Product Bulletin 3630
Release A-EU, Effective February 2001
Scotchcal™ Series 3630
Translucent Film
Description
Limitations of End Uses
Advantages
The following uses and applications are specifically
NOT warranted.
•
Translucent cast vinyl film
•
Durable, dimensionally stable
•
Uniform color in both reflected and transmitted
light
•
57 colors (many with PANTONE®
simulations)
•
Low surface gloss eliminates glare
Application and End Uses
Scotchcal™ Translucent Film Series 3630 is
intended for making permanent, durable graphics
when used with the listed compatible products and
in the following applications. Any other application
is NOT warranted by 3M or covered by the
worldwide 3M™ MCS™ (Matched Component
System) Warranty unless 3M gives its prior written
approval for the application.
•
For interior or exterior use on:
- The listed compatible substrates
- Internally illuminated sign faces
- Internally illuminated awnings protected by
3M™ Scotchcal™ Overlaminate Film 3640
GPS or 3642 GPS.
•
•
For first surface application to 3M™
Panaflex™ Awning & Sign Facing 945 GPS
substrate and 3M™ Panaflex™ Enhanced
Image Sign Facing 645 EI substrate.
For thermoforming with rigid plastic surfaces
under well-controlled conditions as described
in Instruction Bulletin 5.16.
Page 1 of 5
Product Bulletin PB_3630 A-EU-Feb01
• 3M Commercial Graphics Division products are
not tested against automotive manufacturers’
specifications and are therefore not warranted for
use in fabricating graphics for automotive
Original Equipment Manufacturers (OEM).
• Application to competitive awning and sign
facing materials
• Application to substrates having coatings such as
silicone
• Graphics with more than two layers of film except
as described in the following Important Note
Important Note
A third layer of film on any one surface is warranted
only if the top layer is 3M™ Scotchcal™ Transparent
Films 3640 GPS or 3642 GPS and no more than two
layers of any film are even with the edges of the
substrate. Therefore:
3640GPS/3642GPS
Film Layer 2
Film Layer 1
Substrate
Extend Film Layer 3 1
inch beyond edges of
Film Layers 1 and 2
3640GPS/3642GPS
Film Layer 2
Film Layer 1
Extend Film Layer 3 to
the edges of substrate.
Substrate
3640GPS/3642GPS
Film Layer 2
Film Layer 1
Substrate
3640GPS/3642GPS
Film Layer 2
Film Layer 1
Substrate
Extend Film Layer 3
1 inch beyond edges of
Film Layers 1 and 2 and
Substrate, and wrap
Layer 3 around the back
of Substrate.
Compatible Products
Product
Color
PANTONE® Color
• 3M™ Panaflex™ Awning & Sign Facing 945
GPS
3630–73
Dark Red
NA
3630–74
Kumquat Orange
PANTONE 1375C
• 3M™ Panaflex™ Enhanced Image Sign Facing
645 EI
3630-75
Marigold
NA
3630–76
Holly Green
NA
• Additional rigid substrates such as flat acrylic,
polycarbonate*, butyrate, fiberglass, glass
3630–78
Vivid Rose
PANTONE 206C
3630–83
Regal Red
PANTONE 187C
• 3M™ Scotchcal™ Overlaminate Film 3640
GPS and 3642 GPS
3630–84
Tangerine
PANTONE 151C
3630–87
Royal Blue
PANTONE 274C
• 3M™ Scotchcal™ Translucent Film Series 3630
typically adheres to solar-grade polycarbonate
substrate. However, some lots of this substrate
may inhibit the adhesion of this film. Contact
3M Commercial Graphics Technical Service if
you have difficulty with this combination. See
Instruction Bulletin 5.7 for additional
information.
3630–97
Bristol Blue
PANTONE 294C
3630–106 Brilliant Green
PANTONE 376C
3630–108 Pink
PANTONE 224C
3630-109
PANTONE 181C
Lt. Rust Brown
3630–115 Lt. Lemon Yellow
PANTONE 3995C
3630–116 Bright Jade Green
NA
3630–118 Intense Magenta
PANTONE 241C
3630–121 Silver
PANTONE 877C
3630–125 Golden Yellow
PANTONE 1235C
Product Line
3630–126 Dark Emerald
Green
PANTONE 3435C
This bulletin does not contain detailed printing,
processing or application procedures for the
products described herein. The appropriate
instruction bulletin(s) may be obtained by
contacting your 3M sales representative.
3630–127 Intense Blue
PANTONE 300C
3630–128 Plum Purple
PANTONE 2622C
3630-129
PANTONE 471C
* Polycarbonate substrates may require drying
by baking before use. Refer to the
manufacturers’ instructions.
Product
Color
PANTONE
®
Color
Bronze
3630–131 Gold Metallic
PANTONE 873C
3630–133 Raspberry
PANTONE 220C
3630–005 Ivory
NA
3630-136
lime Green
PANTONE 368C
3630–015 Yellow
PANTONE 109C
3630-137
European Blue
PANTONE281C
3630–20
White
NA
3630–141 Gold Nugget
NA
3630–22
Black**
PANTONE Process
Black C
3630–143 Poppy Red
PANTONE 1788C
2X
3630–25
Sunflower
PANTONE 123C
3630–146 Lt. Kelly Green
PANTONE 347C
3630–26
Green
PANTONE 349C
3630–147 Lt. European Blue
NA
3630–33
Red
PANTONE 485C 2X
3630–149 Light Beige
PANTONE 468C
PANTONE 355C
3630–36
Blue
PANTONE 281C
3630–156 Vivid Green
3630–43
Light Tomato
Red
PANTONE 1788C 2X
3630–157 Sultan Blue
PANTONE 288C
3630–167 Bright Blue
PANTONE 2945C
3630–44
Orange
PANTONE 1655C
3630–236 Turquoise
PANTONE 3282C
3630–49
Burgundy
PANTONE 188C
3630–246 Teal Green
PANTONE 322C
3630–51
Silver Gray
PANTONE 439C
3630–317 Process Blue
PANTONE 299C 2X
3630–53
Cardinal Red
NA
3630-337
PANTONE 658C
3630–57
Olympic Blue
NA
3630–59
Dark Brown
PANTONE 4625C
3630–61
Slate Grey
NA
* This product is a simulation of a PANTONE®
identified color standard. Use current PANTONE
Color Reference Manuals for accurate color.
3630–63
Rust Brown
PANTONE 483C
3630-68
Rose Mauve
PANTONE 190C
3630–69
Duranodic**
PANTONE Black C
3630–71
Shadow Gray
PANTONE 409C
Page 2 of 5
Product Bulletin PB_3630 A-EU-Feb01
Evening Blue
* PANTONE® is a registered trademark of Pantone,
Inc.© Pantone, Inc. 1963, 1991.
** This film is opaque, not translucent.
Special colors are available on request. Pigment
durability and manufacturing limitations do not
permit exact matching of all color shades.
Characteristics
3M™ MCS™ Warranty periods in years
Property
Description
Film
0.05 mm, translucent vinyl
with protective top coat
Thickness (film and
adhesive)
0.075 – 0.10 mm
Film colors
Custom colors
Adhesive type
Pressure sensitive
Adhesive color
Clear
Liner
Translucent, synthetic liner
Application surfaces
Flat, without rivets
Minimum application
temperature
(air, film, substrate)
16°C
Effective Performance Life
Performance statements are based upon
representative experience obtained from testing
throughout Europe. Substrate selection and
preparation, maintenance of the marking and
exposure conditions will determine actual
performance.
The film’s warranted period will vary, depending
on which substrate the film is applied to. The
following matrix indicates the films intended use.
For other applications, contact your local 3M sales
representative.
Zone 1:
Northern & Central Europe
Zone 2:
Mediterranean Europe
Zone 3:
Northern Africa and Middle East
Warranted by 3M:
Film and
substrate
With overlaminate
Zone
Film,
overlay and
substrate
/
1
3640/3642
2
3
1
2
3
10
H 4
7
3
5
2
12
6
9
5
7
4
5
4
3
7
6
5
10
10
7
7
5
5
12
12
9
9
7
7
5
5
4
4
3
3
7
7
6
6
5
5
10
4
10
4
7
3
7
3
5
2
5
2
12
6
12
6
9
5
9
5
7
4
7
4
Metallic:
Ext. 1st surface V
Ext. 2nd surface V
5
5
4
4
3
3
7
7
6
6
5
5
Thermoformed acrylic
Colors:
Ext. 1st surface V
Ext. 2nd surface V
6
6
5
5
4
4
Substrates:
Panaflex™ 945 GPS
Colors:
Ext. 1st surface V
Metallic:
Ext. 1st surface
V
Panaflex™ 645 EI
Colors:
Ext. 1st surface V
Ext. 2nd surface V
Metallic:
Ext. 1st surface V
Ext. 2nd surface V
Flat acrylic
Colors:
Ext. 1st surface
V
H
nd
Ext. 2 surface V
H
Printed with ink
series:
1900
line inks
halftone
9700 UV
/
/
Ink clear:
5
4
4
3
3
2
1920
1920
7
5
3
9720
V - Vertical or within 10o of vertical applications.
H - Horizontal applications or more than 10o of
vertical.
Page 3 of 5
Product Bulletin PB_3630 A-EU-Feb01
Fabrication
Product Data
Vacuum Forming
Values given are typical and are not for use in
specifications. If a custom specification is desired, a
request should be submitted through your sales
representative. The data given below is for unprinted
film.
Special recommendation, limitations and
processing requirement for forming with applied
films is detailed in Instruction Bulletin 5.16. There
are specific unique healths and safety
considerations that must be understood prior to
vacuum forming faces using translucent films. Prior
to forming faces, it is important to review all
information contained in the Material Safety Data
Sheet (MSDS), on the box label and in the
instruction bulletins.
Physical Properties
Property
Metric Units
Thickness (ISO 4593)
0.08mm - 0.10mm
Tensile Strength (ISO
1184-1983)
0.9kg/cm at 23°C
3M™ Scotchcal™ Light Control Film 3635-30 and
-70 are not warranted for vacuum forming. If they
are vacuum formed, it must be done on a test and
approve basis.
Elongation (ISO 11841983)
100% at 23°C
Dimensional Stability
(FTM 14)
0.30mm
Cutting
Temperature Range*
-45°C to +77°C
Individual pieces can be hand cut, die cut, kiss cut
or cut with most computers driven cutting devices.
Multiple pieces can be cut using various
techniques, such as guillotine cutting and die
cutting.
Adhesion (anodized
aluminum)
0.7kg/cm
Adhesive
Transparent Pressure
Sensitive
Application
Temperature Range
16°C – 38°C
Premasking and Prespacing
Conditions
Unprocessed
General Premasking
General Prespacing
Series 1900 Inks
General Premasking
General Prespacing
3M Application Tapes
SCPM-19
SCPS-100
SCPM-19
SCPS-100
Application
These films may be applied using either the
detergent / water or dry application methods (hand
application or roll applicator). For hand
applications, the detergent / water application
method is preferred. Use of dry application by hand
may leave some dark streaks or bubbles that could
be visible in transmitted light.
Shelf Life, Storage, Shipping
and Maintenance
The shelf life of the film is 2 years and should be
applied within 2 years of the receipt of film if
unprocessed. Processed film should be applied
within 1 year of processing and within 2 years of
receipt of the film.
Health and Safety
Refer to the box labels and the Material Safety Data
Sheets for health and safety information on the
products referenced in this bulletin. Attention
vacuum formers, refer to vacuum forming section
above.
Page 4 of 5
Product Bulletin PB_3630 A-EU-Feb01
Chemical Resistance
Chemical Agent
Exposure
Time
Results
Water
24 hours
No effect
Mild Soap and Water
24 hours
No effect
20% Isopropyl Alcohol/ 10 min
80% Water
No effect
10% Hydrochloric Acid 10 min
No effect
10% Ammonium
Hydrox.
No effect
10 min
Important Notice
For Further Assistance
This bulletin provides technical information only.
For help on specific questions relating to 3M™
Scotchcal™ Translucent Film Series 3630, or any
other 3M Commercial Graphics Division products,
contact your local 3M Technical Service
representative or
All questions of warranty and liability relating to
this product are governed by the terms and
conditions of the sale, subject, where applicable, to
the prevailing law.
Before using, the user must determine the
suitability of the product for its required or
intended use, and the user assumes all risk and
liability whatsoever in connection therewith.
3M Related Literature
Listed below is related 3M Technical Literature
which may be of interest:
Subject
Bulleti
n No.
Instruction Bulletins
Design of markings
2.1
Premasking and prespacing
4.3
Surface preparation (Non-vehicular)
5.1
Application to
• Flat rigid signs
• Flat glass
• Panaflex™ 945 GPS and 645 EI
substrate
5.7
5.8
5.9
3M™ Screen Printing Ink Series 1900
3.11
3.12
3M™ Screen Printing Ink Series 9700UV 3.4
Scoring and cutting
4.1
Vacuum Thermoforming
5.16
Storage, handling, maintenance, removal
6.5
Product Bulletins
3M™ Screen Printing Ink Series 1900
1900
3M™ Screen Printing Ink Series 9700UV 9700
Warranties
Worldwide 3M™ MCS™ Warranty of products
Page 5 of 5
Product Bulletin PB_3630 A-EU-Feb01
3M Laboratories (Europe)
Zweigniederlassung der 3M Deutschland GmbH
- Commercial Graphics Carl-Schurz-Strasse 1
D - 41453 Neuss
Germany
Phone: +49 (0) 2131 14-3500
Fax: +49 (0) 2131 14-2377
The use of Trademark signs and brand names in this
bulletin is based upon US standards. These standards
may vary from country to country outside the U.S.A.