BRW4 Bruno Wall I/D Indirect-Direct T8 Spec Sheet

advertisement
Type: ________________________
Bruno Wall I/D
Project: ______________________
Indirect-Direct T8
SCEP Option
Wall Mount
S P E C I F I C AT I O N S
BRW4
__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________
LAMPING OPTIONS
BRW4 - 1
BRW4 - 2
1 3⁄4”
1
1 3⁄4”
⁄2”
⁄2”
1
8 1⁄4”
8 1⁄4”
SPECIFICATIONS
Construction
Nominal 8 1⁄4” x 1 3⁄4” rectangular housing is formed
from cold-rolled steel. Die-cast end caps are
mechanically attached with no exposed fasteners.
perforated blade or white painted, perforated blade.
Each available with optional acrylic opal overlay.
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.
Finish
Luminaire Length
Fine-textured, white polyester powder paint
standard. Drop pan always C110 painted
aluminum finish. Consult factory for special finish
requirements.
Reflectors
Die-formed white painted reflector.
Shielding /Baffle
Choose one of four parabolic baffle options:
semi-specular, white painted, semi-specular
4’ 1⁄16”, 8’ and 12’ lengths in a single section. For
total luminaire length, add 5⁄8” for each flat end cap
and 4” for each sculptured end cap. Using internal
joiners, 4’, 8’ and 12’ sections can be joined to form
longer rows.
Electrical
Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
CATALOG NUMBER
Examples:
__________
BRW4 2 32 WHR SPB 12FT R8 120 GEB10 SCT LP830 C210
__________
__________
__________
Luminaire # of Lamps Lamp Type
Reflector
in Cross
BRW4
32
32W T8 WHRWhite
Section
reflector
__________
__________
_________
__________
__________
__________
Shielding
Baffle
Ballast Type
SSB Semi specular
WPB White painted
SSP Semi specular
perforated blade
WPP White painted
perforated blade
Maximum
Section Length
Voltage
(Blank)
OPD Opal overlay
Luminaire
Row
Length
120
277
347
GEB10 <10% THD Electronic
ADEZ1 Advance Mark 10 dim
DMHL3D1 Lutron Hi-Lume dim
ADZT1Advance Mark 7 0-10V dim
1
2
______________
# of Emergency
Modules
(Blank)None
1SE
1 section
2SE 2 sections
XSE X sections
X FT
(4’ increments)
R4
R8
R12
4’ section(s)
8’ section(s)
12’ section(s)
Reference Ballast Wizard on website
or consult factory for other options.
________________
________________
________________
______________
_________________________________
Emergency Type2
Switching
Lamp Color
Finish
Options
(Blank)None
EC
Emergency circuit
EL1
Emergency battery pack
EN1
Emergency battery pack
w/night light circuit
SCT
DCT
L/LP No lamp
L/LPENo lamp. Wired for energy
saving lamps.
LP830 3000K 80+ CRI
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI
C110
DL
DU
ELH
ELS
Single circuit
Dual circuit
Painted aluminum
(low gloss)
C210 White white
(fine-textured
low gloss)
C099 Custom finish
Reference Lamp Chart on website or
consult factory for other options.
Damp location label
Dust cover
Emergency through wiring w/separate feed
Emergency through wiring w/single feed,
shared neutral
ELS2 Emergency through wiring w/single feed,
separate neutrals
GLR Fusing (fast blow)
GMF Fusing (slow blow)
NYC New York City code
SCEP Sculptured end cap
Notes:
1 Not available in 347V
2 Emergency type is installed in last 4’ of luminaire sections.
Separate feed required unless ELS or ELS2 is specified
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: techsupport@peerlesslighting.com • PeerlessLighting.com
© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Peerless Bruno” are registered trademarks of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx
BRW4 Bruno Wall I/D
Indirect-Direct T8
1
Bruno Wall I/D
Type: ________________________
Project: ______________________
Indirect-Direct T8
Wall Mount
BRW4
MOUNTING DETAIL
2 x 4 switch box
— by others
feed cover
2 13⁄16"
mounting
bracket
feed cover
mounting holes for
1
⁄4" bolt
⁄16"
⁄4"
11
3
mounting bracket
(2) #10-24 mounting screws
1 1⁄2 "
to bottom of housing
⁄4 "
3
10"
(2)1⁄4 " diameter mounting bolts
— by others
WEIGHTS & SUPPORT SPACING
STANDARD SECTIONS
2 13⁄16”
typical
Key:
⁄8” standard flat end caps
4” optional sculptured end caps
5
2’-8”
16 LBS
Support location
Standard feed location
EM feed location
•
4’-1 ⁄16” O.A.
5
3’-4”
34 LBS
3’-4”
8’-1 1⁄4” O.A.
4’-0”
2’-8”
4’-0”
55 LBS
12’-1 1⁄4” O.A.
ELEVATION
CONFIGURATIONS
Tenon inside, outside and straight connectors available for wall configurations.
Reference Pattern Connector Guide for additional details.
PHOTOMETRICS
Actual performance may differ as a result of end-user environment and application.
1-LAMP T8
83.4% efficiency
2377 delivered lumens
2-LAMP T8
67.9% efficiency
3871 delivered lumens
61.7% up / 38.3% down
57.6% up / 42.4% down
1-LAMP T8 WITH OPD
84.0% efficiency
2393 delivered lumens
2-LAMP T8 WITH OPD
67.4% efficiency
3840 delivered lumens
75.1% up / 24.9% down
72.6% up / 27.4% down
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: techsupport@peerlesslighting.com • PeerlessLighting.com
© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Peerless Bruno” are registered trademarks of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx
BRW4 Bruno Wall I/D
Indirect-Direct T8
2
Download