Page 1 of 45
========================
==================
= =============
===========
=======
====
==
Page 2 of 45
SL /
No
Name of Item
1.
Generator Portable
2500 W Kerosene
fuel
Rate per
Unit
49799.00
Name & address of
the Firms
M/S BIRLA POWER
SOLUTION
LTD,257,OKHLA
INDUTRIAL
ESTATE,PHASE-III,
NEW DELHI
Date of AT
and date of
recd by this
unit
30/05/09
30/07/09
Procured by: BSF,
DGS&D
2.
Angle cutter
(electric) Partner or
eqpt 2300W 45005500 mm
30845.00
M/S Hilti India Pvt Ltd,
F-90/4,Okhla Industrial
Area, Ph-I, New Delhi110020
Procured by BSF
Page 3 of 45
02.05.2008
02.06.2008
Specification
Rated output - 2100-2300 watt
Maximum Output 2400-2600 watt
Fuel : kerosene/Petrol
Rated current : 10.5 amp
Over load protector : for AC & DC Earthling
Other provision : Provision for battery charging, pull cord manual start
facility
Rated voltage : 220 Volts
Rated frequency :- 50 Hertz
DC Output : Only for charging 12 volts automotive batteries, Maximum
charging out 8.3 amp
Dimensión :- (LXWXH) 605 mm x 425mm x 550mm
(+20% margins)
Dry Weight : 60 to 65 kgs
Engine type : 4 stroke, 1 cylinder
Cooling system : Forced air cooling
Ignition system : transistorized coil ignition
Oil capacity : 1 to 1.5 liters
Fuel tank capacity : 12 to 15 liters
Voltage - 220-250 V
Wattage- 2000-2300 W
RPM –4500-5500
Disc Diameter max …350 mm(14”)
Noise level : <100 db
Arbor size 22- 22.5 mm With required accessories and electrical cord
of about 5 mtr. in length with 5 amp three/two pin plug.
With suitable Protective carry case.
Photo
Remarks
3.
Diamond tipped
blade ( dia .300
mm) for angle cutter
4680.00
M/S Hilti India Pvt Ltd,
F-90/4,Okhla Industrial
Area, Ph-I, New Delhi110020
02.05.2008
02.06.2008
RPM at least 6300
Arbor size- 22. mm to 22.5 mm
Dia 355 mm or 14”
Thickness-3.5 mm
Compatible with Rotary Rescue Saw
Procured by BSF
4.
Composite Blade
Network for angle
cutter (dia 300 mm)
1872.00
M/S Hilti India Pvt Ltd,
F-90/4,Okhla Industrial
Area, Ph-I, New Delhi110020
02.05.2008
02.06.2008
RPM 6300 or more
Arbor size- 22 mm to 22.5 mm
Dia 300 mm or 355 mm
Thickness-3 to 3.5 mm
Compatible with Rotary Rescue Saw
Procured by BSF
5.
Circular Saw
(Electric) with
Carbide Tipped
Blade
92,560/-
M/s Machinery
Marketing Associates
Pvt Ltd. 2e/24,
Jhandewalan
Extension, New Delhi55.
Procured by BSF
Page 4 of 45
13.03.09
15.09.09
1. Electrically powered motor operating in 100 to 250 volts with power
consumption between 1600 to 2500 watts. 15 ampere three core
electrical cord of 5 meter with three pin plug.
2. Idling speed of motor up to 200 to 3000 rpm with a maximum load
rpm of 1200 to 1500 rpm. The motor have a minimum endurance for
continues operation up to 60 minutes.
3. Incorporate easily locatable push button start and an electric brake
for quick stoppage.
4. Size of blade: 16” inches diameter with an arbor not exceeding 3.2
CM (1.25 inches). The blade provided will be carbide tipped blade
with minimum 32 teeth.
5. The cutting capacity of the blade exceeds 125 mm at 90 degrees
and 82 mm at 45 degrees. The saw should enable table blade rotation
and a depth adjustment lever. A shaft lock he has been provided for
effecting blade changes.
6. The weight of the saw with blade is not more than 17 kgs.
7. Rubberized wrap around saw and support handles with protection
arrangement for shielding operator fro, debris and kickbacks.
8. Noise level during operation at full load does not exceed 100 db for
a distance of one meter.
6.
7.
Circular saw
carbide tip blade dia
235 mm
7280.00
Electric drill (Bosch
GBM 10 or eqvt)
420 W, 2200 rpm at
no load.
1352.00
Machinery Marketing
Associates Pvt Ltd,
2E/24, Jhandewalan
extension, New Delhi110055.
13.03.09
M/S Bosch Ltd , 85 A
Dishamukh ,
Panchkuian Road ,
New Delhi-01
11/08/09
26.09.09
21/12/09
a) Blade type: Tungsten Carbide tipped used for wood cutting
b) Blade diameter: 235 mm
c) Compatibility: Compatible with Circular saw equipment
d) RPM: 5500 OR MORE
e) Thickness: 0.90 mm
f) Arbor: Compatible to circular saw
g) Others: Provision
Input power: 450 W
No load speed: 3000 RPM
Light weight
Shock proof body with different sizes of bits for both metal & wood.
Procured by CRPF
8.
Electric drill bit set
(complete set of 19
bits)
442.00
M/S Bosch Ltd , 85 A
Dishamukh ,
Panchkuian Road ,
New Delhi-01
Procured by CRPF
Page 5 of 45
11/08/09
21/12/09
a) Bit type: Material bits used for wood & metal cutting
b) Bit diameter: Complete set of 19 bits from 1 mm to 10 mm
c) Compatibility: Compatible with Electric drill equipment
d) Material- High speed steel
e)Hardness –760 HV Min, 900 HV MAX
f) Hand of cutting unless otherwise specified Right.
g) The drills shall be manufactured in one piece and shall be free
from cracks and burrs.
h) The two cutting edges of the center drill shall be diametrically opposite.
i) The drill shall be properly sharpened and ready for use.
j) Each center drill shall be covered with a suitable rust proofing material
IS 6708
9.
Come along 1.5 T
capacity with std
length 1.5 M (Titan
or eqvt)
23,69,722.5
0
M/s Shree Lalita, 1-B*, Prithvi complex,
Phase-11, Survey
No.128,Hissa
No.03,Village-Kalher,
Bhiwandi- Thane
(MAH)-421302
29.10.09
25.08.10
1. Capacity - UP TO 210 KG
2. Used for Lifting, lowering and pulling the load.
3. Chain length – not less than 3 meter
4 .Anchor hooks on both sides of the chain
5. Handle length 2 to 3’
6. Three positions for working of come along should be clearly marked at
travel lever as lift, lower and neutral.
7. With built in safety and free spool Facility.
Procured by BSF
10.
Fire extinguisher 20
lbs dry chemical
type
1775-60
M/s Hitesh Industries,
Plot No.2531, CIDC,
Metoda, Taluka,
Lodhika, Distt- Rajkot,
Gujrat.
Procured by CISF
Page 6 of 45
29.02.08
24.03.09
a) Size/Weight: 10 kg
b) Type: Dry powder chemical type BIS Specifications.
c) The shape of the body shall be cylindrical
d) The top dome and bottom end shall be dished outward (convex)
Without reverse curvature.
e) Non ferrous metal parts shall be brazed to the body.
f) The body to be made of mild steel
g) The dry powder used of BC Class or ABC class shall confirm to IS 4308
h) Each extinguisher shall be painted fire red confirming to shade No. 536
of IS-5.
11.
Portable Oxygen
Breathing Unit Set
Complete)
43, 312.50
M/S Udyogi Plastic (P)
Limited, 294, B.B.
nd
Ganguly Street, 2
floor, Kolkatta-12
18.08.08
(date of
supply order)
02.12.08
Procured by BSF
(SB FTR)
12.
Carbide tipped
chain saw
142800.00
M/S Brij Basi Fire
Safety Systems Pvt
Ltd,A-28, Hauz Khas,
New Delhi-16
Procured by ITBP
Page 7 of 45
29.01.10
21.05.10
1. Material have adequate mechanical strength, durability and
resistance to detoriation by heat or by contact with sea water or plain
water
2. Parts are easy to clean, examination and testing
3. Weight shall not exceed 14 kgs.
4. Leak proof on joints
5. Face mask is made up of either neopropane or silicon.
6. Face mask cover eyes ,nose ,mouth and chin.
7. Pressure gauge range 0-350 bars.
Engine
Power Ignition Weight Engine speed Chain speed Cutting chain -
Air cooled, 2 stroke engine, single cylinder petrol driven
5 to 6.5 HP
Electric ignition system
With in 12 kg
10000 to 14000 RPM
25 to 38 m/s
carbide tipped with locking key and solid bullet
raker gauge of size 404 pitch. 063 gauges
with heavy duty tie straps and tempered livers.
Noise level
less than 110 db @1 meter
Depth of cutting 6 to 8”
Fuel tank capacity – 0.70 to 1 ltr
13.
Distress Signal Unit
1,775-60
M/s M S A India, Ltd,
DLF- IT Park, Block –
th
AF, Tower – 01, 12
Flr, 08 – Artrial Road,
New Town, Rajar Hat,
Kolkata-56
23.03.09
09.06.09
Procured by CISF
14.
Inflatable Lighting
Tower (Aska)
(Emergency
Lightning System)
177418.71
M/s Aska Equipments
Limited, Aska House “
Gargashraya” 193
Deepali, Deepali
Chowk, Pitampura,
New Delhi-34
Procured by BSF
DGS&D supply
Page 8 of 45
27.09.07
28.09.07
The personal distress alarm device should give an automatic alarm
when there is no movement of the user for more than 20 to 25
second. This equipment should meet the following technical
specification:Dimension: Portable size and can be attached with waist belt with
off/on switch.
Audio Out-Put : Not less than 90 db at 3 meters
LED Indicator : LED light show working mode all the time
when unit is in operation.
Battery
: Compatible with equipments.
Battery Li
: At least 500 hrs stand by and 10 hrs full
Alarm :
Low Battery warning: It should give beep every 2 sec. To
give
Warning for recharging.
Full Alarm
: 2 to 4 signals/second at full noise level
1. Dimension –not more than 580x440x520mm
2. Wt- 50 kg
3. Total height-3-5 mtr
4. Light source- 400 watt
5. Illuminating area- 10000 sq mtr
6. Brightness- 4000 lumen
7. Generator -4 stroke engine (petrol), capacity-1200 VA
8. Tank capacity- not less than 7 ltr
15.
Inflatable Lightning
Tower – (Orbit)
172352.18
M/s Orbit industries,
U-123, MIDC,
Industrial Estate,
Hingna Road Nagpur
27.09.07
12.12.07
Procured by BSF
16.
17.
18.
Cordless Hammer
Drill – 144 Nos.
Cordless Hammer
Drill Bit Sets – 288
Nos.
Spare Battery – 144
Nos.
Page 9 of 45
14456.00
208.00
M/s Bosch Limited,
85 a, “Rishymook”
Panchkuian Road,
New Delhi- 01.
Procured by CRPF
13.02.10
Survey
Pending
Dimension –not more than 580x440x520mm
Wt- 50 kg
Total height-3-5 mtr
Light source- 400 watt
Illuminating area- 10000 sq mtr
Brightness- 4000 lumen
Generator -4 stroke engine(petrol), capacity-1200 VA
Tank capacity- not less than 7 ltr
1. Operating voltage – 18 Volt DC
2. Powered by – NI MH/LI-ION Battery or equivalent with a rating of not less
than 2.5 (AH)
3. Maximum torque- Not less than 60 nm or equivalent.
4. Should have at least a two speed transmission with no load speeds of 0-400
and 0-1500 rpm or higher and on impact of 0-4500 and 0-18000 blows-per
minute (BPM) or higher. The tool should provide a minimum of 10 clutch
settings.
5. The tool should have a keyless single sleeve not less than 1.27 Cms. Chuck
with carbide jaws and a ratcheting mechanism for easy tightening on bit.
6. Carbon brushes should be externally accessible for easy and quick
replacement.
7. The cordless hammer drill should not be more than 3.25 kgs in weight.
8. The tool should be able to metric drill more than 1.27 Cms. In steel 1.58
Cms. In masonry and 5.08 Cms in wood.
9. The tool should be providing with a support handle and both the tool and
support handle should have soft, Vibration absorbent grips for operator
comfort.
Accessories
1. The following accessories will be provided with each cordless hammer drill
set. Two spare batteries (in addition to one integral to the drill).
2. Battery charger, which should fully charge the battery in less than one hour
Two spare bit sets including driver bit.
19.
Gas cutter 450 mm
(Heavy duty)
2766.40
M/s M J Traders 1,
Bonfied Lane ,Kolkata01
28.01.10
15.07.10
Procured by ITBP
20.
Gas cutter/
regulator
3952.00
21.
Rubber Pipe Duplon
Type
7904.00
22.
Air lifting bag set
with air cylinder
930328-00
M/s Jyotech
Engineering & Mktg.
Consultants, H-49A,
Kalkaji, new Delhi-09.
Procured by BSF
14.08.08
19-02-09
1. Manual blow pipes for welding and cutting conforming to IS :
7635/1975
2. Pressure regulator for gas cylinder used in welding cutting and
related process conforming to IS : 6901/1988
3. Rubber hose for welding conforming to IS : 447/1988
The Air lifting bags are designed for lifting accidental vehicles, trains storage
tanks and parts of collapsed buildings.
DIMENSIONS
Minimum Diameter /Length (inflated) - Should not be more than 1000 mm
Maximum Diameter /Length (Deflated) - Should not be more than 1300 mm
Minimum Height (Center) - 60 to 90 mm
WEIGHT
: Proportionate to lifting capacity in each sets
LIFTING PROPERTIES
1. Lifting capacity - sets each of 70 tons, 100 tons and 150 tons capacities
2. Working Pressure - 08 to 10 bar
3. Safety Factor - At least 04
Page 10 of 45
23.
Combination Cutter
with Spreader
Power Unit
5,20,182.37
M/S Brij Basi Fire
Safety Systems Pvt
Ltd, A-28, Hauz Khas,
New Delhi-17
25.08.09
06.02.10
Procured by CRPF
24.
Diamond chain saw
4,99,000.00
Aska equipments ltd ,
plot no. C-21,dev
Bhoomi industrial
estate,
pohana,iqbalpur,villbantakedi,roorkee,distharidwar, uttrakand247668
Procuered by ITBP
Page 11 of 45
22.01.10
22.04.10
Combi tools shall have the following parameters: 1. Cutting Force
Not less than 200 KN
2. Spreading Force
Not less than 120 KN
3. Blade opening
Not less than 180 MM
4. Diameter of Round Steel Material for
Not less than 20 MM
cutting
5. Spreading Distance
Not less than 230 mm
6. Tool head rotation
360 degree
7. Weight
Not more than 12 KG.
The Diamond Chain Saw should have the following technical features:
1. Engine – 2 strokes petrol driven, air cooled, power shall be not
less than 5 H.P.
2. The starter shall be shielded from the dust & water. It shall have
electronic ignition protected from water and single spring clutch
proofed from water and concrete Fuel Capacity : 1 litre
(Approx)
3. The noise level should not exceed 102 dB at 01 mtr.
4. It shall be fitted with a diamond chain, which runs over the guide
bar. The chain saw shall be capable of cutting RCC up to 360 mm
thick and iron rod up to 12 mm dia.
5. The water supply required by the chain while cutting shall not
exceed 10 lts/Min
6. The chain saw shall also be provided with measures/attachments
for reducing the force required during cutting operation in order to
reduce fatigue on operator.
7. It shall also be provided with foam covered full wrap handles,
momentary contract on-off switch, water pressure gauge, 360
degree swivel hose connector, sprocket side cover and guard flap
for operator safety.
8. Weight – Not more than 20 Kgs.
9. Cutting rate – 10 to 25 “ per min or more
25.
Floating Pump
119250.00
M/s Newage industrial
7, Champaklal Udyog
Bhawan Sion (East)
Mumbai- 22.

30/07/08
10/03/09
Procured by CRPF
26.
Hammer drill
concrete
12600.00
M/s Hilti India Pvt Ltd,
F-90/4, Okhla
Industrial Area, New
Delhi. -14.
Procured by ITBP
Page 12 of 45
10.02.10











For the purpose of Fire Fighting and rescue operations. Light
weight, reliable, self priming pump that floats, discharges water @
at least 180 ltr/ min.
Casing : anodized Aluminum
Impeller : Bronze impeller
Water resistant air cleaner and muffler.
6 to 8 hp or more, air cooled.
Recoil starter with handle
Solid state ignition
Use unleaded gasoline/ Petrol and oil mixed
Minimum 2 years parts and service warranty
Automatic float controlled throttle
Compression release valve for easier starts
Dry weight is not more than 30 Kgs.
Power Input
Nominal Speed
10.05.10
Impact Rate
Electrical cord
Weight
Accessories
: Not more than 750 Watt on variable speed
: 0-900 (Right rotation – 900) (Left rotation not less than
400)
: Not less than 2 J
: 5 mtr in length with 15 amp plug
: Not more than 3.5 Kg.
: Adjustable bits of different diameter. 5 mm
And 10 mm for concrete, 10 mm & 15 mm
For steel and 20 mm, 30 mm, & 40 mm for wood.
27.
Portable Generator
set 10.5 KVA
(Silent Type Diesel
& Water Cooling)
206591.90
M/s Elmech
Engineering, Plot
No.06, Jayashree
Complex, Alumpur,
PO- new Kolorah, N H
06 Howrah-02.
30.01.10
17.05.10
Procured by NDRF
DGS& D
28.
Victim location unit
(with breaching
system)
413800.00
M/s Joytech
Engineering & Mktg
Consultant, H-49 A,
Kalkaji New Delhi.
Procured By CRPF
Page 13 of 45
30.03.2009
19.09.2009
1.
Alternator :The alternator shall be self excited and self regulated of
specified KVA.
RATING in single./Three phase at 240/415 volt, 50 Hz, 1500
RPM and 0.8 pf lagging power factor, and shall conform to IS : 13364
(Part 1) :1992 (up to 20 KVA) or IS : 13364 (Part-2) :1992 above 20
(KVA) . The alternators shall be of brush type or brush less type with
VG-1 Grade of voltage regulation for ratings up to 80 KVA and of
brush less type only for ratings above 80 KVA with VG-3 grade of
voltage regulation. The alternators shall be screen-protected drip
proof with Min IP 21 degree of protection as per IS: 4691/85
2.
Diesel Engine
Diesel Engine shall be air or water cooled as specified,
electric start developing required B.H.P. at 1500 RPM with class A-2
Governing or better for alternator to deliver specified continuous KVA
output at 0.8 lagging pf at NTP conditions. The Diesel Engine should
be capable of providing 10% overload for one hour or every 11 hours
continuous running at full load. Turbocharged Engine shall conform to
BS : 5514/BS 649, other non turbocharged Diesel Engine shall
conform to IS 10000 Series standards as applicable.
A.
Video:
Camera – Colour ¼ CCD minimum 0.4LUX/5LUX (therefore, does not
require much light in the dark)
Illumination
- 16 element LED lamp / Xenon lamp
Display monitor – Not less than 6 to 8” diagonal, flat sceen LCD active
matrix
Auxiliary output – Suitable accessory multi port.
Video Standard – PAL
B.
Audio:
Search microphone - High sensitivity with variable gain amplifier.
Sensitivity: 40dB +/-5dB @ 1V/Pa 1 kHz @1/4”
Distortion : >3% THD @ Db SPL
Maximum Gain: Not less than 90 db
Search Speaker - Simplex system element in camera housing
Operator handset (standard) – Noise attenuating, boom microphone under
helmet style
C.
Dimensions:
System length – Telescopes from 100 to 250 cm
Probe weight – Not less than 3.5 Kg
Camera housing diameter – Not less than 4 cm
Minimum access diameter – Not less than 4cm
Articulation level - 180º total – right to left
Total area viewed – Not less than 220 º
Viewing distance – 1.5 to 6 M (150cm-6m) in total darkness
D.
Battery
Type – Sealed lead acid
Endurance – 3 hours continuous operation
Recharge: 2 hours to 90%
Charger – AC dual voltage – Switch able (220 Volts)
E.
Environmental
Operational temperature: - 10º to 50º C
Storage temperature: 0º - (4ºC to 36ºC)
Humidity: 10% to 90% relative
Water Resistant: High Water Resistant
F. Storage Case: Suitability to the equipments
Type
: – water tight and dust tight
Weight (Loaded) – Not less than 25 Kg
Breaching system
Page 14 of 45
133000.00
SPECIFICATION OF THE BREACHING SYSTEM
Power Train – Two Cycle, 40 CC, 2.75 Horsepower, Centrifugal Clutch.
Power Head Weight – 25 Pounds – 11.4 kgs.
Speed – 950 RPM
Boring Speed – 3” Per Minute – 7.6 cm per minute Standard Construction
Grade Concrete Results may deviate depending upon variables
Spindle – 1-1/4 x7 threads per inch.
Bits – 2 2”x17” (5.1cmx43.2cm) Diamond Faced tin kerfs – close segment
2 –2” 17(5.1cm x43.2cm) Carbide Faced.
Maximum Bit Size – 4” (10cm)
Cooling – Pressurized Water Can, 2 Gallon Capacity, Hose – 12’ (3.7m)
with quick-Connect fittings.
Field Service Kit – Canvas Storage Pouch, Spare Fuel Tank Cap, Starter
Recoil Assembly, 2 Piece Allen Key Set for Starter Assembly, Spare Spark
plug Spark Plug Wrench, Copper Washer, Garden Hose to Water Collar
Adaptor.
Spindle Extensions – 12” – 30.5 cm – OPTIONAL up to three may be used.
Storage Case – High Impact Plastic Wheeled, 32” Lx21Wx12”D (81cml x
53cmW x 31cmD), Weight Loaded – 75 pounds (34kgs.)
29.
Leak tester for
testing respiratory
eqpts
50062.50
M/s Industrial
Engineering
th
Instruments, 203, 12
rd
Main Road, 3 Phase,
Peenya Industrial
Area, Peenya,
Bangalore, KR.
Procured by CISF
Page 15 of 45
01.09.09
19.12.09
The Mask Leak tester shall consists of two dummy heads fixed on a
base plate, a micro suction generator generates a suction, which is
applied to the dummy head through a rubber tube. The M.L.T. shall
consist of two fixed headed on a based plate. A Micro suction
generator that could be attached to dummy through a rubber tube
through a micro flow meter. The tester shall be capable of attending a
steady stage reading within 40 sec & shall be powered with a built in
timer that stop and the circulated freezes the displays after 40
Second. The test result shall be shown by glomming red or green
LED there by meaning Fail or Pass status of the mask tested. The
tester shall be ready for next operation by pressing a reset switch.
The materials used the communication of components of leak
tester shall conform to international standard and a certificate to this
effort from an independent test lab orating of repeat shall be
submitted along with officer. The unit shall be marked with the
relevant speed, Name of the manufacture, Year of Manufacturing of
the operating materials. The complete Leak Tester not shall be
provided in a carrying case prefab arable water & dust resistant type.
The suction generated by the micro suction generator is further
reduced using a needle
valve and passed through a micro flow
meter and applied to the cavity of the dummy head. The mask to be
tested is fitted on the dummy head by tightening the straps. The
suction generator supplies a known amount of the suction to the
cavity of the mask.
The steady state reading is attained in a time of less than 40
seconds. There is a built-in timer, which stops the circuit and freezes
the displays after 40 seconds. The operator can decide whether the
mask passes or fails seeing the criteria given. A decision making
circuit is also incorporated which automatically compares the test
values with admissible values and declares the result by glowing
green/red LED meaning pass/fail.
30.
Life Detector
TYPE -I
USD $
14850.00
M/s Unicare
Emergency Equipment
nd
Pvt Ltd. 2 Flr ,
Leslico House
Professer V S Agashe
Road, Dadar West
Mumbai.
13.4.2009
(A)
19.3.2010
MAIN UNIT
Input of sensor/Intercom/Probe
Seismic Sensor input impedance
Intercom probe input impedance
Headset Output
For headphones
: > 6 K Ohms
: > 2 k Ohms
: 1/4 “ stereo
jack
Received from SIW
Tigri Camp New Delhi
Procured by BSF.
Output power, variable
Frequency Range
1 Hz to 3000 Hz
Filters (Fixed Switch able)
“Rumble”
: 0.13 W/60 Ohms
“PWR”
: notch 50 Hz and 60
: High pass
100 Hz
Hz
“Hiss”
: Low pass 600 Hz
Signal Display
LED Bar graph any 2 channels or sum of all channel, range
60 db.
(B)
SEISMIC/ ACOUSTIC SENSOR (POSITION INSENSITIVE)
Frequency Range
: 1 Hz to 300 Hz
Shock resistant
: > 1000g
(C)
POWER SUPPLY
Battery operated, low battery alert
Alkaline battery type
: Appropriate
Operating time at approx. 20 deg.C
: >20 hrs.
Ext. DC Input
: 10.8 to 28.8 VDC
AC/DC converter, AC line frequency
: 47 to 63 Hz
Nominal AC line voltage : 100 to 240 VAC
(D)
AMBIENT TEMPERATURE
Storage and transport : -20 degree to + 70 degree C
Nominal operating range: -15 degree to + 60 degree or more.
Page 16 of 45
31.
Life Detector
TYPE -II
$ 31,715.00
USD
M/s Jyotech
Engineering &
Marketing
Consultants, B-127,
Sector- 65, Noida,
Distt- Gautam Budh
Nagar-201301 (UP).
Procured by NDRF
HQ
Page 17 of 45
05.05.2010
1. Detection Range – 500 Mtr
2. Detect non-uniform electric fields of livings humans.
3. Field of view
 Horizontal Plane : At least –2 to +2 degrees
 Vertical Place :
 At least –60 to + 60 degrees in the open air
 Ar least -40 to +40 degrees in a composite structure
 -20 to +20 degrees on an all- metal grounded platform
 Detection range : It will come with two range adjustment
devices (RADs) as follows:

All metal RAD Upto 500 meters

Composite RAD Upto 20 meters
4. Target tracking – in detection mode, once the Life Detector has
fixed on the target, even if it moving, the Life Detector will
continue tracking the target.
5. It will have a in built Red laser (used to show derection in dark
areas) and will be eye safe. The laser environmental
parameters for optimum performance will be : Operating temperature
: -10 to +45 degrees
Celsius
 Storage temperature : -40 to +85 degrees Celsius
6. Instrument will be water resistant.
7. Power : (Internate) – rechargeable 8.4 V DC battery for the
laser.
 Operating time
: 03 hours in
continuous operation.
 Charging time
: 14 to 16 hourscharger should be provided.
8. Weight - ^1 Kg
9. Hard carrying case or bag for accommodating the instrument
will be provided.
10. Instrument environmental parameters for optimum performance.
 Operating temperature
: -40 to +85 degrees
Celsius
Storate temperature
: -40 to +85
degree Celsius
32.
Head Light
Pelican Heads up
2680 recoil led 300
Nos.
2697.75
M/s B L Health &
Safety Pvt Ltd. B L
House 161, J-Gautam
Nagar, New Delhi- 49.
19.02.10
10.06.10
Procured by BSF
33.
Reflective Jackets
118.00
M/s MKU Pvt Ltd, 625
Ka 638 & 639 Vill
Khujapur, Rooma,
Distt- Kanpur (UP)
Procured by BSF
02.03.09
Role : For use during rescue operations, illumination for low light
objects at rescue sites.
Main components of Head Light & their specs.
1. Can be mounted on safety Helmet with mounting bracket/ durable
head bands.
2. Single unit.
3. Water resistant.
4. Rugged in use with heavy duty switch.
5. Beam of light focused with no dark patches.
6. Light source- LED
7. Watt – 01.
8. Voltage – 06 Volt.
9. Weight with batteries- 12 oz (Max)
10. Designed to meet the requirement of class, I, II & III
Fluorescent colour jacket with 50mm glass bead type reflective tape in 2
vertical and 1 horizontal band in front and back same. Front opening
and v neck design.
24.12.09
Background Fabric:100% polyester, 125 gms made from bright glossy yarn, adhering to EN
471 standard. It shall have excellent colour fastness and should be UV
treated.
iii) Colours:- Fluorescent reddish orange / fluorescent
lime-yellow.
iv) Reflective Tapes:Glass bead type reflective tape, EN 471 class 2 approved, 50 mm
wide, colour of the reflective tape will be silver grey.
Accessories:
i) Binding: - Binding will be black in colour. 100% polyester fabric will be
used in binding with excellent colour fastening. Binding is 100% leak
proof.
II) Velcro: - Velcro shall be 25 mm wide and 50 mm in length
positioned vertically for perfect fastening. The colour of the velcro will
be black. size: length : 27 inches and width 23 inches.
Page 18 of 45
34.
Self Contained
Positive Pressure &
Open Circuit Type
Breathing
Apparatus
Model PA 94 Plus
42,224.00
M/s Joseph Leslie
Drager Mfg Pvt Ltd.
87-C, Leslice House,
Prof, F S Agashe
Road, Dadar (W)
Mumbai- 28.
Procured by CISF
23.04.09
11.08.09
GENERAL REQUIREMENT
The compressed air breathing apparatus shall be so designed so that
the wearer can breathe comfortably, without any risk of poisonous
gases entering the breathing circuit. The breathing circuit should be
so designed so that there is optimum utilization of compressed air
stored in the cylinder during Fire Fighting and rescue operations. The
set as a whole shall be so designed so that the handling of the set is
easy and does not cause any damage to the set. Set shall be capable
of being used with cylinders having working pressure up to 300 bar at
least. The BA set should have no air losses. No toxic matter can enter
the mask back plate should be ergonomically designed for comfort
and stability and there should have provision of connection between
wearers.
MATERIAL
All the materials used in the construction shall have adequate
mechanical strength, durability and resistance to deterioration by heat
or by contact with seawater or plain water. Such materials shall be
antistatic and fire resistant as far as practicable.
Exposed parts excluding cylinders, that is, those, which may be
subject to impact during practical performance tests, shall not be
made of magnesium, titanium, aluminum or alloys containing such
proportions of these metals which on impact give rise to frictional
sparks capable of igniting flammable gas mixtures.
Materials that may come into contact with the skin shall be nonstaining soft, pliable and shall not contain dermatitis substances.
The apparatus shall be sufficiently robusted to withstand the rough
usage; it is likely to receive in service and designed so that it will
continue to function satisfactorily while temporarily accidentally
submerged in water at a maximum depth of one meter and thereafter
until the air in the cylinder is exhausted.
SEPARATION OF PARTS
The design and construction of the apparatus shall permit its
components parts to be readily separated for cleaning, Examination
and testing. The couplings required to achieve this shall be readily
connected and secured, where possibly by hand, and means for
sealing used shall be retained in position when the joints and
couplings are disconnected during normal maintenance.
ADJUSTABLE PARTS
All parts requiring manipulation by wearer shall be readily
accessible and easily distinguishable from one another by
touch. All adjustable parts and controls shall be so
constructed that their adjustment is not liable to accidental
alteration during use.
WEIGHT
Page 19 of 45
The weight of the apparatus shall not exceed 14 Kg. The
cylinder used for compressed air should have the approval of Chief
Controller of Explosive.
LEAK TIGHTNESS
The apparatus shall be of positive pressure type so as to prevent
ingress of
the external atmosphere. There should be not leakage from any joint.
Air line connection and second user connection and inletcum-outlet shall be provided on the pressure reducer for
attaching, airline connection for second user connection.
.
FACE MASK
The face mask should be made either of Neoprene or
Silicone. The air inlet value should connect to the mask by simply
clipping it on the enable wearer to switch on the positive pressure at
the last minute.
.
Face mask shall cover the eyes, nose , mouth and chain , it
shall be provided with an additional flap for providing adequate
sealing on the face of the wearer of the breathing apparatus against
the outside gas, when the skin is drying or moist, when the head is
moving and when the water is peaking.
The face mask shall have an inner mask to reduce misting
and dead space so that the mask is always remain centered.
Face mask shall be secured to the face by means of an
adjustable. /replaceable head harness and they shall be fitted with a
neck strap to support them when not being worn. There shall be five
head harness but one strap i.e. the top one should be prefixed.
Means for speech transmission shall be incorporated and so designed
that it is in front of the mouth.
The face mask shall be constructed of silicon rubber in order that it is
soft, light in weight, comfortable to the wearer to wear for long
duration, resistant to to chemicals and heat, thus having longer life.
The connection for demand valve shall be provided in front of the
Face Mask.
The visor shall be made of clear polycarbonate.
FACE CONNECTOR
The connection between the face mask and the demand
valve shall be of Click-on/Push fit type well secured so that,
the set is having fully automatic positive pressure , there is
optimum utilization of compressed air stores in the cylinder
and the mask by mistake is not used with a filter canister.
HEAD HARNESS
The head harness shall hold the face mask firmly and
comfortably in position. It shall be molded from silicon rubber. It
should be easily detachable for cleaning and decontamination. There
Page 20 of 45
shall be five quick release harnesses out of which only 4 shall need to
th
be tightening with the 5 i.e. top one shall be prefixed to ensure quick
donning and center placing of the mask while wearing.
BODY HARNESS
The body harness shall be designed to allow the user to done
the apparatus quickly and easily without assistance and shall be
adjustable for fit. Buckles fitted to waist and shoulder harness shall be
so constructed that once adjusted they will not slip.
.
EXHALATION VALVE
The apparatus shall be provided with an unidirectional
exhalation valve spring loaded to maintain positive pressure in the
face mask. The resistance of the valve should not exceed 6 mili ar, it
shall be protected against dirt and mechanical damage.
DEMAND VALVE
It shall be fully automatic positive type. Designed to provide a
flow rate of at least 50 ltrs /min at all cylinder pressure above 20 bars.
It shall be designed to push fit/click on to the mask.
SUPPLEMENTARY SUPPLY
The apparatus shall be provided with a manually operated push type
means on the demand valve itself for supplementary supply.
HIGH PRESSURE TUBE
It shall be having outer covering of neoprene rubber .The test
pressure of the tube shall be above 600 bar. It shall be fitted to the set
in a manner that it cannot be separated by hand. The entire high
pressure tube shall be covered by a medium pressure tube having
medium pressure supply for safety reasons.
MEDIUM PRESSURE TUBE.
It shall be having outer covering of neoprene rubber. The test
pressure of the tube shall be above 20 bars. It shall be so designed
that it can be separated by hand and cannot be fitted at the joints
where High Pressure Tube is fitted.
PRESSURE GAUGE It shall indicate pressure on opening of the
cylinder. The range shall be 0-350 bars. It shall be placed that the
wearer can easily see the pressure while using the set.
The pressure gauge shall have a blowout release. The
blowout release should be so located that in the event of an explosion
or fracture of the pressure element of the gauge, the blast will be
away from the front. The gauge window shall be made of material of
non-splintering glass or of clear plastic materials.
A tap or restrictor shall be provided so that if pressure gauge
and connection hose are removed from the apparatus, flow will not
exceed 25 lit/Min at full cylinder pressure, if the gauge or flexible
connecting tube be damaged after the apparatus has been
functioning for a period of time equal to half the nominal working
duration with an air consumption of 40 l/min the loss of air from the
Page 21 of 45
35.
Ventilator & Air tube
– 72 Nos.
69, 000.00
M/s Newage
Industries, 7 Chamak
Lal udyog Bhawan,
Sion (East) Mumbai22.
Procured by BSF
Page 22 of 45
24.07.2007
06.12.2007
30.01.2008
damaged component shall not reduce the normal effective duration of
the apparatus by more than the reserved period.
WARNING DEVICE
The apparatus shall be provided with warning whistle next to the
pressure gauge. It shall be consuming minimum amount of
compressed air and should emit continuous at least 90 dbls sound.
Warning whistle next to pressure gauge enables to user to ascertain
his whistle and can check the same.
BACK PLATE
It is to be made of non-metallic GRP reinforced or equivalent material
resistant to heat and chemicals. It should not be made of steel or
metal (with or without any covering or coating) to avoid heating and
slipping of the entire set. Rubber sheeting prevents ventilation. The
back plate shall be so designed that the use can lift the set by having
a firm grip of back plate in order to avoid lifting of set from cylinder
valve or body harness. The method of fixing cylinder shall be such
that 4,6 and 9 liter cylinder of working pressure 200/207/300 bar can
be fitted without any alternation.
PRESSURE REDUCER
The apparatus shall be provided with a diaphragm less piston
pressure reducer which is capable of reducing pressure from 300 bar
to 7 bar (approx) The designing shall be such that back pressure
development shall be minimum, second inept/outlet shall be provided
on the reducer. High pressure and medium pressure safety shall also
be provided on the reducer.
.
GAS CYLINDER & MAIN VALVE.
Cylinder used shall be of steel having 6 ltr water capacities, 300 bar
working pressure 1800 Liters compressed air for 45 minute duration.
The cylinder & valve should be approved by Chief Controller of
Explosive, Nagpur, India.
1. This used for extracting smoke, harmful gases and vapours. Also suitable
for supplying fresh air to areas filled with harmful gases, for example during
maintenance works in tanks.
2. Powered by a 4- stroke petrol-engine, hand starter, speed regulator and
suppressing plug (2-2.6 KW)
3. Ventilator output max. 3600 m3/ hour at free discharge.
36.
Safety Torch
940.00
M/s Joseph Leslie &
Co. Leslico House,
Professor V S
Agahase Road Dadar
West Mumbai
Procured by BSF
Page 23 of 45
11.12.07
01.03.08
1. POWER SOURCE - CARBON ZINC ONLY : 3XD CELL
2. BULB/LAMP : PR-3
3. BULB/LAMP LIFE - 15 HOURS
4. LIGHT OUT PUT - 15,000 BEAM CANDLEPOWER
5. WEIGHT (WITHOUT BATTERIES) - 6 OZ (.17 Kg)
6. WATER PROOF
7. SUITABLE FOR USE IN HAZARDUOUS ATMOSPHERE
8. SPARE BULB COMPARTMENT
9. RING HANGER
10. THREE WAY SWITCH : ON - OFF - FLASH
11. ANTI - ROLL TUBE
12. OVERSIZED FACETED REFLECTOR FOR MORE LIGHT
13. UL APPROVED
========================
==================
= =============
===========
=======
====
==
Page 24 of 45
SL /
No
1.
Name of Item
Oxygen
concentrator
Rate per
Unit
88,400/-
Name & address of
the Firms
M/S M.G.M
ASSOCIATES, NEW
DELHI
Procured by BSF
2.
ECG Machine with
Analyzer
Date of AT
and date of
recd by this
unit
29.08.2007
08.12.2007
Specification
Dimension
Weight
Delivery Rate
Oxygen %
Electric Requirement
Power Consumption
: 28” h x 16” w x 14” d
: 52 lbs
: ½ - 5 liters (1/2 Liter increments)
: 93% @ 1-5 liters (=/-3%)
: 115 v, 60 Hz
: 400 watts average.
1. Pressure – relief value and thermal protection on the compressor
2. Filtration for longer bed life and better oxygen purely.
3. Increased flow rates, decreased operating temperatures and
longer life with less cup seal wear.
4. Double insulated unit. two prong plug.
5. Humidifier port helps prevent humidifier bottle and connection
breakage.
6. The opening is wide to make it easy failure alarm.
7. High/ Low pressure alarms and power failure alarm.
8. Long cannula while maintaining an accurate flow setting
(maximum 50 feet)
9. Audible and Visual sensing device for low pressure, power fail and
power on.
Power Supply
AC Mains/Built in Rechargeable battery operation
Mains
: 110/220 v ± 10% 48-60 Hz
Rechargeable battery
: 2 x 6.3 V; 2.6 Ah;
Power consumption
: 22 VA
Fuses
: Battery fuse-1.25 A;(220 V) or 0.44(110W)
Recording
Paper
: Thermo sensitive
Paper width
: 50 mm (recording: 40 mm)
Recording speeds
: 25 and 50 mm /sec (switch selection)
Recording length on RC Battery : 100 m at 25 mm/Sec or 200 m at 50
mm/sec for typical one battery charge.
LEAD SELECTION
Leads
Selector position
Page 25 of 45
: Electronic 12 leads selection
: Test, I,II,III, aVR, aVL, aVF,V
Photo
Remarks
FREQUENCY RESPONSE
Frequency response
: 0.3 Hz to 120 Hz (AHA) without Filter
0.3 to 100 Hz (IEC) with filter
Time constant
: 1.5 seconds
Filter
: Muscle-tremor filter
SENSITIVITY
Sensitivity
: 1.5 mm/mV or greater, continuously
variable from 0
to 15 mm/mv with marking for 10 mm/mV calibration.
Calibration
: 1 mV push-button, generated by
electronic circuitry.
Damping
: 5-10 % overshoot
Input impedance
: 10 M ohms
CMMR
: Batter than 80 Db
GENERAL:
Dimensions
: 297 x 210 x 80 mm
Weight
: 4.2 kg without batteries
3.
Pulse Oxymeter
30,160/-
M/S SAMPARK
MEDICARE, B-4, 92A
KESHAV PURAM,
DELHI-110035
Procured by BSF
Page 26 of 45
20.06.2007
MEASUREMENT RANGE:
08.12.2007
SPO2 2 1-100 %
Pulse Rate 20-300 beats per minute (bpm)
Accuracy
SpO2
Adults 70-100 % + 2 digits
0-69% specified
Neonates 70-100 % + 3 digits
0-369 % unspecified.
Pulse Rate
0-250 bpm + 3 bpm
sses 68% of the population.
Power Requirements
100-240 VAC
50-60 Hz
15 VA
Pulse Rating : 250 A/2A
Battery Type- Lead acid with 3 hrs of Battery Backup
Operating Temperature
Instrument
: 10 to 45 º C
Sensor within physiologic range for specified accuracy.
Weight : 1.3 Kg (max) without pole amount screws
Size : 60 (H) x 200 (W) 120 (D) mm % SaO2:
Range : 0 % …. 100 %
Resolution : 1%
Accuracy : 50-60 % , Range + 3% , 70-100 % Range + 2%
Trends : Pulse Rate-1 hr, 12 hr, 24 hr, SAO2,-1 hr, 12 hr, 24 hr
Numeric data display: SPO2 & Pulse Rate (LED +LCD) with backlit
LCD display for plesthysmograph with adjustable brightness.
Auto gain control system.
4.
Nebulizer
12,480/-
M/S M.G.M
ASSOCIATES,2 LOK
VIHAR APT,
VIKASPURI, NEW
DELHI
04/06/07
08/12/07
1. Aerosol with piston Electro compressor
2. Nebulising speed : 1 cc in 3 minutes
3. Pressure 1:1 bar
4. Air flow 15 liter/ minute
5. Noise Level : 60 dB
6. Granulo metric size of medication: 1-10 microns by means of multi
PIPSER component.
Procured BY BSF

5.
Portable Anesthesia
apparatus kit
32,136/-
M/s Manchanda
Medicos, 17 A/L
Shopping Centre,
ShalimarBagh, Delhi110088.
Procured by CISF
Page 27 of 45
AT No.290
dtd
23.03.2009
The machine has to be a complete portable anesthesia machine
with all accessories built on a light weight metal frame with
foldable built in stand.
 Provision for halothane vaporizer with glass bottle.
 Flow meter unit for oxygen & Nitrous oxide.
 Oxygen & Nitrous Oxide regulators with pin-index system
separately for
 Brain‟s circuit complete with bag mount corrugated tube
minimum 40 inch in length
 Re-breathing bags of all sizes.
 Face mask padded of all sizes (Pediatrics to adult).

Catheter mounts.

Pediatric circuit with T-Piece arrangements

Facility for emergency oxygen & Nitrous.

“A” type gas cylinders for oxygen & nitrous oxide.

Nitrous oxide tube 9 inch (230 mm) with fine adjustment control.

Max- connection for B & C type gas cylinder.

Tools kit.s

Carrying case for anesthesia machine with accessories.
6.
Semi Automatic
Blood Analyzer
87,360/-
M/s Recorders &
Medicare Systems (P)
Ltd. 181/15, Phase-1
Industrial Area,
Chandgarh-02
PROCURED BY CISF
AT NO.297
dtd
31.08.2009
03/12/09
01.
02.
03.
04.
05.
06.
07.
08.
09.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
Page 28 of 45
Dual mode flow cell and cuvette.
Built in voltage stabilizer.
Specially designed Cuvette block with control for temperature
regulation.
Capable of saving 200 tests with QC Graph.
Option to enter Patient ID.
Monochromatic and Bi-chromatic readings.
o
o
0
o
Selectable temperature: 37 , 30 or 25 C. + 0.1 C.
Calculation of results either by factor or by standard
concentration.
Versatile software to calculate the Delta OD on screen.
Built in Thermal Printer: high resolution, 320 dots per line with
full graphic facility.
Automatic sensing of cuvette insertion.
Built in real time clock.
Operator interface: Touch panel & mouse.
Linear measurement range: 0.000 to 3.000 absorbance units
(A).
Optical measurement.
Type of filter: interference.
Wave Length: 340,405,510,546,578,630nm & two optional
positions
Half Bandwidth: 10nm + 2nm.
Filter Selection: Automatic.
Cuvette/Flow cell: Supports both cuvette and flow cell.
Flow cell Sipping Volume: 500 microlitre.
Flow Cell Volume: 18 Microlitre.
Sipping mode: Automatic by specially designed planetary
gear pump.
Cuvette Volume: 500 microlitre.
Temperature control of Cuvette/flow cell Block: By selectable
peltier elements.
Light Source: Tungsten Halogen 6 V. 10W with life saving
features.
Display. 50 Graphics LCD.
Analysis Mode: Kinetic defferential, ratio: Absorbance, end
point, fixed time.
Memory capacity: 64 KB non volatile RAM with battery
backup:. Report generation for last 1000 sample stored and
obtained by date, ID, both by date & ID.
Rs. 232.00 serial port: 9600 baud, 1 start, 8 data, 1 stop.
Wattage- 50 Watts or as per the instruments load.
0
o
Operational Temperature: from 10 C to (+) 37 C.
Relative Humidity: UP to 85%.
Semi micro Cuvetts : 25 Nos. with each unit.
35.
36.
37.
Page 29 of 45
Paper Roll (Thermal): 25Nos with each unit.
Variable volume pipette.
2 ul to 20 ul : 01 No. with each unit.
5 ul to 50 ul : 01 No. with each unit
50 ul to 100 ul: 01 No. with each unit
100 ul to 1000 ul : 01 No. with each unit.
Compatible UPS for the system.
========================
==================
= =============
===========
=======
====
==
Page 30 of 45
SL /
No
1.
Name of Item
Rate per
Unit
Name & address of
the Firms
Date of AT
and date of
recd by this
unit
Inflatable motor
rescue boats small (
10 seated )
314022.89
M/S Fibroplast, C30, Sector – 58,
Noida, Gautam Budh
Nagar, UP.
19/07/08
15 Nos
14.02.09
11 Nos
23.02.09
13 Nos
30.04.09
29 Nos
17.05.09
04 Nos
31.05.09
procured by BSF
2.
3.
Synthetic Life jacket
MK-I (CAT-NIV)
8640 Nos.
Life buoys
675/-
2197.23
M/s Shri Lakshmi
Cotsyn Limited 19/x-1,
Krishnapuram, G T
Road, Kanpur- 208007
(UP).
M/S BHARAT
TRADER, UNIT
RD
NO.21, 3 FLOOR,
MAHALAXMI
INDUSTRIAL
ESTATE, GANDHI
NAGAR,DC ROAD
LOWER PAREL,
MUMBAI.
Procured BY CRPF
Page 31 of 45
10.07.09
156 + 50
(RRC)= Unit
purchase
31/03/09
16/07/09
20/07/09
21/07/09
27/07/09
(270 NOS
On each
Date)
Specification
Made mercury
HP-25
RPM-5000-6000
The engine is electronic fuel injection system
The engine cooling system shall be water cooled type with Thermostat
The engine is Ultra low emission ratings
The length of engine shaft is 15-20”
The dry weight is more than 75 Kg
The boat shall be inflatable with air pressure by foot pump
The boat is suitable for 7-10 ( Seven to ten ) persons, or for 200 lbs
weight
The exterior size of the boat is min. 4200 mm x 1800 mm
The interior size of the boat is min. 2925 mm x 1000 mm
The diameter of the tube is 19”
The air valves are one way type of approves type and make..
The weight of boat without floor board & OBM is more than 187 lbs.
The boat is supplied with Bow storage bag and repair kit.
Synthetic
Life
jacket
MK-I
(CAT-NIV),
Specification
No.DMSRDE/TEX-4/2005/LJ(B). In appearance, shade and finish and
in other respects ni defined in the specification, the material shall
confirm to the corresponding sealed pattern held in the custody of the
controller CQA 9T&C), Kanpur.
Made from durable high visibility synthetic material maintenance free
Reflective tape provided
Inner dia- 45 cms
Outer dia 70 cms
Floatability- more than 17 kgs
Weight- 2.3 to 3.5 kgs
Photo
Remarks
========================
==================
= =============
===========
=======
====
==
Page 32 of 45
SL /
No
1.
Name of Item
Personal diving
kit
Weight belt
Rate per
Unit
10506.82
Name & address of
the Firms
Joytech, Engineering
& Marketing
Consultants, C-43,
DDA SHEDi, OKHLA
Industrial Area Phase
–I, New Delhi-110020
PROCURED BY BSF
Dive fins
Page 33 of 45
3351.60
Date of AT
and date of
recd by this
unit
24/10/08
07/04/09
Specification
Specification of Weight Belt : Waist belt is made of polypropylene/ nylon fabric and have a quick
release non- breakable buckle of plastic of adjustable size of tightening.
1. Four polypropylene fabric pouched molded to the weight belt to
put weights of 1 Kg (04 Nos ) inside. The pouch opening
independently on top to have button Velcro.
2. The belt is adjustable 30” – 45” range in length, 3 mm thick and
2” broad.
3. Colour : Black
Weight – 1 Kg lead ( 04 numbers )
Specification of Dive Fins
1. Colour - black
2. length – not less than 17”
3. Width – Not less than 4” ( top ) and 8.8” (Bottom). Dimension
tolerance +
4. Material – Thermoplastic rubber / natural rubber. Should not
skid even on a wet metal deck.
5. Hydrodynamic shape – the shape of the fin to facilitate:a) Max Propulsion whilst swimming in water using flutter and
frog kick.
b) Suitable for swimming for long without causing undue.
6. Shoes Pocket;- Pocket should be 7” – 8” deep with an
adjustable back strap ( not less than 1.5 inch in width). Inner
part should be made of soft rubber for use with bare feet. One
additional back strap should be supplied with the fins.
7. Buoyancy: - Approximately 10% negatively buoyant.
Photo
Remarks
2.
Gloves
Model V Lock Brand
Aqualang
128 Nos.
200.00
M/s protos Adventure
Sports & Security
Suppliers Pvt Ltd, B2/47, manu Apartment,
Mayur Vihar New
Delhi-92.
24.10.08
1. Gloves should be made of neoprene
02.04.09
2. The palm of the gloves should be made up of anti slippery
polyurethane
3. Thickness should be not less than 5 mm
4. Gloves should be water proof at a depth of not less than 50 mtrs
24.12.07
DIMENSIONS: A variation of 5% to 10% is acceptable.
Procured by BSF
3.
B A sets light weight
with spare cylinders
(Under Water)
77175.00
M/s Jyotech
Engineering & Mktg
Consultants, H-49, a
\Kalkaji, New Delhi-19.
Procured by BSF
31.03.08
a)
b)
c)
d)
e)
f)
Nominal Capacity of Set
Charging Pressure
Capacity of set after charging
Weight of the set
Weight in water
Cylinders make
8-12 liters
250-300 bars
At least 2400 liters
Not more than 20 Kg
Not more than 03 Kgs
As for as possible to
be Composite material
with unlimited life.
4.
SPECIFICATION
(a)
As far as possible the set to have a wide vision full-face mask.
The straps provided should form a effective seal on to the face.
(b)
Re-breathing of carbon dioxide enriched exhaled air must be
eliminated and the breathing resistance must be as low as possible
whilst the equipment must have sufficient capacity to cater for even an
extremely hard work rate.
(c)
In case the diver does not want to use the full face mask then
the breathing valve with mouth piece should suffice for the use
underwater.
(d)
Mouth piece to have separate inhale and exhale channels so
that the moisture from the diver cannot get deposited in the inlet section
of the breathing valve. This avoids risk of valve freezing in open
positions.
(e)
There should be a mechanism to have a reserve air in the set
and indication to that effect available.
(f)
As far as possible the set should be designed for use in
temperatures range of minus 10 degree Celsius to 50 degree Celsius.
(g)
The set should withstand sea state up to 5
Page 34 of 45
4.
DIVING SUIT
5738/-
M/S Cleghorn &
Company, 34,
Orphangunge Road,
Kidderpore, Kolkata03.
24/12/07
PROCURED BY BSF
5.
Inflatable motor
rescue boats small (
10 seated )
314022.89
M/S Fibroplast, C30, Sector – 58,
Noida, Gautam Budh
Nagar, UP.
procured by BSF
Page 35 of 45
19/07/08
15 Nos
14.02.09
11 Nos
23.02.09
13 Nos
30.04.09
29 Nos
17.05.09
04 Nos
31.05.09
01. The driver wet suit is for use by the divers operating underwater,
which can be easily seen whilst on the surface of water. The basic
design of one piece with sleeves upto the length of arm and the
portion below torso up to ankle level (below knee).
2. The wet suit provided without hood. The suit has a cut designed
to avoid under arm- seams.
3. The lower part of the suit fully covers the legs stopping just above
feet/ankle.
4. The suit is entirely non- magnetic.
5. The diver will able to done the suit very easily and feel
comfortable.
6. The above wet suit is made from macro cellular neoprene.
1. Make- mercury
2. HP-25
3. RPM-5000-6000
4. The engine is electronic fuel injection system
5. The engine cooling system shall be water cooled type with
Thermostat
6. The engine is Ultra low emission ratings
7. The length of engine shaft is 15-20”
8. The dry weight is more than 75 Kg
9. The boat shall be inflatable with air pressure by foot pump
10. The boat is suitable for 7-10 ( Seven to ten ) persons, or for 200 lbs
weight
11.The exterior size of the boat is min. 4200 mm x 1800 mm
12. The interior size of the boat is min. 2925 mm x 1000 mm
13. The diameter of the tube is 19”
14. The air valves are one way type of approves type and make..
15. The weight of boat without floor board & OBM is more than 187 lbs.
16. The boat is supplied with Bow storage bag and repair kit.
6.
High Pressure
Breathing Air
Compressor
498690.40
M/s Joseph Leslie
Drager, MFG Pvt Ltd.,
Leslie House Prof. VS
Agashe Road, Dadar
West Mumbai-
21.10.09
04.01.10
Procured by CISF
01. GENERAL DIMENSIONS :i. The set is lightweight, rugged & trans- portable (with lockable
wheels) & weight up to 175 Kg.
ii. Operating Pressure 300 to 200 bar and able to fill cylinders at 300
bar as well as 200 bar (or any pressure between 300 to 200 bar) by
simply selecting/setting the pressure setting on a pressure switch on
the compressor.
iii. Charging rate 9 cfm (+/-5%) for standard international filling norm.
03. GENERAL FEATURES :i.
Compact, robust, not require any foundation.
ii.
Design ensures minimum wearing of components and ease of
maintenance.
iii. Filtration system intake and at final point of use to ensure highest
level of purity of air delivered and to ensure that the quality of
breathing air is as per EN 12021 or CGA-E or any equivalent
international standard for Breathing Air. The firm furnish test
certificate from Govt. Approved/international or equivalent.
iv. Provision for full range of automated control devices to monitor both
compressor and working conditions should be provided. The
compressor should have noise up to 8f5 dB at 1M distance. The
control panel on the compressor has the START, STOP and
EMERGENCY STOP button. The panel have pressure switch where
the user can select level of pressure at switch he wants to fill the
cylinder.
The compressor stop when desired pressure is reached i.e. the
compressor has the feature of AUTO STOP‟. The compressor also
have feature of AUTO DRAIN of the moisture in the system and it
should get drained at regular intervals. The disposal of the drain
pollution free in a tank. The compressor has inter stage control
device and final stage pressure gauge for the operator to monitor.
The compressor also has OIL LEVEL INDICATOR.
v. Eco friendly condensate collection.
vi. Construction modular type.
vii. Machine is electric driven suitable for 3 phase 400-440 V 50 HZ
supply.
7.
1. Under water
communication set
(wireless)
355500.00
140625.00
Under water
communication set
(wired)
Page 36 of 45
M/s Jyotech
Engineering & Mktg
Consultant, H-49 A,
Kalkaji, New Delhi-19.
-doProcured by BSF
06.10.09
07-08-10
-do-
a.
b.
c.
Weight of Diving Unit – within 1 Kg + 10%
Diver Unit pressure compensated 10 Mtrs + 10%
Weight of Surface Panel within 6 Kgs + 10
8.
Under water torch
41,512/-
M/s Audo Viso E-48,
nd
(2 Floor, Connaught
place, New Delhi-01.
Procured by BSF
Page 37 of 45
13-11-09
09-03-10
06-05-10
1. The torch has integrated handle for ease of under water handling.
2. The diver lamp search system is self contained with its own in built
re - Chargeable battery pack.
3. The torch is well insulated.
4. Lanyard and carabineer is provided for attaching it with belt.
5. It has safety mechanism to prevent accidental short circuit.
6. Weight – 1200 Gms.
6. Torch operates upto the depth of 10 Mtr in water.
7. Battery charging time – 05 Hours
8. Torch work at least two hour.
9. The torch is able to illuminate the object placed under water at two
meter distance from torch.
========================
==================
= =============
===========
=======
====
==
Page 38 of 45
Sl/
No.
Name
1.
Rate per
unit
326583.89
Name and
address of the
firm
M/S Fibroplast, C30, Sector – 58,
Noida, Gautam
Budh Nagar, UP.
Date of at
and date of
received by
this unit
19/07/08
04 NOS
23/02/09
procured by BSF
Inflatable Boat with
OBM
2.
411534.64
Fibre reinforced
Plastic Boats
M/S Poly Glass
Fibre Industries
Pvt Ltd, 265,
Okhla Industrial
Estate, New Delhi110020
procured by BSF
19/05/08
02 NOS
26/09/08
02 NOS
03/12/08
02 NOS
03/12/08
02 NOS
17/03/09
Page 39 of 45
02 NOS
23/03/09
Specification
made mercury
HP-25
RPM-5000-6000
The engine is electronic fuel injection system
The engine cooling system shall be water cooled type with
Thermostat
The engine is Ultra low emission ratings
The length of engine shaft is 15-20”
The dry weight is more than 75 Kg
The boat shall be inflatable with air pressure by foot pump
The boat is suitable for 7-10 ( Seven to ten ) persons, or for 200
lbs weight
The exterior size of the boat is min. 4200 mm x 1800 mm
The interior size of the boat is min. 2925 mm x 1000 mm
The diameter of the tube is 19”
The air valves are one way type of approves type and make..
The weight of boat without floor board & OBM is more than 187
lbs.
The boat is supplied with Bow storage bag and repair kit.
1. Make – Fibre Glass Rescue Boat – India
2. Brand – OBM- MARINER 40 HP Four Stroke ( USA )
3. The FRP Rescue boat is designed for carry 10 persons plus a
crew of two, i.e a carriage capacity of 12 men or 1200 Kgs. The
weight of the boat is within 350 Kgs excluding weight of OBM
and Accessories. The free board at full load is not less than 12
inches. The length , width and height of the boat is not less than
15 feet, 6 feet and 2.5 respectively
4. The ignition system is Electronic Digital Inductive type
5. There has alternator of 18 Amp & 223 watts.
The steering system is remote type with console at the front.
Photo
Remarks
3.
43, 312.5
Portable Oxygen
Breathing Unit
4.
M/S Udyogi Plastic
(P) Limited, 294,
B.B. Ganguly
Street, 2nd floor,
Kolkatta-12.
18.08.08
(date of
supply
order)
02.12.08
Procured by SB Ftr
BSF
2,50,000
Motor Operated
Multi cable winch
M/S Ageis Health
Care, Suit No 1,
Second Floor,
Parmeshwari,
Chhatribarib
Road, Ghty
15/06/09
16/02/10
Procured by CISF
Material have adequate mechanical strength,
durability and resistance to detoriation by heat or
by contact with sea water or plain water
Parts are easy to clean, examination and testing
Weight shall not exceed 14 kgs.
Leak proof on joints
Face mask is made up of either neopropane or
silicon.
Face mask cover eyes ,nose ,mouth and chin.
Pressure gauge range 0-350 bars.
The Multi cable winch should be required for small rescue
work, the 4 to 5 hp rated motor, which should provide at least
pulling power of 5 tons. It should have line retrieval speed not
less than 6 meters/minutes at full pull. This compact winch
shall complete with handle/mounting system for a class III two
inch receiver, hawse, fairlead, remote control with minimum
3.6 meters, free spool clutch and battery cable with mounting
kits.
5.
49799.50
Generator sets 2.5
KVA (Honda)
M/s D R Brij Mohan
& Sons Pvt ltd, G S
Road, Bhangagarh
Ghty ( Ph. No.
0361-2529416;
2529257
DGSND contract
avail
31.08.07
(date of
supply
order)
03.09.07
Rated output -2100 -2300watt
Max output – 2400-2600 Watt
Fuel – kerosene/petrol
Rated current – 10.5 amp
Rated voltage – 220Volts
Rated frequency – 50 Hz
Dc output – 8.3 Amp
Dimension – 605 x 425 x 550 mm
Page 40 of 45
Dry wt – 60to65 kgs
Engine type – 4 strokes, 1 cylinder
Cooling system- forced air cooling
Oil capacity – 1 to1.5 ltrs
Fuel tank capacity – 12 to15 ltrs
6.
229500/-
High Pressure
Pumps
M/s Inventa
Cleantec Pvt Ltd,
C-31, Sector-63
Noida-201301,
Gautam
Budhnagar, UP
Weight (filled and fuelled) – not more than 250 kg
Tank capacity- 100 ltrs
Water delivered – 23ltrs/min
Nozzle pressure- 100 bar
Range 10 mtr(solid stream) & 6 mtr( water mist)
Procured by Prov
Dte ( Proc Cell)
FHQ, BSF
Length of hose- 60mtr
Pump –rpm 1000 to 1500
Power of engine – 9.5 KW petrol driven
7.
2672.00
Rubber Suits
M/s Joseph leslie &
Co. Leslie House 3rd
floor Proof V S
Agshe Road off 87C, Bhawani
Shankar, Road,
Dadar, West
Mumbai
Procured by Prov
Dte ( Proc cell )
FHQ,BSF
Page 41 of 45
14/08/07
28/12/07
1. Used for protection of the wearer against acid and
alkali splashes in chemical, fertilizers and
pharmaceutical material.
2. Made of high quality PVC
8.
Tractor with
attachments and
trolley
to be
procured
by Prov
Dte ( Proc
cell)
to be procured by
Prov Dte ( Proc
cell)
-
9.
119250.00
Floating Pumps
M/s Newage
industrial 7,
Champaklal
Udyog Bhawan
Sion (East)
Mumbai- 22
30/07/08
10/03/09
Procured by Prov
Dte ( Proc cell )
FHQ, CRPF
10.
Not yet procured
 For the purpose of Fire Fighting and rescue operations.
Light weight, reliable, self priming pump that floats,
discharges water @ at least 180 ltr/ min.
 Casing : anodized Aluminum
 Impeller : Bronze impeller
 Water resistant air cleaner and muffler.
 6 to 8 hp or more, air cooled.
 Recoil starter with handle
 Solid state ignition
 Use unleaded gasoline/ Petrol and oil mixed
 Minimum 2 years parts and service warranty
 Automatic float controlled throttle
 Compression release valve for easier starts
Dry weight is not more than 30 Kgs.
Dimension –not more than 580x440x520mm
179168/-
Inflatable lighting
tower
M/s Aska
Equipments
Limited, Aska
House “
Gargashraya” 193
Deepali, Deepali
Chowk, Pitampura,
New Delhi-34
DGS&D supply
25.06.07
Wt- 50 kg
30/07/07
Total height-3-5 mtr
Light source- 400watt
Illuminating area- 10000 sq mtr
Brightness- 4000 lumen
Generator -4 stroke engine(petrol), capacity-1200 va
Tank capacity- not less than 7 ltrs
Page 42 of 45
Not Available
11.
Portable shelter
10’ x 14’ & 7’
144112.00
M/s Calcutta
commercial
corporation, 365
Sultanpur,
Mehrauli- New
Delhi
Procured by
DIG(P) Prov
Compleas,
Guwahati and
supplied to this unit
Page 43 of 45
11.06.08
12.08.08
1.
The portable shelter should be easy to set up.
2.
It is should be simplex, no framework and structure
should be involved. The integral floor should set the
dimensions of the shelter automatically on set up. Anchoring
and guys will simply keep it in place during strong winds.
3.
It should be lightweight so that 2 people can easily
lift it.
4.
Material should stay clean and dry and shall not
absorb spills, improving hygiene.
5.
Shelter walls open up from inside if fast escape shall
be required.
6.
The shelter should be totally weather resistant and
keeps the occupants clean, dry and warm in high winds, cold
temperatures, driving rain and heavy snow.
7.
The rigid wall panels should be supported significant
weight for organizing and storing the possessions of a family in
temporary circumstance with hangers and shelves.
8.
The double walled panel should be insulation at
least „R‟ factor of 1.4, allowing the shelter should be heated
and cooled efficiently.
9.
The while roof section should be allowed ample light
transmission, giving the interior an airy and spacious
atmosphere.
10.
When lit from the inside at night, the maternal
should be opaque enough to give privacy and the while interior
allows efficient use of the light source.
11.
Any flat panel should have a hole or flap cut into it by
the occupant for
exhaust ducting, water supply lines, drain
pipes, extra ventilation etc.
12.
The portable shelter should be repairable easily and
permanently with duct tape.
13.
Shelter should be moved with whole set up and with
in tenor contents in place. This allows easy reorganization of
established encampments if a road allowance needs to be
widened or a drainage ditch needs to be widened or a
drainage ditch needs to be constructed with a change in
seasons.
14.
The material used for the fabrication of shelter
should be polypropylene.
15.
The weight of the shelter (10‟ X 23‟ X 7‟) should not
be more than 65 Kg.
12.
Portable shelter
10’x23’x7’
2,08,000.00
M/s Calcutta
commercial
corporation, 365
Sultanpur,
Mehrauli- New
Delhi
Procured by
DIG(P) Prov
Compleas,
Guwahati and
supplied to this unit
11.06.08
12.08.08
1. The portable shelter should be easy to set up.
2. It is should be simplex, no framework and structure should be
involved. The integral floor should set the dimensions of the
shelter automatically on set up. Anchoring and guys will simply
keep it in place during strong winds.
3. It should be lightweight so that 2 people can easily lift it.
4. Material should stay clean and dry and shall not absorb spills,
improving hygiene.
5. Shelter walls open up from inside if fast escape shall be
required.
6. The shelter should be totally weather resistant and keeps the
occupants clean, dry and warm in high winds, cold
temperatures, driving rain and heavy snow.
7. The rigid wall panels should be supported significant weight for
organizing and storing the possessions of a family in
temporary circumstance with hangers and shelves.
8. The double walled panel should be insulation at least „R‟ factor
of 1.4, allowing the shelter should be heated and cooled
efficiently.
9. The while roof section should be allowed ample light
transmission, giving the interior an airy and spacious
atmosphere.
10. When lit from the inside at night, the maternal should be
opaque enough to give privacy and the while interior allows
efficient use of the light source.
11. Any flat panel should have a hole or flap cut into it by the
occupant for
exhaust ducting, water supply lines, drain
pipes, extra ventilation etc.
12. The portable shelter should be repairable easily and
permanently with duct tape.
13. Shelter should be moved with whole set up and within tenor
contents in place. This allows easy reorganization of
established encampments if a road allowance needs to be
widened or a drainage ditch needs to be widened or a
drainage ditch needs to be constructed with a change in
seasons.
14. The material used for the fabrication of shelter should be
polypropylene.
15. The weight of the shelter (10‟ X 23‟ X 7‟) should not be more
than 65 Kg.
16.
Page 44 of 45
Page 45 of 45