Installation Instructions for the
SS400 Series Temperature Compensated
Digital Hall-Effect Sensor ICs
GENERAL INFORMATION
PK 88700
Table 1. Absolute Maximum Ratings
CAUTION
ELECTROSTATIC
DISCHARGE DAMAGE
This component is sensitive
to electrostatic discharge
(ESD). Take normal ESD
precautions in handling this
product to prevent ESDinduced damage and/or
degradation.
Failure to comply with
these instructions may
result in product damage.
ISSUE 6
CAUTION
ELECTROSTATIC
SENSITIVE
DEVICES
DO NOT OPEN OR HANDLE
EXCEPT AT A
STATIC FREE WORKSTATION
ESD SENSITIVITY:
CLASS 3
Characteristic
Supply voltage
Parameter
-1 Vdc to +30 Vdc
Voltage externally
applied to output
+30 Vdc max. (OFF only)
-0.5 Vdc min. (OFF or ON)
Output ON current
see Table 2
Operating temperature -40 °C to 150 °C [-40 °F to 302 °F]
Storage temperature
-50 °C to 150 °C [-58 °F to 302 F]
Magnetic flux
no limit; circuit cannot be damaged
by magnetic overdrive
NOTICE
SOLDERING/ASSEMBLY
CAUTION
IMPROPER SOLDERING
Ensure leads are supported during any forming/ shearing
operation so that they are not stressed inside the plastic
case.
Limit exposure to high temperatures.
Failure to comply with these instructions may result in
product damage.
PC board wave soldering temperature is 250 °C to 260 °C
[482 °F to 500 °F] peak for 3 s max.
CLEANING
CAUTION
IMPROPER CLEANING
Do not use pressure wash. High-pressure stream could force
contaminants into the package.
Failure to comply with these instructions may result in
product damage.
Absolute maximum ratings are the extreme limits that the
device will withstand without damage to the device.
However, the electrical and mechanical characteristics are
not guaranteed as the maximum limits (above
recommended operating conditions) are approached, nor
will the device necessarily operate at absolute maximum
ratings.
Table 2. Output Current Absolute Limits
Supply Voltage
Output Current
-1 Vdc to 24 Vdc
50 mA max.
24 Vdc to 25 Vdc
37 mA max.
25 Vdc to 26 Vdc
33 mA max.
26 Vdc to 27 Vdc
28 mA max.
27 Vdc to 28 Vdc
24 mA max.
28 Vdc to 29 Vdc
19 mA max.
29 Vdc to 30 Vdc
15 mA max.
Figure 1. Block Diagram
Use agitated rinse to clean the sensor.
Table 3. Operating Characteristics (over operating voltage and temperature, unless otherwise noted)
Characteristic
Min.
Supply voltage
3.8 Vdc
Typ.
Current consumption
Supply current (operated at 25 °C, Vs = 5 V)
Max.
10 mA
6.5 mA
Output voltage (operated)
0.40 Vdc
Output current (operated)
20 mA
Output leakage current (released)
10 A
Output switching time:
rise, 10% to 90%
fall, 90% to 10%
Sensing and Control
Note
30 Vdc
0.05 s
0.15 s
1.5 s
1.5 s
sinking, 20 mA max.
VCC = 12 V,
RL = 1.6 k ,
CL = 20 pF
SS400 Series Temperature Compensated
Digital Hall-Effect Sensor ICs
Table 4. Magnetic Characteristics
Catalog Listing
Temperature
SS411A
SS411A-L
Operating
Characteristic SS411A-T2
SS411A-T3
Bipolar
-40 C
[-40 F]
0 C
[32 F]
25 C
[77 F]
85 C
[185 F]
125 C
[257 F]
150 C
[302 F]
SS413A
SS413A-L
SS413A-T2
SS413A-T3
SS441A
SS441A-L
SS441A-T2
SS441A-T3
SS443A
SS443A-L
SS443A-T2
SS443A-T3
SS449A
SS449A-L
SS449A-T2
SS449A-T3
SS461A
SS461A-L
SS461A-T2
SS461A-T3
SS466A
SS466A-L
SS466A-T2
SS466A-T3
Bipolar
Unipolar
Unipolar
Unipolar
Latching
Latching
min. op.
NS
NS
50 G
110 G
285 G
5G
100 G
max. op.
70 G
140 G
135 G
215 G
435 G
110 G
200 G
min. rel.
-70 G
-140 G
20 G
80 G
210 G
-110 G
-200 G
max. rel.
NS
NS
120 G
190 G
360 G
-5 G
-100 G
min. dif.
15 G
20 G
15 G
25 G
30 G
50 G
200 G
min. op.
NS
NS
53 G
110 G
305 G
5G
100 G
max. op
65 G
140 G
117 G
190 G
400 G
90 G
185 G
min. rel.
-65 G
-140 G
20 G
80 G
230 G
-90 G
-185 G
max. rel.
NS
NS
99 G
165 G
325 G
-5 G
-100 G
min. dif.
15 G
20 G
15 G
25 G
30 G
50 G
200 G
min. op.
NS
NS
55 G
110 G
310 G
10 G
100 G
max. op.
60 G
140 G
115 G
180 G
390 G
85 G
180 G
min. rel.
-60 G
-140 G
20 G
75 G
235 G
-85 G
-180 G
max. rel.
NS
NS
95 G
155 G
31 G5
-10 G
-100 G
min. dif.
15 G
20 G
20 G
25 G
30 G
50 G
200 G
min. op.
NS
NS
45 G
90 G
290 G
110 G
95 G
max. op.
60 G
140 G
120 G
180 G
400 G
85 G
180 G
min. rel.
-60 G
-140 G
15 G
70 G
215 G
-85 G
-180 G
max. rel.
NS
NS
105 G
165 G
325 G
-10 G
-95 G
min. dif.
12 G
20 G
15 G
15 G
30 G
50 G
190 G
min. op.
NS
NS
40 G
80 G
270 G
5G
80 G
max. op.
65 G
140 G
123 G
190 G
410 G
100 G
180 G
min. rel.
-65 G
-140 G
15 G
60 G
200 G
-100 G
-180 G
max. rel.
NS
NS
115 G
180 G
340 G
-5 G
-80 G
min. dif.
12 G
20 G
8G
10 G
30 G
50 G
160 G
min. op.
NS
NS
35 G
65 G
260 G
5G
70 G
max. op
70 G
140 G
125 G
200 G
420 G
110 G
185 G
min. rel.
-70 G
-140 G
10 G
55 G
185 G
-110 G
-185 G
max. rel.
NS
NS
120 G
195 G
345 G
-5 G
-70 G
min. dif.
10 G
20 G
5G
5G
30 G
50 G
140 G
NOTICE
Bipolar Hall-effect sensors may have an initial output in either the ON or OFF state if powered up with an applied magnetic field in
the differential zone (applied magnetic field >Brp and <Bop). Honeywell recommends allowing 10 µs for output voltage to stabilize
after supply voltage has reached 5 V.
2 Honeywell
Sensing and Control
SS400 Series Temperature Compensated
Digital Hall-Effect Sensor ICs
Figure 5. SS400 Series Mounting Dimensions (For reference only. mm/[in].)
Straight Leads, 14,99 mm [0.59 in]) Long
Straight Leads, 18,67 mm [0.735 in] Long
SS411A, SS413A, SS441A, SS443A, SS449A, SS461A,
SS411A-L, SS413A-L, SS441A-L, SS443A-L, SS449A-L,
SS466A
SS461A-L, SS466A-L
4,1
[0.16]
HALL
1,7
ELEMENT [0.07]
CENTER
2,5
[0.10]
XXX
4,1
[0.16]
1,6
[0.06]
3,0
[0.12]
NS
XXX
HALL
1,7
ELEMENT [0.07]
CENTER
2,5
[0.10]
1,6
[0.06]
3,0
[0.12]
NS
0,64
[0.025]
0,64
[0.025]
14,99
[0.59]
18,669
[0.735]
+
1,3
[0.05]
–
0
0,38
[0.015]
0,3
[0.015]
0,76
[0.03]
–
1,3 +
[0.05]
Straight Leads, 14,99 mm [0.59 in]) long, on Tape
SS411A-T3, SS413A-T3, SS441A-T3, SS443A-T3, SS449AT3, SS461A-T3, SS466A-T3
0,38
[0.015]
0,3
[0.015]
0,76
[0.03]
Formed Leads, 14,99 mm [0.59 in]) long, on Tape
SS411A-T2, SS413A-T2, SS441A-T2, SS443A-T2, SS449AT2, SS461A-T2, SS466A-T2
4,1
[0.16]
ADHESIVE TAPE
2,5
[0.10]
22,3
[0.88]
6,0
[0.23]
0
HALL
1,7
ELEMENT [0.07]
CENTER
1,6
[0.06]
XXX
3,0
[0.12]
NS
9,0
[0.35]
18,0
[0.71]
0,64
[0.025]
14,99
[0.59]
6,3
[0.25]
12,7
[0.50]
1,3
[0.05]
Ø 3,99
[0.16]
+
2,54
[0.10]
–
0
0,38
[0.015]
0,3
[0.015]
0,76
[0.03]
ADHESIVE TAPE
22,3
[0.88]
6,0
[0.23]
9,0
[0.35]
18,0
[0.71]
2,5
[0.10]
6,3
[0.25]
12,7
[0.50]
3 Honeywell
Sensing and Control
Ø 3,99
[0.16]
SS400 Series Temperature Compensated
Digital Hall-Effect Sensor ICs
Figure 4. Electronic Diagrams
WARNING
WARNING
PERSONAL INJURY
MISUSE OF DOCUMENTATION
DO NOT USE these products as safety or emergency stop
devices or in any other application where failure of the
product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
The information presented in this application note is for
reference only. Do not use this document as a product
installation guide.
Complete installation, operation, and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
WARRANTY/REMEDY
Honeywell warrants goods of its manufacture as being free of
defective materials and faulty workmanship. Honeywell s
standard product warranty applies unless agreed to otherwise
by Honeywell in writing; please refer to your order
acknowledgement or consult your local sales office for specific
warranty details. If warranted goods are returned to Honeywell
during the period of coverage, Honeywell will repair or replace,
at its option, without charge those items it finds defective. The
foregoing is buyer s sole remedy and is in lieu of all other
warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special,
or indirect damages.
While we provide application assistance personally, through
our literature and the Honeywell web site, it is up to the
customer to determine the suitability of the product in the
application.
Specifications may change without notice. The information we
supply is believed to be accurate and reliable as of this printing.
However, we assume no responsibility for its use.
SALES AND SERVICE
Honeywell serves its customers through a worldwide network
of sales offices, representatives and distributors. For
application assistance, current specifications, pricing or name
of the nearest Authorized Distributor, contact your local sales
office or:
E-mail: info.sc@honeywell.com
Internet: www.honeywell.com/sensing
Phone and Fax:
Asia Pacific
+65 6355-2828
+65 6445-3033 Fax
Europe
+44 (0) 1698 481481
+44 (0) 1698 481676 Fax
Latin America
+1-305-805-8188
+1-305-883-8257 Fax
USA/Canada
+1-800-537-6945
+1-815-235-6847
+1-815-2
Sensing and Control
Honeywell
1985 Douglas Drive North
Golden Valley, MN 55422
www.honeywell.com/sensing
88700-6-EN
April 2012
Copyright © 2012 Honeywell International Inc. All rights reserved.