1.
2.
3.
4.
5.
ALL FLOOR DRAINS AND FLOOR SINKS MUST HAVE TRAP PRIMERS. PROVIDE INVERTED TEE
CONNECTION FROM SINK TAILPIECE OR FLUSH VALVE TYPE TRAP PRIMER CONNECTION TO
ALL FLOOR DRAINS, FLOOR SINKS AND HUB DRAINS. AS LAST RESORT PROVIDE
MECHANICAL TYPE TRAP PRIMER (PPP INC. "OREGON #1" TYPE). CONNECT TO NEAREST
WATER SERVING THAT AREA PER MANUFACTURER'S INSTALLATION INSTRUCTIONS. IN
JURISDICTIONS WHERE PRESSURE ACTIVATED MECHANICAL PRIMERS ARE NOT ALLOWED,
USE ELECTRONIC TRAP PRIMERS. COORDINATE POWER REQUIREMENTS WITH ELECTRICAL
CONTRACTOR. PROSET "TRAP GUARD" DEVICE MAY BE USED IN LIEU OF TRAP PRIMERS
WHEN ALLOWED BY LOCAL CODE AUTHORITY HAVING JURISDICTION. BEFORE USING
PROSET "TRAP GUARD" CONTRACTOR MUST OBTAIN WRITTEN APPROVAL FROM LOCAL
CODE AUTHORITY HAVING JURISDICTION AND PROVIDE COPIES TO ARCHITECT AND
ENGINEER.
A.
B.
C.
PIPING SIZE FOR WATER MAIN DROPS AND MANIFOLD IN CHASE OR WALL TO REMAIN FULL
SIZE OF DROP INDICATED. REFERENCE FIXTURE CONNECTION SCHEDULE FOR INDIVIDUAL
LINE SIZE TO EACH FIXTURE.
COORDINATE ALL WASTEWATER FLOOR PENETRATIONS AND PIPING PENETRATIONS WITH
STRUCTURAL PRIOR TO INSTALLATION. PIPING MAY BE OFFSET SLIGHTLY TO AVOID
STRUCTURAL CONFLICTS.
ROUTE VENT FROM EACH FIXTURE TO HORIZONTAL VENT HEADER IN CHASE/WALL OR TO
NEAREST COMMON VTR ABOVE CEILING. REFERENCE FIXTURE CONNECTION SCHEDULE
FOR INDIVIDUAL FIXTURE VENT SIZES. VENT HEADERS IN CHASE TO BE SIZED
ACCORDINGLY: 1 1/2" VENT UP TO 6 DRAIN FIXTURE UNITS MAXIMUM DEVELOPED LENGTH
OF 60 FEET (EXCEPT FOR WATER CLOSETS), 2" VENT UP TO 20 DRAIN FIXTURE UNITS
MAXIMUM DEVELOPED LENGTH OF 120 FEET, 3" VENT UP TO 84 DRAIN FIXTURE UNITS
MAXIMUM DEVELOPED LENGTH OF 212 FEET AND 4" VENT UP TO 256 DRAIN FIXTURE UNITS
MAXIMUM DEVELOPED LENGTH OF 300 FEET. BRANCH VENTS EXCEEDING 40 FEET IN
DEVELOPED LENGTH ARE TO BE INCREASED BY ONE PIPE SIZE. NO MORE THAN 1/3 OF THE
CODE PERMITTED DEVELOPED LENGTH SHALL BE IN HORIZONTAL POSITION. EXTEND
COMMON VENT UP THROUGH ROOF.
ROUTE ALL VENTS TO NEAREST COMMON VENT THRU ROOF (VTR) TO MINIMIZE ROOF
PENETRATIONS. VTR TO BE MINIMUM 15 FEET AWAY FROM OUTSIDE AIR INTAKES.
COORDINATE WITH MECHANICAL CONTRACTOR PRIOR TO INSTALLATION.
D.
E.
CONTRACTORS TO REVIEW AND COMPARE ALL DRAWINGS SO ALL WORK IN THEIR
RESPECTIVE TRADE IS INCLUDED IN BID. EACH CONTRACTOR SHALL INCLUDE ALL
MATERIALS AND INSTALLATION REQUIRED FOR HIS PARTICULAR TRADE AFTER
COMPLETE REVIEW OF ALL CONTRACT DRAWINGS AND SPECIFICATIONS.
ALL WORK SHALL COMPLY WITH THE APPLICABLE LOCAL, STATE AND FEDERAL CODES
AND ORDINANCES. FOLLOW RECOMMENDED PRACTICES AS SET DOWN BY ASME,
SMACNA, ASHRAE, NFPA, APPLICABLE BUILDING CODE, APPLICABLE MECHANICAL CODE,
APPLICABLE PLUMBING CODE, NATIONAL ELECTRICAL CODE, AGA, ADA AND OSHA, AS
THEY APPLY TO THIS PROJECT EXCEPT IN CASES WHERE LOCAL STATUTES GOVERN.
THE CONTRACTOR SHALL VERIFY WITH AUTHORITY HAVING JURISDICTION THE LATEST
ADOPTED LOCAL CODES, ORDINANCES AND AMENDMENTS THAT APPLY TO THIS
PROJECT. PROVIDE CONDENSATE DISPOSAL POINT FOR ALL MECHANICAL EQUIPMENT
TO CODE APPROVED DISPOSAL. COORDINATE WITH MECHANICAL CONTRACTOR.
ABSOLUTELY NO PIPING OR DUCTWORK CAN BE ROUTED ABOVE ELECTRICAL PANELS,
GEAR OR TRANSFORMERS. THE ONLY HVAC, PLUMBING, SPRINKLER OR DUCTWORK
THAT CAN ENTER AN ELECTRIC ROOM ARE THOSE SPECIFICALLY SERVING THAT ROOM.
THESE SERVICES CAN ONLY ENTER INTO ELECTRIC ROOM ABOVE ENTRY DOOR.
F.
PROVIDE VALVE TAGS FOR ALL VALVES. PROVIDE CEILING ACCESS MARKERS FOR
VALVES LOCATED ABOVE CEILING OR BEHIND WALL MOUNTED PANEL.
G.
PLUMBING PIPING SHALL NOT BLOCK ACCESS TO EQUIPMENT, JUNCTION BOXES,
DISCONNECTS, ACCESS DOORS, ETC.
H.
ALL VALVES ARE TO BE ACCESSIBLE AND SHALL NOT BE LOCATED MORE THAN FOUR
FEET ABOVE THE CEILING.
I.
CONTRACTOR TO CONNECT COLD WATER, TEMPERED WATER, WASTE WATER AND
VENT PIPING TO ALL FIXTURES PER MANUFACTURER'S RECOMMENDATIONS, UNLESS
OTHERWISE NOTED ON DRAWINGS.
J.
BEFORE ANY CUTTING OR TRENCHING OPERATIONS BEGIN, VERIFY WITH OWNER'S
REPRESENTATIVE, UTILITY COMPANIES AND OTHER INTERESTED PARTIES THAT ALL
AVAILABLE INFORMATION HAS BEEN PROVIDED CONCERNING EXISTING UTILITY
LOCATION. VERIFY LOCATIONS GIVEN. CONTACT ARCHITECT IMMEDIATELY UPON
UNCOVERING UNKNOWN UTILITIES FOR FURTHER DIRECTION. INDICATE ALL
UNCOVERED UTILITIES ON RECORD DRAWINGS.
K.
INSTALL ROOF JACK AS REQUIRED AT ALL GAS PIPING ROOF PENETRATIONS.
L.
FIRE SEAL AROUND ALL PIPING AT PENETRATIONS THROUGH RATED WALLS, CEILINGS
AND TUNNELS PER UL LISTED MATERIAL FOR ACTUAL SEALANT BEING USED.
COORDINATE WITH ARCHITECTURAL PLANS FOR RATED WALL LOCATION.
M.
PROVIDE ALL APPROPRIATE TOOLS, WRENCHES, KEYS, ETC. AS REQUIRED FOR ACCESS
AND OPERATION OF VALVES, COVERS, ETC.
N.
DO NOT ROUTE PIPING UNDER EQUIPMENT LOCATED ABOVE CEILING. ROUTE PIPING
AROUND EQUIPMENT TO ALLOW FOR ACCESS AROUND EQUIPMENT AND FOR FUTURE
REMOVAL OF EQUIPMENT.
O.
P.
HOT (TEMPERED) AND COLD WATER REQUIRED UNLESS NOTED OTHERWISE ON PLUMBING FIXTURE
SCHEDULE. PROVIDE TEMPERATURE MIXING VALVE (ASSE 1070) AT THE FIXTURE.
THE CONTRACTOR IS TO VISIT THE SITE PRIOR TO BID TO FAMILIARIZE HIMSELF WITH
ALL CONDITIONS AS THEY EXIST. SUBMISSION OF BID INDICATES THE CONTRACTOR'S
UNDERSTANDING OF EXISTING CONDITIONS AND HIS WILLINGNESS TO WORK WITH
THESE CONDITIONS. NO ADDITIONAL TIME OR MONEY WILL BE ALLOTTED DUE TO LACK
OF COORDINATION WITH EXISTING CONDITIONS OR OTHER TRADES.
Q.
PLUMBING CONTRACTOR IS RESPONSIBLE FOR PROVIDING FLUES AND COMBUSTION
AIR PIPING TO EXTERIOR FOR GAS FIRED WATER HEATERS AND BOILERS.
PROVIDE HEAT TRAPS ON INCOMING AND DISCHARGE LINES FROM WATER HEATERS
WHICH DO NOT HAVE THEM FACTORY INSTALLED OR ARE NOT CONNECTED TO A
RECIRCULATING SYSTEM.
GAS PIPING:
1.
IF HORIZONTAL VENT LENGTH EXCEEDS 20 FEET, INCREASE VENT SIZE TO TWO INCHES.
COMMERCIAL KITCHEN SINKS GET HOT WATER, REMAINDER TO BE PROVIDED WITH TEMPERATURE
MIXING VALVE (ASSE 1070) AT THE FIXTURE.
SHOWER VALVES TO BE BALANCED-PRESSURE, THERMOSTATIC OR COMBINATION
BALANCED-PRESSURE/THERMOSTATIC CONFORMING TO ASSE 1016.
2.
3.
G:\2015\THRALL ISD - HIGH SCHOOL.084\84P1.01.dwg, 1/27/2016 3:29:37 PM, JESUS, DWG To PDF.pc3, ARCH full bleed E1 (30.00 x 42.00 Inches), 0.125:12
Q.
SUPPORT ALL GAS PIPING ON ROOF WITH PIPE STANDS/ROLLER EQUAL TO MIRO
INDUSTRIES MODEL 4-RAH-PC OR PORTABLE PIPE HANGERS, INC. (PPH), TYPE
PP10 WITH ROLLER. FOR PIPING 2-1/2", UP TO AND INCLUDING 8" USE MIRO
INDUSTRIES MODEL 6-RAH-PC OR PORTABLE PIPE HANGER, INC. (PPH) TYPE
PS-1-2. ALL PIPE STANDS TO SIT ON WALK BOARD (COORDINATE TYPE AND
METHODS OF SUPPORT WITH ROOFING CONTRACTOR). WALK BOARD TO BE A
MINIMUM OF 3" LARGER ON EACH SIDE THAN SUPPORT. PROVIDE MINIMUM PIPE
HEIGHT ABOVE ROOF DECK AS REQUIRED BY JURISDICTION HAVING AUTHORITY
(AT LEAST 6"). PROVIDE SUPPORTS FOR PIPING UNDER 2" AT SIX FEET ON
CENTER. PROVIDE SUPPORTS FOR PIPING 2" AND OVER AT EIGHT FEET ON
CENTER.
ROUTE PIPING DOWN MINIMUM TWELVE INCHES (12") UNDERGROUND AND STUB
UP FOR NEW GAS METER TO BE INSTALLED BY LOCAL GAS COMPANY. VERIFY GAS
SERVICE LOCATION WITH CIVIL DRAWINGS AND LOCAL GAS COMPANY BEFORE
INSTALLATION OF GAS PIPING. PAINT GAS RISER ON BUILDING TO MATCH
BUILDING EXTERIOR. PIPING UNDERGROUND TO BE WRAPPED FOR PROTECTION.
PROTECT ROOF DURING INSTALLATION. TEST PIPING USING COMPRESSED AIR AT
60 PSI. SOAP ALL JOINTS. RUN EQUIPMENT INLET LINE SIZE FROM REGULATOR TO
EQUIPMENT. PAINT ALL THE EXPOSED GAS PIPING.
INSTALL COMPRESSED AIR MAIN AS SHOWN ON PLANS. PIPING TO BE SCHEDULE 40
BLACK STEEL PIPE WITH CAPPED TEES AT EACH JOINT FOR FUTURE CONNECTION OF
COMPRESSED AIR LINES. CAPPED TEE TO FACE UP FOR CONNECTION OFF TOP OF
MAIN. MAKE DROPS SHOWN ON PLANS.
NOTES:
1.
2.
3.
4.
5.
6.
7.
8.
9.
REFERENCE SPECIFICATIONS FOR ADDITIONAL REQUIREMENTS.
ALL WALL HUNG FIXTURES TO BE INSTALLED WITH WALL CARRIERS, VERIFY
CONFIGURATION TYPE.
PROVIDE VANDAL RESISTANT SCREWS AT ALL FIXTURES.
INSTALL STAINLESS STEEL CAPS AT ALL UNUSED LAVATORY FAUCET HOLES.
NO OFFSET FLANGES WILL BE ALLOWED FOR WATER CLOSET INSTALLATIONS.
GROUT FOR LEVELING WATER CLOSETS SHALL NOT EXTEND UP ON SIDE OF WATER
CLOSET BASES. TAKE GROUT BACK TO MINIMUM 1/8" UNDER BASE AND CAULK FOR
FINAL FINISH. VERIFY CAULK COLOR AND TYPE WITH ARCHITECT.
REFERENCE ARCHITECTURAL CONTRACT DOCUMENTS FOR EXACT LOCATION AND
MOUNTING HEIGHTS OF ALL PLUMBING FIXTURES. CONTACT ARCHITECT FOR
ADDITIONAL INFORMATION AS REQUIRED.
PROVIDE INVERTED TEE CONNECTION FROM SINK TAILPIECE OR FLUSH VALVE TYPE
TRAP PRIMER CONNECTION TO ALL FLOOR DRAINS, FLOOR SINKS AND HUB DRAINS. AS
LAST RESORT PROVIDE MECHANICAL TYPE TRAP PRIMER (PPP INC. "OREGON #1" TYPE).
CONNECT TO NEAREST WATER SERVING THAT AREA PER MANUFACTURER'S
INSTALLATION INSTRUCTIONS.
ALL PLUMBING FIXTURES TO BE "LEAD FREE" AB1953 COMPLIANT (.25% OR LESS
AVERAGE LEAD CONTENT). PROVIDE DOCUMENTATION IN SUBMITTALS THAT THIS
REQUIREMENT IS MET FOR EACH APPLICABLE FIXTURE.
WC
WATER CLOSET: AMERICAN STANDARD FLOWISE MODEL 2234.001, FLOOR MOUNTED,
VITREOUS CHINA, 1 1/2" TOP SPUD, 15" HIGH ELONGATED BOWL.
EXPOSED FLUSH VALVE: SLOAN ROYAL #111 WITH EBV-550-A SFSM, SIDE MOUNT BATTERY
PACK AUTO FLUSH, 1.28 GALLON FLUSH.
SEAT: CHURCH MODEL 295CT, STA-TITE FASTENER, OPEN FRONT LESS COVER (WHITE).
WCAH
WATER CLOSET (ADULT ADA): AMERICAN STANDARD FLOWISE MODEL 3042.001, FLOOR
MOUNTED, VITREOUS CHINA, 1-1/2" TOP SPUD, 17-1/4" HIGH ELONGATED BOWL.
EXPOSED FLUSH VALVE: SLOAN ROYAL #111 WITH EBV-550-A SFSM, SIDE MOUNT BATTERY
PACK AUTO FLUSH, 1.28 GALLON FLUSH.
SEAT: CHURCH MODEL 295CT, STA-TITE FASTENER, OPEN FRONT LESS COVER (WHITE).
UR
URINAL: SLOAN #SU-1009-A, VITREOUS CHINA, WASH DOWN ACTION 3/4" TOP SPUD.
EXPOSED FLUSH VALVE: SLOAN ROYAL #186 WITH EBV-550-A SFSM, SIDE MOUNT BATTERY
PACK AUTO FLUSH, 0.125 GALLON FLUSH.
REFERENCE ARCHITECTURAL DRAWINGS FOR MOUNTING HEIGHT.
URH
URINAL: SLOAN #SU-1009-A, VITREOUS CHINA, WASH DOWN ACTION 3/4" TOP SPUD.
EXPOSED FLUSH VALVE: SLOAN ROYAL #186 WITH EBV-550-A SFSM, SIDE MOUNT BATTERY
PACK AUTO FLUSH, 0.125 GALLON FLUSH.
REFERENCE ARCHITECTURAL DRAWINGS FOR MOUNTING HEIGHT.
LH
LAVATORY (ADA): AMERICAN STANDARD 0356.015, 20" x 18" VITREOUS CHINA, WALL HUNG, 8"
FAUCET CENTERS AND GRID STRAINER. PROVIDE WITH TEMPERATURE MIXING VALVE EQUAL
TO POWERS HYDROGUARD T/P e480 SERIES, .5 GPM MINIMUM FLOW, ASSE 1070, INTEGRAL
CHECKS, 1.9 GPM AT 10 psi DROP.
FAUCET: CHICAGO #404-HZ317CP, TEMPERED AND COLD WATER, 4" WRIST BLADE HANDLES,
E-12 AERATOR.
WF3
WASH FOUNTAIN (ADA): BRADLEY MODEL NO. SS - 3N/AST4-TMA, CONTINUOUS POLYESTER
RESIN BOWL FOR 3 USERS, 3 SPAY HEADS WITH INDEPENDENT PUSHBUTTON AIR METERING
ACTIVATION. ACRYLIC LAMINATE PEDESTAL, WALL HUNG FRAME, THERMOSTATIC MIXING
VALVE (ASSE 1070).
SKH
SINK (ADA): ELKAY #LRAD-2219-55 (OFF-CENTER DRAIN), 18 GAUGE STAINLESS STEEL,
SELF-RIM, 18" x 14" x 5.5" DEEP BOWL, THREE (3) FAUCET HOLES WITH STAINLESS STEEL
BASKET STRAINER. PROVIDE WITH TEMPERATURE MIXING VALVE EQUAL TO POWERS
HYDROGUARD T/P e480 SERIES, .5 GPM MINIMUM FLOW, ASSE 1070, INTEGRAL CHECKS, 1.9
GPM AT 10 psi DROP.
FAUCET: ELKAY #LK-2423BH, SWING GOOSENECK, WRIST BLADE HANDLES.
SKART
ART ROOM DEEP SINK: JUST #SLXD-1921-A-GR, 18 GAUGE STAINLESS STEEL, SELF-RIM, 18" x
14" x 12" DEEP BOWL, THREE (3) FAUCET HOLES WITH STAINLESS STEEL BASKET STRAINER.
FAUCET: ELKAY #LK2432BH, SWING GOOSENECK, WRIST BLADE HANDLES.
PROVIDE WITH TEMPERATURE MIXING VALVE EQUAL TO POWERS HYDROGUARD T/P e480
SERIES, .5 GPM MINIMUM FLOW, ASSE 1070, INTEGRAL CHECKS, 1.9 GPM AT 10 psi DROP.
SKART1
ART ROOM ADA SINK: JUST #SL-ADA-1921-A-GR, 18 GAUGE STAINLESS STEEL, SELF-RIM, 18" x
14" x 5.5" DEEP BOWL, THREE (3) FAUCET HOLES WITH STAINLESS STEEL BASKET STRAINER.
FAUCET: ELKAY #LK2432BH, SWING GOOSENECK, WRIST BLADE HANDLES.
PROVIDE WITH TEMPERATURE MIXING VALVE EQUAL TO POWERS HYDROGUARD T/P e480
SERIES, .5 GPM MINIMUM FLOW, ASSE 1070, INTEGRAL CHECKS, 1.9 GPM AT 10 psi DROP.
KSH
KITCHEN SINK (ADA): ELKAY #LRAD-3319 (OFF-CENTER DRAIN), 18 GAUGE STAINLESS STEEL,
SELF-RIM, TWO (2) 14" x 14" x 5.5" DEEP BOWLS, FOUR (4) FAUCET HOLES WITH TWO (2)
STAINLESS STEEL BASKET STRAINERS.
FAUCET: ELKAY #LKD2443, SWING GOOSENECK, METAL WING HANDLES, HOSE SPRAYER.
PROVIDE WITH TEMPERATURE MIXING VALVE EQUAL TO POWERS HYDROGUARD T/P e480
SERIES, .5 GPM MINIMUM FLOW, ASSE 1070, INTEGRAL CHECKS, 1.9 GPM AT 10 psi DROP.
SS2
LAUNDRY ROOM FREE STANDING DEEP SINK: ELKAY #WNSF81362, 14 GAUGE STAINLESS
STEEL, 1/4" RADIUS COVED CORNER CONSTRUCTION, 36" x 24" x 14" DEEP BOWL, 8" HIGH FULL
LENGTH BACKSPLASH , STAINLESS STEEL TUBULAR LEGS WITH ADJUSTABLE BULLET SHAPED
FEET.
FAUCET: ELKAY #LK907BR07L2H, LEVER HANDLES, BUCKET HOOK, VACUUM BREAKER.
US4
UTILITY SINK: 96" GRIFFIN PRODUCTS, INC. MODEL MS-496, 16 GA., TYPE 304 STAINLESS STEEL
SINK AND TUBULAR BRACES, 9" BACK SPLASH, FLAT STRAINER DRAIN.
FAUCETS: FOUR (4) MODEL FG-105, GOOSENECK FAUCETS WITH 4" WRIST BLADE HANDLES.
PROVIDE WITH TEMPERATURE MIXING VALVE EQUAL TO POWERS HYDROGUARD T/P E480
SERIES, .5 GPM MINIMUM FLOW, ASSE 1070, INTEGRAL CHECKS, 1.9 GPM AT 10 PSI DROP.
EWCH
ELECTRIC WATER COOLER (ADA): ELKAY #LVRCGRNTL8SC, HIGH EFFICIENCY, FILTERED,
VANDAL RESISTANT, TWO (2) STATION, VANDAL RESISTANT PUSH BUTTON IN FRONT, VANDAL
RESISTANT BUBBLERS, STAINLESS STEEL FINISH, CANE APRON. 120V-1PH.
SHH
SHOWER (ADA): PROVIDE WHITE FREEDOM MODEL APFQ3698BF625 ADA FIBERGLASS SHOWER
STALL WITH COLLAPSIBLE WATER RETAINER, FOLDING SHOWER SEAT, CAULKLESS DRAIN,
GRAB BARS, SHOWER CURTAIN AND ROD, MOEN PRESSURE BALANCE SHOWER VALVE AND
HAND HELD SHOWER WITH 69" CHROME METAL COVERED HOSE AND SLIDE BAR. LEFT OR
RIGHT HANDED AS REQUIRED.
SH
SHOWER: PROVIDE WHITE AQUARIUS MODEL G3679SH FIBERGLASS SHOWER STALL WITH
COLLAPSIBLE WATER RETAINER, CAULKLESS DRAIN, SHOWER CURTAIN AND ROD, MOEN
MODEL 8375EP15 PRESSURE BALANCE SHOWER VALVE AND 1.5 GPM WALL MOUNT SHOWER
HEAD. LEFT OR RIGHT HANDED AS REQUIRED.
HB
HOSE BIBB: WOODFORD MODEL B67 SERIES, IN FLUSH MOUNTING WALL BOX, ASSE 1052 OR
1101 BACKFLOW PROTECTED AUTOMATIC DRAINING, FREEZELESS, NO SPRAYBACK. PROVIDE
SHUT-OFF VALVE INSIDE BUILDING IN ACCESSIBLE LOCATION. SLOPE LINE FROM SHUT-OFF
VALVE TO WALL HYDRANT TO ALLOW DRAINING OF LINE FOR FREEZE PROTECTION.
HB2
HOSE BIBB: WOODFORD MODEL 26, TEE KEY OPERATOR, ASSE 1052 OR 1101 BACKFLOW
PREVENTER, CLOSE COUPLED, NO SPRAYBACK. PROVIDE SHUT-OFF VALVE INSIDE BUILDING
IN ACCESSIBLE LOCATION. SLOPE LINE FROM SHUT-OFF VALVE TO WALL HYDRANT TO ALLOW
DRAINING OF LINE FOR FREEZE PROTECTION.
HWRP1B, 2B, 1C, 1E
HOT WATER RECIRCULATION PUMP: GRUNDFOS UPS15-55, 4 GPM AT TEN FEET (10') OF HEAD.
1/12 HP-120V-1PH.
WH 1A
WATER HEATER: A.O.SMITH MODEL DEL-20, 20 GALLON STORAGE, 3KW-208V-1PH
NON-SIMULTANEOUS ELEMENTS, 15 GPH RECOVERY AT 80 DEGREES RISE.
WH 1B, 2B, 3B
WATER HEATER: A.O.SMITH MODEL MXiBTH199, 95%, 100 GALLON STORAGE, 199 MBH INPUT,
ASSEMBLY.
WH 1C
WATER HEATER: A.O.SMITH MODEL DEL-30, 30 GALLON STORAGE, 6KW-208V-1PH
NON-SIMULTANEOUS ELEMENTS, 30 GPH RECOVERY AT 80 DEGREES RISE.
WH 1E
WATER HEATER: A.O.SMITH MODEL DEN-40, 40 GALLON STORAGE, 3KW-208V-1PH
NON-SIMULTANEOUS ELEMENTS, 15 GPH RECOVERY AT 80 DEGREES RISE
ANT
ACID NEUTRALIZATION TANK: ORION STYLE 8, POLYETHYLENE, POINT OF USE, 1.5 GALLONS,
TOP INLET/OUTLET/CLEANOUT. FILL WITH LIMESTONE CHIPS FOR ACID NEUTRALIZATION.
SI
SOLIDS INTERCEPTOR: JAY R. SMITH #8710 WHITE DUCO COATED STEEL BODY AND
REMOVABLE STAINLESS STEEL SCREEN AND CAST IRON COVER, 2" PIPE SIZE. RE:
ARCHITECTURAL FOR LOCATION. ROUGH-IN SO IT WILL SET ON THE VERY BOTTOM SHELF.
WB
WALL BOX FOR CONNECTION TO REFRIGERATOR WATER AND/OR ICE MAKER EQUAL TO SOUIX
CHIEF 696 SERIES WITH ABS OUTLET BOX, 1/4 TURN VALVE AND ASSE 1010 WATER HAMMER
ARRESTOR.
WM
WASHING MACHINE SUPPLY AND DRAIN: GUY GRAY 20 GAUGE POWDER COATED BOX AND
FACEPLATE, 2" DRAIN PIPE, TOP OR BOTTOM SUPPLY, 1/4 TURN BALL VALVES AND WATER
HAMMER ARRESTERS.
FD
FLOOR DRAIN (GENERAL PURPOSE): C.I. BODY, FLASHING COLLAR, WEEPHOLES, ADJUSTABLE
STAINLESS STEEL OR NICKEL BRONZE ROUND TOP (6" DIAMETER). MIFAB F1100 CS-3 SERIES.
FD4
FLOOR DRAIN (SINGLE STALL SHOWER): C.I. BODY, ADJUSTABLE CLAMPING COLLAR,
WEEPHOLES, ADJUSTABLE STAINLESS STEEL OR NICKEL BRONZE STRAINER (6" DIAMETER),
AND STAINLESS STEEL SEDIMENT BASKET. MIFAB F1100 C 5-3 SERIES.
THERMOSTATIC MIXING VALVE (ASSE 1070).
FD7
FLOOR DRAIN (KITCHEN): C.I. BODY, FLASHING COLLAR, WEEPHOLES, SECURED AND
ADJUSTABLE STAINLESS STEEL OR NICKEL BRONZE SQUARE TOP (6" x 6") MINIMUM WITH
COPPER SEDIMENT BASKET. TOP SIZE TO MATCH TILE SIZE AS CLOSE AS POSSIBLE, VERIFY
TOP SIZE. MIFAB F1100 CS-3-5 SERIES.
SS
SERVICE SINK: FIAT #MSB-2424, ONE-PIECE MOLDED STONE WITH #832-AA HOSE AND HOSE
BRACKET #E-77-AA VINYL BUMPER GUARD, MSG-2424 STAINLESS STEEL WALL GUARD AND
#830-AA FAUCET.
FD8
KETTLE DRAIN: C.I. BODY, WEEPHOLES, FLASHING COLLAR, ADJUSTABLE SATIN NICKEL
BRONZE STRAINER (7" DIAMETER) 4" DIAMETER FUNNEL EXTENSION. MIFAB F1100 C N7-F4
SERIES.
SS1
TUBA SINK: GRIFFIN JUMBO SINK MODELJS-423, 36"T x 42"W x 33.5"D, 16 GA., TYPE 304
FS
FLOOR SINK: 6" DEEP WITH ACID-RESISTING PORCELAIN ENAMEL INTERIOR, ALUMINUM
INTERNAL DOME STRAINER, and STAINLESS STEEL GRATE (1/2 GRATE TYPE). MIFAB FS1720-3
SERIES.
HS
KITCHEN HAND SINK (ADA): ELKAY #ELVW02219, 304 STAINLESS STEEL, NSF, COMPLETE WITH
WALL HANGER, INTEGRAL STAINLESS STEEL SUPPORT BRACKETS, INTEGRAL OVERFLOW.
BACKSPLASH.
VALVE EQUAL TO POWERS HYDROGUARD T/P E480 SERIES, .5 GPM MINIMUM FLOW, ASSE 1070,
INTEGRAL CHECKS, 1.9 GPM AT 10 PSI DROP.
YH
YARD HYDRANT: WOODFORD MODEL Y2, AUTOMATIC DRAINING, FREEZELESS, NO
SPRAYBACK,ASSE 1052 OR 1101 BACKFLOW PREVENTER. PROVIDE DRYWELL ADJACENT TO
HYDRANT. INSTALL PER MANUFACTURERS INSTALLATION DETAILS/REQUIREMENTS.
DBP
DOMESTIC BOOSTER PUMP SYSTEM: "LITTLE GIANT INLINE CP WATER BOOSTER SYSTEM" TO
INCLUDE FOUR (4) PUMPS (208V-1PH), TWO (2) SUB DRIVE DUPLEX ALTERNATORS, FOUR (4) 2.5
GALLON EXPANSION TANKS, PRESSURE SENSOR FITTINGS, ADJUSTABLE PRESSURE VALVE
(NORMALLY SET AT MAINTAINING 55 PSI FROM THE FACTORY).
AR
AIR REEL: COXREELS "P" SERIES MODEL P-LP-130, SPRING RETURN, 300 psi MAX PRESSURE,
30 FOOT, 1/2" O.D. HOSE, 1" SOLID STEEL AXLE AND LUBRICATED BEARINGS, ONE PIECE HEAVY
GAUGE 1/4" STEEL BASE AND SUPPORT POST, NITRILE SEIVEL SEALS, ADJUSTABLE GUIDE
ARM, HEAVY DUTY STEEL CONSTRUCTION. INSTALL PER MANUFACTURERS INSTALLATION
REQUIREMENTS.
WATER PIPING:
WATER PIPING TO BE COPPER PER SPECIFICATIONS WITH THE
FOLLOWING EXCEPTION. PROVIDE PEX-a PIPING FOR
DOMESTIC HOT AND COLD WATER PIPING THAT IS 2" AND
SMALLER ONLY. DOMESTIC WATER PIPING TO BE INSULATED
PER SPECIFICATIONS. PEX-a DOMESTIC COLD WATER PIPING
CAN BE UNINSULATED. ALL DOMESTIC HOT WATER PIPNG (
COPPER AND PEX-a) IS TO BE INSULATED PER SPECIFICATIONS.
ALL PEX-a PIPING MUST BE PROVIDED WITH PEX-a PIPE
SUPPORT INSTALLED PER PIPING MANUFACTURER'S
INSTALLATION INSTRUCTIONS TO MEET 25/50 SMOKE RATING
AND TO ALLOW FOR HANGERS/SUPPORTS TO BE SPACED THE
SAME AS COPPER PIPING.
SCHEDULES, NOTES, & LEGENDS - PLUMBING
P1.01
1 OF 8
G:\2015\THRALL ISD - HIGH SCHOOL.084\84P1.02.dwg, 1/27/2016 3:29:44 PM, JESUS, DWG To PDF.pc3, ARCH full bleed E1 (30.00 x 42.00 Inches), 0.125:12
ALL VALVE LOCATIONS AND
NUMBERS TO BE RECORDED
ON RECORD DRAWINGS.
DETAILS - PLUMBING
P1.02
2 OF 8
1
DO NOT ROUTE ANY PIPING ABOVE THIS AREA.
2
CONNECT TO WASTEWATER (WW) STUB PROVIDED BY CIVIL. FIELD VERIFY
EXACT LOCATION AND INVERT. PROVIDE ADAPTER AS REQUIRED TO MAKE
SIZE AND/OR MATERIAL TRANSITION.
3
RE: DOUBLE CLEANOUT DETAIL ON PLUMBING DETAIL SHEET(S).
4
RE: EXTERIOR CLEANOUT DETAIL ON PLUMBING DETAIL SHEET(S).
5
RE: INTERIOR CLEANOUT DETAIL ON PLUMBING DETAIL SHEET(S).
6
RE: TYPICAL CONDENSATE STUB DETAIL ON PLUMBING DETAIL SHEET(S).
401
VEST
452
FEC
VEST
455
STAGE CONTROL & STORAGE
212
456
LRC OFFICE
208
GYMNASIUM
400
COMMONS
209
STAGE
457
LEARNING RESOURCE CENTER
207
REFER TO X1.01 FOR
STAGE THEATRICAL
EQUIPMENT LAYOUT
CONCESSION
458
CM OFFICE
204
ENGLISH CLASSROOM
201
VEST
459
ENGLISH CLASSROOM
LEARNING RESOURCE ANNEX
202
CONTENT MASTERY
206
FEC
203
CUST
TABLE STORAGE
461
460
IDF
205
W/D
VEST
SHOWERS
420
434
ELECTRICAL
PANEL
432
STORAGE
LAUNDRY & CUST
FEC
433
RR
421
RR
SHOWERS
423
431
CORRIDOR
424
200
BOOK ROOM
COACH'S LOCKER
RR
428
GIRLS JV LOCKERS
WALL OF HONOR
G:\2015\THRALL ISD - HIGH SCHOOL.084\84P2.01.dwg, 1/27/2016 3:29:52 PM, JESUS, DWG To PDF.pc3, ARCH full bleed E1 (30.00 x 42.00 Inches), 0.125:12
VEST
STORAGE
463
462
427
GIRLS VARSITY LOCKERS
422
RR
RR
115
114
430
CORRIDOR
119
CLASSROOM
118
VEST
425
COACH'S OFFICE
426
VEST
TEACHER'S WORKROOM & BREAK ROOM
429
CLASSROOM
CLASSROOM
116
117
113
CORRIDOR
SUPPLY
100
112
FEC
FEC
TEST STORAGE
SECURE VESTIBULE
CLASSROOM
101
CLASSROOM
CLASSROOM
102
103
CLASSROOM
RECEPTION
106
CONFERENCE
111
110
105
104
HALL
107
PRINCIPAL
109
COUNSELOR
108
FLOOR PLAN - AREA A - PLUMBING - WASTEWATER
P2.01
3 OF 8
1.
2.
3.
4.
HOT (TEMPERED) AND COLD WATER REQUIRED UNLESS NOTED OTHERWISE ON PLUMBING FIXTURE
SCHEDULE. PROVIDE TEMPERATURE MIXING VALVE (ASSE 1070) AT THE FIXTURE.
IF HORIZONTAL VENT LENGTH EXCEEDS 20 FEET, INCREASE VENT SIZE TO TWO INCHES.
COMMERCIAL KITCHEN SINKS GET HOT WATER, REMAINDER TO BE PROVIDED WITH TEMPERATURE
MIXING VALVE (ASSE 1070) AT THE FIXTURE.
SHOWER VALVES TO BE BALANCED-PRESSURE, THERMOSTATIC OR COMBINATION
BALANCED-PRESSURE/THERMOSTATIC CONFORMING TO ASSE 1016.
5.
ALL FLOOR DRAINS AND FLOOR SINKS MUST HAVE TRAP PRIMERS. PROVIDE INVERTED TEE
CONNECTION FROM SINK TAILPIECE OR FLUSH VALVE TYPE TRAP PRIMER CONNECTION TO
ALL FLOOR DRAINS, FLOOR SINKS AND HUB DRAINS. AS LAST RESORT PROVIDE
MECHANICAL TYPE TRAP PRIMER (PPP INC. "OREGON #1" TYPE). CONNECT TO NEAREST
WATER SERVING THAT AREA PER MANUFACTURER'S INSTALLATION INSTRUCTIONS. IN
JURISDICTIONS WHERE PRESSURE ACTIVATED MECHANICAL PRIMERS ARE NOT ALLOWED,
USE ELECTRONIC TRAP PRIMERS. COORDINATE POWER REQUIREMENTS WITH ELECTRICAL
CONTRACTOR. PROSET "TRAP GUARD" DEVICE MAY BE USED IN LIEU OF TRAP PRIMERS
WHEN ALLOWED BY LOCAL CODE AUTHORITY HAVING JURISDICTION. BEFORE USING
PROSET "TRAP GUARD" CONTRACTOR MUST OBTAIN WRITTEN APPROVAL FROM LOCAL
CODE AUTHORITY HAVING JURISDICTION AND PROVIDE COPIES TO ARCHITECT AND
ENGINEER.
MANUFACTURERS:
ISIMET UTILITY CONTROLLER AND E-SERIES ENCLOSURE - (210) 654-8015 or
LAB SAFETY SYSTEMS UTILITY CONTROLLERS - (512-845-3528)
1
DO NOT ROUTE ANY PIPING ABOVE THIS AREA.
1.
2
CONNECT TO WASTEWATER (WW) STUB PROVIDED BY CIVIL. FIELD VERIFY EXACT
LOCATION AND INVERT. PROVIDE ADAPTER AS REQUIRED TO MAKE SIZE AND/OR
MATERIAL TRANSITION.
3
RE: DOUBLE CLEANOUT DETAIL ON PLUMBING DETAIL SHEET(S).
4
RE: EXTERIOR CLEANOUT DETAIL ON PLUMBING DETAIL SHEET(S).
5
RE: INTERIOR CLEANOUT DETAIL ON PLUMBING DETAIL SHEET(S).
6
RE: TYPICAL CONDENSATE STUB DETAIL ON PLUMBING DETAIL SHEET(S).
7
TWO WAY SINGLE RISER CLEANOUT TO ACT AS SAMPLING PORT.
8
CONNECT TO STORM SEWER STUB PROVIDED BY CIVIL. FIELD VERIFY EXACT
LOCATION AND INVERT. PROVIDE ADAPTER AS REQUIRED TO MAKE SIZE AND/OR
MATERIAL TRANSITION.
PIPING SIZE FOR WATER MAIN DROPS AND MANIFOLD IN CHASE OR WALL TO REMAIN FULL
SIZE OF DROP INDICATED. REFERENCE FIXTURE CONNECTION SCHEDULE FOR INDIVIDUAL
LINE SIZE TO EACH FIXTURE.
COORDINATE ALL WASTEWATER FLOOR PENETRATIONS AND PIPING PENETRATIONS WITH
STRUCTURAL PRIOR TO INSTALLATION. PIPING MAY BE OFFSET SLIGHTLY TO AVOID
STRUCTURAL CONFLICTS.
ROUTE VENT FROM EACH FIXTURE TO HORIZONTAL VENT HEADER IN CHASE/WALL OR TO
NEAREST COMMON VTR ABOVE CEILING. REFERENCE FIXTURE CONNECTION SCHEDULE
FOR INDIVIDUAL FIXTURE VENT SIZES. VENT HEADERS IN CHASE TO BE SIZED
ACCORDINGLY: 1 1/2" VENT UP TO 6 DRAIN FIXTURE UNITS MAXIMUM DEVELOPED LENGTH
OF 60 FEET (EXCEPT FOR WATER CLOSETS), 2" VENT UP TO 20 DRAIN FIXTURE UNITS
MAXIMUM DEVELOPED LENGTH OF 120 FEET, 3" VENT UP TO 84 DRAIN FIXTURE UNITS
MAXIMUM DEVELOPED LENGTH OF 212 FEET AND 4" VENT UP TO 256 DRAIN FIXTURE UNITS
MAXIMUM DEVELOPED LENGTH OF 300 FEET. BRANCH VENTS EXCEEDING 40 FEET IN
DEVELOPED LENGTH ARE TO BE INCREASED BY ONE PIPE SIZE. NO MORE THAN 1/3 OF THE
CODE PERMITTED DEVELOPED LENGTH SHALL BE IN HORIZONTAL POSITION. EXTEND
COMMON VENT UP THROUGH ROOF.
ROUTE ALL VENTS TO NEAREST COMMON VENT THRU ROOF (VTR) TO MINIMIZE ROOF
PENETRATIONS. VTR TO BE MINIMUM 15 FEET AWAY FROM OUTSIDE AIR INTAKES.
COORDINATE WITH MECHANICAL CONTRACTOR PRIOR TO INSTALLATION.
2.
ELECTRICAL CONTRACTOR: PROVIDE A UTILITY CONTROLLER (1000 SERIES 12X9) AND
E-SERIES (E3112-EX) CONTACTOR ENCLOSURE FOR EMERGENCY SHUT-OFF OF POWER
(RECEPTACLES), COLD WATER, TEMPERED WATER AND GAS AS REQUIRED (VERIFY EXACT
UTILITIES REQUIRED IN EACH INDIVIDUAL ROOM WITH PLUMBING CONTRACTOR). PROVIDE
INDIVIDUAL CONTROL SWITCH FOR CW/HW/GAS/RECEPTACLES. EXHAUST FANS FOR HOODS
TO BE CONTROLLED FROM UTILITY CONTROLLER WITH KEY SWITCH TO ENABLE FAN SWITCH
ON HOOD. CONTACTOR ENCLOSURES TO BE MOUNTED ABOVE CEILING. ELECTRICAL
CONTRACTOR TO FURNISH AND INSTALL UTILITY CONTROLLER AND E-SERIES CONTACTOR
ENCLOSURE AND PROVIDE ALL 120 VOLT WIRING AND 24V WIRING BETWEEN CONTROLLER,
CONTACTOR ENCLOSURE AND EQUIPMENT. PROVIDE CONTACTOR ENCLOSURES FOR (12)
TWELVE CIRCUITS. ELECTRICAL CONTRACTOR TO ALSO PROVIDE 24 VOLT CONTROL WIRING
BETWEEN UTILITY CONTROLLER AND S-SERIES SOLENOID ENCLOSURE. INNER CONNECT
WITH FACP TO SHUT DOWN SERVICES. COORDINATE WITH FIRE ALARM CONTRACTOR.
PLUMBING CONTRACTOR: PROVIDE PRE-ASSEMBLED S-SERIES (S-3113-24VAC-X-K-F-R-A-U)
SOLENOID ENCLOSURE WITH ALL CONTACTS RESET SOLENOID AND INTERFACE RELAYS FOR
EACH SCIENCE ROOM FOR EMERGENCY SHUT-OFF OF COLD WATER, TEMPERED WATER AND
GAS. EACH SOLENOID TO BE ASSEMBLED WITH THREADED BALL VALVE, UNIONS, "Y"
STRAINERS, SHOCK ARRESTOR, AND CAPPED ENDS FOR FIELD INSTALLATION. ENCLOSURE
SHALL BE NEMA 1, SURFACE MOUNT ABOVE CEILING. FIELD VERIFY EXACT MOUNTING
ARRANGEMENT. VERIFY EXACT UTILITIES REQUIRED IN EACH INDIVIDUAL ROOM .
9
ISLAND SINK. RE: ISLAND SINK DETAIL ON DETAIL SHEET(S).
10
SOLIDS INTERCEPTOR EQUAL TO PARK MODEL STSC-150, 150 CALLUN CAPACITY, 15
GPM (REQUIRED BECAUSE DISPOSERS ARE UTILIZED).
3.
ELECTRICAL AND PLUMBING CONTRACTOR TO COORDINATE ALL REQUIREMENTS TO
PROVIDE A COMPLETE AND WORKABLE SYSTEM.
11
4.
PROVIDE FACTORY START-UP WITH PLUMBING AND ELECTRICAL CONTRACTOR PRESENT
AND SIGNED START-UP CERTIFICATE.
SOLIDS INTERCEPTOR TO BE SET IN ADJACENT CABINET SPACE TO ALLOW FOR
CLEAR ADA SPACE BENEATH SINK. INSTALL SO THAT TOP CAN BE REMOVED AND
INTERCEPTOR CAN BE CLEANED PER MANUFACTURERS INSTRUCTIONS
5.
WHEN EMERGENCY BUTTON IS DEPRESSED, POWER IS SHUT OFF TO ALL ANCILLARY
DEVICES.
6.
ROOM EXHAUST CONTROLLED SEPARATELY BY TIMER SWITCH ON WALL PROVIDED BY
ELECTRICAL CONTRACTOR.
7.
COORDINATE WITH BUILDING B.M.S. SYSTEM AS REQUIRED FOR DAILY SHUT-DOWN SIGNAL.
ALL SCIENCE ROOM AND SCIENCE PREP ROOM
EMERGENCY SHOWERS, SINKS AND FAUCETS ARE TO
BE PROVIDED BY SCIENCE CASEWORK CONTRACTOR.
PLUMBING CONTRACTOR TO PROVIDE ROUGH-IN AND
CONNECTION TO SUPPLIES AND WASTE. FAUCETS TO
HAVE INTEGRAL VACUUM BREAKER OR OTHER MEANS
OF BACKFLOW PROTECTION.
FEC
W/D
FEC
FEC
FEC
FEC
F
ICE
FEC
FEC
FEC
FEC
DW
G:\2015\THRALL ISD - HIGH SCHOOL.084\84P2.02.dwg, 1/27/2016 3:30:03 PM, JESUS, DWG To PDF.pc3, ARCH full bleed E1 (30.00 x 42.00 Inches), 0.125:12
DW
FEC
FLOOR PLAN - AREA B - PLUMBING - WASTEWATER
P2.02
4 OF 8
B.1
B.2
B.3
1
DO NOT ROUTE ANY PIPING ABOVE THIS AREA.
2
CONNECT TO WASTEWATER (WW) STUB PROVIDED BY CIVIL. FIELD VERIFY EXACT
LOCATION AND INVERT. PROVIDE ADAPTER AS REQUIRED TO MAKE SIZE AND/OR
MATERIAL TRANSITION.
3
CONNECT TO COLD WATER (CW) STUB PROVIDED BY CIVIL. FIELD VERIFY EXACT
LOCATION. PROVIDE ADAPTER AS REQUIRED TO MAKE SIZE AND/OR MATERIAL
TRANSITION.
4
RE: CW BUILDING ENTRY DETAIL ON PLUMBING DETAIL SHEET(S).
5
RE: DOUBLE CLEANOUT DETAIL ON PLUMBING DETAIL SHEET(S).
6
RE: EXTERIOR CLEANOUT DETAIL ON PLUMBING DETAIL SHEET(S).
7
RE: INTERIOR CLEANOUT DETAIL ON PLUMBING DETAIL SHEET(S).
8
WATER HEATER ON MEZZANINE. RE: WATER HEATER DETAIL ON PLUMBING DETAIL
SHEET(S) FOR WATER HEATER PIPING.
9
RE: TYPICAL CONDENSATE STUB DETAIL ON PLUMBING DETAIL SHEET(S).
10
CONNECT TO GAS STUB PROVIDED BY CIVIL. FIELD VERIFY EXACT LOCATION AND
INVERT. PROVIDE ADAPTER AS REQUIRED TO MAKE SIZE AND/OR MATERIAL
TRANSITION. PROVIDE SHUTOFF VALVE, PRESSURE REGULATOR AND TEST
CONNECTION IN RISER. REFERENCE GAS RISER DETAIL ON DETAIL SHEETS. PAINT
RISER TO MATCH BUILDING.
11
LOW PRESSURE GAS ABOVE CEILING OR EXPOSED IN SHOP.
12
SOLENOID VALVE TO BE OPERATED BY EMERGENCY SHUT-OFF BUTTON IN ROOM.
VERIFY EXACT LOCATION OF BUTTON WITH OWNER PRIOR TO ROUGH-IN.
13
COMPRESSED AIR MAIN TO CONNECT TO OWNER PROVIDED AIR COMPRESSOR.
14
3/4" COMPRESSED AIR DOWN ON WALL TO WALL MOUNTED AIR REEL. COORDINATE
EXACT HEIGHT AND LOCATION WITH OWNER PRIOR TO ROUGH-IN.
15
3/4" COMPRESSED AIR TO CONNECT TO AIR REEL MOUNTED TO STRUCTURE.
COORDINATE EXACT HEIGHT AND LOCATION WITH OWNER PRIOR TO ROUGH-IN.
16
LOW PRESSURE GAS DOWN TO SERVE
B.5
B.4
B.A
B.A
AR WALL
B.B
B.B
B.C
B.C
GAS DEMAND
DEMAND = 780 MBH
LENGTH = 200 FEET
FEC
B.D
F
F
F
B.D
B.E
B.E
FEC
B.F
G:\2015\THRALL ISD - HIGH SCHOOL.084\84P2.03.dwg, 1/27/2016 3:30:13 PM, JESUS, DWG To PDF.pc3, ARCH full bleed E1 (30.00 x 42.00 Inches), 0.125:12
W/D
B.F
FEC
RG
RG
RG
RG
B.G
B.G
B.H
B.H
B.1
B.2
B.3
B.4
B.5
FLOOR PLAN - AREA C - PLUMBING
P2.03
5 OF 8
WATER PIPING:
WATER PIPING TO BE COPPER PER SPECIFICATIONS WITH THE
FOLLOWING EXCEPTION. PROVIDE PEX-a PIPING FOR
DOMESTIC HOT AND COLD WATER PIPING THAT IS 2" AND
SMALLER ONLY. DOMESTIC WATER PIPING TO BE INSULATED
PER SPECIFICATIONS. PEX-a DOMESTIC COLD WATER PIPING
CAN BE UNINSULATED. ALL DOMESTIC HOT WATER PIPNG (
COPPER AND PEX-a) IS TO BE INSULATED PER SPECIFICATIONS.
ALL PEX-a PIPING MUST BE PROVIDED WITH PEX-a PIPE
SUPPORT INSTALLED PER PIPING MANUFACTURER'S
INSTALLATION INSTRUCTIONS TO MEET 25/50 SMOKE RATING
AND TO ALLOW FOR HANGERS/SUPPORTS TO BE SPACED THE
SAME AS COPPER PIPING.
1
DO NOT ROUTE ANY PIPING ABOVE THIS AREA.
2
ROUTE GAS TIGHT TO WALL IN GYM.
3
ROUTE LOW PRESSURE GAS LOW ON WALL.
4
RE: WATER HEATER DETAIL ON PLUMBING DETAIL SHEET(S) FOR WATER HEATER
AND HOT WATER RECIRCULATION PUMP PIPING.
5
INSURE ADEQUATE SPACE (48" MIN.) IS LEFT FOR LADDER ACCESS TO MEZZANINE.
6
CONNECT TO GAS STUB PROVIDED BY CIVIL. FIELD VERIFY EXACT LOCATION.
7
PROVIDE SHUT-OFF VALVE, GAS REGULATOR AND TEST CONNECTION IN GAS RISER
PER GAS RISER DETAIL ON DETAIL SHEET(S).
401
VEST
452
FEC
VEST
455
STAGE CONTROL & STORAGE
212
456
LRC OFFICE
208
GYMNASIUM
400
COMMONS
209
STAGE
457
LEARNING RESOURCE CENTER
207
REFER TO X1.01 FOR
STAGE THEATRICAL
EQUIPMENT LAYOUT
CONCESSION
458
CM OFFICE
204
ENGLISH CLASSROOM
201
VEST
459
ENGLISH CLASSROOM
LEARNING RESOURCE ANNEX
202
CONTENT MASTERY
206
FEC
203
CUST
TABLE STORAGE
461
460
IDF
205
W/D
VEST
SHOWERS
420
434
ELECTRICAL
PANEL
432
STORAGE
LAUNDRY & CUST
FEC
433
RR
421
RR
SHOWERS
423
431
CORRIDOR
424
200
BOOK ROOM
COACH'S LOCKER
RR
428
GIRLS JV LOCKERS
WALL OF HONOR
G:\2015\THRALL ISD - HIGH SCHOOL.084\84P3.01.dwg, 1/27/2016 3:30:27 PM, JESUS, DWG To PDF.pc3, ARCH full bleed E1 (30.00 x 42.00 Inches), 0.125:12
VEST
STORAGE
463
462
427
GIRLS VARSITY LOCKERS
422
RR
RR
115
114
430
CORRIDOR
119
CLASSROOM
118
VEST
425
COACH'S OFFICE
426
VEST
TEACHER'S WORKROOM & BREAK ROOM
429
CLASSROOM
CLASSROOM
116
117
113
CORRIDOR
SUPPLY
100
112
FEC
FEC
TEST STORAGE
SECURE VESTIBULE
CLASSROOM
101
CLASSROOM
CLASSROOM
102
103
CLASSROOM
RECEPTION
106
CONFERENCE
111
110
105
104
HALL
107
PRINCIPAL
109
COUNSELOR
108
FLOOR PLAN - AREA A - PLUMBING - SUPPLY
P3.01
7 OF 8
1.
ALL FLOOR DRAINS AND FLOOR SINKS MUST HAVE TRAP PRIMERS. PROVIDE INVERTED TEE
CONNECTION FROM SINK TAILPIECE OR FLUSH VALVE TYPE TRAP PRIMER CONNECTION TO
ALL FLOOR DRAINS, FLOOR SINKS AND HUB DRAINS. AS LAST RESORT PROVIDE
MECHANICAL TYPE TRAP PRIMER (PPP INC. "OREGON #1" TYPE). CONNECT TO NEAREST
WATER SERVING THAT AREA PER MANUFACTURER'S INSTALLATION INSTRUCTIONS. IN
JURISDICTIONS WHERE PRESSURE ACTIVATED MECHANICAL PRIMERS ARE NOT ALLOWED,
USE ELECTRONIC TRAP PRIMERS. COORDINATE POWER REQUIREMENTS WITH ELECTRICAL
CONTRACTOR. PROSET "TRAP GUARD" DEVICE MAY BE USED IN LIEU OF TRAP PRIMERS
WHEN ALLOWED BY LOCAL CODE AUTHORITY HAVING JURISDICTION. BEFORE USING
PROSET "TRAP GUARD" CONTRACTOR MUST OBTAIN WRITTEN APPROVAL FROM LOCAL
CODE AUTHORITY HAVING JURISDICTION AND PROVIDE COPIES TO ARCHITECT AND
ENGINEER.
2.
MANUFACTURERS:
ISIMET UTILITY CONTROLLER AND E-SERIES ENCLOSURE - (210) 654-8015 or
LAB SAFETY SYSTEMS UTILITY CONTROLLERS - (512-845-3528)
1
DO NOT ROUTE ANY PIPING ABOVE THIS AREA.
1.
2
CONNECT TO COLD WATER (CW) STUB PROVIDED BY CIVIL. FIELD VERIFY EXACT
LOCATION.
3
RE: CW BUILDING ENTRY DETAIL ON PLUMBING DETAIL SHEET(S).
4
RE: WATER HEATER DETAIL ON PLUMBING DETAIL SHEET(S) FOR WATER HEATER
AND HOT WATER RECIRCULATION PUMP PIPING.
5
CONNECT TO FIRE LINE (F) STUB PROVIDED BY CIVIL. FIELD VERIFY EXACT LOCATION
AND INVERT.
6
RE: FIRE LINE RISER SUPPORT DETAIL ON PLUMBING DETAIL SHEET(S).
7
SCIENCE ROOM UTILITY CONTROLLER ABOVE CEILING. REFERENCE NOTES ON THIS
SHEET.
8
CW DOWN TO IN-LINE RPZ BACKFLOW PREVENTOR ON WALL IN ACCESSIBLE
LOCATION. COORDINATE EXACT LOCATION WITH ARCHITECT AND EQUIPMENT.
ROUTE RELIEF FROM RPZ TO FLOOR SINK FOR ICEMAKER.
ELECTRICAL CONTRACTOR: PROVIDE A UTILITY CONTROLLER (1000 SERIES 12X9) AND
E-SERIES (E3112-EX) CONTACTOR ENCLOSURE FOR EMERGENCY SHUT-OFF OF POWER
(RECEPTACLES), COLD WATER, TEMPERED WATER AND GAS AS REQUIRED (VERIFY EXACT
UTILITIES REQUIRED IN EACH INDIVIDUAL ROOM WITH PLUMBING CONTRACTOR). PROVIDE
INDIVIDUAL CONTROL SWITCH FOR CW/HW/GAS/RECEPTACLES. EXHAUST FANS FOR HOODS
TO BE CONTROLLED FROM UTILITY CONTROLLER WITH KEY SWITCH TO ENABLE FAN SWITCH
ON HOOD. CONTACTOR ENCLOSURES TO BE MOUNTED ABOVE CEILING. ELECTRICAL
CONTRACTOR TO FURNISH AND INSTALL UTILITY CONTROLLER AND E-SERIES CONTACTOR
ENCLOSURE AND PROVIDE ALL 120 VOLT WIRING AND 24V WIRING BETWEEN CONTROLLER,
CONTACTOR ENCLOSURE AND EQUIPMENT. PROVIDE CONTACTOR ENCLOSURES FOR (12)
TWELVE CIRCUITS. ELECTRICAL CONTRACTOR TO ALSO PROVIDE 24 VOLT CONTROL WIRING
BETWEEN UTILITY CONTROLLER AND S-SERIES SOLENOID ENCLOSURE. INNER CONNECT
WITH FACP TO SHUT DOWN SERVICES. COORDINATE WITH FIRE ALARM CONTRACTOR.
PIPING SIZE FOR WATER MAIN DROPS AND MANIFOLD IN CHASE OR WALL TO REMAIN FULL
SIZE OF DROP INDICATED. REFERENCE FIXTURE CONNECTION SCHEDULE FOR INDIVIDUAL
LINE SIZE TO EACH FIXTURE.
3.
COORDINATE ALL WASTEWATER FLOOR PENETRATIONS AND PIPING PENETRATIONS WITH
STRUCTURAL PRIOR TO INSTALLATION. PIPING MAY BE OFFSET SLIGHTLY TO AVOID
STRUCTURAL CONFLICTS.
4.
2.
ROUTE VENT FROM EACH FIXTURE TO HORIZONTAL VENT HEADER IN CHASE/WALL OR TO
NEAREST COMMON VTR ABOVE CEILING. REFERENCE FIXTURE CONNECTION SCHEDULE
FOR INDIVIDUAL FIXTURE VENT SIZES. VENT HEADERS IN CHASE TO BE SIZED
ACCORDINGLY: 1 1/2" VENT UP TO 6 DRAIN FIXTURE UNITS MAXIMUM DEVELOPED LENGTH
OF 60 FEET (EXCEPT FOR WATER CLOSETS), 2" VENT UP TO 20 DRAIN FIXTURE UNITS
MAXIMUM DEVELOPED LENGTH OF 120 FEET, 3" VENT UP TO 84 DRAIN FIXTURE UNITS
MAXIMUM DEVELOPED LENGTH OF 212 FEET AND 4" VENT UP TO 256 DRAIN FIXTURE UNITS
MAXIMUM DEVELOPED LENGTH OF 300 FEET. BRANCH VENTS EXCEEDING 40 FEET IN
DEVELOPED LENGTH ARE TO BE INCREASED BY ONE PIPE SIZE. NO MORE THAN 1/3 OF THE
CODE PERMITTED DEVELOPED LENGTH SHALL BE IN HORIZONTAL POSITION. EXTEND
COMMON VENT UP THROUGH ROOF.
HOT (TEMPERED) AND COLD WATER REQUIRED UNLESS NOTED OTHERWISE ON PLUMBING FIXTURE
SCHEDULE. PROVIDE TEMPERATURE MIXING VALVE (ASSE 1070) AT THE FIXTURE.
IF HORIZONTAL VENT LENGTH EXCEEDS 20 FEET, INCREASE VENT SIZE TO TWO INCHES.
COMMERCIAL KITCHEN SINKS GET HOT WATER, REMAINDER TO BE PROVIDED WITH TEMPERATURE
MIXING VALVE (ASSE 1070) AT THE FIXTURE.
SHOWER VALVES TO BE BALANCED-PRESSURE, THERMOSTATIC OR COMBINATION
BALANCED-PRESSURE/THERMOSTATIC CONFORMING TO ASSE 1016.
5.
ROUTE ALL VENTS TO NEAREST COMMON VENT THRU ROOF (VTR) TO MINIMIZE ROOF
PENETRATIONS. VTR TO BE MINIMUM 15 FEET AWAY FROM OUTSIDE AIR INTAKES.
COORDINATE WITH MECHANICAL CONTRACTOR PRIOR TO INSTALLATION.
PLUMBING CONTRACTOR: PROVIDE PRE-ASSEMBLED S-SERIES (S-3113-24VAC-X-K-F-R-A-U)
SOLENOID ENCLOSURE WITH ALL CONTACTS RESET SOLENOID AND INTERFACE RELAYS FOR
EACH SCIENCE ROOM FOR EMERGENCY SHUT-OFF OF COLD WATER, TEMPERED WATER AND
GAS. EACH SOLENOID TO BE ASSEMBLED WITH THREADED BALL VALVE, UNIONS, "Y"
STRAINERS, SHOCK ARRESTOR, AND CAPPED ENDS FOR FIELD INSTALLATION. ENCLOSURE
SHALL BE NEMA 1, SURFACE MOUNT ABOVE CEILING. FIELD VERIFY EXACT MOUNTING
ARRANGEMENT. VERIFY EXACT UTILITIES REQUIRED IN EACH INDIVIDUAL ROOM .
9
SHUT-OFF VALVE FOR EMERGENCY SHOWER / EYEWASH. LEAVE VALVE IN OPEN
POSITION. REMOVE HANDLE AND TURN OVER TO OWNER.
3.
ELECTRICAL AND PLUMBING CONTRACTOR TO COORDINATE ALL REQUIREMENTS TO
PROVIDE A COMPLETE AND WORKABLE SYSTEM.
10
FIRE LINE OUT TO FIRE DEPARTMENT CONNECTION (FDC). CONNECT TO FIRE LINE
(F) STUB PROVIDED BY CIVIL. FIELD VERIFY EXACT LOCATION AND INVERT.
4.
PROVIDE FACTORY START-UP WITH PLUMBING AND ELECTRICAL CONTRACTOR PRESENT
AND SIGNED START-UP CERTIFICATE.
11
5.
WHEN EMERGENCY BUTTON IS DEPRESSED, POWER IS SHUT OFF TO ALL ANCILLARY
DEVICES.
ALL VALVES ABOVE CEILING TO BE LOCATED AS NEAR TO LIGHT FIXTURES AS
POSSIBLE. LIGHT FIXTURES ARE REMOVABLE AND THIS WILL BE UTILIZED AS ABOVE
CEILING ACCESS POINTS.
12
INSURE ADEQUATE SPACE (48" MIN.) IS LEFT FOR LADDER ACCESS TO MEZZANINE.
13
LOW PRESSURE GAS ROUTED ABOVE CEILING.
6.
ROOM EXHAUST CONTROLLED SEPARATELY BY TIMER SWITCH ON WALL PROVIDED BY
ELECTRICAL CONTRACTOR.
7.
COORDINATE WITH BUILDING B.M.S. SYSTEM AS REQUIRED FOR DAILY SHUT-DOWN SIGNAL.
ALL SCIENCE ROOM AND SCIENCE PREP ROOM
EMERGENCY SHOWERS, SINKS AND FAUCETS ARE TO
BE PROVIDED BY SCIENCE CASEWORK CONTRACTOR.
PLUMBING CONTRACTOR TO PROVIDE ROUGH-IN AND
CONNECTION TO SUPPLIES AND WASTE. FAUCETS TO
HAVE INTEGRAL VACUUM BREAKER OR OTHER MEANS
OF BACKFLOW PROTECTION.
FEC
ENSEMBLE
UNIFORM STORAGE
307
305
MECH / FIRE
306
W/D
RR
OFFICE
226
229
CUST
227
BAND HALL
304
RECEIVING
228
FEC
ELEC
230
PRACTICE ROOM
PRACTICE ROOM
BAND OFFICE
308
309
302
WAREWASH
225
COOLER
LIBRARY & REPAIR
PRACTICE ROOM
SOUND VEST.
PRACTICE ROOM
222
CORRIDOR
218A
303
COOKING
301
310
311
224
FREEZER
PREP
FEC
221
223
FEC
CORRIDOR
300
SCIENCE PREP
WH
VEST
VEST
410
406
MECH
WH
453
BOYS VARSITY LOCKERS
COACH'S OFFICE
411
MDF
214
220
SERVING
454
BIOLOGY
215
DRY STOR
WH
219
DW
WH
407
BOYS JV LOCKERS
403
COACH'S LOCKER
RR
408
CUST
216
409
FEC
GIRLS RR
F
ICE
TRAINING
402
SHOWERS
RESTROOMS
404
405
SHOWERS
450
412
RESTROOMS
413
CORRIDOR
STORAGE
BOYS RR
414
217
FEC
451
VEST
401
VEST
415
CORRIDOR
FEC
218
FEC
FEC
PHYS / ART
SCIENCE PREP
213
CHEMISTRY
210
211
DW
G:\2015\THRALL ISD - HIGH SCHOOL.084\84P3.02.dwg, 1/27/2016 3:30:39 PM, JESUS, DWG To PDF.pc3, ARCH full bleed E1 (30.00 x 42.00 Inches), 0.125:12
FEC
CHEM STOR
212
FLOOR PLAN - AREA B - PLUMBING
P3.02
8 OF 8