UFO-RP2
FLUORESCENT BATTERY PACK
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed, including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. CAUTION - To prevent electrical shock, do not mate unit connector until installation is complete and
A.C. power is supplied to the unit.
2. CAUTION - This fixture provides more than one power supply output source. To reduce the risk of
electrical shock, disconnect both normal and emergency sources by turning off the A.C. Branch circuit
and by disconnecting the unit connector.
3. The battery is sealed, non-maintenance, and is not replaceable in the field. Please contact manufacturer for information on service. Do not attempt to service the battery please.
4. DO NOT USE OUTDOORS. The product is for use with grounded, UL Listed, indoor fixtures except in
heated air outlets or hazardous locations.
5. The product requires an unswitched A.C. Power source of either 120 or 277 volts. Properly cap the
unused A.C. Lead.
6. Do not mount near gas or electric heaters.
7. The product should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel.
8. This product is for use with 14 W through 54W(2'-4')T5 and T8 single pin or bipin for one lamp,Instant
Start and Rapid Start,14W through 39W(2'-4')T5 and T8 single pin or bipin for two lamp, Instant Start and
Rapid Start,18 W through 50 W (4-pin) long compact Rapid Start, or 32 W (4-pin) compact, 24W through
32W U-Bend FBT8 fluorescent lamps from Philips,Osram and GE or equivalent manufacture.
9. The product is compatible with all A.C. magnetic and electronic ballasts including multiple lamp ballasts
with one lamp operating in the emergency mode.
10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
11. Do not use this equipment for other than intended use.
12. Install in accordance with the National Electrical Code and local regulations.
13. Installation and servicing should be performed by qualified personnel.
14. Lighting fixture manufacturers, electricians and end users need to ensure product system compatibility
before final installation.
15. The battery is sealed,non-maintenance,and is not replaceable in the field. Please contact
manufacturer for information on service. Do not attempt to service the battery please.
16. The rated operating time in the emergency mode with battery is 1-1/2 hours and the recharge
time shall not be less than 24 hours.
SAVE THESE INSTRUCTIONS
Warning-This product contains chemicals known to the State of California to cause cancer, birth defects
and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise
touching this product.
CONTAINS NICKEL-CADMIUM
UL LISTED
R
RECHARGEABLE BATTERY.
MUST BE RECYCLED OR
DISPOSED OF PROPERLY.
Ni - Cd
Hubbell lighting, Inc,• 701 Millennium Blvd.Greenville SC 29607•864 678-1000•FAX (864) 678-1415•www.dual-lite.com
93039242-A
Page 1
INSTALLATION INSTRUCTIONS
NOTE: All the branch circuit wiring has to be ready as well as an unswitched source of power before the
fixture is installed. Both AC and Emergency Ballasts must be Fed From the same branch circuit.
CAUTION Battery connector has to be opened to prevent high voltage on output leads (Red and Yellow).
Wait until all the installation process is completed and AC is supplying power to the emergency ballast
before joining the battery connector.
1. AC power has to be off before installation.
2. Choose the right wiring diagram to connect the emergency ballast to AC ballast and lamp.
3. Please ensure the electrical connections conform to the National Electrical Code and local regulations if applicable.
4. Follow the diagram 1&2 to install the emergency ballast in the ballast channel.
DIAGRAM 1
DIAGRAM 2
Emergency Ballast
Test Button,Indicator Light(TBIL)
Emergency Ballast
Ballast Channel Cover
Test Button,Indicator Light(TBIL)
5. Wall switch has to be connected properly (Check diagram 3), Match the violet and brown leads to connect the TBIL to the
emergency ballast(Check diagram 4). The TBIL would be on after the fixture is installed properly.
DIAGRAM 3
SWITCHED FIXTURE
UNSWITCHED FIXTURE
WHITE
BLACK
WHITE
A.C. BALLAST
BLACK
WHT/BLK
(277V) ORG
1
HOT A.C. LINE
TBIL
WHT/BLK
WHT/RED
WHITE
COMMON
1
BROWN
+ RED
VIOLET
WHT/RED
WHITE
COMMON
UFO-RP2
(120V) BLK
WHT
A.C. BALLAST
Select proper voltage lead. Cap unused lead.
(277V) ORG
1
HOT A.C. LINE
TBIL
1
UFO-RP2
(120V) BLK
WHT
BROWN
+ RED
VIOLET
Select proper voltage lead. Cap unused lead.
6.Please search in readily visible location and stick the label with “CAUTION: This Unit Has More Than One Power Supply
Connection Point. To Reduce The Risk Of Electric Shock, Disconnect Both The Branch Circuit-Breakers Or Fuses And Emergency
Power Supplies Before Servicing.”
7. Do not join the inverter connector until the fixture is completely installed and AC power is supplied to the emergency ballast.
8. The battery needs to be charged for one hour in order to have short-term testing on the emergency function. Before having a
long-term emergency function testing, the battery in emergency ballast has to be charged for 24 hours.
NOTE: MARK AN APPROPRIATE LABEL ON INDICATOR LIGHT AND
TEST SWITCH AFTE INSTALLATION.
Page 2
OPERATION
THE CHARGING INDICATOR LIGHT WOULD BE ON TO INDICATE THE BATTERY IS BEING
CHARGED WHEN AC POWER IS APPLIED.
THIS EMERGENCY BALLAST WOULD FUNCTION AND OPERATE ONE OR TWO LAMPS
AT LEAST 90 MINUTES WHEN THE AC POWER IS FAILED.
THE EMERGENCY BALLAST WILL OPERATE 14WATT TO 54WATT LAMPS AT LEAST 90
MINUTES.
Illustration 1
Illustration 2
Recessed Troffer Fixture
FIXTURE
Strip Fixture
TBIL
FIXTURE
BALLAST CHANNEL COVER
UFO-RP2
UFO-RP2
PLASTIC TUBE
7/8 BUSHING
TBIL
FIXTURE LENS
OBSERVE PROPER POLARITY
NOTE: MARK AN APPROPRIATE LABEL ON INDICATOR LIGHT AND TEST SWITCH AFTER INSTALLATION.
MAINTENANCE
NOTE: SERVICES SHOULD ONLY PERFORMED BY QUALIFIED PERSONNEL.
THE EMERGENCY BALLAST SHOULD BE CHECKED PERIODICALLY TO CONFIRM
FUNCTIONING AND THE FOLLOWING SCHEDULE IS RECOMMENDED.
1) INSPECT THE CHARGING INDICATOR EVERY MONTH AND CONFIRM THAT IS
ILLUMINATED.
2) PUSH THE TEST SWITCH FOR 30 SECONDS TO ENSURE THE EMERGENCY BALLAST
IS FUNCTIONING. PERFORM THIS TEST EVERY 30 DAYS.
3) PERFORMING A LONG-TERM TEST (90 MINUTE BATTERY DISCHARGE) ONCE IN
EVERY YEAR. ONE OR TWO LAMPS SHOULD BE OPERATED FOR NO LESS THAN
90 MINUTES.
TABLE 1 (FOR BROWN CONNETOR)
LAMP
DIAMETER
T5 ,T8
SINGLE OR BIPIN
BASE TYPE
POWER
(LENGTH)
NUMBER OF
LAMPS EMER.
BROWN
CONNECTOR
14W-39W
1
CLOSE
2
OPEN
40W-54W
1
CLOSE
LONG COMPACT
COMPACT
U-Bend FBT8
4 PIN(2G11)
4-PIN
4 PIN
32W
24-32W
18W-39W
1
CLOSE
2
OPEN
40W-50W
1
1
CLOSE
CLOSE
Page 3
1
CLOSE
2
OPEN
EMERGENCY BALLAST AND AC BALLAST MUST BE FED FROM THE SAME BRANCH CIRCUIT
Typical schematics only may be used other ballast, consult the factory wiring diagram
WIRING DIAGRAM
For One Lamp Emergency Operation(14-54W)
B. TWO (2) LAMP INSTANT START BALLAST
A. ONE (1) LAMP INSTANT START BALLAST
BROWN
UFO-RP2
RED
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
BROWN
WARNING
WARNING
UFO-RP2
RED
WHT
RED
TBIL
Refer to Table 1 before connecting
WHITE COM
ORANGE
BLACK
UFO-RP2
RED
WHT
SWITCHED OR
UNSWITCHED
LINE
WHT/BLK
UFO-RP2
RED
WHT
TBIL
BROWN
UFO-RP2
RED
TBIL
WHT
WHITE
ORANGE
BLACK
WHT/RED
SWITCHED OR
UNSWITCHED
LINE
Refer to Table 1 before connecting
WHT/BLK
BROWN
WARNING
COM
WHITE
ORANGE
BLACK
BROWN
BLUE
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
BLUE/WHITE
Refer to Diagram 3 before connecting
BLUE/WHITE
WHITE
RED
RED
VIOLET(+)
BROWN(-)
AC
BALLAST
RED
RED
BLUE
BLUE
BLUE/WHITE
YELL/BLK
YELLOW
YELLOW
YELLOW
RED
TBIL
WHT
VIOLET(+)
BROWN(-)
UFO-RP2
WHT/RED
WHITE
RED
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
Refer to Diagram 3 before connecting
RED
LAMP 1
LAMP 2
LAMP 3(EMERGENCY)
I.FOUR (4) LAMP RAPID START BALLAST
SWITCHED OR
UNSWITCHED
LINE
Refer to Table 1 before connecting
WARNING
BROWN
WHT/BLK
BROWN
WHITE
ORANGE
BLACK
COM
YELLOW
YELLOW
AC
BALLAST
RED
RED
BLUE/WHITE
YELLOW
BLUE/WHITE
BLUE
BLUE
BROWN
BROWN
BLUE
BLUE/WHITE
YELL/BLK
RED
TBIL
WHT
VIOLET(+)
BROWN(-)
UFO-RP2
WHT/RED
WHITE
RED
Refer to Diagram 3 before connecting
WHT/RED
WHITE
RED
RED
VIOLET(+)
BROWN(-)
COM
BROWN
WARNING
SWITCHED OR
UNSWITCHED
LINE
WHT/BLK
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
H.THREE (3) LAMP RAPID START BALLAST
G. TWO (2) LAMP RAPID START BALLAST
Refer to Table 1 before connecting
WHITE
ORANGE
BLACK
BROWN
WHITE
RED
VIOLET(+)
BROWN(-)
COM
BROWN
WARNING
SWITCHED OR
UNSWITCHED
LINE
WHT/BLK
Refer to Table 1 before connecting
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
Refer to Diagram 3 before connecting
WHT/RED
Refer to Diagram 3 before connecting
WHT/RED
WHITE
RED
RED
VIOLET(+)
BROWN(-)
WHT
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
F. TWO (2) LAMP RAPID START BALLAST
E. ONE (1) LAMP RAPID START BALLAST
TBIL
UFO-RP2
Refer to Diagram 3 before connecting
WHT/RED
COM
WHITE
ORANGE
BLACK
BROWN
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
SWITCHED OR
UNSWITCHED
LINE
WHT/BLK
BROWN
WARNING
WHITE
RED
RED
VIOLET(+)
BROWN(-)
WHITE
RED
RED
Refer to Table 1 before connecting
COM
WHITE
ORANGE
BLACK
BROWN
BROWN
TBIL
SWITCHED OR
UNSWITCHED
LINE
WHT/BLK
Refer to Diagram 3 before connecting
D. FOUR (4) LAMP INSTANT START BALLAST
C. THREE (3) LAMP INSTANT START BALLAST
Refer to Table 1 before connecting
WHT/RED
VIOLET(+)
BROWN(-)
WHT
TBIL
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
ORANGE
BLACK
UFO-RP2
RED
COM
WHITE
BROWN
Refer to Diagram 3 before connecting
WHT/RED
WHT/BLK
Refer to Table 1 before connecting
WHITE
RED
RED
VIOLET(+)
BROWN(-)
WHT
TBIL
SWITCHED OR
UNSWITCHED
LINE
COM
WHITE
ORANGE
BLACK
BROWN
WARNING
SWITCHED OR
UNSWITCHED
LINE
WHT/BLK
Refer to Table 1 before connecting
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
Refer to Diagram 3 before connecting
RED
LAMP 1
LAMP 2
LAMP 3
LAMP 4(EMERGENCY)
NOTE: Use the proper input voltage lead, cap unused lead
Page 4
EMERGENCY BALLAST AND AC BALLAST MUST BE FED FROM THE SAME BRANCH CIRCUIT
Typical schematics only may be used other ballast, consult the factory wiring diagram
WIRING DIAGRAM
For Two Lamps Emergency Operation (14-54W)
A. TWO (2) LAMP INSTANT START BALLAST
SWITCHED OR
UNSWITCHED
LINE
Refer to Table 1 before connecting
WHT/BLK
BROWN
WARNING
WHITE
ORANGE
BLACK
BROWN
UFO-RP2
RED
TBIL
BROWN
UFO-RP2
Refer to Diagram 3 before connecting
WHITE
RED
RED
RED
WHITE
ORANGE
BLACK
BROWN
UFO-RP2
RED
WHT
TBIL
Refer to Table 1 before connecting
COM
WARNING
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
BROWN
UFO-RP2
WHITE
RED
RED
RED
TBIL
WARNING
WHT/BLK
BROWN
BROWN
UFO-RP2
RED
TBIL
WHT
Refer to Table 1 before connecting
SWITCHED OR
UNSWITCHED
LINE
WHT/RED
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
Refer to Diagram 3 before connecting
BLUE
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
BLUE
YELLOW/BLACK
YELLOW
BLUE/WHITE
Refer to Diagram 3 before connecting
BLUE/WHITE
AC BALLAST
RED
RED
BLUE
BLUE/WHITE
YELLOW
YELLOW
RED
TBIL
WHT
SWITCHED OR
UNSWITCHED
LINE
COM
WHITE
ORANGE
BLACK
BROWN
WHITE
RED
RED
VIOLET(+)
BROWN(-)
WHT/BLK
BROWN
WARNING
COM
WHITE
ORANGE
BLACK
WHT/RED
WHITE
RED
RED
VIOLET(+)
BROWN(-)
WHT
SWITCHED OR
UNSWITCHED
LINE
COM
WHITE
ORANGE
BLACK
F.THREE (3) LAMP RAPID START BALLAST
E. TWO (2)LAMP RAPID START BALLAST
Refer to Table 1 before connecting
WHT/BLK
BROWN
Refer to Diagram 3 before connecting
WHT/RED
VIOLET(+)
BROWN(-)
WHITE
RED
RED
SWITCHED OR
UNSWITCHED
LINE
WHT/BLK
BROWN
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
Refer to Diagram 3 before connecting
D. TWO (2)LAMP RAPID START BALLAST
C. FOUR (4) LAMP INSTANT START BALLAST
WARNING
COM
WHT/RED
VIOLET(+)
BROWN(-)
WHT
TBIL
Refer to Table 1 before connecting
WHITE
ORANGE
BLACK
BROWN
WARNING
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
SWITCHED OR
UNSWITCHED
LINE
WHT/BLK
Refer to Table 1 before connecting
COM
WHT/RED
VIOLET(+)
BROWN(-)
WHT
B. THREE (3) LAMP INSTANT START BALLAST
UFO-RP2
VIOLET(+)
BROWN(-)
WHT/RED
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
Refer to Diagram 3 before connecting
WHITE
RED
RED
LAMP 1
LAMP 2(EMERGENCY)
LAMP 3(EMERGENCY)
G.FOUR (4) LAMP RAPID START BALLAST
Refer to Table 1 before connecting
WARNING
WHT/BLK
BROWN
WHITE
ORANGE
BLACK
BROWN
RED
RED
YELLOW
AC BALLAST
BLUE
BLUE/WHITE
YELLOW/BLACK
BLUE/WHITE
YELLOW
UFO-RP2
BLUE/WHITE
YELLOW
BLUE
BLUE
BROWN
BROWN
RED
TBIL
WHT
VIOLET(+)
BROWN(-)
WHT/RED
SWITCHED OR
UNSWITCHED
LINE
COM
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
Refer to Diagram 3 before connecting
WHITE
RED
RED
LAMP 1
LAMP 2
LAMP 3(EMERGENCY)
LAMP 4(EMERGENCY)
Emergency only Operation
A. ONE (1) LAMP WITHOUT AC BALLAST (14-54W)
B. TWO (2) LAMP WITHOUT BALLAST (14-54W)
WHITE/RED
Refer to Table 1 before connecting
WARNING
WARNING
BROWN
BROWN
UFO-RP2
RED
TBIL
WHT
VIOLET(+)
BROWN(-)
BROWN
WHITE/RED
Refer to Table 1 before connecting
ORANGE
BLACK
WHITE
WHT/BLK
WHITE
RED
RED
BROWN
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
UFO-RP2
RED
TBIL
Page 5
WHT
VIOLET(+)
BROWN(-)
ORANGE
BLACK
WHITE
WHT/BLK
WHITE
RED
RED
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD