G, N-G
Ambient temperature limits
–40°F to +185°F (working)
–40°C to +85°C (working)
Humidity
95% RH (non-condensing)
Casing
Polymide-PA, with G- or T-section
(Top-hat) DIN-rail mounting foot
Connectors
Screw terminal
Terminals
0.1 inch2 (2.5mm2 ) 12 AWG
Installation
Mounting
G- or T-section (‘Top-hat’) or
1.4 inch (35mm) DIN rail
Weight
3.53oz (100g)
EMC compliance
BS EN 60950 : 1992
BS EN 61000-6-2 : 1999
LED Indication
Green LED on Protection present
Green LED off Internal failure
All figures typical at 77°F (25°C) unless otherwise stated
Ordering Data
Part No.
MA15D1SI
MA15D2SI
AC
120V, 47-63Hz
240V, 47-63Hz
DC
140V
280V
The grounding of the surge protector and the protected
equipment is very important and, if possible, should be
accomplished as illustrated.
Please note that the unit is marked Line and Load and
it is important that the unit is installed with the Line
side connected to the incoming power and the Load
connected to the equipment to be protected. For
parallel application however, the Line side is connected
to the incoming power and the Load left unconnected.
Approvals
Standard
Approved for
Product No.
United States
Canada
Country (Authority)
UL 1449
Recognized Component
AC Power Product
MA15D1SI,
MA15D2SI
United States
Canada
UL 1449
Recognized Component
UL 1604
Hazardous Locations
Class I, Division 2
Groups A, B, C and D
MA15D1SI,
MA15D2SI
{
85
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
S u r g e P ro t e c t i o n D e v i c e s — T P 4 8 S e r i e s
The TP Series protection network
consists of high-power, solid-state
electronics and a gas-filled discharge
tube capable of diverting 10kA impulses.
The whole unit is encased in an ANSI
316 stainless steel housing, threaded
for the common conduit entries used
on process transmitters. Versions are
available for 1/2” NPT, 20mm ISO, and
G1/2” (BSP 1/2 inch) threaded entries.
Approvals
Country (Authority)
Atex Directive
94/9/EC
USA (FM)
Specifications TP Series
All figures typical at 77°F (25°C)
unless otherwise stated
Maximum surge current
10kA peak current (8/20μs waveform)
Leakage current
Less than 10μA at maximum working voltage
Working voltage
48 VDC maximum
Bandwidth
1MHz
Resistance
No resistance introduced into loop
Ambient temperature limits
-20°C to +80°C (working)
-40°C to +80°C (storage)
Humidity
5% to 95% RH (non-condensing)
Electrical connections
TP48
3 flying leads (line1, line 2 & ground)
TP48 3 Wire
4 flying leads (+ve, -ve, signal & ground)
TP48 4 Wire
5 flying leads (+ve, -ve, signal +ve, signal -ve, ground)
Wire size 32/0.2 (1.0mm2, 18 AWG)
Lead length 250mm (minimum)
Casing
ANSI 316 stainless steel hexagonal barstock,
male thread
Threads
TP48-3-N & TP48-4-N
1/2” NPT
TP48-3-I & TP48-4-1
20mm ISO (M20 x 1.5)
TP48-3-G & TP48-4-G
G 1/2” (BSP 1/2”)
Weight
175g (6.2oz)
Dimensions
See Figure 1
EMC compliance
To Generic Immunity Standards EN50082, part 2
for industrial environments
Electrical safety
EEx ia IIC T4, Ceq=O, Leq=0; the unit can be connected
without further certification into any intrinsically safe loop
with open circuit voltage <60V and input power <1.2W.
EEx d IIC T4; the unit is apparatus-approved to flame
proof (explosionproof) standards, and can be fitted into
a similarly approved housing.
Canada (FM)
Global
Standard
BS EN 50021:1999
Certificate/File No.
TML02ATEX0032X
Class Nos. 3600
(1998), 3610 (1999),
3611 (1999), 3615
(1989), 3810 incl.
Supp 1 (1995-07
(1989-03),
ANSI/NEMA 250
(1991),
ISA-S12.0.01 (1999)
C22.2 No. 157
C22.2 No. 213
C22.2 No 142
C22.2 No. 94
C22.2 No. 30
3022293
IEC 60079-0:2004
IEC 60079-11:2006
3025374
IECEx BAS 07.0045X
Approved for
Ex n II T6 (-40°C<Tamb<+60°C)
EEx n II T5 (-40°C<Tamb<+85°C)
Intrinsically Safe:
I, II, III/1/A-G, I/0/IIC
Explosionproof: I/1/A-D
Non incendive: I/2/A-D, I/2/IIC
Dust ignition proof: II,III/1/EFG
Special protection: II/2/FG
Intrinsically Safe:
I, II, II/1/A-G, I/O/IIC
Explosionproof: I/1/A-D
Nonincendive: I/2/A-D, I/2/IIC
Dust ignition proof: II, III/1/EFG
Special protection: II/2/FG
Ex ia IIC T4/T5/T6
Ex tD A20 IP6X T85°C/T100°C/
T135°C
Product
TP48-X-Y-Z
TP48-X-Y-Z
TP48-X-Y-Z
TP48-X-Y-NDI
IEC 61241-0:2004
IEC 61241-1:2004
Key: X = 3 or 4 or blank, Y = N, I or G, Z = NDI
Ordering Data
Part No.
TP48NNDI
TP48INDI
TP48GNDI
TP483NNDI
TP483INDI
TP483GNDI
TP484NNDI
TP484INDI
TP484GNDI
Dimensions
1/2” NPT thread
20mm ISO thread
G 1/2” (BSP 1/2 inch)
1/2” NPT thread
20mm ISO thread
G 1/2” - BSP 1/2 inch
1/2” NPT thread
20mm ISO thread
G 1/2” - BSP 1/2 inch
Figure 1
The TP units are designed for mounting
directly into an unused conduit entry on a
process transmitter housing. Generally, two
such entries are provided, one of which is
used for the loop wiring. On the unused
entry, the blanking plug or other closure
device is removed and an appropriately
threaded TP screwed into its place. The
transmitter specification should provide
information indicating the required thread
type. TP units can be installed using thread
adaptors if necessary, including certified
adaptors in hazardous area applications.
For applications where two conduit entries
are not provided or where both are used
for electrical connections, TP units can be
housed in conventional conduit hub or
junction boxes, provided access to the
loop terminals is possible. Figure 2 shows
connection details for 3 & 4 wire process
transmitter.
Figure 2
Certified
Certified
Certified
Certified
Certified
Certified
Certified
Certified
Certified
SPD
SPD
SPD
SPD
SPD
SPD
SPD
SPD
SPD
-
2.95”
(75mm)
1.07”
(27mm)
0.91”
(23mm)
2.17”
(55mm)
Dimensions across flats 0.91” (23mm)
Installation
86
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
Lead length
9.85” (250mm)
minimum
DIN-Rail Receptacles
These modules are intended for use within
cabinets and enclosures as 120 VAC
outlets for power tools, lights, computers
or test equipment for troubleshooting.
5 Amp Simplex
w/Circuit Breaker
15 Amp Simplex
w/o Circuit Breaker
• Compact and easily snaps onto
35mm DIN-rail
• CSA, UL508A and cULus approved
• Available with ground fault current
interrupt (GFCI) or standard simplex
and duplex outlets
• Option for visual indication of power
included with GFCI versions
• Enclosed versions feature NEMA
rated enclosure with UL94 VO flammability rating
Schematic diagram
Schematic diagram
Technical data
Input voltage
Voltage
1120 VAC
120 VAC
Current
Wire Size (AWG)
Stripping Length mm/in.
Terminal Torque
Mounting
Width
Length
5A max.
26 - 12 AWG (0.14 - 4.0mm2)
6mm
0.5-0.6 Nm
TS32 or TS35 DIN-Rail
35mm/1.38 in.
70mm/2.76 in.
15A max.
26 - 12 AWG (0.14 - 4.0mm2)
6mm
0.5-0.6 Nm
TS32 or TS35 DIN-Rail
35mm/1.38 in.
70mm/2.76 in.
58.5mm/2.30 in.
58.5mm/2.30 in.
Height
Ordering data
Type
Part No.
Type
Single outlet with circuit breaker
9915480001
(supplemental protector with manual reset via push button)
Single outlet without circuit breaker
r LR-229352, v E252394
r LR-229352, v E252394
Part No.
9915480000
Approvals
Trip Curves
87
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
DIN-Rail Receptacles
Dimensional Drawing
15 Amp Duplex
15 Amp GFCI
120 VAC nominal, 125 VAC max.
15A max.
50 - 60 Hz
Withstands 2000V per UL498
10 kA
2 kA
N/A
20 - 10 AWG (solid or stranded, copper only)
0.79Nm/7 lb.-in.
Screw terminals, slotted
120 VAC nominal, 125 VAC max.
15A max.
50 - 60 Hz
Withstands 1500V per UL498
10 kA
10 kA
5mA ±1mA
20 - 10 AWG (solid or stranded, copper only)
0.79Nm/7 lb.-in.
Screw terminals, slotted
-25°C to 60°C
-35°C to 80°C
-25°C to 60°C
-35°C to 80°C
PBT/polycarbonate blend, UL94 rating V0 @ .63mm
Polyamide 6/6 30% GF, UL94 rating V0 @ .63mm
Stainless Steel
TS35 DIN-Rail or direct panel mount
74.1mm/2.9 in.
123.6mm/4.9 in.
61.5mm/2.4 in.
PBT/polycarbonate blend, UL94 rating V0 @ .63mm
Polyamide 6/6 30% GF, UL94 rating V0 @ .63mm
Stainless Steel
TS35 DIN-Rail or direct panel mount
74.1mm/2.9 in.
123.6mm/4.9 in.
61.5mm/2.4 in.
Type
DRAC DP 15
Type
DRAC GF 15
Technical data
Voltage
Current
Operating Frequency
Dielectric Voltage
Short-Circuit Current Rating (SCCR)
Current Interrupting
Trip Level
Termination Wire Size
Terminal Torque
Terminations
Temperature:
Operating
Storage
Material Listing
Enclosure Cover, Flammibility
Enclosure Base, Flammibility
Spring
Mounting
Width
Length
Height
Ordering data
Part No.
6720005421
Approvals/Certifications
Enclosure Type
Description
cULus Listed to UL508A and C22.2 No. 14
File E223801
NEMA WD6, 5-15R
Description
cULus Listed to UL508A and C22.2 No. 14
File E223801
NEMA WD6, 5-15R
88
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
Part No.
6720005422
DIN-Rail Receptacles
15 Amp Duplex w/LED
Dimensional Drawing
This new DIN-rail mountable duplex
receptacle makes adding a 120V maintenance AC outlet to control cabinets quick
and easy. It mounts on standard 35mm
DIN-rail and requires just 42mm of rail
space. An LED indicates that 120V is
applied to the module. The terminations
accept slotted or Phillips screwdrivers.
The mounting foot includes a latching
lock – slide it open, mount the module on
the DIN-rail and slide the lock closed.
• requires just 42mm of DIN-rail
• includes power status LED
• latching mounting foot makes installation
and removal from DIN-rail easy
• CSA certified and cURus recognized
Technical data
Voltage
Current
Wire Size (AWG)
Stripping Length mm/in.
Terminations
Terminal Torque
Mounting
Width
Length
Height
120 VAC nominal
15A max.
14-12 AWG (Solid or stranded, copper only)
8.8-11 / 0.347-0.433
Screw terminals, slotted or Phillips
“L”:line “W”:neutral “G”:ground
0.5Nm/4.4 in-lb
TS35 DIN-Rail
42mm/1.65 in.
99mm/3.90 in.
51mm/2.01 in.
Ordering data
Type
DUPLEX 120VAC OUTLET W/LED
Part No.
6720005430
Approvals/Certifications
Description
CSA certified, file 251163, Project 2345434, according to
C22.2 No. 42
cURus recognized, file E340886, according to UL498 and
C22.2 No. 182.3
89
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
DIN-Rail Receptacles
Dimensional Drawing
20 Amp Duplex
20 Amp GFCI
Technical data
Voltage
Current
Operating Frequency
Dielectric Voltage
Short-Circuit Current Rating (SCCR)
Current Interrupting
Trip Level
Termination Wire Size
Terminal Torque
Terminations
Temperature:
Operating
Storage
Material Listing
Enclosure Cover, Flammibility
Enclosure Base, Flammibility
Spring
Mounting
Width
Length
Height
120 VAC nominal, 125 VAC max.
20A max.
50 - 60 Hz
Withstands 2000V per UL498
120 VAC nominal, 125 VAC max.
20A max.
50 - 60 Hz
Withstands 1500V per UL498
10 kA
2 kA
N/A
20 - 10 AWG (solid or stranded, copper only)
0.79Nm/7 lb.-in.
Screw terminals, slotted
10 kA
10 kA
5mA ±1mA
20 - 10 AWG (solid or stranded, copper only)
0.79Nm/7 lb.-in.
Screw terminals, slotted
-25°C to 60°C
-35°C to 80°C
-25°C to 60°C
-35°C to 80°C
PBT/polycarbonate blend, UL94 rating V0 @ .63mm
Polyamide 6/6 30% GF, UL94 rating V0 @ .63mm
Stainless Steel
TS35 DIN-Rail or direct panel mount
74.1mm/2.9 in.
123.6mm/4.9 in.
61.5mm/2.4 in.
PBT/polycarbonate blend, UL94 rating V0 @ .63mm
Polyamide 6/6 30% GF, UL94 rating V0 @ .63mm
Stainless Steel
TS35 DIN-Rail or direct panel mount
74.1mm/2.9 in.
123.6mm/4.9 in.
61.5mm/2.4 in.
Type
DRAC DP 20
Type
DRAC GF 20
Ordering data
Part No.
6720005420
Approvals/Certifications
Enclosure Type
Description
cULus Listed to UL508A and C22.2 No. 14
File E223801
NEMA WD6, 5-20R
Description
cULus Listed to UL508A and C22.2 No. 14
File E223801
NEMA WD6, 5-20R
90
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
Part No.
6720005423
Notes
91
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
Notes
92
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
Singapore
Slovakia
Slovenia
South Africa
South Korea
Spain
Sweden
Switzerland
Syria
Taiwan
Thailand
Turkey
UAE
Ukraine
United Kingdom
Uruguay
USA
Venezuela
Vietnam
Yemen
Weidmuller is the leading manufacturer of components
for electrical connection technology to transmit energy,
signals and data. The Weidmuller product portfolio
ranges from terminal blocks, PCB connectors and
terminals, protected ­components, Industrial Ethernet
components, I/O components and relay sockets to
power supplies and overvoltage protection ­modules
suitable for all applications. Assemble Services, marking
solutions with a variety of tools and software systems,
round off the range. As an OEM supplier, the company
sets global standards in the field of electrical connection
technology.
Power Delivery and Protection Solutions
Catalog
Weidmuller, Canada
10 Spy Court
Markham, Ontario L3R 5H6
Telephone: (800) 268-4080
Facsimile: (877) 300-5635
Email:info1@weidmuller.ca
Website:www.weidmuller.ca
Weidmuller, Mexico
Blvd. Hermanos Serdán 698,
Col. San Rafael Oriente
Puebla, Puebla, Mexico
C.P. 72029
Telephone: 01 222 2686267
Facsimile: 01 222 2686219
Email:clientes@weidmuller.com.mx
Website:www.weidmuller.com.mx
Weidmuller, United States
821 Southlake Blvd.
Richmond, Virginia 23236
Telephone: (800) 849-9343
Facsimile: (804) 379-2593
Email:info@weidmuller.com
Website:www.weidmuller.com
010/11 • XM • LIT1291730000
This document provided by Barr-Thorp Electric Co., Inc. 800-473-9123
www.barr-thorp.com
11
Catalog
Iran
Ireland
Israel
Italy
Japan
Jordan
Kazakhstan
Kuwait
Latvia
Lebanon
Lithuania
Luxembourg
Macedonia
Malaysia
Malta
Mexico
Montenegro
Netherlands
New Zealand
Norway
Oman
Paraguay
Peru
Philippines
Poland
Portugal
Qatar
Romania
Russia
Saudi Arabia
Serbia
11
Power Delivery and Protection Solutions
Argentina
Australia
Austria
Azerbaijan
Bahrain
Belarus
Belgium
BosniaHerzegovina
Brazil
Bulgaria
Canada
Chile
China
Colombia
Costa Rica
Croatia
Czech Republic
Denmark
Ecuador
Egypt
Estonia
Finland
France
Germany
Greece
Hong Kong
Hungary
Iceland
India
Indonesia
CATALOG
www.weidmuller.com