INSTALLATION INSTRUCTIONS
Model:
PASSAGE
Fixture Family:
OW2482, OW2486
Document Description: Installation Instructions for
Passage Series Luminaires
1717 West Civic Drive Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© Visa Lighting
SHEET 2: 2x4 JUNCTION BOX WITH RECTANGULAR
TRANSITION PLATE
SHEET 3: 2x4 JUNCTION BOX WITH ROUND
TRANSITION PLATE
Sheet: 1 of 5
SHEET 5: OCTAGON JUNCTION BOX
(WITH JUNCTION BOX COVER)
Rev: B
SHEET 4: 2x4 STANDARD JUNCTION BOX
Drawing: 762027XX
TABLE OF CONTENTS
Eng: CLD
Date Drawn: 06/01/15
*NOTE: INSTALLATION INSTRUCTIONS ARE FOR 3FT AND 6FT VERSIONS
3FT FIXTURE SHOWN
!
When using electrical equipment, basic safety precautions should always be followed, including the following:
• Read all instructions carefully before installing and save for future use.
• Make sure all connections are in accordance with the National Electrical Code and local regulations.
• To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture
• Service should be performed by qualified personnel.
• These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.
INSTALLATION INSTRUCTIONS
Model:
PASSAGE
Fixture Family:
OW2482, OW2486
Document Description: Installation Instructions for
Passage Series Luminaires
1717 West Civic Drive Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© Visa Lighting
MOUNTING BRACKET
(Already attached to
J-Box mounting plate)
MOUNTING SURFACE
JUNCTION BOX
(BY OTHERS)
#8 SET SCREW
(3), (4) ON THE
6FT VERSION
Drawing: 762027XX
2X4 TRANSITION RCT (JBC)
Rev: B
Sheet: 2 of 5
FIXTURE HOUSING
4.
5.
6.
Loosen #8 set screws (3), (4) #8 set screws on the 6ft version.
Remove fixture housing from mounting bracket and J-Box adapter plate.
Mount J-Box adapter plate to mounting surface using thread forming screws (4),
(8) for the 6ft version, (by others) being careful not to pinch wires.
Make all electrical connections per code.
Be careful not to pinch wires and re-secure fixture to mounting bracket on wall.
Tighten #8 set screws.
For proper wet seal, provide a continuous bead of caulk or silicone at mounting plate when
mounting surface is not smooth.
!
When using electrical equipment, basic safety precautions should always be followed, including the following:
• Read all instructions carefully before installing and save for future use.
• Make sure all connections are in accordance with the National Electrical Code and local regulations.
• To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture
• Service should be performed by qualified personnel.
• These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.
Date Drawn: 06/01/15
1.
2.
3.
THREAD FORMING
SCREWS (4), (8) ON THE
6FT VERSION
(by others)
Eng: CLD
J-BOX MOUNTING
PLATE
INSTALLATION INSTRUCTIONS
Model:
PASSAGE
Fixture Family:
OW2482, OW2486
Document Description: Installation Instructions for
Passage Series Luminaires
1717 West Civic Drive Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© Visa Lighting
2X4 TRANSITION RND (JBC)
#8 SET SCREW
(3), (4) ON THE
6FT VERSION
MOUNTING PLATE
(Already attaached to
J-Box mounting plate)
JUNCTION BOX
(BY OTHERS)
Drawing: 762027XX
MOUNTING SURFACE
Rev: B
Sheet: 3 of 5
Eng: CLD
J-BOX MOUNTING
PLATE
THREAD FORMING
SCREWS (4), (8) ON THE
6FT VERSION
(by others)
1.
2.
3.
4.
5.
6.
Loosen #8 set screws (3), (4) #8 set screws on the 6ft version.
Remove fixture housing from mounting bracket and J-Box adapter plate.
Mount J-Box adapter plate to mounting surface using thread forming screws (4),
(8) for the 6ft version, (by others) being careful not to pinch wires.
Make all electrical connections per code.
Be careful not to pinch wires and re-secure fixture to mounting bracket on wall.
Tighten #8 set screws.
For proper wet seal, provide a continuous bead of caulk or silicone at mounting plate when
mounting surface is not smooth.
!
When using electrical equipment, basic safety precautions should always be followed, including the following:
• Read all instructions carefully before installing and save for future use.
• Make sure all connections are in accordance with the National Electrical Code and local regulations.
• To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture
• Service should be performed by qualified personnel.
• These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.
Date Drawn: 06/01/15
FIXTURE HOUSING
INSTALLATION INSTRUCTIONS
Model:
PASSAGE
Fixture Family:
OW2482, OW2486
Document Description: Installation Instructions for
Passage Series Luminaires
1717 West Civic Drive Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© Visa Lighting
2X4 STANDARD (JBC)
MOUNTING SURFACE
JUNCTION BOX
(BY OTHERS)
Rev: B
#8 SET SCREW
(3), (4) ON THE
6FT VERSION
Drawing: 762027XX
MOUNTING PLATE
(Already attached to
J-box mounting plate)
Sheet: 4 of 5
Eng: CLD
J-BOX MOUNTING
PLATE
FIXTURE HOUSING
1.
2.
3.
4.
5.
6.
Loosen #8 set screws (3), (4) #8 set screws on the 6ft version.
Remove fixture housing from mounting bracket and J-Box adapter plate.
Mount J-Box adapter plate to mounting surface using thread forming screws (4),
(8) for the 6ft version, (by others) being careful not to pinch wires.
Make all electrical connections per code.
Be careful not to pinch wires and re-secure fixture to mounting bracket on wall.
Tighten #8 set screws.
For proper wet seal, provide a continuous bead of caulk or silicone at mounting plate when
mounting surface is not smooth.
!
When using electrical equipment, basic safety precautions should always be followed, including the following:
• Read all instructions carefully before installing and save for future use.
• Make sure all connections are in accordance with the National Electrical Code and local regulations.
• To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture
• Service should be performed by qualified personnel.
• These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.
Date Drawn: 06/01/15
THREAD FORMING
SCREWS (4), (8) ON THE
6FT VERSION
(by others)
INSTALLATION INSTRUCTIONS
Model:
PASSAGE
Fixture Family:
OW2482, OW2486
Document Description: Installation Instructions for
Passage Series Luminaires
1717 West Civic Drive Milwaukee, WI 53209
414-354-6600
Design Modification Rights Reserved
© Visa Lighting
OCTAGON (JBC)
#8 SET SCREW
(3), (4) ON THE
6FT VERSION
Drawing: 762027XX
MOUNTING SURFACE
MOUNTING BRACKET
(Already attached to
J-Box mounting plate)
JUNTION BOX
(BY OTHERS)
Rev: B
Sheet: 5 of 5
FIXTURE HOUSING
1.
2.
3.
4.
5.
6.
Loosen #8 set screws (3), (4) #8 set screws on the 6ft version.
Remove fixture housing from mounting bracket and J-Box adapter plate.
Mount J-Box adapter plate to mounting surface using thread forming screws (4),
(8) for the 6ft version, (by others) being careful not to pinch wires.
Make all electrical connections per code.
Be careful not to pinch wires and re-secure fixture to mounting bracket on wall.
Tighten #8 set screws.
For proper wet seal, provide a continuous bead of caulk or silicone at mounting plate when
mounting surface is not smooth.
!
When using electrical equipment, basic safety precautions should always be followed, including the following:
• Read all instructions carefully before installing and save for future use.
• Make sure all connections are in accordance with the National Electrical Code and local regulations.
• To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture
• Service should be performed by qualified personnel.
• These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting.
Date Drawn: 06/01/15
THREAD FORMING
SCREWS (4), (8) ON THE
6FT VERSION
(by others)
Eng: CLD
J-BOX MOUNTING
PLATE