Bruno Wall
Type: ________________________
Project: ______________________
Indirect
Indirect T8
SCEP Option
Wall Mount
S P E C I F I C AT I O N S
BRW1
__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________
LAMPING OPTIONS
BRW1 - 1
BRW1- 2
1 3⁄4”
1 3⁄4”
8 1⁄4”
8 1⁄4”
SPECIFICATIONS
Construction
Finish
Reflectors
Electrical
Nominal 8 1⁄4” x 1 3⁄4” rectangular housing is formed
from cold-rolled steel. Die-cast end caps are
mechanically attached with no exposed fasteners.
Die-formed white painted reflector.
Luminaire Length
Fine-textured, white polyester powder paint
is standard. Consult factory for special finish
requirements.
4’ 1⁄16”, 8’ and 12’ lengths in a single section. For
total luminaire length, add 5⁄8” for each flat end cap
and 4” for each sculptured end cap. Using internal
joiners, 4’, 8’ and 12’ sections can be joined to form
longer rows.
Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.
CATALOG NUMBER
Examples:
__________
BRW1 2 32 WHR 40FT R8 120 GEB10 DCT LP835 C210 SCEP — BRW1 2 32 WHR 32FT R8 277 GEB10 1SE EL DCT LP835 C110
__________
Luminaire # of Lamps in
Cross Section
BRW1
__________
__________
_________
__________
__________
__________
__________
Lamp Type
Reflector
Ballast Type
# of Emergency Modules
WHRWhite
reflector
Maximum
Section Length
Voltage
32
Luminaire Row
Length
X FT
(4’ increments)
R4
R8
R12
120
277
347
GEB10 <10% THD Electronic
ADEZ1 Advance Mark 10 dim
DMHL3D1 Lutron Hi-Lume dim
ADZT1Advance Mark 7 0-10V dim
(Blank)None
1SE
1 section
2SE 2 sections
XSE X sections
32W T8
1
2
4’ section(s)
8’ section(s)
12’ section(s)
Reference Ballast Wizard on website
or consult factory for other options.
________________
________________
______________
_________________________________
Emergency Type2
______________
Switching
Lamp Color
Finish
Options
(Blank)None
EC
Emergency circuit
EL1
Emergency battery pack
EN1
Emergency battery pack
w/night light circuit
SCT
DCT
L/LP No lamp
L/LPENo lamp. Wired for energy
saving lamps.
LP830 3000K 80+ CRI
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI
C110
DL
DU
ELH
ELS
ELS2
GLR
GMF
NYC
SCEP
Single circuit
Dual circuit
Reference Lamp Chart on website or
consult factory for other options.
Painted aluminum
(low gloss)
C210 White white
(fine-textured
low gloss)
C099 Custom finish
Damp location label
Dust cover
Emergency through wiring w/separate feed
Emergency through wiring w/single feed, shared neutral
Emergency through wiring w/single feed, separate neutrals
Fusing (fast blow)
Fusing (slow blow)
New York City code
Sculptured end cap
Notes:
1 Not available in 347V
2 Emergency type is installed in last 4’ of luminaire sections.
Separate feed required unless ELS or ELS2 is specified
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: techsupport@peerlesslighting.com • PeerlessLighting.com
© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Peerless Bruno” are registered trademarks of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx
BRW1 Bruno Wall
Indirect T8
1
Bruno Wall Indirect
Type: ________________________
Project: ______________________
Indirect T8
Wall Mount
BRW1
MOUNTING DETAIL
2 x 4 switch box
— by others
feed cover
2 13⁄16"
mounting
bracket
feed cover
mounting holes for
1
⁄4" bolt
⁄16"
⁄4"
11
3
mounting bracket
(2) #10-24 mounting screws
1 1⁄2 "
to bottom of housing
⁄4 "
3
10"
(2)1⁄4 " diameter mounting bolts
— by others
WEIGHTS & SUPPORT SPACING
STANDARD SECTIONS
2 13⁄16”
typical
Key:
⁄8” standard flat end caps
4” optional sculptured end caps
5
2’-8”
16 LBS
Support location
Standard feed location
EM feed location
•
4’-1 ⁄16” O.A.
5
3’-4”
34 LBS
3’-4”
8’-1 1⁄4” O.A.
4’-0”
2’-8”
4’-0”
55 LBS
12’-1 1⁄4” O.A.
ELEVATION
CONFIGURATIONS
Tenon inside, outside and straight connectors available for wall configurations.
Reference Pattern Connector Guide for additional details.
PHOTOMETRICS
Actual performance may differ as a result of end-user environment and application.
1-LAMP T8
61.1% efficiency
1742 delivered lumens
2-LAMP T8
65.8% efficiency
3748 delivered lumens
100.0% up / 0.0% down
100.0% up / 0.0% down
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: techsupport@peerlesslighting.com • PeerlessLighting.com
© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Peerless Bruno” are registered trademarks of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx
BRW1 Bruno Wall
Indirect T8
2